all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Manual | Users Manual | 1.38 MiB | October 06 2003 | |||
1 | Cover Letter(s) | October 06 2003 | ||||||
1 | Cover Letter(s) | October 06 2003 | ||||||
1 | External Photos | October 06 2003 | ||||||
1 | Internal Photos | October 06 2003 | ||||||
1 | ID Label/Location Info | October 06 2003 | ||||||
1 | Operational Description | October 06 2003 | ||||||
1 | Cover Letter(s) | October 06 2003 | ||||||
1 | RF Exposure Info | October 06 2003 | ||||||
1 | ID Label/Location Info | October 06 2003 | ||||||
1 | Test Report | October 06 2003 | ||||||
1 | Test Setup Photos | October 06 2003 |
1 | Manual | Users Manual | 1.38 MiB | October 06 2003 |
ASUS SpaceLink WL-100g WLAN PC Card Users Manual A R I L N K Copyright Information No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except docu-
mentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS). ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-
POSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPE-
CIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUD-
ING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is re-
paired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, IN-
CLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Copyright 2003 ASUSTeK COMPUTER INC. All Rights Reserved. Product Name:
Manual Revision:
Release Date:
ASUS SpaceLink WL-100g WLAN PC Card 1 March 2003 2 ASUS SpaceLink WL-100g WLAN PC Card Copyright Information 150 Li-Te Road, Peitou, Taipei, Taiwan 112
+886-2-2894-3447
+886-2-2894-3449 info@asus.com.tw ASUSTeK COMPUTER INC. (Asia-Pacific) Address:
General Tel:
General Fax:
General Email:
Technical Support
+886-2-2890-7121 (English) MB/Others (Tel):
Notebook (Tel):
+886-2-2890-7122 (English) Desktop/Server (Tel): +886-2-2890-7123 (English) Support Fax:
Support Email:
Web Site:
Newsgroup:
+886-2-2890-7698 tsd@asus.com.tw www.asus.com.tw cscnews.asus.com.tw ASUS COMPUTER INTERNATIONAL (America) Address:
6737 Mowry Avenue, Mowry Business Center, Building 2, Newark, CA 94560, USA
+1-510-608-4555 tmd1@asus.com General Fax:
General Email:
Technical Support Support Fax:
Notebook (Tel):
Web Site:
Support Email:
+1-510-608-4555 1-877-918-ASUS (2787) www.asus.com tsd@asus.com Harkortstr. 25, 40880 Ratingen, BRD, Germany
+49-2102-442066 sales@asuscom.de (for marketing requests only) ASUS COMPUTER GmbH (Europe) Address:
General Fax:
General Email:
Technical Support Support Hotline:
Notebook (Tel):
Support Fax:
Support (Email):
Web Site:
MB/Others: +49-2102-9599-0
+49-2102-9599-10
+49-2102-9599-11 www.asuscom.de/de/support (for online support) www.asuscom.de ASUS SpaceLink WL-100g WLAN PC Card 3 Safety Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the follow-
ing two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING! The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to con-
nect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Canadian Department of Communications This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Cana-
dian Department of Communications. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. 4 ASUS SpaceLink WL-100g WLAN PC Card Table of Contents 1. Introduction ............................................................................. 7 1.1 Overview ...................................................................................... 7 1.2 Package Contents........................................................................ 8 2. Installation ............................................................................... 9 2.1 Installing Drivers for Windows ...................................................... 9 2.1.1 Verifying Installation ........................................................ 11 2.2 Orientating the Antenna ............................................................. 13 2.3 Verifying the TCP/IP Protocol .................................................... 14 2.3.1 Installing the TCP/IP Protocol ......................................... 15 2.3.2 Configuring TCP/IP Properties ....................................... 16 2.3.3 Configuring Advanced TCP/IP Properties ...................... 17 2.3.4 Verifying TCP/IP Settings ............................................... 17 2.4 Installing Drivers for Windows CE.............................................. 18 2.5 Installing Drivers for Linux.......................................................... 18 2.6 Reading the Wireless LAN PC Card LEDs ................................ 19 2.7 Installing ASUS SpaceLink PC Card Utilities ............................. 20 3. Software Reference .............................................................. 22 3.1 Overview .................................................................................... 22 3.2 Windows XP Wireless Options .................................................. 23 3.3 Control Center............................................................................ 24 3.4 Wireless Settings ....................................................................... 26 More than one ASUS SpaceLink Card ...................................... 27 3.4.1 Status - Status Tab ......................................................... 27 3.4.2 Status - Connection Tab ................................................. 30 3.4.3 Status - IP Config Tab ..................................................... 31 3.4.4 Config - Basic Tab .......................................................... 32 3.4.5 Config - Encryption Tab .................................................. 35 3.4.6 Config - Advanced Tab ................................................... 38 3.4.7 Survey - Site Survey Tab ................................................ 40 3.4.8 About - Version Info Tab ................................................. 41 3.4.9 Link Status ...................................................................... 42 ASUS SpaceLink WL-100g WLAN PC Card 5 Table of Contents 3.5 Mobile Manager ......................................................................... 43 3.5.1 Main Window .................................................................. 44 3.5.2 Using New Configuration Wizard .................................... 47 3.5.3 Using Edit Configuration ................................................. 48 3.6 Site Monitor ................................................................................ 56 3.6.1 Starting Site Monitor ....................................................... 56 3.6.2 Main Screen ................................................................... 56 3.6.3 Monitor ............................................................................ 57 3.7 Live Update ................................................................................ 58 3.8 Windows XP Wireless Properties .............................................. 60 4. Troubleshooting .................................................................... 63 5. Glossary ................................................................................. 65 6 ASUS SpaceLink WL-100g WLAN PC Card 1 r e t p a h C Chapter 1 - Introduction 1. Introduction 1.1 Overview Thank you for purchasing the ASUS SpaceLink PC Card. The ASUS SpaceLink PC Card is a wireless network interface card (NIC) for any com-
puter equipped with a Personal Computer Memory Card International Asso-
ciation (PCMCIA) Type II socket. ASUS SpaceLink PC Card conforms to the PCMCIA release 2.x standard and is designed to be fully compliant with the IEEE 802.11b wireless local area network (Wireless LAN) standard. As a result of the completion of the standard, the interoperability of Wireless LAN products among multiple manufacturers will be guaranteed. The ASUS SpaceLink PC Card product provides high-speed, standards-
based Wireless LAN solutions. Supporting data rates up to 11 Mbps, with automatic fallback to 5.5, 2, and 1 Mbps. It operates in the unlicensed 2.4 GHz frequencies called the Instrumentation, Science, and Medical (ISM) band. Unlicensed means free of charge to users. The ASUS SpaceLink PC Card configuration utility is a user-friendly application that helps you quickly setup multiple roaming nodes using the ASUS SpaceLink PC Card. You can even export the configuration settings to a file and import them to other computers for fast multiple installations. Wireless LANs are complementary extensions to existing wired LANs, offering complete mobility while maintaining continuous network connec-
tivity to both corporate and home Intranets. They add a new level of conve-
nience for LAN users. PC users stay connected to the network anywhere throughout a building without being bound by a LAN wire. This is accom-
plished through the use of a device known as the Access Point (AP). By making use of AP in the office, you can easily establish mobile network connections to the enterprise Intranet or Internet. Moreover, you can bring your ASUS SpaceLink PC Card home to make your home-networking dream come true! A home-dedicated AP, with built-in Internet gateway capability, allows your family to share a broadband Modem and one ISP account si-
multaneously with no excessive, tedious ties! Connected anywhere, at any time, your family will feel closer by the invisible magic of the ASUS SpaceLink PC Card!
