FCC ID: WQ8N8PS20134 MX-Sensor

E m a i l : s a l e s @ a u t e l . c o m W e b : w w w . a u t e l . c o m www.maxitp m s . c o m PRE-PROGRAMMED UNIVERSAL TPMS SENSOR 433MHz-PL MX-Sensor

(Screw-in) NOTE:

433MHz-PL MX-Sensor is pre-programmed for the majority of European vehicles such as Mercedes-Benz, BMW, Audi, Volkswagen, Peugeot, Citroen, Fiat, and Porsche, and is 100% programmable for all supported vehicles. This sensor is not designed for use on vehicles driving in racing competition. Ensure vehicles with sensor installed maintain speeds below 300km/h (186mph). WARRANTY AUTEL guarantees that the sensor is free from material and manufacturing defects for a period of twenty-four (24) months or for 25,000 miles, whichever comes rst. AUTEL will at its discretion replace any merchandise during the warranty period. The warranty shall be void if any of the following occurs:

1. Improper installation of products 2. Improper usage 3. Induction of defect by other products 4. Mishandling of products 5. Incorrect application 6. Damage due to collision or tire failure 7. Damage due to racing or competition 8. Exceeding specic limits of the product SAFETY INSTRUCTIONS Before installing the sensor, read the installation and safety instructions carefully. For reasons of safety and for optimal operation, we recommend that any maintenance and repair work be carried out by trained experts only, in accordance with the guidelines of the vehicle manufacturer. The valves are safety-relevant parts which are for professional installation only. Failure to do so may result in the failure of the TPMS sensor. AUTEL does not assume any liability in case of faulty or incorrect installation of the product. intended CAUTION The TPMS sensor assemblies are replacement or maintenance parts for vehicles with factory installed TPMS. Do not install TPMS sensors in damaged wheels. In order to guarantee optimal function, the sensors may only be installed with original valves and accessories provided by AUTEL. Upon completing the installation, test the vehicle's TPMS following the procedures described in the original manufactur-

er's user guide to conrm proper installation. EXPLODED VIEW OF SENSOR Screw Sensor body Valve stem, rubber grommet and valve core assembly Washer Screw-nut Cap Sensor Specications Weight of sensor without valve 16.5 g Dimensions approx. 51.97*29.08*22.25 mm Max. pressure range 800 kPa PdfEditor 4.0.0.14 Testversion - https://www.pixelplanet.com/de/pdfeditor/

CAUTION: Each time a tire is serviced or dismounted, or if the sensor is removed or replaced, it is mandatory to replace with Autel manufactured or delivered rubber grommet, washer, screw nut, and valve core in order to ensure proper sealing. It is mandatory to replace the sensor if it is externally damaged. Correct sensor nut torque: 4 Newton-meters INSTALLATION GUIDE IMPORTANT: Before operating or maintaining this unit, please read these instructions carefully and pay extra attention to the safety warnings and precautions. Use this unit correctly and with care. Failure to do so may cause damage and/or personal injury and will void the warranty. 1 Loosening the tire Remove the valve cap and core and deate the tire. Use the bead loosener to unseat the tire bead. CAUTION: The bead loosener must be facing the valve. 2 Dismounting the tire Clamp the tire onto the tire changer, and adjust the valve at 1 o'clock relative to the tire separation head. Insert the tire tool and lift the tire bead onto the mounting head to dismount the bead. CAUTION: This starting position must be observed during the whole dismounting process. Tire separation head Tire tool 3 4 Dismounting the sensor Remove the fastening screw and the sensor from the valve stem with a screwdriver, and then loosen the nut to remove the valve. Mounting sensor and valve Slide the valve stem through the valve hole of the rim. Tighten the screw-nut with 4.0Nm with the help of the xed rod. Assemble the sensor and the valve stem together by screw. Hold the sensor body against the rim and tighten the screw. Step 1 Step 2 Step 3 Step 4 5 Mounting the tire Place the tire on the rim, and make sure that the valve faces the separation head at an angle of 180 o. Mount the tire over the rim. PdfEditor 4.0.0.14 Testversion - https://www.pixelplanet.com/de/pdfeditor/

CAUTION: The tire should be mounted to the wheel using tire changer manuf-

acturers instructions. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two con ditions: (1) this device may not cause harmful interference, and (2) this device must accept any i nterference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital d evice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable prot ection against harmful interference in a residential installation. This equipment generates uses a nd can radiate radio frequency energy and, if not installed and used in accordance with the instr uctions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harm ful interference to radio or television reception, which can be determined by turning the equip ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help important announcement Important Note:

PdfEditor 4.0.0.14 Testversion - https://www.pixelplanet.com/de/pdfeditor/

ISED Statement English: This device complies with Industry Canada licenseexempt RSS standard(s).Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) T his device must accept any interference, including interference that may cause undesired operat ion of the device.The digital apparatus complies with Canadian CAN ICES3 (B)/NMB3(B). French:Le prsentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillagera diolectriquesubi, mmesi le brouillageest susceptible d'encompromettre le fonctionnement. This radio transmitter (ISED certification number: 10826A-N8PS20134) has been approved by Industry Canada to operate with theantenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with thisdevice. Le prsentmetteur radio (ISED certification number: 10826A-N8PS20134) atapprouv par Industrie Canada pour fonctionner avecles types d'antennenumrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclusdanscetteliste, etdont le gain estsuprieur au gain maximal indiqu, sontstrictementinterdits pour l'exploitation de l'metteur. PdfEditor 4.0.0.14 Testversion - https://www.pixelplanet.com/de/pdfeditor/

Autel Intelligent Tech. Corp., Ltd. Agent Authorization Company:Autel Intelligent Tech. Corp., Ltd. Address: 7th-8th, 10th Floor, Bldg. B1, Zhiyuan, Xueyuan Rd., Xili, Nanshan Shenzhen China Product Name: MX-Sensor Model Number(s): 433MHz Glue Potting, 433MHz-PL Glue Potting Product Description: MX-Sensor We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Frank Li Title:

Manager Company: Autel Intelligent Tech. Corp., Ltd. Date: 2021.8.24

Autel Intelligent Technology Corp.,Ltd 7th-8th, 10th Floor, Building B1, Zhiyuan, Xueyuan Road, Xili, Nanshan, Shenzhen, 518055, China Product Similarity Declaration Date: August 24, 2021 Model Number: 433MHz Glue Potting, 433MHz-PL Glue Potting To Whom It May Concern, We, Autel Intelligent Technology Corp.,Ltd., declare that EUT (MX-SENSOR) Model Numbers 433MHz Glue Potting, 433MHz-PL Glue Potting. the all models are the same on the board, Schematic, Hardware version, Software version, structure and internal _photos are same, only the model name different. Product name Brand Name_ | Model name Difference AUTEL 433MHz Glue | NA MxX-Sensor Potting 433MHz-PL Glue | NA Potting Should you have any questions or comments regarding this matter, please have my best attention. Sincerely,

(Signed) a, NED BSN ee Name / Title: Frank (Li#Mana a Company: Autel Intelligent Slo Address: 7th-8th 10th Floor, Building B1,;

Shenzhen, 518055, China //7 ly Phone: 0755-22672616 ss 93%

Fax: /

Email: [email protected] rp.,Ltd. "

Autel Intelligent Tech. Corp., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: WQ8N8PS20134 Date: 2021.8.24 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Frank Li Title: Manager Signature of applicant Date: 2021.8.24