FCC ID: 2AQ8P-ILR1 Radio module for indoor asset localization systems

IL-R V1 Safety Information Printed Matter No. 9839 1630 00 Publication Date 2019-06-28 Valid from Serial No. -

Industrial Location Radio Module WARNING To reduce risk of injury, everyone using, installing, repairing, main-

taining, changing accessories on, or working near this tool MUST read and understand these instructions before performing any such task. DO NOT DISCARD - GIVE TO USER Table of Contents Technical Data ...................................................................................................3 Specifications ..............................................................................................3 Software ......................................................................................................3 Pin Layout....................................................................................................3 Operating Environment................................................................................3 Declarations .......................................................................................................3 EU DECLARATION OF CONFORMITY......................................................3 WEEE ..........................................................................................................4 FCC and ISED Compliance Statement .......................................................4 FCC and ISED Integration Instructions .......................................................5 Regional Requirements ...............................................................................5 Useful Information .............................................................................................5 Website........................................................................................................5 Country of Origin .........................................................................................5 Warranty ......................................................................................................5 ServAid ........................................................................................................6 Safety Data Sheets MSDS/SDS..................................................................6 2 Atlas Copco Industrial Technique AB - 9839 1630 00 IL-R V1 Technical Data Specifications Specification Frequency range, Bluetooth Frequency range, UWB Transmitting power, Blue-

tooth Transmitting power, UWB Supply voltage Size Motion sensor Antenna Data rate SoC 2400 MHz - 2500 MHz 5500 MHz - 7500 MHz

-0.5 dBm

-10.21 dBm 2.8 V - 3.6 V 19.1 mm x 26.2 mm x 2.6 mm 3-axis accelerometer Channel 5 printed PCB an-

tenna (6.5 GHz) Bluetooth chip antenna 6.8 Mbps (IEEE 802.15.4-2011 UWB compli-

ant ) Nordic Semiconductor nRF52832 The IL-R has a pre-installed firmware. In accordance with 15.21 of e-CFR any manipulation or reprogramming of the module will void the users right to operate the device. Software The firmware on the IL-R offers the following:

Distance measurements between different IL-R modules via UWB. Transmit accelerometer sensor values via UWB radio communication. Communication with a host device to send data, such as distance and acceleration sensor values, from module to host device via the ILC interface. Communication with a host device to receive commands, such as selecting a target IL-R module, from host via the ILC interface. The ILC interface is a proprietary and closed interface. For further information contact your local Atlas Copco represen-

tative. IL-R firmware uses a fixed antenna configuration to op-

erate UWB radio communication. This following can not be changed:

UWB channel 5 6.8 Mbps data rate Safety Information Pin Layout Illustration1: Pin layout for the IL-R module The pins listed below are used for communication with the host device. Pin 1 - GND, 11 - GND, 34 -

GND 12 - VCC 14 I2C_SDA Description GND VDD Communication link to host device (ILC interface) Communication link to host device (ILC interface) Communication link to host device (ILC interface) Communication link to host device (ILC interface) 15 I2C_SCL 18 UART_TX 20 UART_RX Operating Environment Parameter Minimum Maximum Operating temperature Operating hu-

midity

+85

-40 10 95 Unit C

%RH Declarations EU DECLARATION OF CONFORMITY We, Atlas Copco Industrial Technique AB, S-105 23 STOCKHOLM SWEDEN, declare under our sole responsi-

bility that the product (with name, type and serial number, see front page) is in conformity with the following Direc-

tive(s):

2011/65/EU, 2014/53/EU, 2014/30/EU Harmonized standards applied:

EN 300328 V2.1.1, EN 301 489-17 V3.2.0, EN 301 489-33 V2.2.0, EN 301489-1 V2.2.0, EN 302 065-2 V2.1.1, EN 62368-1:2014 Atlas Copco Industrial Technique AB - 9839 1630 00 3 Safety Information Authorities can request relevant technical information from:

Product Compliance Manager, Atlas Copco Industrial Tech-

nique AB, S-105 23 Stockholm Sweden Stockholm, 20 November 2018 Carl von Schantz, Managing Director Signature of issuer WEEE Information concerning Waste of Electrical and Electronic Equipment (WEEE):

This product and its information, meets the requirements of the WEEE Directive (2012/19/EU), and must be handled in compliance with the directive. The product is marked with this symbol:

Products with the symbol of a crossed out wheelie bin with a single black line underneath, indicates that parts within the product must be handled in compliance with the WEEE Di-

rective. The entire product, or the WEEE parts, can be sent to your Customer Centre for handling. FCC and ISED Compliance Statement FCC ID: 2AQ8P-ILR1 ISED certification number: 24224-ILR1 This device complies with: CAN ICES-3 (B)/NMB-3(B) This device complies with part 15 of the FCC Rules. Opera-

tion is subject to the following two conditions: (1) This de-

vice may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes to the IL-R V1 module and / or its firmware, in-

cluding but not limited to modifications to the UWB antenna configuration and / or the UWB antenna, voids the users au-

thority to operate the device. The device is in compliance with the requirement for RF exposure in the US with 20 cm separation distance between the user and the device. The an-

tenna is fixed to the device and no change in antenna or fixa-

tion of the antenna is acceptable and such modification is considered to violate the Compliance Statement. IL-R V1 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-

suant to part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the in-

structions, may cause harmful interference to radio com-

munications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow-

ing measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected. Consult the dealer or an experienced radio/TV tech-

nician for help. This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. Labeling Requirements for End Product For an end product using this IL-R module there must be a label containing, at least, the following information:

This device contains FCC ID: 2AQ8P-ILR1 IC: 24224-ILR1 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compli-

ance with the modular approval guidelines developed by the FCC. In accordance with 47 CFR 15.19 the end product shall bear the following statement in a conspicuous location on the device:

"This device complies with Part 15 of the FCC Rules. Opera-

tion is subject to the following two conditions;

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, includ-

ing interference that may cause undesired operation."

When the device is so small or for such use that it is not prac-

ticable to place the statement above on it, the information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is mar-

keted. In case, where the final product will be installed in lo-

cations where the end-user is not able to see the FCC ID and/

or this statement, the FCC ID and the statement shall also be included in the end-product manual. ISED Compliance Statement:

(English) This device complies with Industry Canadas li-

cence-exempt RSSs. Operation is subject to the following two conditions:

4 Atlas Copco Industrial Technique AB - 9839 1630 00 IL-R V1

(1) This device may not cause interference; and

(2) This device must accept any interference, including inter-

ference that may cause undesired operation of the device.

(French) Le prsent appareil est conforme aux CNR dIndus-

trie Canada applicables aux appareils radio exempts de li-

cence. Lexploitation est autorise aux deux conditions suiv-

antes:

1) lappareil ne doit pas produire de brouillage;

2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromet-

tre le fonctionnement. FCC and ISED Integration Instructions FCC and ISED Integration instructions according to KDB996369 D03 OEM V01 manual section. 2.2 List of applicable FCC/ISED rules used in the certifi-

cation of the IL-R FCC:

47 CFR Part 15F (UWB) 47 CFR Part 15C (Bluetooth) 47 CFR 2.1091 (RF exposure) ISED:

RSS-220 (UWB) RSS-247 (Bluetooth) RSS-102 (RF exposure) 2.3 Specific operational use conditions Not applicable. The IL-R have a printed PCB antenna. 2.4 Limited module procedures The IL-R module is only to be used by the grantee in its own products and is not intended for sale to third parties. Granted Host product for this IL-R is ILT Base Station. Additional hosts to be used must do a class II permissive change appli-

cation. 2.5 Trace antenna design Not applicable 2.6 RF exposure considerations Tested as a mobile device with 0.1 cm as the compliance dis-

tance meeting the power density requirements in the above mention standards. 2.7 Antennas Not applicable. The IL-R have a printed PCB antenna. 2.8 Label and Compliance information Included in this documentation in section FCC and ISED compliance statement and Labeling requirements for end product. 2.9 Information on test modes and additional testing re-