ASUS SpaceLink WL-100g WLAN PC Card 7 Chapter 1 - Introduction C h a p t e r 1 1.2 Package Contents When you receive the Wireless LAN package, it should contain the follow-
ing items:
ASUS SpaceLink PC Card (PCMCIA Type II) Users Manual CD-ROM Disc (Windows/Linux drivers, utilities, manual) If any of the above items are not included or damaged, contact your local dealer for instructions. 8 ASUS SpaceLink WL-100g WLAN PC Card Chapter 2 - Installation Installation 2. This chapter explains how to install the ASUS SpaceLink PC Card hard-
ware, drivers, and utilities. Although desktop PCs may have a PCMCIA slot, this manual will concentrate on Notebook PCs. The product is de-
signed to operate in Windows Me, 2000, and XP. Examples in this manual will be that of Windows ME. Complete the following steps to install the ASUS SpaceLink PC Card. 1. Install the ASUS SpaceLink PC Card. 2. Install the ASUS SpaceLink PC Card Driver 3. Install the TCP/IP protocol. 4. Install the ASUS SpaceLink PC Card Utilities 2.1 Installing Drivers for Windows 1. Turn ON your computer and enter Windows. 2. Insert the ASUS SpaceLink PC Card into a PCMCIA Type II slot with the connector side first. The LNK and AIR LEDs represent the top side and the MAC address sticker represents the bottom side. Push the PC Card into the slot until it is firmly seated. 2 r e t p a h C I A R L N K Air LED Link LED CAUTION: Make sure that you carefully align the ASUS SpaceLink PC Card into the PC Card socket. Forcing a misaligned PC Card will damage the PC Card or the computer. ASUS SpaceLink WL-100g WLAN PC Card 9 C h a p t e r 2 Chapter 2 - Installation 3. Windows will automatically detect the ASUS SpaceLink PC Card once it is inserted into the PCMCIA slot. Windows will display a New Hard-
ware Found dialog box and guide you through installing the driver. If you previously installed the ASUS SpaceLink PC Card Utility/Driver, Windows will find the driver for the PC Card in its system folder. Oth-
erwise, Windows will open a Add New Hardware Wizard dialog. The dialog will tell you that Windows will search for new drivers for the PC Card. Click Next to continue. 4. Select Search for the best driver for your device (Recommended) and then click Next. 5. Specify the location of the drivers for your operation system and click Next. Windows 98 - [CD]:\Driver\Win98 Windows Me - [CD]:\Driver\WinMe Windows 2000 - [CD]:\Driver\Win2K Windows XP - [CD]:\Driver\WinXP Where [CD] represents the driver letter of your CD-ROM drive. 6. Wait while Windows searches for the device driver for the ASUS SpaceLink PC Card. When Windows finds the driver ASUS SpaceLink WL-100G WLAN PC Card, click Next. 7. During the installation, Windows may prompt you to insert the Win-
dows Operating System CD which contains some driver files. Insert your Windows setup disc and type the path if necessary and click Yes. Windows will start copying the necessary files. 8. When the installation procedure is completed, click Finish. 9. When prompted, restart your computer. 10 ASUS SpaceLink WL-100g WLAN PC Card Chapter 2 - Installation 2.1.1 Verifying Installation Windows ME 2 r e t p a h C 1. Right-click My Computer on the desktop and select Properties. 2. Click Device Manager and look under Network adapters for Wireless LAN PC Card. ASUS SpaceLink WL-100g WLAN PC Card 11 Chapter 2 - Installation Windows XP C h a p t e r 2 1. Open the Control Panel through the Start 2. Double-click System icon. menu. 3. Click Device Manager on the Hardware 4. Click Network adapters. page. 12 ASUS SpaceLink WL-100g WLAN PC Card Chapter 2 - Installation 2.2 Orientating the Antenna The ASUS SpaceLink PC Card has two integrated antennas, one external omnidirectional antenna and the other is a built-in diversity antenna. It is recommended that you adjust the external antenna straight up for maxi-
mum range and higher link quality. Lower the external antenna when trans-
porting your Notebook PC. 2 r e t p a h C Internal diversity antenna Inserted ASUS SpaceLink PC Card - Antenna Down External omnidirectional antenna Inserted ASUS SpaceLink PC Card - Antenna Up ASUS SpaceLink WL-100g WLAN PC Card 13 Chapter 2 - Installation 2.3 Verifying the TCP/IP Protocol Windows ME For the ASUS SpaceLink PC Card to work, you must have the TCP/IP protocol installed. Follow the procedure here to verify the protocol. C h a p t e r 2 1. Right-click My Network Places on the desktop and select Properties. 2. Scroll down and look for TCP/IP -> ASUS SpaceLink WL-100g WLAN PC Card Windows XP 1. Double-click System icon in the Control Panel. 3. Look for Internet Protocol (TCP/IP). 2. Right click ASUS Spacelink WL-100G... and select Properties. 14 ASUS SpaceLink WL-100g WLAN PC Card Chapter 2 - Installation 2.3.1 Installing the TCP/IP Protocol Windows ME If your operating system does not have the TCP/IP protocol installed, you must do so to use the ASUS SpaceLink PC Card. 1. From the screen above, click the Add button. 2. Select Protocol and click Add. 3. Select Microsoft | TCP/IP and click OK 2 r e t p a h C Windows XP Windows XP operating system will install TCP/IP by default and will not show in the protocols to add. ASUS SpaceLink WL-100g WLAN PC Card 15 Chapter 2 - Installation 2.3.2 Configuring TCP/IP Properties Windows ME 1. Select TCP/IP -> ASUS SpaceLink WL-100G WLAN PC Card. 2. Click Properties button and IP Address tab. If your Access Point is connected to a network with a DHCP server, the default setting Obtain an IP address automatically should work. If your network does not automatically assign IP addresses, select Specify an IP address and type in the IP address and Subnet Mask as provided by your network administrator. If you want to route traffic through an IP sharing device, you have to setup the ASUS SpaceLink PC Card in the same Subnet as that of Access Point. C h a p t e r 2 1. This works for DHCP enabled networks. 2. The numbers here are for example only. Windows XP 1. This works for DHCP enabled networks. 2. If IP information is required, you can enter it in the Alternate Configuration in XP. 16 ASUS SpaceLink WL-100g WLAN PC Card Chapter 2 - Installation 2.3.3 Configuring Advanced TCP/IP Properties Windows ME If you want to route traffic through an IP sharing device for your Access Point, you have to set the default gateway address. 2 r e t p a h C 1. On the Gateway page, enter the address and click Add. 2. On the DNS Configuration page, enter the required information, click Add, and OK. 3. If Windows asks to restart your computer now, press Yes. 2.3.4 Verifying TCP/IP Settings Windows ME: Run winipcfg from the Start menu to verify TCP/IP settings. Windows XP: Use ipconfig from the command prompt to verify settings. ASUS SpaceLink WL-100g WLAN PC Card 17 Chapter 2 - Installation 2.4 Installing Drivers for Windows CE The ASUS SpaceLink WLAN Card drivers can be installed in Windows CE 3.0 or later device. ActiveSync must be installed in your Windows com-
puter (desktop or Notebook PC). 1. Connect the Pocket PC to your computer. Once it detects the link, ActiveSync window will open. 2. Insert the ASUS SpaceLink PC Card support CD into your computer. 3. From the autorun menu, click Installation for Windows CE. You may also run SpaceLink.exe from the WinCE folder in the support CD. 4. Follow the on-screen instructions to complete the installation. 5. Perform a soft reset of you Windows CE device. 6. 7. Enter the network settings when prompted. Insert the ASUS SpaceLink PC Card into your Windows CE device. 2.5 Installing Drivers for Linux Linux users must browse to the Linux folder in the support CD. For de-
tailed information, refer to Readme.txt in the same folder. Linux driver provided by AbsoluteValue Systems, Inc. All Rights Reserved. C h a p t e r 2 18 ASUS SpaceLink WL-100g WLAN PC Card Chapter 2 - Installation 2.6 Reading the Wireless LAN PC Card LEDs The part of the ASUS SpaceLink PC Card that protrudes out of the PCMCIA socket consists of two LEDs that indicate the status of the ASUS SpaceLink PC Card . A R I L N K Air LED Link LED 2 r e t p a h C Air LED The Air LED indicates that there are packets being transmitted. Link LED The Link LED is used to indicate the status of the ASUS SpaceLink PC Card. Solid Green: The ASUS SpaceLink PC Card is associated with an Ac-
cess Point. Blinking: The ASUS SpaceLink PC Card is attempting to associate with an Access Point. Off: There are errors during the Power-ON Self-Test. ASUS SpaceLink WL-100g WLAN PC Card 19 Chapter 3 - Reference 2.7 Installing ASUS SpaceLink PC Card Utilities 1. Insert the ASUS SpaceLink PC Card support CD and an autorun menu will appear. If your autorun is disabled. Double click SETUP.EXE in the root directory of the support CD. C h a p t e r 3 2. From the autorun menu, choose an installation language if necessary and click Install ASUS WLAN Card Utilities. 3. Follow the on-screen instructions to complete the installation. Note: The first link - ASUS WLAN Card Installation Instructions is only an information page on installing the driver which is already ex-
