FCC ID: WQ8-MK906BT AUTOMOTIVE DIAGNOSTIS AND ANALYSIS SYSTEM

2

" 5 7 DATE POS10N DESCRIPTION FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:

The device has been evaluated to meet general RF exposure requirement. E p A3 1 A B c D r-

B

MaxiCOM MK906BT ADVANCED DIAGNOSTIC & INFORMATION SYSTEM FCC ID: WQ8-MK906BT This device complies with part 15 of the FCC rules. Operation of this device is subject to the following The equipment has internal arcing or sparking parts which two conditions: should not be exposed to flammable vapours. Locate the

(1) this device may not cause harmful interference, and equipment at least 460mm or more above the floor.

(2) this device must accept any interference received, including interference that may cause undesired operation. Am ce &

ALL RIGHTS RESERVED. DO NOT REMOVE. MADE IN CHINA WWW.AUTEL.COM DC Input:

DC 12V==3A

TCBAuthoritytoActasAgent Number:

Revision:

Effectivedate:Oct8,2021 MS0045317 0 Authority to Act as Agent Date: 24 August 2022 TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint TUV Rheinland (Shenzhen) Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with Autel Intelligent Tech. Corp., Ltd. / 7th-8th, 10th Floor, Bldg. B1, Zhiyuan,Xueyuan Rd. Xili, Nanshan, Shenzhen China 518055 For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Date:

12 Months Agreement is valid for 12 months from the above date. By:

Frank Li

(Print name)

+86-0755 86147779

(Telephone)

(Signature) President

(Title) On behalf of:

Autel Intelligent Tech. Corp., Ltd.

(Company Name) Page 1 of 1

ACX Advanced Ceramic X AT3216 Series Multilayer Chip Antenna Features

Monolithic SMD with small, low-profile and light-weight type.

Wide bandwidth Applications

Bluetooth/Wireless LAN/Home RF

ISM band 2.4GHz applications Specifications Frequency Part Number Range

(MHz) Peak Gain Average Gain XZ-V XZ-V VSWR Impedance AT3216 2400 ~ 2500 0.5 dBi typ.

-0.5 dBi typ. 2 max. 50

-B2R7HAA_ Qty/Reel (pcs) Operating Temperature Range Storage Temperature Range Power Capacity Part Number

: 3,000pcs

: -40 ~ +85 oC

: -40 ~ +85 oC

: 3W max. AT 3216 - B 2R7 HAA

Type AT : Antenna

Dimensions ( L W ) 3.2 1.6 mm

Material Code B

Frequency Range 2R7=2700MHz

Specification Code HAA

Packaging T: Tape & Reel B: Bulk

Soldering

=lead-containing

/LF=lead-free Terminal Configuration

No.

Terminal Name No. Terminal Name Feeding Point

NC Dimensions and Recommended PC Board Pattern ACX Advanced Ceramic X W L Unit : mm a T Mark L W T a Dimensions 3.20.2 1.60.2 1.3+

0.1/-0.2 0.50.3

(a) Without Matching Circuits

(b) With Matching Circuits 2.6 3.3nH 1.2pF 1.6

2.7nH 4.2 1.9 0.4

*Line width should be designed to match 50 characteristic impedance, depending on PCB material and thickness. Typical Electrical Characteristics (T=25oC)

Test Board Ground 19mm 50 Feed Line ACX Advanced Ceramic X 13.5mm 6.5mm Matching Circuit No Ground 39.5mm 4mm Antenna 6.5mm

Return Loss

(a) Without Matching Circuits

(b) With Matching Circuits ACX Advanced Ceramic X Radiation Patterns XY-V/XY-H Z 180o XY cut @2.45GHz Vertical Horizontal 90o 90o X 270o Y 0o XY-cut scanning direction XZ-V/XZ-H Y 180 XZ cut @2.45GHz Vertical Horizontal X 270o Z 0o XZ-cut scanning direction YZ-V/YZ-H

. YZ cut @2.45GHz Vertical Horizontal X 180 90o Y 270 Z 0o YZ-cut scanning direction Advanced Ceramic X Corp. 16 Tzu Chiang Road, Hsinchu Industrial District Hsinchu Hsien 303, Taiwan TEL:886-3-5987008 FAX:886-3-5987001 E-mail: acx@acxc.com.tw http://www.acxc.com.tw

Confidentiality Letter Date: 2022-8-23 Subject: Confidentiality Request for FCC ID: WQ8-MK906BT. Pursuant to FCC 47 CRF 0.457(d) and 0.459 the applicant requests that a part of the subject FCC/IC application be held confidential Type of Confidentiality Requested | Exhibit

[D1Short Term Bi Permanent Block Diagrams

[Short Term [Permanent Tnternal Photos ***

[LJ Short Term KX) Permanent Operation Description/Theory of Operation Short Term LJ Permanent Tune-Up Procedure Di Short Term Dx]Permanent Schematics

[Short Term (7 Permanent User's Manual**

[LJ Short Term na Test Setup

[C1Short Term nla External Photos Autel Intelligent Tech. Corp. Ltd, has spent substantial effort in developing this product and it is one of the Tirst of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidenti The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. (*** PAG only) Short-Term Confidentialit The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __(specify number of days not to exceed 180) ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, pron hh By: li Frank Li SignaturerTitey Print name) Ms-00447 15 Page tof t Revision 0

ModelDifferenceStatement Hereby have our company: AutelIntelligentTechnologyCorp., Ltd.ProductnameADVANCEDDIAGNOSTIC&INFORMATIONSYSTEM, Product number MaxiCOM MK906BT Series model MaxiSys MS906BTMaxiSysMS906S The series model is consistent with the main model in circuit design,circuitlayoutandinternalstructure,thedifferenceismainlydueto theinconsistentmodelnameandsalesarea. Stamp AutelIntelligentTechnologyCorp.,Ltd. Date 08th, Aug, 2022.