quirements The IL-R module is only to be used by the grantee in its own products and is not intended for sale to third parties. Granted Host product for this IL-R is ILT Base Station which are tested compliant to FCC part 15 B and ICES-001 for the un-

intentional radiator part of the host product. Safety Information 2.10 Additional testing, Part 15 Subpart B disclaimer The IL-R module is only to be used by the grantee in its own products and is not intended for sale to third parties. Granted Host product for this IL-R is ILT Base Station Regional Requirements WARNING This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov Useful Information Website Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website. Please visit: www.atlascopco.com. Country of Origin For the Country of Origin, please refer to the information on the product label. Warranty Product warranty will expire 12 months after the product is first taken into use, but will in any case expire at the latest 13 months after delivery. Normal wear and tear on parts is not included within the warranty. Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools maintenance typical for that period (expressed in time, operation hours or otherwise). The product warranty relies on the correct use, mainte-

nance, and repair of the tool and its component parts. Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the war-

ranty period is not covered by the warranty. To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance sched-

ules and follow the correct instructions. Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners. Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover contracts. For further information contact your local Service representative. For electrical motors:

Warranty will only apply when the electric motor has not been opened. Atlas Copco Industrial Technique AB - 9839 1630 00 5 IL-R V1 Safety Information ServAid ServAid is a portal that is continuously updated and contains Technical Information, such as:

Regulatory and Safety Information Technical Data Installation, Operation and Service Instructions Spare Parts Lists Accessories Dimensional Drawings Please visit: https://servaid.atlascopco.com. For further Technical Information, please contact your local Atlas Copco representative. Safety Data Sheets MSDS/SDS The Safety Data Sheets describe the chemical products sold by Atlas Copco. Please consult the Atlas Copco website for more information www.atlascopco.com/sds. 6 Atlas Copco Industrial Technique AB - 9839 1630 00 Original instructions Atlas Copco Industrial Technique AB SE-10523 STOCKHOLM Sweden Telephone: +46 8 743 95 00 Telefax: +46 8 644 90 45 www.atlascopco.com Copyright 2019, Atlas Copco Industrial Technique AB. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability. Out of respect to wildlife and nature, our technical literature is printed on environmentally friendly paper.

Request for Permanent Confi company name: Atlas Copco FCC ID: 2AQ8P-ILR1 FCC Part 15 Certification Cran In accordance with CFR 47 0.457 and CFR 47 0.459 Atlas Copco Indust AB hereby requests confidenti of following attachments:

(1) schematic diagrams,

(2) detailed block diagrams,

(3) detailed operational descriptions, Ce Cace hese documents contain detailed system and equipment description and related formation about the product which Atlas Copco Industrial Technique AB considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, Atlas Copco Industrial Technique AB considers that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Si nature ee) AC cred) Project Manager Atlas Copco industrial Techniq Sickla Industrivag 19 105 23 Nacka SWEDEN Atlas Copco Industrial Technique AB Atlas Copco AB sie c sy ig address: areas eee lems CSc] 105 23 Stockholm Sickla Industrivag 19 08-743 95 00 ELT www.atlascopco.com/tools Federal Communications Comm Equipment Authorization Branch 435 Oakland Mills Road Otay Ula SMe eee ert) Industrial Technique AB

Sltlas Copco Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Declarence of non-saleability Company name: Atlas Copco Industrial Technique AB FCC ID: 2AQ8P-ILR1 FCC Part 15 Certification To whom it may concern:

Document 4420245732 7/10/2019 According to the FCC document 996369 D03 OEM Manual v01" we hereby declare that the module to be certified with the FCC ID: 2AQ8P-ILR1 will only and exclusively be used for products from Atlas Copco Industrial Technique AB. The module will not be sold to third parties. Furthermore, we prohibit any integration into third-party products. Sincerely, Signature Nadia Dayi Business Manager Total Work Station Atlas Copco Industrial Technique AB Atlas Copco Industrial Technique AB Atlas Copco AB Postal address: Visiting address:

Org. No. 556044-9893 105 23 Stockholm Sickla Industrivag 19 Nacka www.atlascopco.com/tools Phone:

08-743 95 00

08-External Photos FCC ID:

IC:

2AQ8P-ILR1 24224-ILR1 page 1 Project No.: G0M-1806-7488 08-External Photos FCC ID:

IC:

2AQ8P-ILR1 24224-ILR1 page 2 Project No.: G0M-1806-7488

09-Internal Photos FCC ID:

IC:

2AQ8P-ILR1 24224-ILR1 page 1 Project No.: G0M-1806-7488 09-Internal Photos FCC ID:

IC:

2AQ8P-ILR1 24224-ILR1 page 2 Project No.: G0M-1806-7488 page 3 09-Internal Photos FCC ID:

IC:

2AQ8P-ILR1 24224-ILR1 Project No.: G0M-1806-7488

FCC ID: 2AQ8P-ILR1 IC: 24224-ILR1 IL-R Label Location Date: 2018-12-10 15 mm 8 mm Text to go on packaging Model Number: IL-R V1 FCC ID: 2AQ8P-ILR1 / IC: 24224-ILR1 FCC compliance Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. The device is only in compliance if no changes or modifications is made to the device. The device is in compliance with the requirement for RF exposure in the US with 20 cm separation distance between the user and the device. The antenna is fixed to the device and no change in antenna or fixation of the antenna is acceptable and such modification is considered to violate the Compliance Statement. ISED compliance Statement:

(English) This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

(French) Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage;

2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Atlas Copco industrial Technique AB Atlas Copco AB Org. No. 556044-9893 Postal address:

105 23 Stockholm Visiting address:

Sickla Industrivg 19 Nacka www.atlascopco.com/tools Phone:

08-743 95 00

ABB0C12B DM Model: IL-R V1 HVIN: 1 IC: 24224-ILR1 FCC ID: 2AQ8P-ILR1

proval Requ 2018-11 2AQ8P-

ype of Equipment: Radio he following requirements RF shielding fsreya (ola M a: oa Buffered modulation/d Celta ceLeUCce Power supply regulati is integrated Antenna requirements The module comes with requirements are fulfille Stand alone test confi Please referring to test set up configuration photo attr) The module has its own label. The instruction for labelling PIE MU LMT Compliance on specific rule or operating requirements The required FCC rules has been fulfilled and all instructions for maintaining co been clearly stated in the users manual ieee RF exposure requirements are fulfilled for mobile configuration. The installation of the module is restricted to mobile host devices what is clearly stated in the installation instruction of the user manual For portable applications OEM integrators need SAR evaluation and an own FCC ID. module for indoor asset localization systems according to FCC Part 15.212 are met:

s own shielding (see external photos). EER Le

(at-Metal| e114 Coie section 15.203, 15.204 b and 15.204 c two permanently attached antennas. The spurious emission d (see attached test report). Teel Atlas Copco Industrial Technique AB Atlas Copco AB eee Cleon PIS EC ercn eas Org. No, 556044-9893, 105 23 Stockholm Sickla Industrivag 19 08-743 95 00 Nacka www.atlascopco.com/tools Project Manager Atlas Copco Industrial Technique AB et

ee LM GUNS *) 8-100 We, the undersigned, hereby matters relating to applications of all documents related to the Any and all acts carried out b effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Atlas Copco Industrial Technique AB Atlas Copco AB Gere icin Ria bes cscn Phone:

Org. No, 556044-9893 105 23 Stockholm Sickta Industrivag 19 08-743 95 00 ECL) www atlascopco.comtools authorize Eurofins Product Service GmbH to act on our behalf U for equipment authorization FCC ID: 2AQ8P-ILR1 including the signing CR ee Eurofins Product Service GmbH on our behalf shall have the same Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 435 Oakland Mills Road Columbia, MD 21046 Robin Karlsson Project Manager Atlas Copco Indust