plained in detail in the previous section of this manual. 20 ASUS SpaceLink WL-100g WLAN PC Card Installing ASUS SpaceLink PC Card Utilities (Cont) Chapter 2 - Installation Windows ME 1. Click Next on the Welcome screen. 2. Click Yes after reading the License Agreement. 2 r e t p a h C 3. Browse to another Destination Directory or click Next to use the default. 4. Enter another Program Folder name or click Next to use the default. 6. When Setup is complete, click Finish to exit the installation wizard. Several shortcuts will be created which can be accessed through Start. ASUS SpaceLink WL-100g WLAN PC Card 21 Chapter 3 - Reference 3. Software Reference 3.1 Overview The ASUS SpaceLink PC Card software includes five groups of utilities. Control Center Makes it easy to launch applications and activate network location settings. Wireless Settings Allows users to control the ASUS SpaceLink PC Card. Mobile Manager A convenient tool to setup and manage network location settings. Site Monitor Measures the signal-to-noise (SNR) values of all wire-
less networks. This tool is used for determining the best placement of Access Points to provide the most efficient coverage in a wireless net-
work. Live Update Provides automatic driver and firmware update through the Internet. C h a p t e r 3 22 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.2 Windows XP Wireless Options The wireless options shown below is only available for Windows XP. The first time you run the Control Center utility, it will automatically show. Select one of the three radio buttons to decide your Windows XP wireless networking environment. Use XP and ASUS utilities together Use both Windows XP and ASUS utilities together to configure the ASUS SpaceLink PC Card. Only use XP wireless function Only use Windows XP wireless network settings to configure the ASUS SpaceLink PC Card. Only use ASUS utilities and disable XP wireless function Only use ASUS SpaceLink PC Card utilities to configure the ASUS SpaceLink PC Card. 3 r e t p a h C You can return to the Wireless Option setting at any time by left clicking the control center icon and choosing Wireless Option. ASUS SpaceLink WL-100g WLAN PC Card 23 Chapter 3 - Reference 3.3 Control Center Control Center is an application that makes it easy to launch applications and activate network location settings. Control Center starts automatically when the system boots. Whenever Control Center is running, you will see a Control Center icon displayed on the Windows taskbar. Starting the Control Center manually Click the Windows Start button, select Programs, select ASUS WLAN Card Utilities, and then click ASUS WLAN Control Center. or Double click the Control Center icon on the desktop. Using the Control Center Taskbar 1. The Control Center Taskbar menu display the following information:
The link quality of the ASUS SpaceLink PC Card (Excellent, Good, Fair, Poor, Not Linked) Whether the ASUS SpaceLink PC Card is connected to the Internet
(Blue: Connected, Gray: Not Connected) C h a p t e r 3 Taskbar Icon and Status Taskbar Left-Click Menu Taskbar Right-Click Menu 24 ASUS SpaceLink WL-100g WLAN PC Card Wireless Status Icons (on the taskbar) Chapter 3 - Reference Excellent link quality and connected to Internet (Infrastructure) Good link quality and connected to Internet (Infrastructure) Fair link quality and connected to Internet (Infrastructure) Poor link quality and connected to Internet (Infrastructure) Not linked but connected to Internet (Infrastructure) Excellent link quality but not connected to Internet (Infrastructure) Good link quality but not connected to Internet (Infrastructure) Fair link quality but not connected to Internet (Infrastructure) Poor link quality but not connected to Internet (Infrastructure) Not linked and not connected to Internet (Infrastructure) 3 r e t p a h C Linked (Ad Hoc) Not Linked (Ad Hoc) Connected to Internet 2. Right-clicking the taskbar icon shows the following menu:
Wireless Settings Launches Wireless Settings application. Mobile Manager Launches Mobile Manager application. Mobilize Activates network location settings. AP Manager Launches AP Manager application installed with the Wireless LAN Utilities. Preferences Customizes the way the Control Center program be-
haves. You can create a Control Center shortcut on the desktop. You can also set whether Control Center starts up with Windows. Exit Closes the Control Center program. ASUS SpaceLink WL-100g WLAN PC Card 25 Chapter 3 - Reference 3. Left-clicking the taskbar icon shows the following menu:
Wireless Radio On Turns the wireless radio ON. Wireless Radio Off Turns the wireless radio OFF. Search and Join View the properties of available Access Points within range. Wireless Option (Windows XP only) Sets your Windows XP wire-
less networking environment. 4. Double-clicking the taskbar icon:
Launches the Wireless Settings application. C h a p t e r 3 3.4 Wireless Settings Wireless Settings is an application that allows you to control your ASUS SpaceLink PC Card. Use Wireless Settings to View or Modify the configu-
ration settings and monitor the operational status of your PC Card. Once Wireless Settings is launched, you can see the tabbed property sheet. This property sheet is composed of tabbed pages, each with its own group of feature-specific settings. Starting Wireless Settings Open the Windows Control Panel, and then double-click the icon ASUS WLAN Card Settings icon. or Click the Windows Start button, select Programs, select ASUS WLAN Card Utilities, and then click Wireless Settings. or Click the Control Center icon on the Windows taskbar, a popup menu appears, and then click Wireless Settings. 26 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference More than one ASUS SpaceLink Card If you have more than one ASUS SpaceLink Card. You will be given a device selection window when you launch the Wireless Settings utility. 3.4.1 Status - Status Tab You can view the information about the ASUS SpaceLink PC Card from the general menu. These fields are blank if the ASUS SpaceLink PC Card does not exist. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 27 Chapter 3 - Reference Association State Shows the ASUS SpaceLink PC Card association status as follows:
Connected The station is now associated with one wireless LAN device. Also, indicates the MAC address of this device. Scanning... The station is now attempting to authenticate and associ-
ate with the desired Access Point. Disconnected If the link is connected and no beacon received, then the set adapter is no longer connected. INT_TEST_FAIL Interrupt test failed. NOT_AVAILABLE Cannot get PC Card status. SSID Shows the SSID that the ASUS SpaceLink PC Card is currently using. C h a p t e r 3 MAC address Indicates the hardware address of the ASUS SpaceLink PC Card. MAC address is a unique identifier for networking devices (typically written as twelve hexadecimal digits 0 through 9 and A through F, six hexadecimal numbers separated by colons, i.e. 00:01:24:F0:05:C0). This parameter is read-only and unique. Current Channel Shows the radio channel that the ASUS SpaceLink PC Card is currently using. Radio State Shows whether the wireless radio is ON or OFF. When the wireless radio is turned OFF, the following icon ap-
pears in the upper left of the Settings property page. When the wireless radio is turned ON, the following icon ap-
pears in the upper left of the Settings property page. 28 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference Button Enable Radio/Disable Radio You can click the Disable Radio button to turn OFF the wireless radio. When you click this button, the Radio State field indicates that the radio has been turned OFF and the remaining fields in this window display either a 0 or Not Applicable. Click this button again to turn the radio back ON. Rescan Force the radio to rescan all available channels. If your link qual-
ity or signal strength is poor, rescanning can be used to push the radio OFF a weak Access Point and search for a better link with another Access Point. This function will take some time. Change SSID Click on this to set the SSID. Search & Connect Click on this to connect to an available network. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 29 Chapter 3 - Reference 3.4.2 Status - Connection Tab You can view the current link statistics about the ASUS SpaceLink PC Card. These statistics are updated once per second and are valid only if the ASUS SpaceLink PC Card exists. C h a p t e r 3 Throughput Transmitted The number of bytes in frames that were transmitted. Received The number of bytes in frames that were received. Frame Error Transmitted The number of frames that were not successfully transmitted. Received The number of frames that were not successfully received. Connection Quality Link Quality Reflects the quality level related to the Access Point the station is currently connected to. Ratings are: Excellent, Good, Fair, and Poor. Signal Strength Reflects the signal level related to the Access Point the station is currently connected to. Ratings are: Excellent, Good, Fair, and Poor. Overall Connection Quality Derives from the current Link Quality and the current Signal Strength. A graph displays a connection quality range between 0 and 100 percent. 30 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.4.3 Status - IP Config Tab IP Config tab shows all the current network configuration information for the ASUS SpaceLink PC Card. Use it to verify your network settings. IP CONFIG will display all the current TCP/IP configuration values in-
cluding the IP address, subnet mask, default gateway and Windows Inter-
