Original instructions DYNAMIC SERIES Part C: FJR transmitting unit INDEX 1 Description ........................................................................................................... C - 2 2 Technical data ...................................................................................................... C - 3 3 Technical data sheet ........................................................................................... C - 3 4 Plates .................................................................................................................... C - 4 5 Light signals ........................................................................................................ C - 4 6 Malfunction signalled by the transmitting unit ................................................. C - 6 AUTEC LIFJRE00-01.fm Dynamic Series Part C: FJR transmitting unit ENG C - 2 Description 1 Description C B B D B E B A F G B A connector for wire control (if present) C STOP pushbutton E LEDs G S-KEY (electronic starting key) B actuators
(joysticks, selectors, pushbuttons) D display or LED (if present) F START pushbutton Dynamic Series Part C: FJR transmitting unit Technical data C - 3 2 Technical data Power supply (battery MBM06MH)................................................................. NiMH 7.2 V Antenna ................................................................................................................... internal Housing material ........................................................................................... PA 6 (20% fg) Protection degree ....................................................................................... IP65 (NEMA 4) Dimensions ......................................................... 260 x 200 x 190 mm (10.2 x 7.9 x 7.5 In) Weight .......................................................................................................... 2.0 kg (4.4 Lb) Run time (at 20C / 68F) ............................................................................................ 11 h Run time with Data Feedback (at 20C / 68F) .......................................................... 9.5 h Run time with Low Power (at 20C / 68F) .................................................................. 14 h Run time with Data Feedback and Low Power (at 20C / 68F) ............................... 12.5 h 3 Technical data sheet The technical data sheet contains the transmitting unit configuration and shows the matching between commands sent and machine functions/movements. It also contains the wiring diagram showing the connection between the receiving unit and the machine. Each technical data sheet must be filled in, checked and signed by the installer, who is responsible for a correct wiring. A copy of the technical data sheet must always be kept together with this manual
(always keep a copy of this data sheet for administrative purposes). The wiring of the receiving unit outputs must always reflect the wiring indi-
cated in the technical data sheet. AUTEC LIFJRE00-01.fm Dynamic Series Part C: FJR transmitting unit ENG C - 4 Plates 4 Plates The transmitting unit has three plates. Plate Position Content radio remote control identification plate On the S-KEY: remove the S-
KEY to read the plate. transmitting unit iden-
tification plate In the battery housing: remove the battery to read the plate. technical data plate In the battery housing: remove the battery to read the plate. Radio remote control serial number (S/N). Manufacturing year, bar code and transmitting unit identifi-
cation number (TU ID). MODEL, TYPE and main transmitting unit technical data, marking and possible radio remote control marks. 5 Light signals The FJR transmitting units may have two or four LEDs. In both cases, two LEDs are always available, providing information regarding the radio remote control.
- a green LED identified with
- a red LED identified with The green LED ... Meaning
... is off
... blinks fast
... blinks slowly The transmitting unit is switched off. The transmitting unit is switched on and there is no radio link. The radio remote control is started and the radio link is present. Dynamic Series Part C: FJR transmitting unit Light signals C - 5 The red LEDa ... .. is off
...blinks
... is on for 2 secondsb
... blinks onceb
... blinks twiceb
... blinks three timesb
... blinks four timesb Meaning The transmitting unit works correctly. The battery is nearly flat. The transmitting unit does not work correctly. At power on, the transmitting unit detects that the STOP pushbutton is activated or damaged. At power on, the transmitting unit detects that one of the commands D2-D20 or SAFETY is activated or damaged (see technical data sheet). At power on, the transmitting unit detects that the bat-
tery is flat. At power on, the transmitting unit detects that one of the commands A1-A8, L1-L8 and H1-H8 is activated or damaged (see technical data sheet). a. An acoustic signal is also heard when the red LED is illuminated. b. After this signal, the transmitting unit switches off. If it has 4 LEDs, the side LEDs are red and provide information coming from the machine (Data Feedback function).
AUTEC LIFJRE00-01.fm Dynamic Series Part C: FJR transmitting unit ENG C - 6 Malfunction signalled by the transmitting unit 6 Malfunction signalled by the transmitting unit Use the light signals on the transmitting unit to identify the radio remote control malfunction. If the problem persists after the suggested solution has been carried out, contact the support service of the machine manufacturer. Possible reason Solutions The battery is flat. Replace the battery with a charged one. Signals The green LED does not the switch on when START pushbutton is pressed, even though both the battery and the S-KEY are inserted. The green LED blinks fast. The red LED switches on for 2 seconds and then the unit switches off. No radio link. The transmitting unit does not work correctly. The red LED blinks once during start up. The STOP pushbutton is locked or damaged. The red LED blinks twice during start up. At least one of the actuators correspond-
ing to commands D2-
D20 and SAFETY is activated or damaged. Bring the transmitting unit close to the receiving unit. Perform the procedure to save the address.**
Contact the support service of the machine manufacturer. Unlock the STOP pushbutton. If this signal persists, contact the sup-
port service of the machine manufac-
turer. Bring the actuators to the rest posi-
tion. If this signal persists, contact the support service of the machine manu-
facturer. The red LED blinks three times during start up. The battery is flat. Replace the battery with a charged one. The red LED blinks four times during start up. At least one of the actuators correspond-
ing to commands A1-
A8, L1-L8, H1-H8 and SAFETY is activated or damaged. Bring the actuators to the rest posi-
tion. If this signal persists, contact the support service of the machine manu-
facturer.
** Procedure to save the address
- press the STOP pushbutton
- press the START pushbutton and do not release it until the green LED switches off
- unlock the STOP pushbutton Dynamic Series Part C: FJR transmitting unit