WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6226995.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Quick Start Guide RP-AX58 AX3000 Dual-Band WiFi Range Extender LED Explanations WiFi Range Extender Mode Status Booting up LED Behavior Blinking White Booting up complete (not connected to Router) Solid Blue Reset (use a pin to press the reset button for 5 seconds) Blinking Yellow Rescue mode Starting WPS Connected to the router with Good Signal Connected to the router with Weak Signal No Signal Solid Purple Blinking Blue Solid White Solid Yellow Solid Red AP mode (with wired connection) Solid White AP mode (without wired connection) Solid Red BEFORE SETUP WE SUGGEST Hardware Explanations 1 Plug RP-AX58 into a power outlet. 2 The LED will start breathing white for 3 seconds while booting up. Button Explanations WPS BUTTON Launch the WPS Wizard. RESET BUTTON Reset the system to its factory default settings. LAN PORT Connect your PC to the LAN port with a network cable. LED WPS button reset button LAN port AiMesh Mode Status Booting up LED Behavior Blinking White Booting up complete (not connected to AiMesh Router) Solid Blue Reset (use a pin to press the reset button for 5 seconds) Rescue mode Blinking Yellow Solid Purple Connecting to the AiMesh Router Blinking Blue Connected to the AiMesh Router with Good Signal Solid White Connected to the AiMesh Router with Weak Signal Solid Yellow No Signal Ethernet backhaul Solid Red Solid White 01 Placing your RP-AX58 1 Plug your RP-AX58 into a power outlet near your router/AP. Check the LEDs and see the LED explanations. 2 Wait for the LED to flash and turn solid blue, 3 indicating that your RP-AX58 is ready to connect to your existing router/AP. around 2 meters NOTES:
To minimize interference, keep the routers away from devices like cordless phones, Bluetooth devices and microwave ovens. We recommend that you place the routers in an open or spacious location. SETUP METHODS Set up RP-AX58 as a WiFi range extender If you would like to connect RP-AX58 to other WiFi networks excluding AiMesh-supported routers, please download the ASUS Extender App or set up with the WPS button. METHOD 1 METHOD 2 Download the ASUS Extender App and follow the onscreen instructions Connect via WPS 1 Press the WPS button on your router/
AP. 2 Press the WPS button on your RP-AX58 for more than two (2) seconds until the LED starts to blink blue. SETUP METHODS Set up RP-AX58 as an AiMesh Node If you already have an AiMesh router and you are going to create an AiMesh system, please download and install ASUS Router App for RP-AX58 setup. STEPS 1 Download the ASUS Router App. 2 3 Follow the onscreen instructions to set up your AiMesh router. Tap and select Add AiMesh node. 4 Select RP-AX58 and follow the onscreen instructions to complete the setup. iv. After the firmware is uploaded, please go to the Network Map page to check and make sure that the AiMesh icon shows up. v. Use a pin to press the reset button on your RP-AX58 for at least 5 seconds. Release the reset button when the power LED is flashing slowly. TROUBLE SHOOTING If your AiMesh router cannot find RP-AX58 nearby or synchronization fails, please check followings and try again. a Plug RP-AX58 into a power outlet near your router/AP. Ensure that it is within 3 meters from the AiMesh router. b Your AiMesh router is upgraded to AiMesh-
supported firmware. c i. Download AiMesh - supported fireware at:
https://www.asus.com/AiMesh/. ii. Launch a web GUI. You will be redirected to the ASUS Setup Wizard. If not, navigate to http://www. asusrouter.com. iii. Go to Administration > Firmware Upgrade. Click Choose File, and upload the AiMesh-supported firmware. FAQ FREQUENTLY ASKED QUESTIONS Q1 Could I setup wired connection between AiMesh routers and nodes (Ethernet backhaul)?
A: Yes. AiMesh system supports both wireless and wired connection between an AiMesh router and node to maximize throughput and stability. AiMesh analyzes the wireless signal strength for each frequency band available, and then determines automatically whether a wireless or wired connection is best to serve as the inter-router connection backbone. 1 Follow the setup steps to establish a connection between the AiMesh router and RP-AX58 via WiFi first. 2 Place the RP-AX58 in an ideal location for the best coverage. Run an Ethernet cable from the LAN port of the AiMesh router to the Ethernet backhaul port of RP-
AX58. 3 AiMesh system will auto-select the best path for data transmission, whether wired or wireless. LAN to LAN (Ethernet backhaul) port ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions. REACH Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital de-
vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Frequency (RF) Exposure Information The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This equipment should be installed and operated with a minimum distance of 25 cm between the radiator any part of your body. This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development Canadas REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html Additional Canadian information on RF exposure also can be found at the following web:
https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Dclaration de conformit de Innovation, Sciences et Dveloppement conomique Canada (ISED) Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. La bande 5150 5250 MHz est rserve uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. CAN ICES-003(B)/NMB-003(B) Informations concernant lexposition aux frquences radio (RF) La puissance de sortie mise par cet appareil sans fil est infrieure la limite d'exposition aux frquences radio d'Innovation, Sciences et Dveloppement conomique du Canada
(ISED). Utilisez l'appareil sans fil de faon minimiser les contacts humains lors d'un fonctionnement normal. Cet quipement doit tre install et utilis avec un minimum de 25 cm de distance entre la source de rayonnement et votre corps. L'utilisation de cet appareil est autorise au Canada. Pour consulter l'entre correspondant l'appareil dans la liste d'quipement radio (REL - Radio Equipment List) d'Innovation, Sciences et Dveloppement conomique du Canada, rendez-vous sur :
http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html Pour des informations supplmentaires concernant l'exposition aux frquences radio au Canada, rendez-vous sur : https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html For product available in the US/Canada market, only channel 1~11 can be operated. Selec-
tion of other channels is not possible. Pour les produits disponibles aux tats-Unis et au Canada, seuls les canaux 1 11 peuvent tre utiliss. La slection dautres canaux nest pas possible. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Safety Notices Use this product in environments with ambient temperatures between 0C(32F) and 40C(104F). Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating. DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged. DO NOT place or drop objects on top and do not shove any foreign objects into the product. DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms. DO NOT cover the vents on the product to prevent the system from getting overheated. DO NOT use damaged power cords, accessories, or other peripherals. If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service techni-
cian or your retailer. To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. To know more about ASUS AiMesh, please go to https://www.asus.com/AiMesh/. Q2 How to set up the Access Point(AP) mode on an ASUS WiFi Range Extender?
1 Launch a web browser and enter http://www.asusrouter.com. 2 If you are logging into the Web GUI for the first time, you will be automatically directed to the Quick Internet Setup (QIS) page. Click Advanced Settings. 3 Click Choose operation mode, then click Access Point(AP) mode. 4 Click Automatic IP, then click to set up the SSIDs separately. 5 For the first time, youll need to set up the username and password for your RP-
AX58. When typing is done, click Next. Access Point(AP) mode setting is finished. WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device is restricted for indoor use. Prohibition of Co-location This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual. WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 44 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. CAN ICES-003(B)/NMB-003(B)