net Naming Service (WINS) and DNS configuration. 3 r e t p a h C Button IP Release - Releases the DHCP IP address for the ASUS SpaceLink PC Card. IP Renew - Renews the DHCP IP address for the ASUS SpaceLink PC Card. NOTE : The IP Release and IP Renew buttons can only be used on the ASUS SpaceLink PC Card that is configured with DHCP. ASUS SpaceLink WL-100g WLAN PC Card 31 Chapter 3 - Reference 3.4.4 Config - Basic Tab Lets you can change the ASUS SpaceLink PC Card configurations without rebooting your computer. C h a p t e r 3 Network Type Infrastructure Select the Infrastructure mode to establish a connec-
tion with an Access Point. Your computer is able to access wireless LAN and wired LAN (Ethernet), via an associated access point. The Channel field turns to Auto when Infrastructure is selected. Ad Hoc Select the Ad Hoc mode to communicate directly with each other without using an Access Point. An Ad Hoc network is typically formed quickly and easily without pre-planning. For example, share meeting notes between networked computers in a meeting room. 32 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference SSID Use the SSID filed to configure the SSID for the ASUS SpaceLink PC Card. You can enter a new SSID or select one from the drop-down list box. SSID stands for Service Set Identifier, which is a string used to identify a wire-
less LAN. You will only be able to connect Access Points which has the same SSID as the one you set. Use different SSIDs to segment the wireless LAN and increase security. SSIDs must all be printable characters and hav-
ing a maximum of 32 case sensitive characters, such as Wireless LAN. Set the SSID to any if you wish to allow your station to connect to any IEEE 802.11 Infrastructure Network it can find. When you set to any, Scanning... will begin and may take a long time. Use Sur-
vey to view all Access Points within range and their SSIDs. Channel Using the Channel field to select the radio channel for ASUS SpaceLink PC Card. In an infrastructure network, your PC Card will automatically select the correct frequency channel required to communicate with an Access Point, this parameter will be fixed in Auto and cannot be changed. In an Ad Hoc network, you can decide the channel number for the ASUS SpaceLink PC Card. Any ASUS SpaceLink PC Card can communicate in the same net-
work if each has the same frequency channel setting. The radio channels you may use depend on the regulations in your country. For United States (FCC) and Canada (IC), channels 1 to 11 are supported. For Europe (ETSI) except Spain and France, channels 1 to 13 are supported. For Spain channel 10 and 11 are supported. For France, channels 10 to 13 are supported. For operation in Japan (MKK), channels 1 to 14 are supported. Data Rate Fully Auto Automatic transmit data rate falls back to 1, 2, 5.5, or 11 megabits per second when necessary to maintain transfers with devices. Auto 1 or 2 Mbps The PC Card will adjust to the most suitable trans-
mission rate. The transmit data rate is either 1 Mbps or 2 Mbps. 11 Mbps Fix data rate to 11 megabits per second. 5.5 Mbps Fix data rate to 5.5 megabits per second. 2 Mbps Fix data rate to 2 megabits per second. 1 Mbps Fix data rate to 1 megabits per second. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 33 Chapter 3 - Reference PS Mode Use the PS Mode to control ASUS SpaceLink PC Cards power saving settings. Unchecking the checkbox will allow a full powered state that yields the best performance. This mode is recommended for devices running on AC power. Check the checkbox will enable power savings. The ASUS SpaceLink PC Card will wake up periodically to see if there is any data being sent. This mode is recommended for devices running on battery power. Others WEP Click on this to show the Encryption page. Advanced Click on this to show the Advanced tab. In most cases, the default values do not have to be changed. Troubleshooting Click on this to show the Troubleshooting utility. Click Apply to save and activate the new configurations. C h a p t e r 3 34 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.4.5 Config - Encryption Tab Lets you configure the ASUS SpaceLink PC Card encryption settings. For data confidentiality in a wireless environment, IEEE 802.11 specifies a Wired Equivalent Privacy (WEP) algorithm to offer transmission privacy similar to wired network. The WEP uses keys to encrypt transmitted data packets and decrypt received data packets. The encryption process can scramble frame bits to avoid disclosure to others. 3 r e t p a h C Data encryption (WEP enabled) This option allows you to enable or disable the Wired Equivalent Privacy
(WEP) function. If this check box is selected, a WEP Key is used to en-
crypt your data before it is transmitted over the air. If you enable WEP encryption, you will only be able to communicate with wireless devices that use the same WEP keys. WEP Key This option is enable only if you enable WEP Encryption. The WEP Key is a 64 bits (5 byte) or 128 bits (13 byte) Hexadecimal digits that is used to encrypt transmit data packets and decrypt received data packets. ASUS SpaceLink WL-100g WLAN PC Card 35 C h a p t e r 3 Chapter 3 - Reference Key Format You can enter the WEP Key as Hexadecimal digits (0~9, a~f, and A~F), or as ASCII characters, based on the state of the Key Format. Key Length For 64 bits encryption, each Key contains exactly 10 hex digits, or 5 ASCII characters. For 128 bits encryption, each Key contains exactly 26 hex dig-
its, or 13 ASCII characters. Two ways to assign WEP keys Manual Assignment When you click this button, the cursor appears in the field for Key 1. For 64-bit encryption, you are required to enter four WEP Keys. Each Key contains exactly 10 hex digits (0~9, a~f, and A~F). For 128-bit encryption, you are required to enter four WEP Keys. Each Key contains exactly 26 hex digits (0~9, a~f, and A~F). Automatic Generation Type a combination of up to 64 letters, numbers, or symbols in the Passphrase column, then the Wireless Settings Utility uses an algorithm to generate four WEP Keys for encryption. NOTE: This function eases users from having to remember their passwords and is compatible to some existing WLAN utilities, but this is not very secure. Manual Assignment is more secure. Default Key The Default Key field lets you specify which of the four encryption keys you wish to use to transmit data on your wireless LAN. You can change the default key by clicking on the down arrow at the right of this field, selecting the number of the key you want to use, and then clicking the Apply button. As long as the Access Point or station with which you are communicating has the same key in the same position, you can use any of the keys as the default. Click the Apply button to create your encryption keys. After you click the Apply button, the Wireless Settings utility uses asterisks to mask your keys. Click Apply to save and activate the new configurations. 36 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 64/128bits versus 40/104bits You may be confused about configuring WEP encryption, especially when using multiple wireless LAN products from different vendors. There are two levels of WEP Encryption: 64 bits and 128 bits. First, 64 bit WEP and 40 bit WEP are the same encryption method and can interoperate in the wireless network. This lower level of WEP encryption uses a 40 bit (10 Hex character) as a secret key (set by user), and a 24 bit Initialization Vector (not under user control). This together makes 64 bits (40 + 24). Some vendors refer to this level of WEP as 40 bits and others refer to this as 64 bits. ASUS SpaceLink products use the term 64 bits when referring to this lower level of encryption. Second, 104 bit WEP and 128 bit WEP are the same encryption method and can interoperate in the wireless network. This higher level of WEP encryption uses a 104 bit (26 Hex character) as a secret key (set by user), and a 24 bit Initialization Vector (not under user control). This together makes 128 bits (104 + 24). Some vendors refer to this level of WEP as 104 bits and others refer to this as 128 bits. ASUS SpaceLink products use the term 128 bits when referring to this higher level of encryption. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 37 Chapter 3 - Reference 3.4.6 Config - Advanced Tab Advanced tab provides some additional settings for the ASUS SpaceLink PC Card. The Advanced tab is hidden until you click Advanced on the Config - Basic page. C h a p t e r 3 NOTE: This page is for advanced users. Do not change these set-
tings if you do not fully understand these items. RTS Threshold Defines the size of packets that the station uses for RTS/CTS handshake boundary. Setting the minimum size packet too small causes RTS packets to be sent more often, adding excessive overhead to the network and de-
creasing network utilization. However, the more often RTS packets are sent, the more transmission collisions can be avoided. RTS threshold ranges from 0 to 2346 in 64 steps. Fragmentation Threshold Define the number of bytes used for fragmentation boundary. If the length of the data unit exceedsthis parameter , it will be divided into smaller frag-
ments for transmission. Each of the fragments is sent independently. If there is a significant interference present, set the fragment size smaller. Otherwise,set the fragment size lar ger. Because send multiple frames lead to overhead on the network.Fragmentation Threshold ranged from 256 to 2432 steps 128. 38 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference Authentication Algorithm Because there is no precise bound in wireless LANs, it needs to be imple-
mented in another mechanism to provide a higher level of security. That is where Authentication services come in. If a mutual authentication relation-
