Series V3 QUICK START GUIDE 1. OVERVIEW The EVO II RTK Series V3 brings excellent flight performance, achieving a top speed of 20m/s (45mph), 36-minute flight time, and an operating distance at 15km (9.32miles, FCC). The aircraft comes with a 7.9 inch touch-screen controller, boasts a 2048x1536 pixel resolution. NOTE:
Please read all documentation before your first flight.Failure to operate the aircraft responsibly could lead to injury or damages, and may void any applicable warranty coverage. 2. AIRCRAFT Propellers Motors Front Vision System Gimbal Camera Front LED Indicators RTK Module Landing Gear 1 Power Button Rear LED Indicators Rear Vision System Left Vision System SD Card Slot Right Vision System USB Port Aircraft Battery Air Vent 2 Pairing Button / Pairing Indicator Upward Vision System Ultrasonic Sensor Downward Vision System Downward Vision Lighting LED 3 3. FLIGHT LED INDICATIONS A LED indicator is located on the end of each aircraft arm. The front LEDs will light up solid red to help you identify the direction of the aircraft's nose. The rear LEDs will display the current flight status of the aircraft. The chart below shows the meaning of each status indicator. Indicator Key:
Slow Flashing:
Flashes once every 2s Color Key R Red Color Fast Flashing: Flashes twice per second G Yellow Color Alternate Flashing: Alternates among different colors Y Green Color Definitions of Indicator Status Normal RGY Alternate Flashing System self-test is activated YG - Alternate Flashing The aircraft is warming up G Slow Flashing The aircraft is in GPS mode Warning Y - Slow Flashing The aircraft is in ATTI mode Y - Fast Flashing No connection between the aircraft and smart controller R - Slow Flashing Low Battery Warning R - Fast Flashing Critically Low Battery Warning R Solid Light Critical problems, IMU error RY Alternate Flashing Abnormal compass, calibration is required /
Magnetometer interference Compass Calibration Y - Fast Flashing Be ready to calibrate the compass/ The aircraft is calibrating G Solid Light Calibration is successful R Solid Light Calibration is failed 4 4. REMOTE CONTROLLER Left Command Stick HDMI Port Customizable Button C2 Gimbal Pitch Angle Wheel USB-C Port Video Recording Button USB-A Port Photo Shutter Button
*Zoom Control Wheel Customizable Button C1 Power Button Right Command Stick Air Outlet
*The function may alter, please take the practical effect as standard. Battery Indicator Antenna Touch Screen Pause Button Auto-takeoff/
RTH Button Microphone 5 Speaker Hole Air Vent Grips Tripod Mount Hole Bottom Hook 5. CHARGING Aircraft Battery: Plug the charging connector into the batterys charge
(1) port, and connect the other end to power adapter. Plug the power adapter into a power outlet (100-240V AC). Controller: Connect the charging cable to the USB port at the top of the
(2) controller, and the other end to power adapter. Plug the power adapter into a power outlet (100-240V AC). NOTE:
Always fully charge the aircraft and smart controller batterybefore flying. It takes approximately 90 minutes to fully charge the aircraft battery,and 120 minutes to charge the controller. 6 6. AUTEL EXPLORER APP Search for Autel Explorer from Google Play and install the app on your controller. 7. PREPARING THE AIRCRAFT Before powering on the aircraft, please remove the gimbal guard.
(1) Unfold the arms and propellers.
(2) NOTE:
Power off the aircraft before folding the arms. Fold in the rear arms and propellers first, and then the front ones. 7 8. PROPELLERS Because the propellers come attached to the aircraft, the following instructions apply if you need to reinstall propellers. Attaching the Propellers Power off the aircraft.
(1)
(2) mark . Pair the propellers and corresponding motors according to the white Press each propeller down firmly and rotate in the lock direction to
(3) securely attach the propeller. Detaching the Propellers Power off the aircraft.
(1)
(2) detach the propeller. Press each propeller down firmly and rotate in the unlock direction to LEGEND Lock Direction: Fasten the propeller by rotating it as indicated. Unlock Direction: Unfasten the propeller by rotating is as indicated. NOTE:
Power off the aircraft before attaching or detaching propellers. Propellers must be undamaged and firmly attached. 8 9.PREPARING THE CONTROLLER
(1) Unfold the antenna, detach the stick heads on the back of the controller handle, and screw them into the corresponding screw holes on both sides of the screen.
(2) Adjust the antenna angle, and when the antenna and the back of the controller are at the angle of 180 or 260, and the antenna surface is facing the aircraft, the signal quality of the aircraft and controller will reach the optimal condition. o 100 10. POWERING UP Press and hold the power button for
(1) 2 seconds to turn on the controller. 9 Press and hold the power button 3 seconds to turn on the aircraft.The
(2) current battery level will be clearly displayed. 11. TAKE OFF Start the motors by holding both command sticks for two seconds as
(1) shown below. or Push the left command stick slowly upward.