Dongguan Guoxu Electronics Communication Co.,Ltd. SPECIFICATION FOR APPROVAL Date File No Revision 2016/08/15 16081502 1.0 MAXISYS906TS WIFI Antenna L=120mm FPC TO I-PEX GX005I.300023.I01 CUSTOMER:

CUSTOMER NO:

PART NAME:

SUPPLIER NO:

Date:

Q"TY: PCS CUSTOMER APPROVED BY APPROVAL CHIEF SUPERVISOR SUPPLIER SIGNATURE APPROVAL CHECK DESIGN Shane LiuNi ChenXingCheng add149B2Tel:0769-85535057 Fax:0769-81664308 GX-RD-F04-B Contents Number of Page Page Code Spec Cover Spec Item Drawing Antenna Specification S S Parameter Passive Test Antenna Profile Material Certificate RoHS RoHS Test Report N/A

1 1 1 1 1 2 2 6

N/A

1 2 3 4 5 6 ~ 7 8 ~ 9 10 ~ 15

N/A

NO

. 1 2 3 4 5 6 7 8 9 10 11 12 13 add149B2Tel:0769-85535057 Fax:0769-81664308 RoHS I E m A DESCRIPTION DATE 2016.04.23 2016.07.19 1E B!

181 3 I FPCB I 30.5*22.2MM 2 I Coaxial Cable I o .13G 1 IMininnectorI Au Pia1 NO I PANAMEI DCRIPTION 1 FPCB I FPC100P01 1 0.D 3 I COA100

:u I TER10001A MaalI Part Numbe 1 1w GuoXu Elni Communi aua%U Dongguan PART NAME: WiFi Antenna L=105mm MHF PART NO.: GX0051.300023.101 APPROVED BY DESIGNED BY Tel :073S057 tionCo.,Ltd. Fax:O-81884308 DATE: 2016-07-19

...... a I Toleran x.x 0.50 SCALE: if1. I XJOC0.15 A I X0 REVISION:

3 Antenna Specification Electrical Properties Frequency Impedance V.S.W.R Return Loss Radiation Gain (Peak) Polarization Connector 2400~2484MHz 50 Ohm Nominal 1.92: 1 Max

-10 dB Max Omni-directional See Page 7 Linear 1IPEX Physical Properties Antenna Material FPC TO IPEX Cable Type FOR 1.13CABLE L=120mm Operating Temp. Storage Temp.

-10 ~ +60 C

-10 ~ +70 C Cable Color Gray add149B2Tel:0769-85535057 Fax:0769-81664308 Antenna Performance Test Agilent E5071B add149B2Tel:0769-85535057 Fax:0769-81664308 Antenna Passive Test add149B2Tel:0769-85535057 Fax:0769-81664308 Passive Test For WIFI Effi

(%) 45.1 46.5 46.3 49.4 49.2 50.1 49.7 49.8 49.9 49.0 47.7 Effi

(dB)

-3.5

-3.3

-3.3

-3.1

-3.1

-3.0

-3.0

-3.0

-3.0

-3.1

-3.2 Freq

(MHz) 2400 2410 2420 2430 2440 2450 2460 2470 2480 2490 2500 Gain

(dBi) 0.8 0.9 0.9 1.3 1.3 1.45 1.3 1.45 1.45 1.3 1.3 add149B2Tel:0769-85535057 Fax:0769-81664308 SPECIFICATION FOR APPROVAL

~ 10 ~

SPECIFICATION FOR APPROVAL

~ 11 ~

SPECIFICATION FOR APPROVAL

~ 12 ~

Justification for Re-use of radio test results We, Autel Intelligent Tech. Corp., Ltd., believe that the conducted signal tests for wifi module AP6212 in the original reports for model MaxiSys MS906BT can be re-used for the current model MaxiCOM MK906BT, as the following reason:

The difference between them is that the new design of MaxiCOM MK906BT to integrate with new BT module. This change not affects wifi in conducted signals. FCC ID: WQ8-MK906BT FCC ID: WQ8MAXISYSMY906BT As per KDB 484596 D01 Referencing Test Data v01, conducted signal tests in following reports re-used. FCC Part 15.247, Referrence ID FCC ID:

Report No. Approval date WQ8MAXISYSMY906BT R021700090W2 Approved on 27 Feb. 2018 Autel Intelligent Tech. Corp., Ltd. 7th-8th, 10th Floor, Bldg. B1, Zhiyuan, Xueyuan Rd. Xili, Nanshan, Shenzhen, 518055, China By:

___________________ ______________ __________Frank Li______________

(Signature/Title)

(Print name)