Users Manual ASUS BT-180 1 Contents Notice ............................................................................................ 3 Safety statements .............................................................................. 4 System requirements......................................................................... 6 Installing the device drivers......................................................... 6 BT-183 specification summary..................................... ............... 8 2 Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION! You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the Federal Register, National Archives and Records Administration, U.S. Government Printing Office. 3 Safety statements Regulatory Information/Disclaimers Installation and use of this Bluetooth device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. CAUTION! To maintain compliance with FCCs RF exposure guidelines, this equipment should be installed and operated with minimum distance [20cm]
between the radiator and your body. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. Safety Information In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance [20cm]
between the radiator and your body. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. CAUTION! Any changes or modifications not expressly approved in this manual could void your authorization to use this device. MPE Statement Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. FCC Radio Frequency Exposure This Bluetooth device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation output power of this Bluetooth device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation as a mobile or portable device but use in 4 a body-worn way is strictly prohibit. When using this device, a certain separation distance between antenna and nearby persons has to be kept to ensure RF exposure compliance. In order to comply with the RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than [20cm]. RF Exposure The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. About this guide This user guide contains the information your ASUS Bluetooth Module. 5 System requirements Before installing the ASUS Bluetooth module, make sure that your system meets the following requirements:
Intel Pentium 4 or AMD K7/K8 system Minimum 64MB system memory Windows 98SE/ME/2000/XP operating system Optical drive (for software installation) An available USB port (USB 2.0 recommended because USB 1.1 cannot achieve maximum wireless performance) Installing the device drivers To install the device driver in your computer:
Insert the support CD to the optical drive and follow the following procedure. 6 7 BT-180 specification summary i. Fully qualified Bluetooth v2.0 system ii. Enhanced Data Rate (EDR) compliant for both 2Mbps and 3Mbps supported iii. Fully speed operation with Piconet and Scatternet support iv. Electrical compliant to USB1.1&2.0 through proprietary Pin Connector (Note: Vcc is 3.3V, 5V is not allowed) v. Implement 802.11 coexistence solution by AFH (Adjacent Frequency Hopping), WCS (Wireless Coexistence System), and Bluetooth Priority vi. Slim module with 35*11 mm dimension vii. Chip Antenna and RF connector are manufacturing optional for different application viii. All components on single side of PCB ix. Antenna matching could be fine tuned if mechanism is changed 8