ship has not been established between the ASUS SpaceLink PC Card(s) and the Access Point(s), an association cannot be established. Auto based on WEP setting Switch the authentication mode based upon the ASUS SpaceLink PC Card using WEP encryption or not. Open System A null authentication algorithm. A station can authenticate with any other station or Access Point and without checking any WEP Key, even if one exists. Share Key In a Share Key Authentication system, four-step exchange of frames is required to validate that the station is using the same WEP Key as the Access Point. Using this Authentication mechanism requires imple-
mentation of the WEP option. Maximum Listen Interval This value is used to indicate how often a station will wake up to listen to beacon management frames. Listen intervals range from 0 to 77 in steps of 1. Preamble Mode This parameter is used to control whether frames will transmit with the long or short preamble. Click Apply to save and activate the new configurations. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 39 Chapter 3 - Reference 3.4.7 Survey - Site Survey Tab Use the Site Survey tab to view statistics on the wireless networks avail-
able to the ASUS SpaceLink PC Card. The Site Survey tab is read-only with no user configurable data fields. Use the Site Survey tab to view the following network parameters. BSSID View the IEEE MAC addresses of the available networks. SSID View the SSID (service set identification) within available networks. CH View the direct-sequence channel used by each network. S (dBm) Signal field to view the strength of the signal transmitted by each network. This information is helpful in determining which network you should be associated to. The value is then normalized to a dBm value. N (dBm) Noise field to view average noise level statistics and Rela-
tive Signal Strength Information (RSSI). This information is helpful in determining which network you should be associated to. The value is then normalized to a dBm value. Type View wireless network status information, the value is either AP (infrastructure) or STA (Ad Hoc). WEP View wireless network WEP encryption information, the value is either OFF (disable encryption) or ON (enable encryption). C h a p t e r 3 Some Access Points can disable broadcasting SSID to hide themselves from Site Survey or Site Monitor for added security but still allow you to join if you know their SSID. Buttons Search Scan all available wireless networks and show the scan result in the Available Network List. Connect To associate a network, select it from the Available Network List and click this button. 40 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.4.8 About - Version Info Tab Click about to view version information. The version under the copyright is the utility version. The version information field includes driver, hard-
ware, and firmware versions. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 41 Chapter 3 - Reference 3.4.9 Link Status ASUS SpaceLink PC Card connection quality icon appears on the left of the ASUS WLAN Card Settings. Use the icon to view the current signal quality of the adapter. Excellent Link Quality (Infrastructure) Good Link Quality (Infrastructure) Fair Link Quality (Infrastructure) Poor Link Quality (Infrastructure) C h a p t e r 3 Not linked (Infrastructure) Linked (Ad Hoc) Not Linked (Ad Hoc) To Exit Wireless Settings To exit Wireless Settings, you can click OK or Cancel. This utility may be closed at any time and from any tab. If you did not save the configuration settings, you will be prompted to do so. 42 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.5 Mobile Manager Mobile Manager is a convenient tool to setup and manage network loca-
tion settings. Mobile Manager lets users configure multiple alternative con-
figurations for different locations. You only need to set this once, and then easily switch configurations when you change your location. Starting Mobile Manager Click the Windows Start button, select Programs, select ASUS WLAN Card Utilities, and then click Mobile Manager. or Right-click the Control Center icon on the Windows taskbar and then click Mobile Manager. Using Mobile Manager - Quick Guide 1. The first time you launch the Mobile Manager utility, it will automati-
cally generate configurations that stores the current settings of all in-
stalled network devices in your system. 2. Change the name of the configuration to a descriptive name like Work-
3 r e t p a h C Meeting Room or Home-ADSL. 3. On the File menu, click New Configuration, the New Configuration Wizard dialog appears. Follow the on-screen instructions to create your own location configurations. 4. After you have created your configurations, you can see them in the main window. 5. Select the configuration you want to use and then click Mobilize Con-
figuration from the Mobilize pull-down menu. Your system will then switch to the network settings configured to your chosen selection. ASUS SpaceLink WL-100g WLAN PC Card 43 Chapter 3 - Reference 3.5.1 Main Window You can use the Mobile Manager utility main window to create a new configura-
tion, edit a configuration or activate a configuration. The main window includes a menu bar, tool bar, and a list view for showing existing configurations. C h a p t e r 3 Using the pull-down menu and toolbar The following topics show the commands available from the Mobile Manager pull-down menu and toolbar. If no configuration is selected, some commands will be grayed out and inaccessible. The toolbar contains buttons for many of the most commonly used commands in Mobile Manager. It allows quick ac-
cess to some of the most useful features of Mobile Manager. The commands provided by the toolbar buttons are also available from the pull-down menu. File Menu New Configuration - Select New Configuration in the File menu to open a New Configuration Wizard dialog. Use the New Configu-
ration Wizard dialog to create a new configuration. See Using New Configuration Wizard for details on this command. Import Configuration - Load a configuration from an INI File. Export Configuration - Save the selected configuration (contain-
ing Wireless Settings, TCP/IP Settings, Network Settings, ...) to an INI File. The INI file can be placed on a floppy diskette and then imported by other computers using Mobile Manager. This can also be used as a backup feature for yourself. Exit - Close the Mobile Manager utility. 44 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference Mobilize Menu Auto Roaming If an association changes, it will automatically switch into a network configuration that you have made. If no asso-
ciations have been made, it will automatically connect to a wireless network based on configurations that you specify. Activate Configuration Applies the configuration that you have selected from the list. You may be prompted to restart Windows depending on the required changes. Follow the instructions on the screen. Windows 2000 and XP usually do not require restarting your computer, but Windows 98 and ME usually will require a restart. Edit Menu All these commands are also available from the context menu that appears when you right-click with a configuration in the Mobile Manager window. Edit Configuration - Select Edit Configuration in the Edit menu to open an Edit Configuration dialog to edit selected configuration items. See Using Edit Configuration for details on this command. Rename - Change the name of the selected configuration. 3 r e t p a h C Copy - Duplicate the selected configuration. Delete - Discard the selected configuration. View Menu Large Icons - Displays large icons for each configuration. Small Icons - Displays small icons for each configuration. List - Shows the configuration names in a list. Details - The Detailed view expands this list to include information about the configurations. The information includes configuration name, type, and description. ASUS SpaceLink WL-100g WLAN PC Card 45 Chapter 3 - Reference Help Menu Contents - Displays the WinHelp contents window (the one you are reading now) for online Help. About Mobile Manager - Displays the version number and copy-
right information for Mobile Manager. Click on the logo to connect to ASUS website. C h a p t e r 3 46 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.5.2 Using New Configuration Wizard Create a new configuration Create a new configuration if you are in a specific location that does not have an existing configuration defined. Use the New Configuration Wiz-
ard to create a configuration in a few easy steps. 1. Do one of the following:
On the File menu, click New Configuration. or Double-click New Configuration on the Main window. Then the New Configuration Wizard dialog starts. 2. Choose the type of configuration that you want to create and click Next. Wireless Local Area Network Configuration: You must have an ASUS SpaceLink PC Card installed in your PC. Wired Local Area Network Configuration: You must have a NIC (LAN card) (other than ASUS SpaceLink PC Card) installed in your PC. Dialup Networking Configuration: You must have a modem in-
stalled in your PC. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 47 C h a p t e r 3 Chapter 3 - Reference 3. Enter the name and description you want to use for this configuration in the Name and description field. And Click Next. 4. Follow the on-screen instructions, it will guide you through the process of specifying the settings in your configuration. The Wizard reads the current system settings (TCP/IP, NT Domain, Proxy, File, and Printer Sharing) and displays it. Depending on the configuration that you have created, you can set the following groups of settings:
