WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6045032.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case QUICK START GUIDE Autel Smart Controller V3 1. DISCLAIMER To ensure safe and successful operation of your Autel smart remote controller, please strictly follow the operating instructions and steps in this guide. If the user does not abide by the safety operation instructions, Autel Robotics will not be responsible for any product damage or loss in use, whether direct or indirect, legal, special, accident or economic loss (including but not limited to loss of profit), and does not provide warranty service. Do not use incompati-
ble parts or use any method that does not comply with the official instructions of Autel Robotics to modify the product. The safety guidelines in this document will be updated from time to time. To ensure you get the latest version, please visit the official website:
https://www.autelrobotics.com/
2. BATTERY SAFETY The Autel smart remote controller is powered by a smart lithium-ion battery. Improper use of lithium-ion batteries can be dangerous. Please ensure that the following battery usage, charging and storage guidelines are strictly followed. WARNING:
Only use the battery and charger provided by Autel Robotics. It is forbidden to modify the battery assembly and its charger or use a third-party equipment to replace it. The electrolyte in the battery is extremely corrosive. If the electrolyte spills into your eyes or skin accidentally, please rinse the affected area with clean water and seek medical attention immediately. 3. PRECAUTIONS When using the Autel Smart Controller (hereinafter referred to as the "Smart Controller"), if improperly used, the aircraft may cause a certain degree of injury and damage to people and property. Please be cautious while using it. For details, please refer to the aircrafts disclaimer and safety operation guidelines. 1. Before each flight, make sure that the Smart Controller is fully charged. 2. Make sure the Smart Controller antennas are unfolded and adjusted to the appropriate position to ensure the best possible flight results. 1 3. If the Smart Controller antennas are damaged, it will affect the performance, please contact the after-sales technical support immediately. 4. If the aircraft is changed, it needs to be repaired before using. 5. Make sure to turn off the aircraft power before turning off the remote controller each time. 6. When not in use, make sure to fully charge the smart controller every three months. 7. Once the power of the smart controller is less than 10%, please charge it to prevent an over-discharge error. This is caused by the long-term storage with a low battery charge. When the smart controller will not be in use for an extended time, discharge the battery between 40%-60%
before storage. 8. Do not block the vent of the Smart Controller to prevent overheating and diminished performance. 9. Do not disassemble the smart controller. If any parts of the controller are damaged, contact Autel Robotics After-Sale Support. 4. AUTEL SMART CONTROLLER The Autel Smart Controller can be used with any supported aircraft, and it provides a high-definition real time image transmission and it can control the aircraft and camera up to 15km (9.32 miles) [1] communication distance. The Smart Controller has a built-in 7.9-inch 2048x1536 ultra-high-definition, ultra-bright screen with a maximum 2000nit brightness. It provides clear image display under the bright sunlight. With its convenient, built-in 128G memory it can store your photos and videos on board. The operating time is about 4.5 hours when the battery is fully charged and the screen is at 50%
brightness [2]. 5. ITEM LIST NO DIAGRAM ITEM NAME QTY 1 Remote Controller 1PC 2 2 3 4 5 6 7 Smart Controller Protective Case A/C adapter USB Type-C cable Chest Strap 1PC 1PC 1PC 1PC Spare Command Sticks 2PCS Documentation
(Quick Start Guide) 1PC
[1] Fly in an open, unobstructed, electromagnetic interference-free environment. The smart controller can reach the maximum communi-
cation distance under FCC standards. Actual distance may be less based on the local flight environment.