(2) NOTE:
The default control stick mode is mode 2. The left stick controls the altitude and heading of the aircraft, while the right stick controls the forward, backward and sideward movements. Before takeoff, place aircraft on a level surface, stand well clear of the rear of the aircraft. 10 12. COMMAND STICK CONTROLS(MODE 2) Left Command Stick Left Side View Left Side View Ascend Descend Upward Downward Top View Top View Nose Rotates Left Nose Rotates Right Move Left Move Right Right Command Stick Left Side View Left Side View Forward Backward Upward Downward Rear View Rear View Left Right Move Left Move Right 11 13. SPECIFICATIONS Aircraft Operating Frequency Transmission Power (EIRP) Remote Controller Operating Frequency 902~928MHz (FCC);
2.4~2.4835GHz;
5.725~5.850GHz (Non-Japan);
5.650-5.755GHz (Japan) 900MHz:
FCC/ISED<=31dBm 2.4GHz:
FCC/ISED<=32dBm;
CE/MIC/SRRC/RCM<=20dBm 5.8GHz/5.7GHz:
FCC/ISED/SRRC/MIC<=33dBm;
CE/RCM<=14dBm 902~928MHz (FCC);
2.4~2.4835GHz;
5.725~5.850GHz (Non-Japan);
5.650-5.755GHz (Japan) FCC: 33dBm Transmission Power (EIRP) CE: 20dBm@2.4G, 14dBm@5.8G/5.7G SRRC: 20dBm@2.4G, 33dBm@5.8G/5.7G 12 FCC and ISED Canada Compliance This device complies with part 15 of the FCC Rules and ISED Canada licence-exempt RSS standards. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dISED Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 13 Aircraft RF Exposure Information This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be operated with minimum distance 20cm between the radiator and your body. Remote Controller FCC Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model device is an available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations
(e.g. at the ear and worn on the body) as required by the FCC. For limb worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal. For body worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the device a minimum of 10mm from the body. ISED Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model device is an available for sale to the public, it must be tested and certified to the ISEDC that it does not exceed the exposure limit established by the ISEDC, Tests for each device are performed in positions and locations (e.g. at the ear and worn on the body)as required by the ISEDC. For limb worn operation, this device has been tested and meets the ISEDCRF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal. 14 For body worn operation, this device has been tested and meets the ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the device a minimum of 10mm from the body. Tauxdabsorptionspcifique (SAR) informations les tests SAR sonteffectus en utilisant les positions oprationnellesnormalisesaccept espar la ISEDC, le dispositifmettant son niveau de puissance certifi le plus levdanstoutes les bandesdefrquencestestes.Avantquun nouveau modle de dispositif ne soitdisponible la vente aupublic, ildoittretest et certifi la ISEDC quil ne dpasse pas la limitedexpositiontablieparla ISEDC, les Tests pour chaquedispositifsonteffectusdans des positions et des emplacements(par exemple loreille et portsur le corps) commelexige la ISEDC. Pour le fonctionnement desmembresuss, cetappareil a ttest et rpond aux lignesdirectricesdexposition aux RF ISEDClorsquilestutilis avec un accessoiredsign pour ceproduitoulorsquilestutilis avec unaccessoire qui ne contient pas de mtal. Pour le fonctionnement du corps us, cetappareil a ttest et rpond aux lignesdirectricesdexposition RF ISEDC lorsquilestutilis avec un accessoiredsign pour ceproduitoulorsquilestutilis avec un accessoire qui ne contient pas de mtal etqui positionnecet appareil au moins 10mm du corps. EU/UK Compliance Autel Robotics Co., Ltd. hereby declares that this wireless device is in compliance with Directive 2014/53/EU and Radio Equipment Regulations 2017. 18th Floor, Block C1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan District, Shenzhen, Guangdong, 518055, China 22522 29th Dr SE, Ste 101 Bothell, WA 98021 United States Toll-free: (844) MY AUTEL or (844) 692-8835 www.autelrobotics.com 2022 Autel Robotics Co., Ltd. All Rights Reserved 15 www.autelrobotics.com 2022 Autel Robotics Co., Ltd. All Rights Reserved 16 FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The distance between user and products should be no less than 20cm Ce dispositif est conforme aux normes autoriser-exemptes du Canada RSS d'industrie L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.Cet quipement est conforme avec l'exposition aux radiations IC dfinies pour un environnement non contrl. L'utilisateur final doit respecter les instructions de fonctionnement spcifiques pour satisfaire la conformit aux expositions RF. Cet metteur ne doit pas tre co-localises Cet appareil a t test pour des oprations ports sur le corps typiques. Pour se conformer 1 aux exigences d'exposition aux radiofrquences, une distance minimale de 30cm doit tre maintenue entre le corps de l'utilisateur et le combin, y compris l'antenne. Les pinces de ceinture, les tuis et autres accessoires similaires utiliss par cet appareil ne doivent pas contenir de composants mtalliques. Les accessoires portatifs qui ne rpondent pas ces exigences peuvent ne pas se conformer aux exigences d'exposition RF et doit tre vite. Utilisez uniquement l'antenne fournie ou une antenne approuve 2