Wireless settings (for Wireless Configuration) Network settings (for Wireless/Wired Configuration) TCP/IP settings (for Wireless/Wired Configuration) Dialing settings (for Dialup Configuration) Dialup Networking settings (for Dialup Configuration) Internet settings (for Wireless/Wired/Dialup Configuration) Sharing settings (for Wireless/Wired/Dialup Configuration) See Using Edit Configuration for detailed information on each. 5. Enter the appropriate information in the wizard. After specifying the appropriate information on each page, click Next to continue. 6. On the final window of the New Configuration Wizard, you will see a Finish button. If you do not want to use this new configuration now, click Finish to save the new configuration. It will be shown in the Mobile Man-
ager main window. or If you want to use this new configuration now, click Mobilize. 3.5.3 Using Edit Configuration Edit an existing configuration Edit a configuration if you want to view or change dialup or LAN settings. On the Edit menu, click Edit Configuration. or Double-click one existing configuration on the Main window. Then the Edit Configuration dialog starts. The Edit Configuration dialog contains various settings, which you select by clicking the buttons at the left of the window. Each setting is described below. 48 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference General settings Name This field is mandatory, and used for indicating the location from which you are dialing or connecting to the network. For example, if this is used for a meeting room at work, you can use a name like Work-Meeting Room. If it is used for home on your ADSL, you can name like Home-ADSL. Description This field is optional, you can use it to provide more details about this configuration. Network settings Network settings include: Identification and Microsoft Networking. Identification Computer name Give your computer a unique name of up to 15 characters. Thecomputer name is the name that others on your net-
work will see your computer as. For complete compatibility, do not use spaces or symbols. Its generally the same as the DNS hostname, for example, JohnDoe. Workgroup Type an existing workgroup name or create a new workgroup by typing a new name that contains up to 15 characters. Use it to identify your computer group that you belong to. Computer Description This information is displayed as a comment next to the computer name when the computer is seen in Details view
(select from the Windows pull-down menu). Use it to describe your computer, for example, your name, or location. 3 r e t p a h C Microsoft Networking Logon validation Specify how Windows 9x clients connect to a Win-
dows NT Server Domain at this location.Check Log on to Windows NT domain box if you are using a Windows NT Server in domain control-
ler mode. And then enter the Window NT server domain name in Win-
dow NT domain field. Network logon options Specify how Windows 9x clients try to logon. Select Quick logon to wait until the shared network drives is actually used to attempt the login. Select Logon and restore network connections to logon to all shared network drives when the user logs into Windows. ASUS SpaceLink WL-100g WLAN PC Card 49 C h a p t e r 3 Chapter 3 - Reference Wireless settings Network Type Infrastructure Select the Infrastructure mode to establish a connec-
tion with an Access Point. Ad Hoc Select the Ad Hoc mode to communicate directly with each other without using an Access Point. SSID Using the SSID filed to configure the SSID setting for the ASUS SpaceLink PC Card. SSID stands for Service Set Identifier, which is a string used to identify a wireless LAN. You will only be able to connect with an Access Point, which has the same SSID. Use different SSIDs to segment the wire-
less LAN and add security. Note that the SSID must be all printable character string (case sensitivity) and up to 32 characters long, such as WIRELESS LAN. Set the SSID to any if you wish to allow your station to connect to any IEEE 802.11 Infrastructure Network it can find. Channel Using the Channel filed to select the radio channel for PC Card. In infra-
structure network, your PC Card will automatically select the correct fre-
quency channel required to communicate with an Access Point, this param-
eter will be fixed in Auto and cant change it. In an Ad Hoc Network, you can decide channel number for the PC Card to operate. PC Cards can com-
municate in the network if each has the same frequency channel setting. Data Rate Fully Auto Automatic transmit data rate fallback to 1, 2, 5.5, or 11 megabits per second for communication with other devices. Auto 1 or 2 Mbps The ASUS SpaceLink PC Card will use the most suitable transmission rate of either 1 Mbps or 2 Mbps. 11 Mbps Fix transmit data rate to 11 megabits per second. 5.5 Mbps Fix transmit data rate to 5.5 megabits per second. 2 Mbps Fix transmit data rate to 2 megabits per second. 1 Mbps Fix transmit data rate to 1 megabits per second. 50 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference WEP Select disable or enable (64-bit or 128-bit) WEP encryption. The WEP Key is a 64-bit (5 byte) or 128-bit (13 byte) Hexadecimal digit that is used to encrypt transmit data packets and decrypt received data packets. TCP/IP settings TCP/IP settings include five tabs: Device, IP Address, Gateway, DNS, and WINS. Device Choose the network adapter that you want to use for this configuration. IP Address Obtain an IP address from a DHCP server Dynamic host configu-
ration protocol (DHCP) server assigns IP addresses automatically within a specified range to devices. Specify an IP address Ask your network administrator for the IP address and subnet mask that you should use. Type in the IP Address and Subnet Mask fields manually. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 51 C h a p t e r 3 Chapter 3 - Reference Gateway Specify the gateways. There can be more than one specified.Set up the primary gateway first. Add a gateway - Type the IP address of the gateway in the New Gate-
way field and then click Add. The gateway you specified appears in the Installed Gateways list. Repeat to specify another gateways. The value in each field must be a number between 0 and 255. You can have up to eight IP addresses for gateways. Remove a gateway - Select the gateway from the Installed Gateways list and click Remove. DNS Select Enable or Disable DNS. If you enable DNS, fill the following pa-
rameters. Host Enter the name of your computer. That is used to identifier the computer on the Internet. The hostname is generally the same as the Microsoft networking computer name, for example, S82000W. Domain Enter the TCP/IP domain name for your network.The full domain name consists of one or more names that are separated by dots, for example, asus.com. DNS Server Search Order Specify the DNS Servers in the desired order to search for DNS information. Domain Suffix Search Order Add any domain suffixes that may be valid attached to the end of Internet domain name. WINS Specify the WINS server. There can be more than one specified.Set up the primary WINS server first. Disable WINS Resolution Do not use WINS resolution. Enable WINS Resolution Use WINS resolution. Specify the IP ad-
dresses of the WINS servers in the desired search order. Scope ID is used when NetBIOS over TCP/IP is enabling on the workstations. If this protocol has been enabled, then every workstation group must have the same Scope ID for those computers to communicate within the group. The Scope ID is usually left blank. Use DHCP for WINS Resolution If a DHCP server is available that is configured to provide information on available WINS servers. 52 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference Dialing settings Specify how the call will be dialed. This is useful if you want to change the call to a calling card, use your computer from different locations, or add a dial prefix, country code, or area code automatically. Dialup Networking settings Dialup Networking settings include four tabs: Device, Phone Number, Server Type, and TCP/IP. Device Choose the modem you want to use by Dial-Up Networking to connect to another computer for this connection. Phone Number Specify area code, telephone number, and country code for this connec-
tion. Clear the Use area code and Dialing Properties checkbox, if you want to ignore area code and dialing settings. Server Type Type of Dial-Up Server Select the server type for this connection. Advanced options Select Log on to network checkbox to specify that Dial-Up Networking will attempt to log on to the network you are connecting to, using the user name and password you typed when you logged on to Windows. Select Enable software compression checkbox to specify whether incom-
ing or outgoing information is compressed before it is sent. This is useful to speed up the transfer of information. Compression occurs only if both computers are using compatible compression. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 53 C h a p t e r 3 Chapter 3 - Reference Select Require encrypted password checkbox to specify that only en-
