FCC ID: 2ANJCALRB058B motion-activated ANYWHERE LIGHT

motion-activated ANYWHERE LIGHT TM 40251,40252 ABOUT YOUR MOTION-ACTIVATED ANYWHERE LIGHT TM Totally portable and weatherproof. 3. D Perfect outdoors for doors, steps, decks, sheds, garages, pathways, porches, and anywhere additional light is needed. Also perfect indoors for hallways, stairways,closets, and bathrooms. Built-in motion sensor automatically turns on the light when movement is detected in the area. The light remains on while motion continues to be detected in the area. Built-in photosensor enables the light to only turn on at night. The 4 super bright LEDs have an estimated life of 30,000 hours, so they never need changing. Requires 4 D cell batteries (not included). The batteries typically last up to 1 year under normal use. 1. To access the battery compartment, twist open the back half of the light counterclockwise. 4. Anywhere TM 2. Remove the battery compartment cover by squeezing the two tabs on the cover inward. Press Tabs 5. Reassemble the Motion-Activated Anywhere Light by twisting the back half of the light clockwise tightly to ensure a weather proof seal. TM Page 2 fresh TM Anywhere TM 1. In order to mount the light securely to a wall or other stable surfaces, the mounting base needs to be installed. Slide the the mounting place to separate it from the main body. 2. If you are installing the mounting place on a very hard surface, you may need to drill holes for the screws first. The included screw anchors can be used for drywall, cement, brick, or similar surfaces. 3. Use the two screws supplied to install the mounting plate. Anywhere Anywhere TM because 25 feet 1. Align the base to the mounting plate. Slide the main body onto the mounting plate until it snaps into place. Anywhere TM Anywhere TM Anywhere TM Depending on your preferences, you can rotate the base on the mounting plate or make the motion sensor and the light swivel to aim at different directions. At night, the LED lights will remain on for approximately 30 seconds after the last detected movement. If a movement is detected while the lights are on, the light duration will be reset and remain on for another 30 seconds. Page 3 3 0.3 approx. 30 seconds Lumens 00 info@maxsainnovations.com FCC Warning and Notes Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

40mm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. m m 0 3

[2020-07-08]

Attention: Application Examiner Naas Request for Confidentiality Applicant: Aurolite Electrical Panyu Guangzhou bBtanvtncrel FCC ID: 2ANJCALRB058B To Whom It May Concern:

Permanent Confidentiality Request is hereby submitted by Aurolite Electrical Panyu Guangzhou Limited to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

e Schematics Detailed Block Diagrams Pek PU mui e emt ns Rationale for request for confidentiality:

Aurolite Electrical Panyu Guangzhou Limited has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive PERE E PET R Cadena erm cee CML RCO RIOR ee testa successful implementation of unpublished leading edge technology developed by us.]

[For FCC certification; delete for TCB certification: The fee for confidentiality has been submitted along with the fee for certification.] If you have questions or need further information, please contact the undersigned. Sincerely, seca lq Luo wangxian anager Aurolite Electrical Panyu Guangzhou Limited Aurolite Electrical Panyu Guangzhou Limited

Aurolite Electrical Panyu Guangzhou Limited Limited Agency Agreement Aurolite Electrical Panyu Guangzhou Limited FCC ID: 2ANJCALRB058B

[2020-07-08]

Federal Communications Commission 445 12th Street SW Washington, DC 20554 Subject:

To Whom It May Concern:

We, Aurolite Electrical Panyu Guangzhou Limited, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number

(2ANJCALRB058B) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (2020-07-08). The Limited Agency Agreement expires on (2020-12-08), unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Luo Wangxian Manager