FCC ID: LSQ-SBU2000433-2 2Track Base Unit 433 MHz

SBU2000 / 2Track base unit Installation and Operation Guide Information in this documentation is subject to change without notice and does not represent a commitment on part of Elmo-Tech Ltd. The software described in this document is subject to the license agreement that is included with the product, which specifies the permitted and prohibited uses of the product. Any unauthorized duplication or use of this documentation, in whole or in part, in print, or in any other storage or retrieval system is prohibited. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means for any purpose other than the purchasers personal use without the permission of Elmo-Tech Ltd. 2002-2010 Elmo-Tech Ltd. All rights reserved. Unless otherwise noted, all names of companies, products, street addresses, and persons contained herein are part of a completely fictitious scenario and are designed solely to document the use of an Elmo-Tech product. Contact Us Corporate Headquarters Elmo-Tech Ltd. 2 Ha-Barzel St., P.O. Box 13236, 61132 Tel Aviv, Israel Tel: 972-3-7671800 Fax: 972-3-7671801 U.S.A Customers, call 1-800-313-1483 E-mail: contact@elmotech.com Visit us at: www.elmotech.com 2 Table of Contents 3 Installation Instructions for the Electronic Monitoring System 1. SBU2000 Monitoring Unit Placement In order to install the Electronic Monitoring System, you will need to find the best location for the SBU2000 Monitoring Unit. The ideal location for the SBU2000 Monitoring Unit is as close as possible to the center of the house. 4 The SBU2000 Monitoring Unit should be placed on a flat horizontal surface, at least 3 feet off the ground and at least 1 foot away from the wall. The SBU2000 Monitoring Unit should be in an open area away from other electrical appliances, personal computers, laptops or metal objects. 2. Installing the SBU2000 Monitoring Unit In order to install the SBU2000 Monitoring Unit, perform the following steps:

1. Disconnect the telephone cord from the wall telephone socket and plug it into the Phone socket, located on the rear panel of the SBU2000 Monitoring Unit. 2. Connect one end of the supplied telephone cord into the Line socket, located on the rear panel of the SBU2000 Monitoring Unit, and then connect the other end of the same cord into the wall telephone socket. 3. Connect the appropriate end of the power adapter cord into the Power socket located on the rear panel of the SBU2000 Monitoring Unit. 4. Connect the power adapter into a wall power socket. The SBU2000 Monitoring Unit makes an audible beeping sound and then runs through a series of initialisation tests to check that everything is in order. 5 5. After completing the initialisation tests successfully the SBU2000 Monitoring Unit beeps again and the left and right external LED indicators, located on the rear panel of the SBU2000 Monitoring Unit are turned on. This indicates that the SBU2000 Monitoring Unit is in a working state and has automatically switched to standby mode. 3. Installing the 2TRACK Installing the 2TRACK system involves:

1. Collecting the appropriate installation equipment and tools 2. Verifying that the Offender is registered in the E3-MWS software 3. Activating the 2TRACK Tracker unit a. Installation Equipment The kit of installation equipment includes the following items:

1. Tracker unit with carrying pouch and power adapter 2. Transmitter with strap holder 3. Locking clips 6 Warning: The Tracker units battery must be fully charged. Verify the batterys status by plugging the charger into the Tracker unit and removing it. The Tracker units screen displays a power bar to indicate the charge level of the battery. b. Installation Tools You will also need the following installation tools:

1. Manual Reset Device (MRD) for activating the Transmitter 2. Strap locking tool for locking the Transmitter 3. 0.2 (5mm) flat head screwdriver for opening the locking clip 4. Snake eye screwdriver for changing the straps of the Transmitter c. Offender Information in the E3-MWS Verify the following Offender details in the E3-MWS software application:

1. Offenders name and address 2. Offenders program type 2TRACK Active 3. Equipment serial numbers these must match the serial numbers on the equipment you are planning to activate:

a. Tracker unit serial number b. Transmitter serial number Note: The relevant serial numbers are visible on the back or side of each equipment item.

Tracker unit SIM card details For more information about working with the E3-MWS system, refer to the E3-

MWS Monitor Operators Manual. 7 4. Place 2TRACK in SBU2000 Unit The SBU2000 unit device used to recharge the 2TRACK and transmit all GPS location information, violation information, and house arrest status. It also monitors the Ankle Bracelet when the 2TRACK is placed in the base unit

(docked). 5. Installation Manual for bracelet unit Bracelet To Attach the Bracelet 1. Match the Bracelet serial number on the Bracelet case to the number on the Bracelet serial number in the hardware list in PCE. The ankle transmitter and strap will be shipped unattached. You must insert one end of the strap into the transmitter and push the locking pins into place. Make sure that the locking pins are flush with the case. Measure the strap to the offenders leg and cut the strap to fit around the offenders ankle. You should size the strap so that it allows approximately inch of space between the offenders leg and the strap to ensure comfort. 8 2. Once you have the strap attached, push the locking pin through the holes on the bracelet and into the strap until it locks into place 3. Make sure the locking pin is pushed far enough so that the top of the pin is flush with the bracelet case 9 To Remove the Bracelet 1. Cut the strap 2. Using the screwdriver provided, turn the right locking pin counter clockwise and the left locking pin clockwise to remove 3. Lift each side of the pin up from the strap and remove. Slide both ends of the strap out of its channel. Dispose of the strap 4. Clean the bracelet with mild detergent. Rinse, dry, and return to your inventory. Downloading the Curfew Schedule Once the monitoring system has been installed, perform the following:

1. Verify that the right LED located on the rear panel of the SBU2000 Monitoring Unit is constantly on and not flashing. 2. Using a mobile phone, call the monitoring center personnel and ask them to perform a manual download. 10 6. FCC Notices The SBU2000 complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation. 3) Changes or modifications not expressly approved by Elmo Tech Ltd could void the users authority to operate the equipment. ATIS/ACTA Customer Information This equipment, Smart Base Unit, model: SBU x000yyy (1), complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the bottom panel of this equipment is a label, that contains among other information, a product identifier in the format US: LSQAL01BSBx000yyy. If requested, this number must be provided to the Telephone Company. This equipment is designed for connection to the telephone network using an RJ-11 connector, which is Part 68 compliant. See Installation Instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for Smart Base Unit, model: SBU x000yyy, is 0.1B. If the Smart Base Unit, model: SBU x000yyy, causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, you will be notified as soon as possible. Also, you will be advised of your right to file a compliant with the FCC if it is necessary. 11 The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with the Smart Base Unit, model: SBU x000yyy, for repair or warranty information please contact: Pro Tech Monitoring, lnc., 1838 Gunn Highway, Odessa, FL 33556, Phone 888.67.SMART, FAX 813.749.5474. If the equipment is causing harm to the telephone network, the telephone company may request to disconnect the equipment until the problem is resolved. The Smart Base Unit, model: SBU x000yyy, installation is described in Section 2 of the Smart Base Unit, model: SBU x000yyy, Maintenance Manual. Connection to Telephone Company and providing coin service is prohibited. Connection to party lines service is subject to state tariffs.

(1) x = 1 digit number that represents the SBU model's mechanical design. yyy = 3 digit number that represents the SBU model's RF related characteristics. Caution:

Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to the instructions 12

bf Ed eae rr) A LS ee eee SIVIART Base ProTrecn Hu2000418 noi TNCEL NUMELE t NE NN EM A ID QIPTCE IF FOUND CALL (888

"DE | molech MODEL: SBUZ000LL 2Track Base Unit This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: LSQ-SBU2000418 THIS PRODUCT COMPLIES WITH 47 CFR PART 68 SIN: UI OUAG AU A REGISTRATION NUMBER: US:LSQAL01BSBx000yyy XXXXXXXXXK USE STANDARD JACK: USOC RJ11C RINGER EQUIVALENCE NUMBER: 0.1B PIN: O6XXXXXX Contains FCC ID: QIPTC63I Rev: XXX iB +9--

a Made in Israel 12V Sue 2A,

PlaceCompanyLogoHere CONF APPENDIX SBU2000433 BlkDia.pdf CONF APPENDIX SBU2000433 PartsLst.pdf CONF APPENDIX SBU2000433 Schem.pdf Date: 29.06.11 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: LSQ-SBU2000418-4. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request permanent confidential treatment of information accompanying this application as outlined below:

The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signature:

Shai Avigdori Quality Assurance Manager ElmoTech Ltd.

SBU2000LL Operational Description The 2Track Base Unit is a Home Unit monitoring device with a 2-way RF interface (433 MHz transceiver, GFSK Modulation and 38 KHz bandwidth). When the 2Track Base Unit receives a status signal from the monitored device (bracelet tag), it returns an acknowledge signal. In order to enhance the RF coverage, the 2Track Base Unit implements RF diversity (2 transceivers with 2 antennas using different polarization). When activated, the 2Track Base Unit waits for signals from its monitored device, that are transmitted at a pseudorandom interval of between 15 and 16 seconds. Following each received transmission, the 2Track Base Unit returns an acknowledge signal to the monitored device after approximately 10mSec. The 2Track Base Unit compares received information with a schedule that was downloaded from the Monitor center database. By comparing the information, the 2Track Base Unit sends an event to the monitor center via either PSTN or cellular communication. In addition, the 2Track Base Unit acts as a docking station for the X-tech GPS tracking unit. It provides communication to the X-tech unit using the IrDA protocol to exchange information between them. The docking station provides 12VDC in order to recharge the X-tech's battery. The monitored device is a bracelet tag installed on the offender's wrist or ankle, monitored by the system and received by the SBU2000LL. Violations to the offender's curfew schedule generate events that are uploaded to the central monitoring station via the cellular network or PSTN. The SBU20004LL is usually powered by a Wall mounted adapter 100-

240VAC to 12V/2A DC. Backup power is supplied by an Internal 7.4V/

5.2Ah Li-Ion battery pack that provides power for a duration of up to 50 hours. In addition the 2Track Base Unit has an IrDA port for secondary communication with a PC.

PlaceCompanyLogoHere Date: 29.06.11 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Shaike Raz of I.T.L. (Product Testing) Ltd (ITL) to act on our behalf regarding the FCC ID Certification Process for the following application:

FCC ID: LSQ-SBU2000433-2 Thank you, Sincerely, Signature:

Shai Avigdori Quality Assurance Manager ElmoTech Ltd.

PlaceCompanyLogoHere Date: 29.06.11 attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

I hereby declare that there is no tune-up procedure for FCC ID: LSQ-SBU2000433-2 Sincerely, Signature:

Shai Avigdori Quality Assurance Manager ElmoTech Ltd.