crypted passwords can be sent to or accepted by your computer. This is useful if you need additional security for this connection. When type your password while dialing out, this setting will encrypt your password but the target computer must support encrypted passwords for your password to be understood. Allowed network protocols Specifies the network protocols that your computer can use. Select NetBEUI protocol to connect to Windows NT, Windows for Workgroups, or LAN Manager servers. Select IPX/SPX Compatible protocol to connect to Netware and Win-
dows NT servers and Windows 98 computers. Select TCP/IP protocol to connect to Internet and wide-area networks. TCP/IP Server assigned IP address Specifies whether Dialup Networking accepts an IP address from a ppp server. If the ppp server does not offer an IP address, the IP address specified for TCP/IP Dial-Up Adapter in the Network dialog box is used. Specify an IP address Provides a space for you to type the preferred IP address for this connection. Dial-Up Networking tries to use this address first. Server assigned name server addresses Specifies whether Dial-Up Networking accepts a DNS and WINS server addresses from a ppp server. If the ppp server does not offer DNS and WINS addresses, DNS and WINS server addresses specified for TCP/IP Dial-Up Adapter in the Network dialog box are used. Specify name server addresses Provides a space for you to type one or two DNS and WINS server addresses for this connection only. Dial-
Up Networking tries to use these addresses first. Use IP header compression Specifies whether Dial-Up Networking uses IP header compression for this connection. IP header compression optimizes data transfer between computers. Use default gateway on remote network Specifies whether IP traf-
fic is routed to the WAN connection by default. 54 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference Internet settings A proxy server acts as a security barrier between your internal network
(Intranet) and the Internet, keeping other people on the Internet from gain-
ing access to confidential information on your internal network or your computer. Disable Proxy Server Do not use proxy server. Enable Proxy Server Use the Proxy server to gain access to the Internet. Use the same proxy server for all protocols Specifies whether you want to use the same proxy server to gain access to the Internet using all protocols. Servers Provides spaces for you to type the address and port number of the proxy server you want to use to gain access to the Internet over HTTP, Secure, FTP, Gopher, and Socks protocol. Exceptions Do not use proxy server for address beginning with Provides a space for you to type the Web addresses that do not need to be accessed through the proxy server. If you want to connect to a computer on your Intranet, make sure you type its address in this box. You can use wild cards to match domain and host names or addresses, for example, *.company.com, 192.72.111.*. Bypass proxy server for local addresses Specifies whether you want to use the proxy server for all local (Intranet) addresses. You might be able to gain access to local addresses easier and faster if you do not use the proxy server. Sharing settings I want to be able to give others access to my files Turn file sharing ON or OFF. File sharing enables people using other computers to read or modify files you share on your computer. I want to be able to allow others to print to my printer(s) Turn printer sharing ON or OFF. Printer sharing enables people using other computers to printer their files on your printers. Click Save button to save all the changes you have made without clos-
ing the Edit Configuration dialog box. Click Cancel button to close the Edit Configuration dialog box without saving any changes you have made. Click Close button to close the Edit Configuration dialog box and save any changes that you have made. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 55 Chapter 3 - Reference 3.6 Site Monitor Site Monitor measures the signal-to-noise (SNR) values of all available wireless networks. This tool is used for determining the best placement of Access Points to provide the best coverage for a wireless network. 3.6.1 Starting Site Monitor Click the Windows Start button, select Programs, select ASUS WLAN Card Utilities, and then click Site Monitor. or Right-click the Control Center icon on the Windows taskbar and then click Site Monitor. C h a p t e r 3 3.6.2 Main Screen Measures the signal-to-noise (SNR) values of all available wireless net-
works. Some Access Points can disable broadcasting SSID to hide them-
selves from Site Survey or Site Monitor for added security but still allow you to join if you know their SSID. 56 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3.6.3 Monitor Directed link state test with one wireless network, including:
SNR: This indicates the quality of communications within the current network. The communication quality is based on signal level and noise level measurements. In principle, the higher the SNR, the better your communications quality. Communication Quality: Specifies the Communication Quality of the Basic Service Set to which the station is currently connected to. Signal Level: Specifies the Average Signal Level of the Basic Service Set to which the station is currently connected to. Noise Level: Specifies the Average Noise Level of the Frequency Chan-
nel currently used for communications. Throughput: This sends a specified number of data packets to the re-
mote host and calculates the average megabytes per second. During the test, the Start button toggles to Stop. You can click Start button to begin the link test and click Stop button at any time to terminate the test. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 57 Chapter 3 - Reference 3.7 Live Update Live Update is a utility that allows you to update your ASUS SpaceLink PC Cards firmware and drivers. The use of this utility assumes that you are properly connected to Internet through an Internet Service Provide (ISP). 1. Insert the ASUS SpaceLink PC Card Support CD into your CD-ROM drive to bring up the autorun menu. If the autorun menu does not show, double-click the CD drive icon in My Computer or run Setup.exe in the root directory of your CD-ROM drive. When the Main menu appears, click Run Live Update. 2. Select an update method from the pull-down menu. C h a p t e r 3 Update Firmware/Driver from the Internet: Lets you update the ASUS SpaceLink PC Cards firmware or driver from the Internet. The updating (running the flash utility or the installation program) will be done automatically. Update Firmware/Driver from the Disk: Lets you specify the update firmware or driver file from a disk. The updating (running the flash utility or the installation program) will be done automatically. Download Firmware/Driver from the Internet: Lets you download the firmware or driver to a disk on your computer for manual updating later. 58 ASUS SpaceLink WL-100g WLAN PC Card Chapter 3 - Reference 3. Follow any on-screen instructions or prompts to complete setup. If you already have the latest revision of your ASUS SpaceLink PC Cards firmware files or driver files, Live Update reports that no update is necessary. When Live Update starts the firmware upgrade, a warning message will tell you that incorrect firmware upgrades may cause your ASUS SpaceLink PC Card to malfunction. You can cancel the update process at this point. If you continue, a message will tell you that the update process has started. Do not turn OFF your computer until the upgrade has completed. The upgrade will take approximately 30 sec-
onds. A subsequent message states whether the update was successful. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 59 Chapter 3 - Reference 3.8 Windows XP Wireless Properties 1. Double-click System icon in the Control Panel. 2. Double-click ASUS SpaceLink WL-
100g... C h a p t e r 3 3. The General page will show status, duration, speed, and signal strength. Signal strength is represented by green bars with 5 bars meaning excellent signal and 1 bar meaning poor signal. 4. The Wireless Networks page will show Available networks and Preferred networks. Use the Add button to add the SSID of available networks and set the connection preference order with the Move up and Move down buttons. The radio tower with a signal icon identifies the currently connected access point. 60 ASUS SpaceLink WL-100g WLAN PC Card 3.8 Windows XP Wireless Properties (Cont.) Chapter 3 - Reference 5. The Authentication page allows you to 6. The Advanced page allows you to set add security settings. Read Windows help for more information. firewall and sharing. Read Windows help for more information. 3 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 61 Chapter 3 - Reference C h a p t e r 3 62 ASUS SpaceLink WL-100g WLAN PC Card Chapter 4 - Troubleshooting 4. Troubleshooting The below troubleshooting guides provide answers to some of the more common problems, which you may encounter while installing or using ASUS SpaceLink PC Card products. If you encounter difficulties that are not mentioned in this section, please contact ASUS Wireless LAN Techni-
cal Support. Verify if the PC Card is installed correctly. When the ASUS SpaceLink PC Card setup task is complete, you can verify if the driver has been setup properly. Right click My Computer, select Properties, and click the Device Manager tab. Then double-click the Net-
work adapters icon; you should see ASUS SpaceLink WL-100G WLAN PC Card with an icon of expansion card. There should not be a ! or ?