[2] The above-mentioned working time is measured in a laboratory environment at room temperature. The battery life will vary in different usage scenarios. 3 6. CONTROLLER LAYOUT 4 5 6 7 8 9 10 3 2 1 11 12 13 Top view 1. Left Command Stick 2. Gimbal Pitch Angle Wheel 3. Video Recording Button 4. Customizable Button C1 5. Air Outlet 6. HDMI Port 7. USB TYPE-C Port 8. USB TYPE-A Port 9. Power Button 10. Customizable Button C2 11. Photo Shutter Button 12. * Zoom Control Wheel 13. Right Command Stick
*The function may alter, please take the practical effect as standard. 15 14 19 18 16 17 Front view 14. Battery Indicator 15. Antenna 16. Touch Screen 17. Pause Button 18. Return to Home (RTH) Button 19. Microphone 4 20 21 22 24 23 Rear view 20. Speaker hole 21. Tripod Mount Hole 22. Air Vent 23. Bottom Hook 24. Grips 7. POWER ON THE SMART CONTROLLER 7.1 Check Battery Level Press the power button to check the battery life 1 light solid on: Battery25%
2 lights solid on: Battery50%
3 lights solid on: Battery75%
4 lights solid on: Battery=100%
5 7.2 Powering on/off Press and hold the power button for 2 sec to turn on and off the Smart Controller. 7.3 Charging Remote Controller indication light status 1 light solid onBattery25%
2 lights solid onBattery50%
3 lights solid onBattery75%
4 lights solid onBattery=100%
NOTE: LED indication light will blink while charging 8. ANTENNA ADJUSTMENT Unfold the Smart Controller antennas and adjust them to the optimal angle. The signal strength varies when the antenna angle is different. When the antenna and the back of the remote controller are at an angle of 180 or 260, and the antenna surface is facing the aircraft, the signal quality of aircraft and controller will reach the optimal condition. 6 NOTE:
LED indicator will flash while charging Do not use other communi-
cation equipment which has the same frequency band at the same time, to avoid the interference to the Smart Controller signal. During operation, the Autel Explorer app, will prompt the user when the image transmission signal is poor. Adjust the antenna angles according to the prompts to ensure the Smart Controller and aircraft have the best communication range. o 100 9. FREQUENCY MATCH When the Smart Controller and the aircraft are purchased as a set, the Smart Controller has been matched to the aircraft at the factory, and it can be used directly after the aircraft is activated. If purchased separately, please use the following methods to link. 1. Press (short press) the linking button next to the USB port on the right side of the aircraft body to put the aircraft into the linking mode. 2. Power on the Smart Controller and run the Autel Explorer app, enter the mission flight interface, click the gear icon in the upper right corner, enter the settings menu, click "remote control -> data transmission and image transmission linking> start linking", wait a few seconds until the data transmission is set correctly and the linking is a success. 7 10. FLIGHT Open the Autel Explorer app and enter the flight interface. Before takeoff, place the aircraft on a flat and level surface and face the rear side of the aircraft towards you. Manual takeoff and landingMode 2 Toe in or out on both command sticks for about 2 seconds to start the motors Manual Takeoff or Push up slowly Left Command Stick
(mode 2) Manual landing Push down slowly Left Command Stick Mode 2 8 NOTE:
Before takeoff, place the aircraft on a flat and level surface and face the rear side of the aircraft towards you. Mode 2 is the default control mode of the Smart Controller. During the flight, you can use the left stick to control the flight altitude and direction, and use the right stick to control the forward, backward, left and right directions of the aircraft. Please make sure that the Smart Controller has successfully matched with the aircraft. 11. Command Stick Control (Mode 2) Left Command Stick Left Side Veiw Left Side Veiw Ascend Descend Upward Downward Top View Nose Rotates Left Top View Nose Rotates Right Move Left Move Right 9 Left Side Veiw Left Side Veiw Right Command Stick Forward Backward Nose Rear Nose Rear Forward Downward Rear View Rear View Left Right Move Left Move Right 10 12. Specifications Image Transmission
*Working Frequency Transmitter Power (EIRP) 902-928MHzFCC 2.400-2.4835GHz 5.725-5.850GHzNon-Japan 5.650-5.755GHzJapan FCC33dBm CE20dBm@2.4G14dBm@5.8G SRRC20dBm@2.4G 33dBm@5.8G Max Signal Transmission Distance (No interference, No obstacles) FCC: 15km CE/SRRC: 8km Wi-Fi Protocol Wi-Fi 802.11a/b/g/n/ac, 2x2 MIMO
* Working Frequency 2.400-2.4835GHz 5.725-5.850GHz Transmitter Power (EIRP) Other Specifications Battery Operating Hours FCC26 dBm CE20 dBm@2.4G14 dBm@5.8G SRRC20 dBm@2.4G26 dBm@5.8G Capacity5800mAh Voltage11.55V Battery TypeLi-Po Battery Energy67 Wh Charging time120 min
~ 3h (Max Brightness)
~ 4.5 h (50% Brightness) 11 Internal Storage Video Output Port 128GB HDMI Port USB-A Voltage/Current 5V / 2A Operating Temperature
-20 to 40 Storage Temperature
-20 to 25<1 year
-20 to 451-3 months
-20 to 60<1 month Charging Temperature 5 to 45
**Supported Aircrafts EVO II Pro V3 EVO II Dual 640T V3 EVO II RTK Series V3 EVO II Enterprise V3 Satellite Positioning Module GPS/GLONASS/Galileo/Bei-
Dou/NavIC/QZSS Dimensions Weight NOTE:
30319087mm (with antenna folded) 30327387mm (with antenna unfolded) 1150g (without protective case) 1250g (with protective case)
* The working frequency band varies according to different countries and models.
** We will support more Autel Robotics aircraft in the future, please visit our official website https://www.autelrobotics.com/ for the latest information.
*** The steps to see the certification e-lable:
1. Select Camera ( ) 2. Click the gear icon in the upper right corner ( ), enter the settings menu 3. Select Certification Mark ( ) 12 Model EF9-3 United States FCC ID 2AGNTEF9240958A This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Canada Europe Australia Japan 20910-EF9240958A IC CAN ICES-003(B) / NMB-003(B) Autel Robotics Co., Ltd. 18th Floor, Block C1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan District, Shenzhen, Guangdong, 518055, China 5GHz band (W52) Indoor use only XXX-XXXXXX South Korea United Kingdom R-C-A4R-EF9-3
: Autel Robotics Co., Ltd. /
TAIWAN Battery CCXXxxYYyyyZz W 11.55V Li-ion 5800mAh Autel Robotics Co., Ltd. Made in China 13 FCC and ISED Canada Compliance This device complies with part 15 of the FCC Rules and ISED Canada licence-exempt RSS standards. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dISED Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lappareil doit accepter tout brouillage radiolec-
trique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Specic Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certied power level in all tested frequency bands, although the SAR is determined at the highest certied power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model device is an available for sale to the public, it must be tested and certied to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC. For limb worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal. For body worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the device a minimum of 10mm from the body. ISED Specic Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the ISEDC with the device transmitting at its highest certied power level in all tested frequency bands, although the SAR is determined at the highest certied power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model device is an available for sale to the public, it must be tested and certied to the ISEDC that it does not exceed the exposure limit established by the ISEDC, Tests for each device are performed in positions and locations (e.g. at the ear and worn on the body)as required by the ISEDC. For limb worn operation, this device has been tested and meets the ISEDCRF exposure guidelines when used with an accessory designa ed for this product or when used with an accessory that contains no metal. For body worn operation, this device has been tested and meets the ISEDC RF exposure guidelines when used with an accessory designat ed for this product or when used with an accessory that contains no metal and that positions the device a minimum of 10mm from the body. Tauxdabsorptionspcique (SAR) informations les tests SAR le plus levdanstoutes sonteectus en utilisant les positions oprationnellesnormalisesac ceptespar la ISEDC, le dispositifmettant son niveau de puissance certi estes.Avantquun nouveau modle de dispositif ne soitdisponible la vente aupublic, ildoittretest et certi la ISEDC quil ne dpasse pas la limitedexpositiontablieparla ISEDC, les Tests pour chaquedisposi tifsonteectusdans des positions et des emplacements(par exemple loreille et portsur le corps) commelexige la ISEDC. les bandesdefrquencest Pour le fonctionnement desmembresuss, cetappareil a ttest et rpond aux lignesdirectricesdexposition aux RF ISEDClorsquilestutilis avec un accessoiredsign pour ceproduitoulorsquilestutilis avec unaccessoire qui ne contient pas de mtal. Pour le fonctionnement du corps us, cetappareil a ttest et rpond aux lignesdirectricesdexposition RF ISEDC lorsquilestutilis avec un ceproduitoulorsquilestutilis avec un accessoiredsign pour accessoire qui ne contient pas de mtal etqui positionnecet appareil au moins 10mm du corps. Autel Robotics Co., Ltd.hereby declares that this wireless device is in compliance with Directive 2014/53/EU and Radio Equipment Regulations 2017. 9th Floor, Building B1, Zhiyuan, Xueyuan Road, Xili,Nanshan,Shenzhen,518055, China 22522 29th Dr SE STE 101, Bothell, WA 98021 United States Toll-free: (844) MY AUTEL or (844) 692-8835 www.autelrobotics.com Wi-Fi 802.11a/b/g/n/ac, 2x2 MIMO 2.400-2.4835GHz 5.725-5.850GHz FCC26 dBm CE20 dBm@2.4G14 SRRC20 dBm@2.4G26 dBm@5.8G dBm@5.8G Capacity5800mAh Voltage11.55V Battery TypeLi-Po Battery Energy67 Wh Charging time120 min
~ 3h (Max Brightness)
~ 4.5 h (50% Brightness) 2022 Autel Robotics Co., Ltd. All Rights Reserved