(problem) or x (disabled) symbol over this icon. There is a yellow exclamation mark or a yellow question mark in Device Manager in front of my ASUS SpaceLink PC Card. To resolve the problem, you should update/reinstall the ASUS SpaceLink PC Card driver. In Device Manager, right click ASUS SpaceLink WL-
WL-100g WLAN PC Card, select Properties, and select Driver tab. Click on Update Driver button, then follow the Update Device Driver Wizard to complete the driver installation. In addition, you may be able to resolve this issue by reinstalling the driver. Choose ASUS SpaceLink WL-100G WLAN PC Card, click Remove button in Device Manager, and then run the Add New Hardware Wiz-
ard from the Control Panel. Cannot connect to any Access Points Follow the procedure below to configure your ASUS SpaceLink PC Card. a. Verify that the Network Type is in Infrastructure mode. b. Verify that the SSID of your ASUS SpaceLink PC Card is set to any or set to the same SSID of an Access Point. c. Verify that the Encryption type is the same as that of an Access Point. If you enabled WEP encryption, you must also set the same WEP Keys on both sides. 4 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 63 Chapter 4 - Troubleshooting Cannot connect to a Station (ASUS SpaceLink PC Card) Follow the procedure below to configure your ASUS SpaceLink PC Card. a. Verify that the Network Type is in Ad Hoc mode. b. Verify that the SSID of your ASUS SpaceLink PC Card is set to any or set to the same SSID of the other station (or another ASUS SpaceLink PC Card). c. Verify that the channel of the ASUS SpaceLink PC Card is Auto or set to the same channel of the other station (or another ASUS SpaceLink PC Card). d. Verify that the Encryption type is the same as the other station (or another ASUS SpaceLink PC Card). If WEP encryption is enabled, you must set the same WEP Keys on both stations. Bad link quality or bad signal strength There are two possible reasons. First is radio interference, keep the envi-
ronment around the ASUS SpaceLink PC Card away from microwave ov-
ens and large metal objects. Then try to reorient the ASUS SpaceLink PC Card antenna. Second is the distance, decrease the distance between your ASUS SpaceLink PC Card and the Access Point or station (or another ASUS SpaceLink PC Card). The TCP/IP protocol did not bind to the SpaceLink PC Card. This will occur when the computer already has six TCP/IP bindings in Windows 98 or ten bindings in Windows Me. These limits are imposed by the Microsoft operating system. C h a p t e r 4 Solution: If your computer already has the maximum number of TCP/IP bindings, remove one of the network adapters from the Network configu-
ration before installing the ASUS SpaceLink PC Card driver. In Ad Hoc network mode, I have connected to a station but my ASUS SpaceLink PC Card cannot get an IP address. Windows Me/2K/XP contains the Media Sensing feature, which can de-
tect a disconnect state on the media, it removes the bound protocols from that adapter until it has detected a link. But in Ad Hoc mode, it will errone-
ously detect the media as being disconnected. Solution: (1) Run Wireless Settings (2) click Config (3) uncheck Detect connection to network media (4) click Apply (5) restart your computer 64 ASUS SpaceLink WL-100g WLAN PC Card Chapter 5 - Glossary 5. Glossary Access Point (AP) An networking device that seamlessly connects wired and wireless net-
works. Access Points combined with a distributed system support the cre-
ation of multiple radio cells that enable roaming throughout a facility. Ad Hoc A wireless network composed solely of stations within mutual communi-
cation range of each other (no Access Point). Basic Service Area (BSS) A set of stations controlled by a single coordination function. Channel An instance of medium use for the purpose of passing protocol data units that may be used simultaneously, in the same volume of space, with other instances of medium use (on other channels) by other instances of the same physical layer, with an acceptably low frame error ratio due to mutual in-
terference. Extended Service Set (ESS) A set of one or more interconnected basic service set (BSSs) and integrated local area networks (LANs) can be configured as an Extended Service Set. Ethernet The most widely used LAN access method, which is defined by the IEEE 802.3 standard. Ethernet is normally a shared media LAN meaning all de-
vices on the network segment share total bandwidth. Ethernet networks operate at 10Mbps using CSMA/CD to run over 10-BaseT cables. Gateway A network component that acts as an entrance to another network. 4 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 65 Chapter 5 - Glossary IEEE 802.11 IEEE 802.xx is a set of specifications for LANs from the Institute of Elec-
trical and Electronic Engineers (IEEE). Most wired networks conform to 802.3, the specification for CSMA/CD based Ethernet networks or 802.5, the specification for token ring networks. 802.11 defines the standard for wireless LANs encompassing three incompatible (non-interoperable) tech-
nologies: Frequency Hopping Spread Spectrum (FHSS), Direct Sequence Spread Spectrum (DSSS), and Infrared. 802.11 specifies a carrier sense media access control and physical layer specifications for 1 and 2 Mbps wireless LANs. IEEE 802.11b 802.11b specifies a carrier sense media access control and physical layer specifications for 5.5 and 11 Mbps wireless LANs. Infrastructure A wireless network centered about an access point. In this environment, the access point not only provides communication with the wired network but also mediates wireless network traffic in the immediate neighborhood. IP (Internet Protocol) The TCP/IP standard protocol that defines the IP datagram as the unit of information passed across an Internet and provides the basis for connectionless packet delivery service. IP includes the ICMP control and error message protocol as an integral part. It provides the functional equiva-
lent of ISO OSI Network Services. IP Address An IP address is a 32-bit number that identifies each sender or receiver of information that is sent across the Internet. An IP address has two parts: the identifier of a particular network on the Internet and an identifier of the particular device (which can be a server or a workstation) within that net-
work. C h a p t e r 5 ISM Bands (Industrial, Scientific, and Medicine Bands) Radio frequency bands that the Federal Communications Commission
(FCC) authorized for wireless LANs. The ISM bands are located at 902 MHz, 2.400 GHz, and 5.7 GHz. 66 ASUS SpaceLink WL-100g WLAN PC Card Chapter 5 - Glossary ISP (Internet Service Provider) An organization that provides access to the Internet. Small ISPs provide service via modem and ISDN while the larger ones also offer private line hookups (T1, fractional T1, etc.). LAN (Local Area Network) A communications network that serves users within a defined geographi-
cal area. The benefits include the sharing of Internet access, files and equip-
ment like printers and storage devices. Special network cabling (10 BaseT) is often used to connect the PCs together. NIC (Network Interface Card) A network adapter inserted into a computer so that the computer can be connected to a network. It is responsible for converting data from stored in the computer to the form transmitted or received. Packet A basic message unit for communication across a network. A packet usu-
ally includes routing information, data, and sometimes error detection in-
formation. PCMCIA (Personal Computer Memory Card International Association) The Personal Computer Memory Card International Association (PCMCIA), develops standards for PC cards, formerly known as PCMCIA cards. These cards are available in three types, and are have about the same length and width as credit cards. However, the different width of the cards ranges in thickness from 3.3 mm (Type I) to 5.0 mm (Type II) to 10.5 mm (Type III). These cards can be used for various functions, including memory storage, landline modems and wireless modems. Radio Frequency (RF) Terms: GHz, MHz, Hz The international unit for measuring frequency is Hertz (Hz), equivalent to the older unit of cycles per second. One megahertz (MHz) is one million Hertz. One gigahertz (GHz) is one billion Hertz. The standard US electri-
cal power frequency is 60 Hz, the AM broadcast radio frequency band is 0.55-1.6 MHz, the FM broadcast radio frequency band is 88-108 MHz, and wireless 802.11 LANs operate at 2.4 GHz. 4 r e t p a h C ASUS SpaceLink WL-100g WLAN PC Card 67 Chapter 5 - Glossary SSID (Service Set ID) SSID is a group name shared by every member of a wireless network. Only client PCs with the same SSID are allowed to establish a connection. Station Any device containing IEEE 802.11 wireless medium access conformity. TCP (Transmission Control Protocol) The standard transport level protocol that provides the full duplex, stream service on which many application protocols depend. TCP allows a pro-
cess or one machine to send a stream of data to a process on another. Soft-
ware implementing TCP usually resides in the operating system and uses the IP to transmit information across the network. C h a p t e r 5 68 ASUS SpaceLink WL-100g WLAN PC Card
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2003-06-10 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2003-06-10
|
||||
1 | Applicant's complete, legal business name |
ASUSTeK Computer Inc
|
||||
1 | FCC Registration Number (FRN) |
0005821988
|
||||
1 | Physical Address |
4F, No. 150, Li-Te Rd.
|
||||
1 |
Peitou, Taipei, N/A 112
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@americanTCB.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
MSQ
|
||||
1 | Equipment Product Code |
WL-100G
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J**** Y****
|
||||
1 | Title |
Associate Vice President
|
||||
1 | Telephone Number |
+886-********
|
||||
1 | Fax Number |
+886-********
|
||||
1 |
j******@asus.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation
|
||||
1 | Name |
E****** W****
|
||||
1 | Physical Address |
13-1, Lane 19, WenShan 3rd St
|
||||
1 |
Taiyuan, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
+886 ******** Extension:
|
||||
1 | Fax Number |
+886 ********
|
||||
1 |
e******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 802.11g Wireless PCMCIA Card | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power Output listed is Conducted. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with specific operating instructions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
R**** C********
|
||||
1 | Telephone Number |
886-2********
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CE | 2412.00000000 | 2462.00000000 | 0.0130000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC