FCC ID: X4K-ATS3DCB11WS DOMINATOR SYNCRO Overhead Garage Door Operator

Overhead Garage Door Operator Dominator Tempo & Syncro Instruction Manual Conforms to:

4008033 ANSI/CAN/UL325 Tested to comply with Part 15 of the FCC Rules SYNCRO ATS-3 DOMINATOR TEMPO ATS-2AM SECTIONAL DOOR OPENER SYNCRO ATS-3 DOMINATOR SYNCRO ATS-3AM SMART SECTIONAL DOOR OPENER FOR RESIDENTIAL USE ONLY Doc # 160416_00 Part # 87406 Released 11/03/21 CONTENTS Overhead Garage Door Operator 6.2.4 Securing the Powerhead Perforated Angle or equivalent 11 7.1.1 To Operate the opener:

1. System Specifications 2. Safety Information 3. Operating controls 4. Kit Contents 5. Operator Safety & Security 5.1 Manual Door Operation 5.2 Emergency Evacuations 5.3 Power Failure 5.4 Re-Engaging the Operator 5.5 Security - Inbuilt Locking Facility 6. Installation Instructions 6.1 C-Rail Assembly 6.2 Mounting Operator for a Track Type Door 6.2.1 Determine Bracket Position 6.2.2 Mounting the Wall Bracket 6.2.3 Attach the C-Rail to the Wall Bracket 6.2.6 Mounting Door Bracket 6.2.7 Attaching the Arms 6.3 Safety Beam Installation 6.3.1 Safety Infra-Red Beam Kit (P/N 62047) 6.3.2 Assembling the Mounting Bracket 6.3.3 PE Assist Alignment 6.4 Setting Speed and Limits 6.4.1 Set the Limit Positions and adjust drive speed:

6.4.2 Clearing the Door Limit Positions 6.4.3 Re-profiling the Door 6.5 Safety Testing 6.5.1 Obstruction Detection Test 6.5.2 Test the Close Cycle and Safety Reversal 6.5.3 Testing the Open Cycle 6.5.4 Test the Manual Door Operation 6.6 Coding Premium Remote Controls 6.6.1 Setting Remote Control Functions 6.6.2 Erasing All Premium Remote Control Codes 6.6.3 Vacation Mode 6.6.4 Remotely Coding Premium Remote Controls 6.6.5 Install Premium Wall Control 6.7 Battery Backup 6.7.1 Connecting the Battery Backup 6.7.2 Test the Opener 6.7.3 LED Battery indicator 6.8 Accessories 6.8.1 Terminal Block 6.9 Auto-Ki Smart Phone Control 6.10 Auto-Close 6.11 Attach Warning Labels 6.12 Homelink 6.8.2 Connecting or Disconnecting Accessories 6.12.1 Coding in the HomeLink button 6.12.2 Coding HomeLink button into the Operator 6.12.3 Erasing all HomeLink buttons from Operator 7. Operation Instructions 7.1 How to Use Your Operator 7.1.2 Replacing the Battery: 3V Lithium Battery CR2032. 7.2 User Operating Controls 7.3. Troubleshooting 7.4. Service / Warning Indicator 7.4.1 Main Light = Service / Warning Indicator:

7.4.2 Main Light = FAULT Status Indicator (when MODE is on): 28 7.4.3 Connecting or Disconnecting Accessories:

7.5 Disposal of Batteries 8. User Maintenance Instruction 8.1 Door Maintenance 8.2 If You Need a Service Call 9. Appendix A - Status Indication during Operating Mode. B - Adjustment Mode Instructions C - Adjusting Force Margins D - Battery Functions E - Setting up Tilt Door F - Setting the PET Mode position G - Setting limits via Premium Remote Control 19 19 19 19 19 19 19 20 22 22 23 23 23 23 24 25 25 25 26 27 28 28 28 29 30 30 30 31 31 32 33 33 33 34 34 3 4 6 7 8 8 8 8 8 8 9 10 10 10 10 10 11 12 13 13 13 13 14 14 14 14 15 15 15 15 15 16 16 18 18 18 18 2 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 1. System Specifications Factory Default Settings Default Maximum Maximum motor run time 1 Minute Courtesy light time 180 secs Obstruction force margin 1.0A Auto close time 0 seconds Technical Specifications

240 secs 2.0A 120secs Model Input Voltage Current (Max) Transformer secondary output Voltage Motor type SYNCRO ATS-3AMB SYNCRO ATS-3AM TEMPO ATS-2AMB TEMPO ATS-2AM 120V / 60Hz 120V / 60Hz 120V / 60Hz 120V / 60Hz 2.0A 24Vac 2.0A 24Vac 2.0A 24Vac 2.0A 24Vac 24Vdc geared motor with permanent magnet 24Vdc geared motor with permanent magnet 24Vdc geared motor with permanent magnet 24Vdc geared motor with permanent magnet Shuttle travel distance in the C-Rail 9.19ft (2.8m) approximately (standard) 9.19ft (2.8m) approximately (standard) 9.19ft (2.8m) approximately (standard) 9.19ft (2.8m) approximately (standard) Maximum shuttle travel distance in the C-Rail 16.4ft (5m) (with extended C-Rail) 16.4ft (5m) (with extended C-Rail) 16.4ft (5m) (with extended C-Rail) 16.4ft (5m) (with extended C-Rail) Peak Short Term Pulling Force 1000N 1000N 1000N 1000N Maximum door hanging weight 520lbs (236kg) 520lbs (236kg) 440lbs (200kg) 440lbs (200kg) Receiver type UHF Multifrequency FM-

Receiver UHF Multifrequency FM-

Receiver UHF Multifrequency FM-

Receiver UHF Multifrequency FM-

Receiver Receiver code storage capacity 64 x 4 button transmitter codes 64 x 4 button transmitter codes 64 x 4 button transmitter codes 64 x 4 button transmitter codes Coding type TrioCode128 TrioCode128 TrioCode128 TrioCode128 Number of code combinations Over 4.29 billion random codes Over 4.29 billion random codes Over 4.29 billion random codes Over 4.29 billion random codes Code generation Nonlinear encryption algorithm Nonlinear encryption algorithm Nonlinear encryption algorithm Nonlinear encryption algorithm Remote control battery CR2032 3 Volts CR2032 3 Volts CR2032 3 Volts CR2032 3 Volts Courtesy light 2 LED Modules 2 LED Modules 2 LED Modules 2 LED Modules Control board fuse 10A (slow blow) 10A (slow blow) 10A (slow blow) 10A (slow blow) Battery backup Network connectivity 2 x 12PCA 1.3 - 12V1.3 AH Batteries Battery compatible,

(requires optional Battery Backup kit) 2 x 12PCA 1.3 - 12V1.3 AH Batteries Battery compatible,

(requires optional Battery Backup kit) Network ready, Smart hub already installed Network ready, Smart hub already installed Network compatible,

(requires optional Auto-Ki Control Kit) Network compatible,

(requires optional Auto-Ki Control Kit) NOTE: Intermittent operations may occur in areas which experience very strong winds. The strong wind puts extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system intermittently. 3 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 2. Safety Information WARNING! It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference. This operator should be installed in accordance with relevant US and Canada Standards. To reduce the risk of injury to persons Use this operator only with a sectional door. DO NOT install product on J-Type or Single Piece Doors.. This operator is not suitable for commercial, industrial or common entry applications. This operator is a plug in domestic appliance and is designed for indoor use only. It must be installed in a dry position that is protected from the weather. Door must have Safety Beams fitted. Activate the operator only when the garage door is in full view, free of obstructions and with the operator properly adjusted. The network device allows for operation of the door when not in line-

of-sight of the door and operator. Therefore the door may operate unexpectedly, therefore do not allow anything to stay in or near the path of the door. Watch the moving door and keep people away until the door is completely opened or closed. ELECTROCUTION: To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. This operator is not equipped for permanent wiring. Contact a qualified electrician to install a suitable receptacle if one is not available. Installation and wiring must be in compliance with your local building and electrical codes. This operator is not equipped for permanent wiring. Contact a qualified electrician to install a suitable receptacle if one is not available. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard. Connect the power cord only to properly earthed mains. If an extension lead must be used, make sure it is a 3-core lead and approved to 7 amp capacity. This unit is not user serviceable. Unplug the power cord before removing the cover. Ensure that the power cord is attached clear of all moving parts. Ignoring these instructions can cause electric shock. 4 Please read these important safety rules These safety READ THESE INSTRUCTIONS CAREFULLY. alert property safety or symbols damage indicate instruction a personal exists. This automatic garage door operator is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules. Failure to comply with the installation instructions and the safety warnings may result in death, serious personal injury and/or property damage. CAUTION:

If your garage has no pedestrian entrance door, an emergency access device should be installed. This accessory allows manual operation of the garage door from outside in case of power failure. Keep the garage door balanced. Sticking or binding doors must be repaired. Garage doors, door springs, brackets and their hardware are under extreme tension and can cause serious personal injury. Do not attempt any garage door adjustment. Do not use if repair or adjustment is needed. Call for professional garage door service. Position the Garage Door Operator so that the power plug is accessible when inserted into the power outlet. Install the wall transmitter in a location where the garage door is visible, but out of the reach of children at a height of at least 5 feet

(1.53m). To avoid serious personal injury from entanglement, remove all unnecessary ropes or chains and disable any equipment such as locks which are not needed for powered operation. Do not wear rings, watches or loose clothing while installing or servicing a garage door operator. Ensure ladder is the correct type for the job and is on flat ground. We recommend the user has 3 points of contact while on ladder. Activate the operator only when the garage door is in full view, free of obstructions and with the operator properly adjusted. The operator is not intended for use by young children or infirm persons without supervision. Keep transmitters away from children. Do not allow children to play with door controls. ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual Please read these important safety rules 2. Scurit AVERTISSEMENT ! pour la scurit des usagers, il est essentiel de suivre toutes les instructions. Le non- respect des instructions dinstallation et des avertissements de scurit peut causer de graves blessures et/ou endommager lappareil et la tlcommande. Conservez ces instructions en lieu sr. Cet appareil doit tre install conformment aux normes US et canadiennes en vigueur. Pour rduire le risque de blessure corporelle, utilisez cet appareil uniquement avec une porte de section. Ninstallez PAS le produit sur des portes de type J ou monobloc. Cet appareil est un accessoire domestique conu pour tre utilis uniquement l'intrieur. Il doit tre install au sec et l'abri des intempries. Lisez attentivement ces rgles de scurit. pictogrammes une Ces de les personnes ou LISEZ CES INSTRUCTIONS ATTENTIVEMENT. scurit pour indiquent consigne les biens. Cette commande automatique pour porte de garage est conue et teste pour fonctionner en toute scurit. Pour ce faire, elle doit tre installe et utilise dans le strict respect des rgles de scurit suivantes. Le non-respect des instructions d'installation et des avertissements prsent un risque de mort, de blessure grave et/ou de prjudice pour les biens. La porte doit tre quipe de faisceaux de scurit. Activez l'appareil uniquement lorsque la porte du garage est la vue, exempte d'obstacles et avec l'appareil bien rgl. PRUDENCE:

La tlcommande radio permet dactionner la porte lorsque lutilisateur est hors de la ligne de vue de la porte et de lappareil. En consquence, la porte risque de souvrir ou se fermer inopinment et vous devez viter de laisser des objets sur sa course ou proximit. Suivez la porte pendant l'ouverture ou la fermeture, et veillez ce que personne ne se trouve proximit tant qu'elle n'est pas compltement ouverte ou ferme. LECTROCUTION: Pour rduire les risques dlectrocution, cet appareil est quip dune fiche avec broche de mise la terre. Cette fiche ne peut tre branche que dans une prise avec mise la terre. Sil nest pas possible de la brancher dans la prise, faites poser une prise approprie par un lectricien qualifi. Ne pas modifier la fiche. Ce matriel est pas quip pour le cblage permanent. En labsence de rceptacle appropri, contactez un lectricien qualifi pour en installer un. L'installation et le cblage doivent tre effectus conformment aux codes de la construction et de l'lectricit en vigueur. Cet appareil nest pas quip pour un cblage permanent. En labsence de rceptacle, contactez un lectricien qualifi pour en installer un. Si le cordon lectrique est abm, il doit tre remplac par le fabricant, son SAV agr ou un technicien qualifi. Branchez le cordon lectrique uniquement une prise secteur dment relie la terre. Si vous devez utiliser une rallonge, assurez-

vous qu'elle est tripolaire et d'une capacit de 7ampres. Cet appareil n'est pas rparable par l'utilisateur. Avant de retirer le capot, dbranchez le cordon lectrique. Assurez-vous qu'il ne risque pas d'entrer en contact avec des pices en mouvement. Le non-respect de ces instructions peut avoir une lectrocution pour consquence. Si votre garage ne comporte pas de porte pour pitons, il convient d'installer un dispositif d'accs d'urgence. Cet accessoire permet d'actionner la porte de garage manuellement de l'extrieur en cas de panne d'lectricit. Veillez ce que la porte du garage soit bien quilibre. Si une porte reste colle ou qu'elle accroche, elle doit tre rpare. Les portes de garage, les ressorts de porte, les pattes de fixation et les lments matriels sont soumis une tension extrme et peuvent blesser gravement. Ne tentez pas de rgler la porte de garage par vous-mme. Ne l'utilisez pas si une rparation ou un rglage est ncessaire. Faites appel un technicien spcialis. Positionnez le dispositif de commande de manire ce que la prise de courant soit accessible lorsqu'elle est branche. Installez l'metteur mural un emplacement o la porte du garage est visible, mais hors de porte des enfants, une hauteur d'au moins 1,50m. Rangez cordes et chanes pour viter de vous blesser, et dsactivez les serrures et autres quipements qui ne sont pas ncessaires pour une utilisation sous tension. Pendant l'installation ou la rparation d'un dispositif de commande de porte de garage, retirez bijoux et montre, et attachez vos vtements. Utilisez un escabeau adquat et stable. Lorsque l'utilisateur se tient sur un escabeau, il est conseill de veiller ce que les points de contact soient au nombre de trois. Activez l'appareil uniquement lorsque la porte du garage est la vue, exempte d'obstacles et avec l'appareil bien rgl. L'appareil ne doit pas tre utilis sans supervision par de jeunes enfants ou des personnes infirmes. Les metteurs doivent rester hors de porte des enfants. N'autorisez pas les enfants jouer avec les commandes de porte. 5 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 3. Operating controls Button Function 1. DOWN ARROW (Blue) Closes the door 3. STOP (Red) Stops the door 4. UP ARROW (Green) Opens the door 2. DOWN ARROW LED (Blue) Illuminates when the door is closed and flashes when the door is closing, obstructed on close or stopped. 5. UP ARROW LED (Green) Illuminates when the door is open and flashes when the door is opening, open with the auto-close timer running, obstructed on opening or stopped. 6. MODE (Yellow) Enables Load Diagnostics Mode 7. MODE STATUS LED (Yellow) Illuminates when in Diagnostics Mode 8. BATTERY STATUS LED (Yellow) Illuminates when battery is charged and flashes when battery is charging, in use or battery failed. 9. REMOTE CONTROL STATUS LED (Red) Flashes on remote lockout and flickers on remote control activity 10. ADJUSTMENT LED (Yellow) Flashes a certain number of times depending on the parameter being changed. 11. NETWORK LED

( ATS-3 Only) Is a dual colour LED. Illuminates purple when hot spot active, blue when connected to cloud and red when in production mode. Flashes different colour depending on the activity. 01 02 03 04 05 06 07 Fig.3.1 11 10 09 08 6 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 4. Kit Contents 6 4 7 8 5 16 9 12 10 13 11 14 15 2 17 Fig.4.1 3A 3B 1 1. 1 x ATS drive unit 2. 1 x Premium Wall Control kit 3. (A) 2 x Premium Remote Control

(B) 1 x Homelink Transmitter 4. 1 x Bent arm door attachment 5. 1 x Straight arm door attachment 6. 1 x Wall bracket TS01 7. 1 x Door bracket Locator 8. 1 x Door bracket 9. 3 x Pin Snap SSP 8 ZNU 31080 10. 2 x Hex Head screw M8x25 11. 1 x Pin 0890 12. 2 x Clevis Pin 0829 13. 2 x Hex Serration flange nut M8 14. 4 x Hex flange screw taptite S M4 x 10 15. 1 x Wired Safety Beam kit PLUS 16. 2 x Track Bracket 17. 1 x Pre-Assembled C-Rail NOTE: Chain/belt in one piece rail has been tensioned by the factory. Do not adjust the tension of the chain/timing belt. IMPORTANT NOTE: If modification to the track length required, adjustment must be made only from power head end. 9 6 11 9 12 5 D O O R S H I G H E S T P O I N T 3374mm 3156mm*

17 MINIMUM HEAD ROOM FOR STEEL RAIL 57mm 13 10 9 12 4 10.00 min 7 8 Rail no Extension Kit 3156mm Rail + 1 Extension Kit 3946mm Rail + 2 Extension Kits 4736mm

* Rail refers to 3160 rail 15 Placed on both sides of door, 5 above floor level 16 14 1 Perforated Angle 353mm 1 5 0 m m 7 Fig.4.2 1 7 0 m m Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 5. Operator Safety & Security MANUAL RELEASE WARNING! When operating the manual release (while the door is open) the door may fall rapidly due to weak or broken springs, or due to being improperly balanced. Do not disengage the operator to manual operation with children/persons or any objects including motor vehicles within the doorway. IN THE EVENT THE DOOR BECOMES OBSTRUCTED DETACH DOOR FROM OPERATOR AS FOLLOWS:

SI LA PORTE EST BLOQUE, DTACHEZ-LA DU DISPOSITIF DE COMMANDE EN PROCDANT COMME SUIT :

DOOR TO DISENGAGE PULL HANDLE TOWARDS DOOR AND RELEASE POUR DBLOQUER, TIREZ LA POIGNE VERS LA PORTE PUIS RELCHEZ ENGAGE POSITION ENGAGEZ LA POSITION DISENGAGE POSITION DSENGAGEZ LA POSITION TO RE-ENGAGE PULL HANDLE AWAY FROM DOOR AND RELEASE POUR LA RENGAGER, TIREZ SUR LA POIGNE EN LOIGNANT DE LA PORTE PUIS RELCHEZ AVERTISSEMENT : Lorsque vous utilisez le dclenchement manuel (alors que la porte est ouverte), la porte peut tomber rapidement si les ressorts sont fatigus ou briss, ou parce qu'elle est mal quilibre. NE PAS dsengager loprateur en mode manuel lorsque des enfants/personnes, ou des objets tels que des vhicules moteur, sont dans le passage. DBLOCAGE MANUEL Fig. 5.1 5.1 Manual Door Operation To disengage the operator from the door (preferably with the door in the closed position), pull down on the string handle on an angle towards the door

(Fig 5.1). This will allow you to manually open or close the door. CAUTION: Do not use the string handle as a mechanism to open the door. Failure to comply may cause serious injury. ATTENTION: Ne pas utiliser la poigne de chane pour ouvrir la porte. Le non-respect de cette consigne peut provoquer des blessures graves. To re-engage the operator pull the string handle away from the door -

see Re-Engaging the Operator. 5.2 Emergency Evacuations In emergencies the garage door can be disengaged from the operator, via the manual release cord and the door opened manually. The manual release cord should be a maximum of 1.8m from the ground. The cord can be adjusted for special considerations. 5.3 Power Failure When there is a power failure, the operator will be unable to automatically open or close your garage door. To use your door whilst there is no power you will need to disengage the operator and use the door manually see 5.1 Manual Door Operation. 5.4 Re-Engaging the Operator When the door has been disengaged from the opener, the shuttle assembly, attached to the manual release cord, can move up and down the chain. Re-engage the opener (Fig 5.1) (preferably with the door open to waist height) and then press the programmed transmitter button, the motor will run until the shuttle assembly engages the chain index on the chain, you will hear it click into place. Then the door will operate as normal. 5.5 Security - Inbuilt Locking Facility DO NOT lock your door when your operator is engaged as it has inbuilt locking facility. With the opener engaged your door will be locked whether the power is on or off. CAUTION: When the operator is manually disengaged, the door is no longer locked. To lock the door manually, re-engage the operator after the door is closed.

: Quand le dispositif est dsengag ATTENTION manuellement, la porte nest plus verrouille. Pour verrouiller la porte manuellement, rengager le dispositif une fois la porte ferme. 8 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6. Installation Instructions IMPORTANT INSTALLATION INSTRUCTIONS WARNING! TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:

(1) READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

(2) INSTALL ONLY ON A PROPERLY OPERATING AND BALANCED GARAGE DOOR. AN IMPROPERLY BALANCED DOOR HAS THE POTENTIAL TO INFLICT SEVERE INJURY. HAV E A QUALIFIED SERVICE PERSON MAKE REPAIRS TO CABLES, SPRING ASSEMBLIES, AND OTHER HARDWARE BEFORE INSTALLING THE OPENER.

(3) REMOVE ALL PULL ROPES AND REMOVE, OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR BEFORE INSTALLING OPENER.

(4) WHERE POSSIBLE, INSTALL THE DOOR OPENER 7 FEET OR MORE ABOVE THE FLOOR. FOR PRODUCTS HAVING AN EMERGENCY RELEASE, MOUNT THE EMERGENCY RELEASE WITHIN REACH BUT AT LEAST 6 FEET ABOVE THE FLOOR AND AVOIDING CONTACT WITH VEHICLES TO AVOID ACCIDENTAL RELEASE.

(5) DO NOT CONNECT THE OPENER TO SOURCE OF POWER UNTIL INSTRUCTED TO DO SO.

(6) LOCATE THE CONTROL BUTTON:

(I) WITHIN SIGHT OF DOOR,

(II) AT A MINIMUM HEIGHT OF 5 FEET ABOVE FLOORS, LANDINGS, STEPS OR ANY OTHER ADJACENT WALKING SURFACE SO SMALL CHILDREN ARE NOT ABLE TO REACH IT, AND

(III) AWAY FROM ALL MOVING PARTS OF THE DOOR.

(7) INSTALL THE ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL BUTTON IN A PROMINENT LOCATION. INSTALL THE EMERGENCY RELEASE MARKING. ATTACH THE MARKING ON OR NEXT TO THE EMERGENCY RELEASE.

(8) AFTER INSTALLING THE OPENER, THE DOOR MUST REVERSE WITHIN 2 SECONDS WHEN IT CONTACTS A 1 1/2 -INCH HIGH OBJECT (OR A 2 BY 4 BOARD LAID FLAT) ON THE FLOOR.

(9) FOR PRODUCTS HAVING A MANUAL RELEASE, INSTRUCT THE END USER ON THE OPERATION OF THE MANUAL RELEASE. AVERTISSEMENT -

POUR RDUIRE LES RISQUES DE BLESSURES GRAVES OU DE MORT:

(1) LISEZ CETTE NOTICE ET CONFORMEZ-VOUS AUX INSTRUCTIONS.

(2) NE POSEZ CET OUVRE-PORTE QUE SUR UNE PORTE DE GARAGE CORRECTEMENT QUILIBRE. UNE PORTE MAL QUILIBRE PEUT CAUSER DES BLESSURES GRAVES. CONFIEZ LA RPARATION DES CABLES, DES RESSORTS ET DE TOUT AUTRE LMENT UN TECHNICIEN QUALIFI AVANT DENTREPRENDRE LINSTALLATION.

(3) ENLEVEZ LES CORDES ET ENLEVEZ OU NEUTRALISEZ TOUT DISPOSITIF DE VERROUILLAGE SOLIDAIRE DE LA PORTE DE GARAGE AVANT LINSTALLATION.

(4) DANS LA MESURE DU POSSIBLE, INSTALLEZ LOUVRE-PORTE AU MOINS (7 PI) DU SOL. POSEZ LE DISPOSITIF DE DESACCOUPLEMENT DURGENCE AU MOINS (6 PI) DU SOL EN EVITANT LE CONTACT AVEC DES VEHICULES POUR EVITER TOUT DECLENCHEMENT ACCIDENTEL.

(5) NE BRANCHEZ PAS LOUVRE-PORTE AVANT DY ETRE AUTORISE PAR LA NOTICE.

(6) INSTALLEZ LE BOUTON DE COMMANDE:

(i) A UN ENDROIT QUE LON PEUT VOIR DE LEMBRASURE DE LA PORTE;

(ii) UNE HAUTEUR MINIMALE DE 1.5 M (5 PI) DU SOL - AFIN QUE LES JEUNES ENFANTS NE PUISSENT PAS LATTEINDRE; ET

(iii) L'CART DES PIECES MOBILES DE LA PORTE.

(7) APPOSEZ LETIQUETTE DE MISE EN GARDE RELATIVE AU DANGER DE HAPPEMENT A PROXIMIT DU BOUTON DE COMMANDE ET LETIQUETTE RELATIVE AU REGLAGE DE LA COMMANDE A UN EMPLACEMENT EN EVIDENCE

- PAR EXEMPLE SUR LA PAROI INTERIEURE DE LA PORTE DE GARAGE OU SELON LES INSTRUCTIONS DE LE NOTICE DINSTALLATION.. APPOSEZ LETIQUETTE RELATIVE AU DESACCOUPLEMENT DURGENCE SUR LE DISPOSITIF OU A PROXIMITE DE CE DERNIER.

(8) UNE FOIS LOU VRE-PORTE INSTALLE, LE SENS DE LA COURSE DOIT SINVERSER LORSQUE LA PORTE ENTRE EN CONTACT AVEC UN OBJET DUNE HAUTEUR DE 38 MM (1 PO) (OU UN MADRIER DE 2 X 4 PO DE SECTION, PLAT ) POSE SUR LE SOL.

(9) POUR LES PRODUITS MUNIS DUN DISPOSITIF DE DESACCOUPLEMENT MANUEL, INDIQUEZ A LUTILISATEUR FINAL LA PROCEDURE DUTILISATION DU DISPOSITIF. 9 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.1 C-Rail Assembly 6.1.1 Installing the C-Rail a. Remove the Opener from the box. b. Locate and insert the shaft of drive unit 1 into the C-Rails sprocket as shown in c. Fix the two track brackets 16 with four (4) M4 x 8 screws 14 supplied in accessory Fig 6.1. pack (Fig 6.1.2). d. Place drive unit back in packing box for protection. 1 14 16 This operator is ELECTROCUTION!

not equipped for permanent wiring. Contact a qualified electrician to install a suitable receptacle if one is not available. AVERTISSEMENT! Ce dispositif douverture nest pas conu pour un cblage permanent. labsence de rceptacle appropri, En contactez un lectricien qualifi pour en installer un. Fig. 6.1.1 Fig.6.1.2 17 Locate shaft the sprocket into 6.2 Mounting Operator for a Track Type Door WARNING! To reduce the risk of injury to persons -

Use this operator only with a sectional door. AVERTISSEMENT! Pour rduire les risques de blessure, utilisez ce dispositif douverture uniquement avec une porte sectionnelle. 6.2.1 Determine Bracket Position a. Determine the centre of the door and mark this point with a line on the wall above. b. Raise the door and find the highest point of travel of the first (top) door panel. c. Using step ladder and a level, transfer this height to the wall above the door and mark a line 2.36(60mm) above it, across the centre line (Fig.6.2.1). 6.2.2 Mounting the Wall Bracket d. Draw two lines extending 0.846 (21.5mm) from each side of the centre point

(Fig.6.2.2). e. Centre the wall bracket 6 over the intersection of these two lines. Mark centres for at least two holes and ensure it is into a solid mounting point. f. Drill holes in the wall with an appropriate bit. g. Secure to the wall using:

(i) IF CONCRETE OR BRICK:

5/6 (8mm) loxins/dynabolts.

(ii) IF TIMBER:

wood screw #20 or similar (minimum 1.97 50mm long) (Fig.6.2.2). WARNING!: Make sure concrete, brick wall or timber lintels are solid and sound so as to form a secure mounting platform. 6.2.3 Attach the C-Rail to the Wall Bracket a. Leave the drive unit in its packing box on the floor for protection and lift the other end of the C-Rail. b. Attach the C-Rail assembly 17 to the wall bracket 6 with the 10 3.54 (90mm) long pin 11 and secure with the supplied pin snap 9 (Fig.6.2.3). 11 6 60mm Level Fig.6.2.1 Fig.6.2.2 6 Fig.6.2.3 17 9 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6.2 Mounting Operator for a Track Type Door Fig.6.2.4 Fig.6.2.5 Ceiling Beams that run towards the door requires:

1 x perforated L shape metal strip and 2 x shorter perforate L shape metal drop down strips. Ceiling Beams that run parallel to the door requires:

2 x perforated L shape metal strips and 2 x shorter perforate L shape metal drop down strips. tip Straighten the antenna on the opener, by pulling straight down to ensure optimal reception. Fig.6.2.6 7 8 6.2.4 Securing the Powerhead Perforated Angle or equivalent a. Measure across the ceiling from the centre point 10.3 ft (+/- 2) to find a supporting beam. b. Create a perforated angle which best suits your site. Use a hack saw to cut the L shape metal strips. Secure the perforated angle to a supporting beam using diagrams shown below (Fig.6.2.4 & Fig.6.2.5). c. Raise the drive unit to the ceiling mounted perforated angle and secure with 51/64 screws and nuts (not supplied). Strips should not extend more than 0.708 (18mm) below centre of drive unit mounting holes. d. To prevent moisture on the C-rail running into the powerhead it is recommended a strip of silicon sealant is placed across the top of the C-rail just before the opener. WARNING! The operator must be securely fastened to a structural support of the garage. Failure to fasten the operator correctly may lead to operator failure causing serious personal injury and/or property damage. AVERTISSEMENT ! Le dispositif douverture doit tre solidement fix un support structurel du garage. Sinon, les utilisateurs risquent de se blesser ou le matriel de sabmer. ELECTROCUTION! This operator is not equipped for permanent wiring. Contact a qualified electrician to install a suitable receptacle if one is not available. AVERTISSEMENT! Ce dispositif douverture nest pas conu pour un cblage permanent. En labsence de rceptacle appropri, contactez un lectricien qualifi pour en installer un. 6.2.6 Mounting Door Bracket a. The door bracket locator 7 is placed over the door bracket 8 , on the doors centre line one-third down the top panel and mounted using 1/4 or equivalent screws (not supplied) (Fig 6.2.6), b. STEEL DOORS ONLY: Bracket can be welded in place. NOTE: As various types of doors exist, if in doubt about the strength of the door, reinforcement may need to be added to the frame of the door panel where necessary. Damage to the door panel may occur if the bracket is installed incorrectly on a panel with insufficient strength. The door operator warranty does not cover damage caused by the operator to the door and/

or door panel. REMARQUE: tant donn quil existe divers types de porte, il est possible dajouter un renfort au cadre du panneau en cas de doute quant sa solidit. Le panneau de porte peut tre endommag si la patte de support est mal fixe et sil est insuffisamment rigide. La garantie du dispositif douverture de la porte ne couvre pas les dommages causs la porte et/ou au panneau par le dispositif douverture. 11 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.2 Mounting Operator for a Track Type Door 6.2.7 Attaching the Arms a. Assemble the bent arm 4 (connecting to the door) to the right side of the straight arm 5 with bolts 10 and nuts 13 supplied in the accessory pack. Connect the straight arm 5 to the shuttle with a clevis pin 12 and a pin snap 9 . Always use both bent and straight arms (Fig 6.2.7). b. Connect the assembled arm to the bracket with clevis pin 12 and pin snap 9 . The angle A must be more than 10. WARNING! connecting the bent arm other way around may damage the door. AVERTISSEMENT! Si vous fixez le bras coud lenvers, vous risquez dendommager la porte. 9 4 9 6 12 13 5 Fig.6.2.7 10 A 12 7 8 IMPORTANT NOTE: If the manual release handle is more than 5.91ft (1.8 meters) from floor level when the operator is installed, extend the handle to a height 5.91ft (1.8 meters). IMPORTANT: Si la poigne de dverrouillage manuel est plus de 1,80m (5,91) de hauteur quand le dispositif douverture est install, la poigne doit tre place 1,80m (5.91) de hauteur. 12 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6.3 Safety Beam Installation IMPORTANT NOTE: The Safety Beam must be installed and connected before the travel limits are set. IMPORTANT : Le faisceau de scurit doit tre install et connect avant de dfinir les fins de course. 6.3.1 Safety Infra-Red Beam Kit (P/N 62047) A Safety Beam extends across the door opening. This Safety Beam is designed to detect an obstruction while the door is closing and to send a signal to the door operator to reverse or stop the door movement. Install the Safety Beam indoor only. 6.3.2 Assembling the Mounting Bracket a. Place the round screw 3 through the Bracket 5 . Attatch the Safety Beam Transmitter (TX) using four (4) M3 x 5 Taptite screws 4

(Fig. 6.3.1). b. Connect the mounting bracket 2 to the Bracket 5 using the wing nut 8 onto the round screw 3 . Secure the adjustment bracket 6 to the mounting bracket 2 using two (2) screws 3 and nuts 7 . c. Repeat steps (a) and (b) to assemble the Safety Beam Receiver (RX). d. Locate the Safety Beam in a strategic location in the door opening. We recommend that the sensor is placed no higher than 6 and no lower than 5above the floor level. The mounting surface should be rigid. 6.3.3 PE Assist Alignment a. Wire the PE Beams as per Wiring Diargram (Fig. 6.3.2). b. Remove the glass protectors from both the Transmitter and Receiver. c. After the beams are installed the beam alignment feature of the opener can be used. d. Turn power on to the opener. e. Align the safety beams by moving them per Fig 6.3.3 and using the main light as a guide:

(i) bright = aligned

(ii) dull = not aligned or blocked When the beams are aligned, continue with Setting Limits. WARNING: When the Safety Beam is fitted, the doorway must be clear of all obstructions and persons at all times. Incorrect location of the safety beams may not give safety protection at all times. Check to make sure that the height of the beam gives maximum protection. AVERTISSEMENT : Lorsque le faisceau de scurit est en place, le passage doit tre dgag en permanence. Si le faisceau est mal plac, la scurit ne peut pas tre assure correctement. Assurez-vous que la hauteur du faisceau assure une protection maximale. WARNING: Connect the Safety Beam as per diagram in Fig 6.3.2. Tampering with the Safety Beam could result in serious personal injury and/or property damage and will void the warranty. AVERTISSEMENT : Raccordez le faisceau de scurit conformment au schma Fig.6.3.2. Saboter le faisceau de scurit prsente un risque de blessure corporelle grave et/ou de dommages matriels, et annule la garantie. 6 3 5 7 8 Fig.6.3.1 2 1 3 4 TRANSMITTER RECEIVER Fig.6.3.2 White G

W G

W White Fig 6.3.3 13 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.4 Setting Speed and Limits CAUTION! Limit setup is not available when running on battery backup tip Refer to Appendix G for setting limits via a Premium Remote Control. Fig.6.4.1

(i) Press and hold the CLOSE button to start closing the door, taking note of the speed the door moves. 6.4.1 Set the Limit Positions and adjust drive speed:

The Limit Positions can vary due to site conditions, such as uneven ground. When setting the Close limit, ensure the position is when the door makes first contact with the ground. Alternatively for the Open limit the position should be at the height of the garage opening. NOTE: The drive speed is set to the fastest setting by default. This may not be suitable for larger doors or for single piece doors. For tilt doors

(J-Type only), please refer to Appendix E for initial setup. a. Switch power on and the BLUE LED on the CLOSE button will start to flash and the GEAR opener is ready to set the Close travel limit (Fig 6.4.1). LED is lit to indicate that the b. Press either the CLOSE or OPEN button to move the door to the halfway point. CLOSE limit:

taking note of the speed the door moves.

(ii) If the close speed is not suitable, to make a change, press and hold the CLOSE button and by pressing the STOP / SET button on the opener it will cycle through all three speed modes as shown in table.

(iii) Once at the desired speed, release the CLOSE button.

(iv) To set the close limit, inch the door by making single presses of the CLOSE button the CLOSE limit position being the first point of contact of the rubber strip ( at the bottom of the door) with the ground. to the desired position. We recommend WARNING! In setting the close limit position, do not force the door into the floor with excessive force, as this can interfere with the ease of operation of the manual release mechanism. AVERTISSEMENT: Ne pas forcer la porte contre le sol lors du rglage de fin de course, car une force excessive peut entraver le fonctionnement du systme de dclenchement manuel.

(v) If the door overshoots, press the OPEN button to move the door in the OPEN direction.

(vi) When the door is at the desired CLOSE position, press the STOP

/ SET button on the opener, the GREEN LED on the OPEN button will now flash. NOTE: If unhappy with the speed or travel limit setting, restart this procedure by resetting the door limit positions as per below first. Door Opener Speed Mode Fast (Default) Medium Slow STATUS MAIN LIGHT On On On 3 Flash 2 Flashes 1 Flashes OPEN limit:

(i) Press and hold the OPEN button to start opening the door,

(ii) If the open speed is not suitable, to make a change, press and hold the OPEN button and by pressing the STOP / SET button on the opener it will cycle through all three speed modes as shown in table.

(iii) Once at the desired speed, release the OPEN button.

(iv) Continue inching the door to the desired position.

(v) To set the open limit, inch the door by making single presses of to the desired position. We recommend the OPEN button the OPEN limit position being the height of the garage opening.

(vi) If the door overshoots, press the CLOSE button to move the door in the CLOSE direction. WARNING! The door will automatically close, open and close again after the next step. Ensure that nothing is in the doors path. AVERTISSEMENT : La porte va se fermer puis souvrir automatiquement, avant de se fermer. Sassurer que rien ne bloque louverture ou la fermeture de la porte.

(vii) When the door is at the desired OPEN position, press the STOP

/ SET button. The door will now automatically close and open to calculate the safety obstruction settings. tip Refer to Appendix B & C for adjustments to margins. 6.4.2 Clearing the Door Limit Positions Limit positions can be deleted by:

a. Press the MODE button repetitively until the GEAR b. Press and hold the MODE button for 10 secs, let the MODE button LED is lit. go when the main light stops flashing. c. The close LED will flash continuously to indicate limits have been cleared. 6.4.3 Re-profiling the Door Re-profiling is a simplified way of re-learning the travel characteristic of a previously setup Limit Switch travel installation. Re-profiling can be used when the travel characteristics of the door change due to mechanical adjustments etc. To initiate a re-profile:

a. Limits must be set. b. Press the MODE button repetitively until the GEAR LED is lit. NOTE: If no action is taken within 30 seconds, the opener will return to normal operating mode and restore the original settings. 14 c. Press and hold the CLOSE button for two seconds, the door will open and close by itself to record profile. d. Follow from CLOSE limit: above to set new limit positions. ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6.5 Safety Testing 6.5.1 Obstruction Detection Test Check the Safety Beam photoelectric sensor is operating after the installation. a. Place an obstruction (white vertical surface 6 in. high by 12 in. wide) in the center of the opening, perpendicular to the plane of the door when in the closed position as per Fig 6.5.1. b. Press the CLOSE button or the Premium Remote Control button to close the door. The photoelectric sensor shall sense an obstruction as described above. The door will not move more than an inch (2.54cm), and the opener lights will flash. 6.5.2 Test the Close Cycle and Safety Reversal a. Press the OPEN button or Premium Remote Control button to open the door (If the door starts closing, press the Premium Remote Control button to stop the door, then press Premium Remote Control button again to open). b. Place an object approximately 1-1/2 to 1 (25mm) high (or a 2x 4 board laid flat, with 2 facing the door) on the floor directly under the door, Fig 6.5.2. c. Press the Premium Remote Control button to close door. d. The door should strike the object and re-open wihthin 2 seconds. e. Remove the timber. IMPORTANT WARNING! If the door is closing and is unable to re-open when obstructed, discontinue use. DO NOT use a door with faulty obstruction sensing. Repair fault and re-test before using. AVERTISSEMENT: Si la porte est en train de se refermer et ne peut pas tre rouverte, arrtez de lutiliser. Nutilisez pas une porte dont les dtecteurs dobstacles sont dfectueux. Rparez-les et refaites un essai. 6.5.3 Testing the Open Cycle a. Press the CLOSE button or Premium Remote Control button to close the door. b. Press the Premium Remote Control button again to open the door. c. When the door reaches approximately half way, firmly grab the doors bottom rail - the door should stop. If the door does not reverse readily when closing, or stop when opening, put the door into manual by pulling down on the manual release string to disengage the motor and contact your dealer for support. 6.5.4 Test the Manual Door Operation Periodically disengage the opener and manually operate the door. The door must be smooth to operate by hand. The force required on the bottom rail should not exceed 44lbs (20kg). CAUTION: Take care when testing the safety obstruction force. Excessive force may cause serious personal injury and/or property damage can result from failure to follow this warning. ATTENTION: Testez la rsistance aux obstacles avec prcaution. Une force excessive prsente un risque de blessure corporelle grave et/ou dendommager le matriel si vous ne respectez pas cet avertissement. Fig.6.5.2 2x 4 board Fig.6.5.1 15 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.6 Coding Premium Remote Controls BUTTON REMOTE CONTROL FUNCTION Open / Stop / Close HOLD PET (Pedestrian) Mode Open Light Vacation Mode Fig.6.6.1 HOLD HOLD HOLD HOLD HOLD HOLD tip Refer to Appendix F to set the PET position before coding PET Mode. Button 1 Button 2 Button 4 Fig.6.6.2 Button 3 6.6.1 Setting Remote Control Functions The opener can only operated from 4-button Premium Remote Control that have been programmed into its memory. Up to 64 codes can be stored in the memory. a. Press the MODE button repetitively until the TRANSMIT LED is lit. b. Press and HOLD the button/s indicated in the Fig 6.6.1 to set the required remote control function. The Main light will start to flash rapidly. c. Press one of the four (4) buttons on the Premium Remote Control 3A (Fig 6.6.2) until the main light starts to flash rapidly, then release Premium Remote Control button. d. Press the Premium Remote Control button again until the main light stops flashing rapidly. e. Release both buttons. The Premium Remote Control button is now coded, press to test. NOTE: Refer to the Light indicator table for the details of the Premium Remote Control status. MAIN LIGHT REMOTE CONTROL STATUS ON OFF Button added Button removed 2 FLASHES, then OFF Remote control deleted 4 FLASHES, then OFF Memory full WARNING! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. AVERTISSEMENT! Le fabricant nest pas responsable des ventuelles interfrences avec la rception de la radio ou de la TV due une modification de cet quipement effectue sans autorisation. De telles modifications peuvent invalider le droit utiliser lquipement. 16 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6.6 Coding Premium Remote Controls TRANSMITTERS COMPLIANCE STATEMENT TRANSMITTERS COMPLY WITH ALL UNITED STATES AND CANADIAN LEGAL REQUIREMENTS AS OF THE DATE OF MANUFACTURE. TO COMPLY WITH FCC PART 15 AND OR RSS 210 INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADA RULES, ADJUSTMENT OR MODIFICATIONS OF THIS RECEIVER AND / OR TRANSMITTER ARE PROHIBITED, EXCEPT FOR CHANGING THE CODE SETTING OR REPLACING THE BATTERY. THERE ARE NO OTHER USER SERVICEABLE PARTS. TESTED TO COMPLY WITH FCC STANDARD FOR HOME OR OFFICE USE. THIS DEVICE CONTAINS LICENCE-EXEMPT TRANSMITTER(S)/RECEIVER(S) THAT COMPLY WITH INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADAS LICENCE-EXEMPT RSS(S). OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION OF THE DEVICE. NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER IS ENCOURAGE TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES:

REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE RECEIVER IS CONNECTED. CONSULT YOUR LOCAL DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP. DCLARATION DE CONFORMIT DE L'METTEUR LES METTEURS SONT CONFORMES TOUTES LES EXIGENCES LGALES DES TATS-UNIS ET DU CANADA LA DATE DE FABRICATION. POUR SE CONFORMER AUX RGLES DINNOVATION, SCIENCE ET DVELOPPEMENT CONOMIQUE CANADA PARTIE 15 ET OU RSS 210 DE FAC. LES RGLAGES OU MODIFICATIONS DE CE RCEPTEUR ET/OU METTEUR SONT INTERDITS, L'EXCEPTION DU CHANGEMENT DE CODE OU DU REMPLACEMENT DE LA BATTERIE. AUCUNE AUTRE PICE NE PEUT TRE RPARE PAR L'UTILISATEUR. LMETTEUR/RCEPTEUR EXEMPT DE LICENCE CONTENU DANS LE PRSENT APPAREIL EST CONFORME AUX CNR DINNOCATION, SCIENCES ET DVELOPPEMENT CONOMIQUE CANADA APPLICABLES AUX APPAREILS RADIO EXEMPTS DE LICENCE. LEXPLOITATION EST AUTORISE AUX DEUX CONDITIONS SUIVANTES:

(1) CET APPAREIL NE DOIT PAS CAUSER D'INTERFRENCES;

(2) CET APPAREIL DOIT ACCEPTER TOUTE INTERFRENCE EXTRIEURE, Y COMPRIS CELLES QUI SONT SUSCEPTIBLES DE PROVOQUER UN DYSFONCTIONNEMENT. REMARQUE: CET QUIPEMENT A T TEST ET DCLAR CONFORME AUX LIMITATIONS APPLICABLES UN APPAREIL NUMRIQUE DE CLASSE B, CONFORMMENT AUX DISPOSITIONS DE LA PARTIE 15 DES RGLES DE LA FCC. CES LIMITATIONS VISENT ASSURER UNE PROTECTION SUFFISANTE CONTRE LES INTERFRENCES DANS UNE INSTALLATION RSIDENTIELLE. CET QUIPEMENT DGAGE, UTILISE ET PEUT DIFFUSER DES ONDES RADIO. S'IL N'EST PAS INSTALL ET UTILIS CONFORMMENT AUX INSTRUCTIONS, LES INTERFRENCES PEUVENT PERTURBER LES COMMUNICATIONS RADIO. IL N'Y A TOUTEFOIS AUCUNE GARANTIE QUE DES INTERFRENCES NE SE PRODUIRONT PAS DANS UNE INSTALLATION DONNE. SI CET QUIPEMENT VIENT CAUSER DES INTERFRENCES AVEC LA RCEPTION DE LA RADIO OU DE LA TLVISION, CE QUI PEUT TRE DTERMIN EN L'TEIGNANT ET EN LE RALLUMANT, L'UTILISATEUR EST INVIT Y REMDIER EN PRENANT UNE OU PLUSIEURS DES MESURES SUIVANTES:

RORIENTER OU DPLACER L'ANTENNE DE RCEPTION;

LOIGNER L'QUIPEMENT DU RCEPTEUR;

BRANCHER L'QUIPEMENT DANS UNE PRISE DE COURANT D'UN CIRCUIT LECTRIQUE DIFFRENT. LE CAS CHANT, CONSULTEZ VOTRE REVENDEUR OU UN TECHNICIEN RADIO/TV EXPRIMENT. 17 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.6 Coding Premium Remote Controls 6.6.2 Erasing All Premium Remote Control Codes a. Press the MODE button repetitively until the TRANSMIT LED is lit. b. Press and hold the MODE button for 10 secs, let the MODE button go when the main light stops flashing. c. Follow steps a - e in 6.6.1 Setting the Premium Remote Control Code to code new remote controls. 6.6.3 Vacation Mode a. To turn on Vacation mode and lock out all remote controls, press the button on the remote programmed with Vacation Mode. b. To turn off Vacation Mode, press the Premium Remote Control button programmed to vacation mode to turn off. 6.6.4 Remotely Coding Premium Remote Controls Using this method remote controls can be coded without access to the openers control panel as long as a pre-coded remote control is available. a. Take any pre-coded Premium Remote Control. Press the button for the function to be duplicated and release. b. Using a small pen, press and hold firmly for two seconds the middle button, through the Coding Hole (Fig 6.6.2). c. Within ten (10) seconds take the additional remote control you wish to code. Hold the new remote controls button for two seconds, pause for two seconds, hold again for two seconds and then release. d. Wait for ten (10) seconds and then press the new remote controls button to test. 6.6.5 Install Premium Wall Control a. Turn the Premium Wall Control over and pull the tab to commission the battery.

(Fig 6.6.3) b. Store the Remote Control Function as per instructions in Section 6.6.1. Test the Premium Wall Control button. c. Mount the Premium Wall Control using parts provided in a convenient location, yet out of reach of children and at least 5 feet off the ground.

(Fig 6.6.4) d. Make sure the door is visible from this location. Fig.6.6.2 Fig.6.6.3 Fig.6.6.4 IMPORTANT WARNING LOCATE THE WALL MOUNTED REMOTE CONTROL:

IMPORTANT PLACEZ LA TLCOMMANDE MURALE:

(1) WITHIN SIGHT OF DOOR.

(2) AT MINIMUM HEIGHT OF 5 FEET ABOVE FLOORS, LANDINGS, STEPS OR OTHER ADJACENT WALKING SURFACE SO SHALL CHILDREN ARE NOT ABLE TO REACH IT, AND

(1) EN VUE DE LA PORTE.

(2) UNE HAUTEUR D'AU MOINS 1,50M (5PIEDS) AU-

DESSUS DU SOL, DU PERRON, DES MARCHES, ETC. AFIN QUE LES PETITS ENFANTS NE PUISSENT PAS L'ATTEINDRE,

(3) AWAY FROM MOVING PARTS OF THE DOOR.

(4) PLACE THE ATTACHED ENTRAPMENT WARNING LABEL ON WALL NEXT TO WALL MOUNTED TRANSMITTER. USE AN ADDITIONAL MECHANICAL MEANS (PLATE, BOARD, ETC.), WHICH CAN SECURE THE LABELS TO SURFACES TO WHICH THE ADHESIVE WILL NOT ADHERE.

(3) ET DISTANCE DES LMENTS MOBILES DE LA PORTE.

(4) PLACEZ L'TIQUETTE AVERTISSANT DU RISQUE DE SE FAIRE PIGER SUR LE MUR PROXIMIT DE L'METTEUR. UTILISEZ UN SUPPORT PHYSIQUE SUPPLMENTAIRE (PLAQUE, PANNEAU, ETC.) PERMETTANT DE FIXER LES TIQUETTES SI ELLES N'ADHRENT PAS LA SURFACE DU MUR.

(5) DO NOT REMOVE OR PAINT OVER THIS LABEL.

(5) CETTE TIQUETTE NE DOIT PAS TRE RETIRE NI PEINTE. 18 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6.7 Battery Backup 6.7.1 Connecting the Battery Backup

(Optional with ATS-3AM & ATS-2AM models) a. Remove the screw and open the cover to the batteries. (Fig.6.7.1) WARNING! After Step (c) the opener may become active (even when power is off). This is a result of a residual charge in the batteries. AVERTISSEMENT! Aprs ltape (b) loprateur peut deviendra actif (mme alimentation est teinte). Ceci est un rsultat dune charge rsiduel dans les batteries. b. Connect the coupling blue harness 2A to the red plus terminal A+ on Battery A , then connect coupling blue harness 2B to the black minus terminal B- on Battery B . c. Connect the coupling black wire 4A to the black minus terminal A- on Battery A , then connect coupling red wire 4B to the red plus terminal B+ on Battery B . d. Close the cover, securing with screw and reconnect power. NOTE: Batteries may take up to 24 hours to charge fully after initial installation. Fig.6.7.1 2B B 4B B+

A-

B-

A+

2A A 4A 6.7.2 Test the Opener a. Press either the OPEN or CLOSE button to test the battery backup 6.7.3 LED Battery indicator b. Whilst door is in motion, disconnect mains power. The door should Battery LED Battery Status installation. continue to operate as normal. c. Press either the OPEN or CLOSE button to activate the door. Whilst door is in motion, reconnect power. The door should complete the cycle as normal. OFF ON Not Fitted / Not used Charged In use Charging Blink every 2 sec Flashing Rapid Flashing Battery Fault 6.8 Accessories 6.8.1 Terminal Block Wired accessory items can be connected to the terminal block J4. Terminal connections from top down are as follows (Fig. 6.8.1):

a. +35V (Auxillary) b. AUX (Auxillary) c. SB (Safety Beam input, mandatory);

d. GND (Common ground for accessories and Safety Beam);

e. GND (Common ground) f. OSC (Open/Stop/Close trigger) Refer to Appendix B for how to adjust parameters. 6.8.2 Connecting or Disconnecting Accessories When disconnecting or reconnecting accessory base station modules (Wireless PE Beams) press the MODE button on the opener repetitively until the GEAR LED is on, then press the STOP / SET button until the main courtesy light stops flashing. NOTE: If an Auto-lock is installed ensure that the channels on the transceivers on each device are different. The channel on the transceiver can be changed by sliding the switch in either direction Fig.6.8.1 19 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.9 Auto-Ki Smart Phone Control

(ATS-3AM & ATS-3AMB Only) CAN ICES-3 (B)/NMB-3 (B) CLASS B DEVICE This equiment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help. To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.87in (20cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This network device allows for unattended operation of the door when not in line-of-sight of the door opener. The door may operate unexpectedly, therefore do not allow anything to stay in or near the path of the door. When the door is not operating automatically, watch the door when it is moving and keep people away until the door is completely opened or closed. Contact with the moving door can cause serious personal injury or damage to property. Tout changement ou toute modification non expressment approuve par la partie responsable de la conformit est susceptible dannuler le droit de lutilisateur dutiliser lquipement. La tlcommande radio permet dactionner la porte lorsque lutilisateur est hors de la ligne de vue de la porte et de lappareil. En consquence, la porte risque de souvrir ou se fermer inopinment et vous devez viter de laisser des objets sur sa course ou proximit. Lorsque la porte ne fonctionne pas automatiquement, surveillez-la lorsquelle bouge et loignez toute personne jusqu ce quelle soit compltement ouverte ou ferme. Le contact avec la porte en mouvement peut provoquer des blessures graves ou des dommages matriels. 20 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 6.9 Auto-Ki Smart Phone Control

(ATS-3AM & ATS-3AMB Only) Your opener must be fitted with SAFETY BEAMS. Safety Beams detect any obstructions in the doors path and override automatic operation if one presents. These must be installed as in accordance with UL 325 and CSA C222.2 No 247. This is in addition to regular professional servicing, and monthly obstruction tests as detailed in your openers Owners Manual. The compliance to FCC radiation exposure limits for an uncontrolled environment, and a minimum of 20cm separation between antenna and body. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Votre ouvre-porte doit tre quip de FAISCEAUX DE SCURIT. Les faisceaux de scurit dtectent tout obstacle sur le trajet de la porte et annulent alors le fonctionnement automatique. Ceux-ci doivent tre installs conformment aux normes UL 325 et CSA C222.2 N 247. Ceci sajoute lentretien professionnel rgulier et aux tests dobstruction mensuels dtaills dans le mode demploi de votre ouvre-porte.. Conformit aux limites dexposition aux rayonnements FCC pour un environnement non contrl, et distance minimale de 20 cm entre lantenne et le corps. Ce dispositif est conforme la partie 15 des rgles de la Federal Communications Commission (FCC). Son fonctionnement est assujetti aux deux conditions suivantes: (1) Ce dispositive ne doit pas provoquer de brouillage prjudiciable, et (2) il doit accepter tout brouillage reu, y compris le brouillage pouvant entraner un mauvais fonctionnement. tip Ensure limits are set prior to connecting to Wifi. 6.9.1 Connecting to Wifi The Smart Phone Control works via your homes WiFi network. Initial set up involves linking your phone app, smart hub and opener to your home network. a. Download the ATA App. b. Ensure the WiFi router is within range of the opener. c. On the opener press the MODE button repetitively until the NETWORK LED is lit. (Fig 6.9.1) d. Press and hold the OPEN button on the opener for 4 seconds. The NETWORK LED will turn purple when Hot Spot is Active. e. Go to phone settings, then WiFi and select (ATA000000). f. Open App and tap on Start. g. Select setup a new Smart Hub h. When Smart hub hotspot connection appears, select OK got it. i. Ensure WiFi network = (ATA000000) then select connect to hub. j. The opener main light and a red NETWORK LED will start to flash. k. Press STOP / SET button on the opener. l. Name your smart hub on the app and select SAVE. s. The NETWORK t. Now you can test the app. LED will change to solid blue. m. Set the time zone and SAVE. n. Create an admin user and select OK got it. o. Fill in name and password and select CREATE. p. Fill in email and security question or select skip this step and select SAVE. q. Select the push notification and select SAVE. r. Select and connect to WiFi. Choose your home WiFi and fill in password and select connect. tip ATA App local operation will continue when the internet is down and the home router Wi-Fi is operational. Fig.6.9.1 21 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 6.10 Auto-Close 6.10.1 Auto-Close Auto-Close mode is a function that automatically closes the door after a pre-set time. Safety beams must be installed in order to run the Auto-Close function. There are two types of Auto-Close available:

(i) Standard auto-close - the door will Auto-Close after a programmed time. In this mode the timer starts to countdown as soon as the door is fully open. This function is useful in case the safety beam does not get triggered.

(ii) Safety Beam triggered auto-close - the door will auto-close after a programmed time. In this mode the timer starts counting down only when the safety beam is triggered. ie car leaving the garage. To enable the Auto-Close function:

a. Press the MODE button repetitively until the GEAR LED starts flashing. b. Press the OPEN button until the GEAR LED flashes:

two (2) times to get to PE auto-close or

(i)

(ii) three (3) times to get to standard auto-close. c. Press STOP / SET button to enter parameter. d. The default setting for Auto-Close is OFF. Parameter Press the OPEN button to move through options and the lights brightness will change accordingly. e. Press STOP / SET button to save the parameters new value or press MODE to leave the value unchanged. WARNING! It is compulsory to have Safety Beams installed when using Auto-Close mode. AVERTISSEMENT! Le faisceau de scurit doit tre install lorsque vous utilisez le mode Auto-Close. Value options = Indicated by brightness of main light

(DEFAULT parameter underlined) Name Flashes 2 3 4 5 PE AUTO-CLOSE AUTO-CLOSE x2 x3 15sec 30sec 60sec 90sec 15sec 30sec 60sec 90sec 120sec 1 OFF OFF 6

6.11 Attach Warning Labels 6.11.1 Placement of Warning labels Attach the entrapment warning label on the wall near the door control with tacks or staples at a minimum hright of 5 feet above floors, landings, steps or other adjacent walking surface so shall children are not able to reach it. Place the attached entrapment warning label on wall. Use an additional mechanical means (plate, board etc.) which can secure the labels to surfaces to which the adhesive will not adhere. DO NOT REMOVE OR PAINT OVER THIS LABEL 4 5 2 1 3 2 1 140 6 3 ATTENTION!

CAUTION!

Sassurer que ce label de scurit soit plac dans un emplacement prominent de faon tre vu et lu.. Les consignes de scurit doivent tre expliques aux adultes et aux enfants et DOIVENT tre respectes. Dautres consignes de scurit figurent dans le manuel des instructions d'installation. TEAR LINE Please ensure that this Safety Label is placed in a prominent location so that it can be viewed and read. The warnings should be explained to all children and adults and MUST be followed. Further Safety Information is available in the Owners Copy of the Installation Instruction. TEAR LINE AVERTISSMENT A B C D E F 22 A B C F 0 8 1 0 1 2 WARNING There is risk of a child becoming trapped under an automatic garage door resulting in severe injury or death. 1. 2. 3. 4. 5. 6. 7. 8. 9. Never let children walk or run under a moving door. Never let children operate door operator controls. Always keep moving door in sight. In the event a person is trapped under the door, push the control button or use the emergency release. Keep Garage Door Properly Balanced. Test Door Operator Monthly (refer to your Owners Manual): Use a 1-1/2-inch high object (or a 2 by 4 board laid flat) on the floor under the closing door. In the event the door does not reverse upon contact, adjust, repair, or replace the operator. DO NOT REMOVE OR PAINT OVER THIS LABEL. Mount this label adjacent to the wall control, and mount the wall control out of childrens reach (at least 5 feet above floor). Except for Model AM800, this Operator System is equipped with an unattended operation feature. The door could move unexpectedly. No one should cross the path of the moving door. PROPRIETARY AND CONFIDENTIAL DESCRIPTION GENERAL TOLERANCES:

TITLE:

ANGLE:

DEBUR AND BREAK SHARP EDGES G.KINGSLAND 30/04/18 DATE SCALE:

160566_00 86204 Un enfant peut tre coinc sous une porte de garage automatiue. Ceci peut causer des blessures graves ou mme entraner la mort. D 1. Ne jamais laisser un enfant marcher ou courir sous une porte en mouvement. 2. Ne jamais laisser un enfant actionner loure-porte de garage. 3. Toujours surveiller la porte lorsquelle est en mouvement. 4. Au cas o une personne serait coince sous une porte, appuyer sur le bouton de contrle, ou dclencher le dverrouillage de secours. 5. Maintenir toujours la porte de garage bien quilibre. 6. Verier louver-porte chaque mois (consulter le manuel du propritaire): utiliser un objet de 1-1/2 pouce de hauteur (ou une planche de 2x4 pose plat) sur le sol sous la porte qui se ferme. Si au contact, la porte ne remonte pas, il sera ncessaire de procder un rglage, de rparer, ou de remplacer le mcanisme. 7. NE PAS ENLEVER CETTE TIQUETTE NI LA COUVRIR DE PEINTURE. 8. Placer ce label de signalisation de danger prs du commutateur mural et installer le commutateur mural hors de porte des enfants (au moins 1.5 m (5) du sol). 9. Ce systme de loperateur est quipe avec une E opration feature unattended. La porte pourrait passer inopinment. Personne ne doit traverser la trajectoire dune porte en mouvement. ITEM DWG NO. DESCRIPTION QTY MATERIAL PART#

1 ADHESIVE LABEL PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF AUTOMATIC TECHNOLOGY AUSTRALIA Pty Ltd. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF AUTOMATIC TECHNOLOGY AUSTRALIA Pty Ltd. IS PROHIBITED. GENERAL TOLERANCES:

DECIMAL: 0.X 0.1 0.XX 0.05 ANGLE: 0.5 RADIUS: 0.5 CHAMFER: 0.5 x 45 SURFACE FINISH DEBUR AND BREAK SHARP EDGES NAME DATE TOAN DANG 05.07.12 TITLE:

Automatic Technology Australia Pty Ltd. 6-8 FIVEWAYS BOULEVARD, KEYSBOROUGH, VIC, 3173, AUSTRALIA PHONE: +61(0) 3 9791 0200 FAX: +61(0) 3 9791 0250 WEB: www.ata-aust.com.au ENTRAPMENT WARNING LABEL_CAN-US_ENGLISH DRAWING NO. 15020190 SCALE:

1 : 1 PART NO. 44501 REV. B SHEET A3 7 4 8 5 6 7 8 Fig.6.11.1 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual WARNING! Ensure to have hand brake on whilst setting homelink button and do not allow anything to stay in or near the path of the door. Keep people away until the door is completely opened or closed. AVERTISSEMENT : Assurez-vous que le frein main est activ lors du rglage du bouton homelink et ne laissez rien rester dans ou prs du chemin de la porte. loignez les personnes jusqu ce que la porte soit compltement ouverte ou ferme. 6.12 Homelink tip Some vehicles may require the ignition be turned on to program the HomeLink Button. tip Park the vehicle outside of the garage where the opening is clearly visible and leave window down to hear sounds. 6.12.1 Coding in the HomeLink button a. Press and hold the two outside buttons on the HomeLink system until the LED starts to blink, release buttons. b. Hold the ATA single button remote control 3B in hand and position it 1-3 inches (3-8cm) from the HomeLink button as in 6.12.1. c. Press and hold the desired HomeLink button and ATA single button 3B at the same time until the HomeLink LED changes from a slow blink to a rapid blink. d. Release both buttons. The HomeLink button is ready to be coded into the ATS-Series garage door operator. 6.12.2 Coding HomeLink button into the ATS-Series Operator a. Press the MODE button repetitively until the TRANSMIT LED is flashing slowly. b. Press and release the CLOSE button

- operator will start to flash and beep slowly for 20secs to allow the user to go to the car. c. After 20 seconds the operator will start to beep and flash quickly. Press and hold the HomeLink button to be code set for 2 secs. d. Release the HomeLink button for 5 seconds, then press and hold the same HomeLink button again for 2 secs - the flashing and beeping will stop. e. Test the operation of the HomeLink button. 6.12.3 Erasing all HomeLink buttons from the ATS-Series Operator a. Press the MODE button repetitively until the TRANSMIT LED is flashing slowly. b. Press and hold MODE button. c. The operator will start to flash and beep after 5 seconds. When the flashing and beeping stops, release the MODE button. tip Keep the ATA Single Button Remote Control 3B in a safe place for future use. This will be needed if and when you change cars. Fig.6.12.1 23 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 7. Operation Instructions IMPORTANT SAFETY INSTRUCTIONS WARNING! TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:

(1) READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

(2) NEVER LET CHILDREN OPERATE OR PLAY WITH DOOR CONTROLS. KEEP THE REMOTE CONTROL AWAY FROM CHILDREN.

(3) ALWAYS KEEP THE MOVING DOOR IN SIGHT AND AWAY FROM PEOPLE AND OBJECTS UNTIL IT IS COMPLETELY CLOSED. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

(4) NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

(5) TEST DOOR OPENER MONTHLY. THE GARAGE DOOR MUST REVERSE ON CONTACT WITH A 1-1/2-INCH HIGH OBJECT (OR A 2 BY 4 BOARD LAID FLAT) ON THE FLOOR. AFTER ADJUSTING EITHER THE FORCE OR THE LIMIT OF TRAVEL, RETEST THE DOOR OPENER. FAILURE TO ADJUST THE OPENER PROPERLY INCREASES THE RISK OF SEVERE INJURY OR DEATH.

(6) FOR PRODUCTS HAVING AN EMERGENCY RELEASE, WHEN POSSIBLE, USE THE EMERGENCY RELEASE ONLY WHEN THE DOOR IS CLOSED. USE CAUTION WHEN USING THIS RELEASE WITH THE DOOR OPEN. WEAK OR BROKEN SPRINGS ARE CAPABLE OF INCREASING THE RATE OF DOOR CLOSURE AND INCREASING THE RISK OF SEVERE INJURY OR DEATH.

(7) KEEP GARAGE DOORS PROPERLY BALANCED. SEE OWNERS MANUAL. AN IMPROPERLY BALANCED DOOR INCREASES THE RISK OF SEVERE INJURY OR DEATH. HAVE A QUALIFIED SERVICE PERSON MAKE REPAIRS TO CABLES, SPRING ASSEMBLIES, AND OTHER HARDWARE.

(8) EXCEPT FOR MODEL ATS-2 & ATS-2AMB, THIS OPERATOR SYSTEM IS EQUIPPED WITH AN UNATTENDED OPERATION FEATURE. THE DOOR COULD MOVE UNEXPECTEDLY. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

(9) THIS PRODUCT CONTAINS A LITHIUM BUTTON/COIN CELL BATTERY. IF A NEW OR USED LITHIUM BUTTON/COIN CELL BATTERY IS SWALLOWED OR ENTERS THE BODY, IT CAN CAUSE SEVERE INTERNAL BURNS AND CAN LEAD TO DEATH IN AS LITTLE AS 2 HOURS. ALWAYS COMPLETELY SECURE THE BATTERY COMPARTMENT. IF THE BATTERY COMPARTMENT DOES NOT CLOSE SECURELY, STOP USING THE PRODUCT, REMOVE THE BATTERIES, AND KEEP IT AWAY FROM CHILDREN. IF YOU THINK BATTERIES MIGHT HAVE BEEN SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY, SEEK IMMEDIATE MEDICAL ATTENTION.

(10) SAVE THESE INSTRUCTIONS. AVERTISSEMENT!

POUR RDUIRE LE RISQUE DE BLESSURES GRAVES, VOIRE DE MORT:

(1) LISEZ ATTENTIVEMENT TOUTES LES INSTRUCTIONS DINSTALLATION.

(2) NE LAISSEZ JAMAIS LES ENFANTS UTILISER LES COMMANDES DE LA PORTE OU JOUER AVEC. LA TLCOMMANDE DOIT RESTER HORS DE PORTE DES ENFANTS.

(3) GARDEZ TOUJOURS LA PORTE EN MOUVEMENT DANS VOTRE LIGNE DE VISION, ET VEILLEZ CE QUELLE RESTE ENTIREMENT DGAGE JUSQU SA FERMETURE COMPLTE. PERSONNE NE DOIT SE TENIR DANS LE PASSAGE PENDANT QUE LA PORTE EST EN MOUVEMENT.

(4) NE STATIONNEZ JAMAIS SOUS UNE PORTE PARTIELLEMENT OUVERTE.

(5) TESTEZ LE DISPOSITIF DOUVERTURE UNE FOIS PAR MOIS. LA PORTE DOIT OBLIGATOIREMENT INVERSER SA COURSE EN CAS DE CONTACT AVEC UN OBJET DE 25 40MM (1-1/2) (OU UNE PLANCHE DE 5X10 CM [2X4]POSE PLAT) AU MILIEU DU PASSAGE. APRS AVOIR RGL LA FORCE OU LA LIMITE DE COURSE, REFAITES UN ESSAI DU SYSTME DOUVERTURE DE PORTE. LE DISPOSITIF DOUVERTURE DOIT TRE BIEN RGL AFIN DE RDUIRE LE RISQUE DE BLESSURES GRAVES, VOIRE DE MORT.

(6) DANS LE CAS DES PRODUITS QUIPS DUN DBLOCAGE DURGENCE, UTILISEZ-LE DANS LA MESURE DU POSSIBLE UNIQUEMENT QUAND LA PORTE EST FERME. SOYEZ PRUDENT SI VOUS ACTIONNEZ CE DISPOSITIF DE DBLOCAGE ALORS QUE LA PORTE EST OUVERTE. DES RESSORTS FAIBLES OU CASSS RISQUENT DACCLRER LA FERMETURE DE LA PORTE ET DE CAUSER DES BLESSURES GRAVES, VOIRE DE PRSENTER UN DANGER DE MORT.

(7) LES PORTES DE GARAGE DOIVENT TOUJOURS TRE CORRECTEMENT QUILIBRES. REPORTEZ-VOUS AU MANUEL. UNE PORTE MAL QUILIBRE PRSENTE UN DANGER DE BLESSURES GRAVES, VOIRE DE MORT. LES RPARATIONS DES CBLES, DES ASSEMBLAGES RESSORT ET AUTRES LMENTS MATRIELS DOIVENT TRE EFFECTUES PAR UN TECHNICIEN QUALIFI.

(8) HORMIS DANS LE CAS DU MODLE ATS-2 ET ATS-2AMB CE SYSTME EST QUIP DUNE FONCTION DUTILISATION SANS SURVEILLANCE. LA PORTE POUVANT SOUVRIR OU SE FERMER INOPINMENT, PERSONNE NE DOIT SE TROUVER DANS LE PASSAGE PENDANT QUELLE EST EN MOUVEMENT.

(9) CE PRODUIT CONTIENT UNE PILE BOUTON/MONNAIE AU LITHIUM. SI UNE PILE BOUTON/MONNAIE AU LITHIUM NEUVE OU USAGE EST AVALE OU PNTRE DANS LE CORPS, ELLE PEUT CAUSER DE GRAVES BRLURES INTERNES ET PEUT ENTRANER LA MORT EN DEUX HEURES SEULEMENT. TOUJOURS SCURISER COMPLTEMENT LE COMPARTIMENT DES PILES. SI LE COMPARTIMENT DES PILES NE SE FERME PAS CORRECTEMENT, ARRTEZ DUTILISER LE PRODUIT, RETIREZ LES PILES ET GARDEZ-LE HORS DE PORTE DES ENFANTS. SI VOUS PENSEZ QUE DES PILES ONT PU TRE AVALES OU PLACES DANS UNE PARTIE QUELCONQUE DU CORPS, CONSULTEZ IMMDIATEMENT UN MDECIN. 24

(10) CONSERVEZ CES INSTRUCTIONS EN LIEU SR. ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual POUR RDUIRE LE RISQUE DE BLESSURES GRAVES, VOIRE DE MORT:

AVERTISSEMENT!

7.1 How to Use Your Operator For maximum efficiency of your operator, your garage door must be in good operating condition. An annual service of your garage door by door professional is recommended. WARNING! This operator has a grounding type plug and there are no user serviceable parts inside this operator. AVERTISSEMENT! Ce dispositif de commande est pourvu dune broche de mise la terre et ne comporte aucune pice rparable par lutilisateur. CAUTION: Activate the operator only when the door is in full view, free of obstructions and with the operator properly adjusted. No one should enter or leave the garage while the door is in motion. Do not allow children to play near the door. ATTENTION: Activez le dispositif de commande uniquement lorsque la porte est en pleine vue, dgage et avec le dispositif correctement rgl. Personne ne doit entrer ou sortir du garage pendant que la porte est en mouvement. Ne pas laisser les enfants jouer prs de la porte. 7.1.1 To Operate the opener:

a. Press the programmed transmitter button or HomeLink until your door begins to move (usually 2 seconds). Make sure you can see the door when you use the transmitter (Fig 7.1.1). b. If you are in a vehicle you should aim the transmitter through your windscreen as shown. c. Check that the door is fully open or closed before you drive in or away. d. If you press the transmitter whilst the door is moving the door will stop. The next press of the transmitter will move the door in the opposite direction. 7.1.2 Replacing the Battery: 3V Lithium Battery CR2032. To test the battery is working, press and hold a transmitter button. Check Light Status table to determine if battery needs replacing. Light Status Battery Status Solid Flashing No light OK Requires replacement Requires replacement Premium Remote Control a. Remove screw from back of cover. b. Use screw driver to separate the remote control casing to expose circuit c. Use a non-metallic object (e.g. pen) to remove the battery. board.

(Fig. 7.1.2). Premium Wall Button a. Follow instructions in Fig 7.1.3 to replace battery. REPLACE WITH BATTERY CR2032 S T E P O N E S T E P T W O WARNING! Chemical Burn Hazard. Keep batteries away from children AVERTISSEMENT! Risque de brlure chimique:

Gardez les piles hors de porte des enfants. O R WARNING! The Battery shall be disposed of properly, including keeping them away from children. Even used batteries may cause injury. AVERTISSEMENT! La batterie doit tre mise au rebut de manire approprie, notamment en la gardant hors de porte des enfants. Mme les piles uses peuvent provoquer des blessures. l i f t l i d , s l i d e u p &

o f f s c r e w s p e e l o f f f r o m v e l c r o U s e p e n t o l i f t l i d , t h e n p u s h a n d r e l e a s e b a t t e r y R e p l a c e b a t t e r y a n d r e m o u n t t o w a l l . D i s p o s e o f b a t t e r y r e s p o n s i b l y Fig.7.1.1 Fig.7.1.2 Fig.7.1.3 25 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 7.2 User Operating Controls Button Function 1. DOWN ARROW (Blue) Closes the door 3. STOP (Red) Stops the door 4. UP ARROW (Green) Opens the door 2. DOWN ARROW LED (Blue) Illuminates when the door is closed and flashes when the door is closing, obstructed on close or stopped. 5. UP ARROW LED (Green) Illuminates when the door is open and flashes when the door is opening, open with the auto-close timer running, obstructed on opening or stopped. 6. MODE (Yellow) Enables Load Diagnostics Mode 7. MODE STATUS LED (Yellow) Illuminates when in Diagnostics Mode 8. BATTERY STATUS LED (Yellow) Illuminates when battery is charged and flashes when battery is charging, in use or battery failed. 9. REMOTE CONTROL STATUS LED (Red) Flashes on remote lockout and flickers on remote control activity 10. ADJUSTMENT LED (Yellow) Flashes a certain number of times depending on the parameter being changed. 11. NETWORK LED

(ATS-3 & ATS-3AMB Only) Is a dual colour LED. Illuminates purple when hot spot active, blue when connected to cloud and red when in production mode. Flashes different colour depending on the activity. 01 02 03 04 05 06 07 11 10 09 08 26 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 7.3. Troubleshooting Symptom Possible cause Remedy The opener does not work from the Premium Remote Control Garage door in poor condition e.g. springs may be broken Check the doors operation The opener does not have power Plug a device of similar voltage (e.g. a hairdryer) into the power point and check that it is OK The battery in the Premium Remote Control is flat The opener has turned on Vacation Mode The Premium Remote Control button is not programmed to operate the door. Replace the battery Turn off Vacation Mode

(Section 6.6.4) Code in the Premium Remote Control One Premium Remote Control works but the other/s do not Faulty Premium Remote Control Flat battery Replace Premium Remote Control Replace battery The opener is disengaged Re-engage the opener Damage motor assembly Contact your dealer for support. The chain / belt moves but the door remains stationary Motor is running but chain /

belt is not moving The Premium Remote Control range varies or is restricted Variations are normal depending on conditions e.g. temperature or external interference Make sure you can see the door when you use the Premium Remote Control. The Courtesy light does not work LED has failed The door reverses for no apparent reason The battery life is exhausted Position of the Premium Remote Control in the motor vehicle Check the battery status by pressing a button (flashing or no light, battery need changing) Aim the Premium Remote Control through the windscreen. Change LED. This may occur occasionally from environmental conditions such as areas that are windy, dusty or have extreme temperature changes. If Safety beams are installed they may be partially obstructed. Ensure the door runs smoothly before increasing the force pressure. Ensure the beam path is not obstructed. Check the Alignment. Door will not close Safety Beam not working Auto Close not working Safety Beam or wiring faulty Safety Beam battery flat The batteries may have little or no charge The door stops or moves very slowly under battery

(Optional Battery Back Up Accessory) The CLOSE (Blue) LED is flashing To access safety close mode, hold the Premium Remote Control button to close for 6 seconds and continue to hold while the door closes. Check Safety Beam Repair Safety Beam or replace wiring. Re-align optics. See Safety Beam instructions. Connect mains power and leave the batteries to charge. The batteries may take 24 hours to reach their maximum charge capacity. Limits are not set Set Up Limits (Section 6.4). 27 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 7.4. Service / Warning Indicator 7.4.1 Main Light = Service / Warning Indicator:

Requirements for a service and user warnings are indicated after operation by the main light repeatably flashing OFF a number of times followed by a pause. When the alert is first triggered the beeper will also sound. The below table identifys the issues and remedies. Flashes Issue Remedy x 1 Normal operation (door is fully open) x 2 PE is preventing door from moving x 3 NOT AVAILABLE x 5 NOT AVAILABLE x 4 Wireless PE battery is low Change PE Battery Clear away any obstructions. Test Door. If unable to move the door and suspect beam is faulty, enter Safety Beam Emergency Close by pressing and holding a pre-coded button on the remote control for more than five seconds and the door will start closing. x 6 Maintenance is due after pre-set number of cycles. Contact dealer to arrange service. x 7 Backup battery is faulty Contact (800) 934 9892 within America for assistance x 8 Door has hit an obstruction x 9 Motor has overloaded or stalled x 10 Battery backup activated - mains power is off Clear away any obstructions and test door opens/closes correctly. (If door is damaged, contact your door professional) Check the doors operation by disengaging the motor and ensuring the door runs smoothly. If necessary make door adjustments or contact your door professional. Main light will flash (3) three times at the start of the cycle to indicate opener is running from battery backup and 10 flashes at the end of cycle. Check power supply. 7.4.2 Main Light = FAULT Status Indicator (when MODE is on):

When MODE is ON, light flashes indicated number of times. When first triggered, the beeper will sound the indicated number of beeps. Attempting to operate the door will result in the beeps being heard again. The below table identifys the issues and remedies. Failed while profiling door after setting limits. Can be caused by any event which cause door to stop. For example P.E beam being blocked on closing, hit an obstruction, etc. Also can occur if battery is activated. Flashes FAULT x 2 or x 3 x 4 or x 5 Position Fault x 6 Motor driving in wrong direction x 7 Memory fault x 8 Motor current sensor fault. 7.4.3 Connecting or Disconnecting Accessories:

When disconnecting or reconnecting accessory base station modules (Wireless PE Beams or Autolock) press the MODE button repetitively until the GEAR LED is on, the press the STOP / SET button until the main courtesy light stops flashing. 28 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 7.5 Disposal of Batteries 7.5.1 Correct Disposal of Batteries:

Button Batteries contain toxic materials and should never be disposed of in the trash WARNING! Button cell lithium batteries MUST have their battery terminals covered BEFORE placing them in the box for shipping. The best way to do this is by taking a strip of tape to make a battery ribbon. AVERTISSEMENT! Les piles bouton au lithium DOIVENT avoir leurs bornes couvertes AVANT de les placer dans la bote pour lexpdition. La meilleure faon de procder est de prendre une bande de ruban adhsif pour crer un ruban de batterie. Recycling all batteries will have other environmental and social benefits:

Some batteries are less toxic but hazardous for other reasons. Lithium batteries can explode or catch fire in landfill, while button cells are dangerous if swallowed by children. Recycling offers a safe and environmentally responsible solution for end of life batteries. Battery recycling recovers non-renewable materials such as lead, cadmium, stella, zinc, manganese, cobalt, silver, plastics and rare earth elements. Removal of batteries and other hazardous household products from household waste facilitates the recovery of organic materials through alternative waste technologies such as composting. Batteries and heavy metals are known contaminants in compost. landfill and achieves environmental benefits. The community supports recycling because it reduces waste to WARNING! The Battery shall be disposed of properly, including keeping them away from children. Even used batteries may cause injury. AVERTISSEMENT! La batterie doit tre mise au rebut de manire approprie, notamment en la gardant hors de porte des enfants. Mme les piles uses peuvent provoquer des blessures. In the United States of America;

Call your local solid waste district to find out if your community has a collection program or upcoming event. Or call 1-800-CLEAN-UP (253-2687) or enter a ZIP code at this website to find the nearest recycling center. Information about most recyclable household waste, including household hazardous waste collection centers, is included. Search the area for recycling centers that accept single-use batteries using Earth911.com Recycling Search. Or call 1-800-CLEAN-UP (1-800-

253-2687), a service of Earth 911, to find the nearest recycling center. The website includes information about most recyclable household waste, including household hazardous waste collection centers. CalRecycle E-Waste Disposal Search Directory. Find an E-waste collector or recycler near you to recycle electronic devices that contain embedded batteries. agencies. embedded batteries. agencies. Find Local Governmental Household Hazardous Waste Agencies. See the website for local governmental household hazardous waste In Canada;

Find a list of locations on the Call2Recycle.ca battery recycling website. Cal2Recycle E-Waste Disposal Search Directory. Find an E-waste collector or recycler near you to recycle electronic devices that contain Find Local Governmental Household Hazardous Waste Agencies. See the website for local governmental household hazardous waste 29 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 8. User Maintenance Instruction CAUTION: Frequently examine the in particular cables, springs and mountings, for signs of wear, damage or imbalance. DO NOT USE if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. installation, Adjustments should only be carried out by experienced persons, as this function can be dangerous if not performed under strict safety procedures. ATTENTION: Examinez frquemment linstallation, en particulier les cbles, les ressorts et les supports, afin de dceler les ventuels signes dusure, de dommage ou de dsquilibre. NE PAS utiliser si la rparation ou un rglage est ncessaire, car un dfaut dans linstallation ou une porte mal quilibre peut causer des blessures. Les rglages ajustements ne doivent tre effectus que par des techniciens expriments, car cette fonction peut tre dangereuse si elle nest pas effectue dans le strict respect des procdures de scurit. WARNING! Failure to maintain your garage door may void the warranty on your garage door operator. AVERTISSEMENT! Labsence dentretien votre porte de garage peut annuler la garantie de votre dispositif douverture. WARNING! Run the Safety Testing procedures MONTHLY in Section 6.5 to ensure garage door is fit for use. AVERTISSEMENT! Appliquez les procdures de test de la section 6.5 UNE FOIS PAR MOIS pour vous assurer que la porte est en tat de marche. 8.1 Door Maintenance A poorly maintained door could cause fatal / serious injuries or damage to property. a. Frequently examine the door, particularly the cables, springs and mountings for signs of wear, damage or imbalance. DO NOT USE if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. b. Fasteners: Check all screws, nuts and bolts to ensure they are secure. c. Spring Tension: It is natural for springs to lose tension. Should the door become hard to operate or completely inoperative, contact a door professional. d. Guide Tracks: Clean the internal sections of the guide tracks every 3 - 6 months with a cloth dampened with mineral turps or methylated spirits. 8.2 If You Need a Service Call If the opener needs a service please call the dealer who installed the garage door opener (their contact details are usually on a sticker on the back of your garage door). BEFORE CALLING you should have the following information to assist in providing the appropriate service:

1. Has anything happened since the opener last operated OK, e.g. a storm, a jolt to the door etc.?

2. What is the current light status on the opener?

3. Manually disengage the door (Section 5). How easy is it to manually open and close the door?

4. What model is the opener? (Model no. information is located at the rear 5. Who installed the opener? (Dealer details should be on a sticker on the of the opener) back of your garage door) 6. When was it installed? (If known) 30 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 9. Appendix A - Status Indication during Operating Mode. LEDs Light Status Description BLUE GREEN YELLOW RED PURPLE DOOR OPEN 2 AND CLOSED 1 LEDS solid flashing flashing solid flashing flashing flashing solid solid MODE LED 3 BATTERY LED 4 REMOTE CONTROL STATUS LED 5 NETWORK LED 6

(ATS-3 Only) 1 flash then pause 2 flashes then pause solid flashing flicker alternate 02 06 Open Open with Autoclose timer running Opening / Obstructed on Open Closing / Obstructed on Close Closed Stopped Partial Open Load Diagnostics mode Battery not used / not fitted Battery charged in use (holding STOP for 10s will shutdown) Battery charging, when connected to power Battery failed / fault Remote lockout Remote Control Activity flashing Hot Spot Turning On solid Hot Spot Active Connecting to Wi-Fi Connected to Server Connected to Cloud Software Updatingr Status update / Command received Wi-Fi Disabled Rebooting Requires confirmation from user 03 04 flashing off solid flash 2 secs flashing rapid flashing flashing rapid flashing On flashing alternate 01 05 31 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 B - Adjustment Mode Instructions a. Press the MODE button repetively until the GEAR LED starts flashing b. Referring to the table below, select the desired parameter using the OPEN and CLOSE buttons and observing the number of flashes on the GEAR LED. The selected parameters value is indicated by the main lights brightness. c. Press STOP / SET button to start editing the parameters value. The TRANSMIT LED will turn on when editing is active. d. Use the OPEN and CLOSE buttons to step through the available options. The lights brightness will change accordingly. tip Pressing the MODE button when a parameter is being adjusted will load the default value. e. Press STOP / SET button to save the parameters new value or press MODE to leave the value unchanged. f. Continue from a. above to select another parameter or press MODE to exit adjustment mode. Value options = Indicated by brightness of main light

(DEFAULT parameter underlined) tip Flashes 2 3 4 5 1.2A 1.4A 1.6A 2.0A PE AUTO-CLOSE 15sec 30sec 60sec 90sec 6

15sec 30sec 60sec 90sec 120sec 30sec 60sec 90sec 120sec 180sec 240sec 1 1.0A OFF OFF Mimic light x1 x2 x3 x4 x5 x6 1sec 30sec 60sec 120sec 180sec 240sec 300sec 600sec toggle OPEN/STOP/CLOSE DOOR OPEN/HOLD OPEN When parameter edit mode is active, if any button other than MODE is pressed, then when MODE is pressed again, operating mode will be selected instead of the NETWORK adjustment mode. Parameter Name MARGIN AUTO-CLOSE LIGHT TIMER AUX OUTPUT OSC INPUT AUX OUPUT Configures how the AUX Output operates. If configured for Mimic light mode then the AUX output will activate whenever the main light output is on. All other settings require either a remote control code set to the AUX function or the Phone App to be used to activate the output. The time settings option indicate how long the output will remain on when triggered. If the output is already on then a 2nd trigger will turn the output off. The toggle On/Off setting does not use a timer and the output simply changes state on each trigger. OSC Output By default the OSC input is used to open, close or stop the doors movement. When DOOR OPEN/ HOLD OPEN is selected activating the OSC input will open the door. If the input is held active then the door will not be able to be closed until after the input is released. 32 ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual C - Adjusting Force Margins Adjusting Safety Obstruction Force The Safety Obstruction Force is calculated automatically during setup. Adjusting this is normally only necessitated by environmental conditions such as windy or dusty areas, and areas with extreme temperature changes. To Increase / Decrease Force Pressure a. Press the MODE button repetitively until the GEAR b. The LED will start flashing with one flash every second. c. Press the STOP / STEP button and the MODE button LED and the TRANSMIT LED is flashing. LED will be lit and the GEAR LED will flash once every second. d. By pressing the OPEN button will increase the force pressure and CLOSE button pressure is decreased or increased. will decrease the force - Main light will dim or brighten as the e. Press STOP / SET button to save the new value. (Refer to Appendix B for margin settings) f. Test the force again as per Testing Close Cycle and Testing Open Cycle. D - Battery Functions minimum. a. Holding the STOP button for 10secs when running from battery backup will shut the PCB down so as to reduce battery current consumption to a b. Holding the STOP button for 4secs when a battery is fitted and running from mains power will cause the controller to test the battery state to determine if it is disconnected / open circuit, missing, faulty or ready. E - Setting up Tilt Door Prior to limit set up, the opener can be set to J-Type Tilt Profile. This process allows the opener to pre-set to J-Type settings where the limit is not greater than 1500mm. If J-Type is selected, the speed is customised and cannot be changed. a. Press the MODE button repetitively until the GEAR b. Press and hold STOP / SET button for 2 seconds to check the door type, until the main courtesy light turns solid ON or OFF. LED starts flashing. Main courtesy light ON - Tilt type (J-Type only) Main courtesy light OFF - Sectional type c. Press and hold STOP / SET for 6 seconds to change the door type, until the main courtesy light turns solid ON or OFF. If required, repeat step b to check the door type selected. d. Press MODE button to exit the door selection mode. Proceed to Section 6.4 to set the limits. 33 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 F - Setting the PET Mode position When activated, PET mode drives the door to a preset position from the close position, therefore allowing a pet or parcel to go under the door. a. Drive and stop the door at the desired PET mode open position by pressing the transmitter button coded for Open/Stop/Close operation. b. Press the MODE button repetitively until the GEAR LED is lit. c. Press OPEN button to save PET position - Main light will flash and both OPEN and CLOSE LED will light up. G - Setting limits via Premium Remote Control Button 1

(inch Open) Button 2 (Set) Button 4

(inch Close) a. Switch power on and the BLUE LED on the CLOSE button will start to flash to indicate that the opener is ready to set the Close travel limit b. Press the MODE button repetitively until the TRANSMIT LED is lit. c. Press and HOLD the CLOSE button to set the Open / Stop /

Close function. The Main light will start to flash rapidly. d. Press and hold button 1 on the Premium Remote Control, then release remote control button. e. Press and hold button 1 on the Premium Remote Control button again until the main light stops flashing rapidly. f. Release both buttons. The remote control button is now coded, press to test and observe the speed of the door through a full cycle. g. The drive speed is set to the fastest setting by default. This may not be suitable for larger doors or for single piece doors:

(ii) While

(i) Using the programmed Premium Remote Control, press and hold the button 4 to close. To inch the door, single presses of the button 4 will move the door to desired limit.

(to CLOSE) the close speed, press the and hold button 4 on SET button 2 the opener will cycle through all three speed modes as shown in table. remote and by pressing to set inching the

(iii) Once at the desired speed, release the remote button 4.

(iv) Continue inching the door to the desired position. We recommend the CLOSE limit position being the first point of contact of the rubber strip (

at the bottom of the door) with the ground.

(v) If the door overshoots, press the OPEN button 1 on the remote to move the door in the OPEN direction.

(vi) When the door is at the desired CLOSE position, press the SET button 2, the GREEN LED on the OPEN button will now flash. CLOSE limit:

OPEN limit:

34

(i) Using the programmed Premium Remote Control, press and hold the button 1 to open. To inch the door, single presses of the button 1 will move the door to desired limit.

(ii) While inching

(to OPEN) to set the open speed, press and hold button 1 on the remote and by pressing the SET button 2 the opener will cycle through all three speed modes as shown in table.

(iii) Once at the desired speed, release the remote button 1.

(iv) Continue inching the door to the desired position. We recommend the OPEN limit position being the height of the garage opening

(v) If the door overshoots, press the CLOSE button 4 on the remote to move the door in the CLOSE direction. WARNING! The door will automatically close, open and close again after the next step. Ensure that nothing is in the doors path. AVERTISSEMENT: La porte va se fermer puis souvrir automatiquement, avant de se fermer. Sassurer que rien ne bloque louverture ou la fermeture de la porte.

(vi) When the door is at the desired OPEN position, press the SET button 2. The door will now automatically close and open to calculate the safety obstruction settings. ATS-3AM & ATS-2AM Dominator Tempo & Syncro Instruction Manual 35 Diamond PD Power Drive : Instruction ManualDominator Tempo & Syncro Instruction Manual ATS-3AM & ATS-2AM Copyright 2019 Automatic Technology America3626 North Hall Street, Suite 610, Dallas, TX 75219, United States of AmericaP: +1 800 934 9892 W: www.ata-america.com

1 2 3 4 5 6 A B C D LIGHT GREY: BACKGROUND AUTOMATIC TECHNOLOGY AMERICA RESIDENTIAL GARAGE DOOR OPERATOR MODEL: ATS-3AMB 120V INPUT VOLTAGE:

60Hz FREQUENCY:

2.0A CURRENT (MAX):

CONFORMS TO ANSI/CAN/UL 325 TESTED TO COMPLY WITH PART 15 OF THE FCC RULES 4008033 WARNING / AVERTISSEMENT THIS UNIT IS NOT USER SERVICEABLE, DISCONNECT POWER SUPPLY BEFORE REMOVING COVER. PLEASE ENSURE THAT THE POWER CORD IS SECURED, CLEAR OF ANY MOVING PART OF THE OPENER AND DOOR. FAILURE TO COMPLY MAY DAMAGE CORD AND CAUSE ELECTROCUTION. CET APPAREL NEST PAS REPARABLE PAR LUTILISATEUR, AVANT DE RETIRER LE CAPOT, DEBRANCHEZ LE CORDON ELECTRIQUE, ASSUREZ-VOUS QUIL NE RISQUE PAS DENTER EN CONTACT AVEC DES PIECES EN MOUVEMENT LE NON-RESPECT DE CES INSTRUCTIONS PEUT AVOIR UNE ELECTROCUTION POUR CONSEQUENCE. MANUFACTURING DATE:

ata BIN #

87398 AUTOMATIC TECHNOLOGY AMERICA RESIDENTIAL GARAGE DOOR OPERATOR MODEL: ATS-3AMB 120V INPUT VOLTAGE:

60Hz FREQUENCY:

2.0A CURRENT (MAX):

CONFORMS TO ANSI/CAN/UL 325 TESTED TO COMPLY WITH PART 15 OF THE FCC RULES 4008033 WARNING / AVERTISSEMENT THIS UNIT IS NOT USER SERVICEABLE, DISCONNECT POWER SUPPLY BEFORE REMOVING COVER. PLEASE ENSURE THAT THE POWER CORD IS SECURED, CLEAR OF ANY MOVING PART OF THE OPENER AND DOOR. FAILURE TO COMPLY MAY DAMAGE CORD AND CAUSE ELECTROCUTION. CET APPAREL NEST PAS REPARABLE PAR LUTILISATEUR, AVANT DE RETIRER LE CAPOT, DEBRANCHEZ LE CORDON ELECTRIQUE, ASSUREZ-VOUS QUIL NE RISQUE PAS DENTER EN CONTACT AVEC DES PIECES EN MOUVEMENT LE NON-RESPECT DE CES INSTRUCTIONS PEUT AVOIR UNE ELECTROCUTION POUR CONSEQUENCE. MANUFACTURING DATE:

ata BIN #

87398 O N L A R E S I O N L A R E S I NOTE: ALL TEXT & ARTWORK COLOURS ARE BLACK UNLESS OTHERWISE SPECIFIED PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF AUTOMATIC TECHNOLOGY AUSTRALIA Pty Ltd. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF AUTOMATIC TECHNOLOGY AUSTRALIA Pty Ltd. IS PROHIBITED. GENERAL TOLERANCES:

TITLE:

DECIMAL: 0.X 0.1 0.XX 0.05 ANGLE: 0.5 RADIUS: 0.5 CHAMFER: 0.5 x 45 SURFACE FINISH DEBUR AND BREAK SHARP EDGES LEXAN 8B35 0.18THK 9495MP ADHESIVE BACKING 1 DESCRIPTION QTY MAT'L REMARKS Automatic Technology Australia Pty Ltd. 6-8 FIVEWAYS BOULEVARD, KEYSBOROUGH, VIC, 3173, AUSTRALIA PHONE: +61(0) 3 9791 0200 FAX: +61(0) 3 9791 0250 WEB: www.ata-aust.com.au WARNING INFO LABEL_ATS-3AMB NAME DATE G.GAFF 22/03/21 DOCUMENT NO. 160733_00 SCALE:

PART NO. 1 : 1 87471 SHEET A4 1 2 3 4 5 6 A B C D LIGHT GREY: BACKGROUND ata Auto-Ki FCC ID: X4K-ATS3DCB11WS IC: 8880A-ATS3DCB11WS WARNING / AVERTISSEMENT This device complies with FCC Part 15 and or RSS 210 Innovation, Science and Economic Development Canada Rules. Adjustment or modifications of this device (receiver/transmitter) are prohibited, except for changing the code setting or replacing battery. This device contains licence-exempt transmitter(s) /

receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device may not accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme la partie 15 de la FCC et ou aux rgles RSS 210 Innovation, Science et Dveloppement conomique Canada. Le rglage ou les modifications de cet appareil (rcepteur/metteur) sont interdits, sauf pour changer le rglage du code ou remplacer la pile. Cet appareil contient un metteur(s)

/ rcepteur(s) exempt de licence qui est conforme aux RSS(s) exemptes de licence d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est assujetti aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interfrences nuisibles, et (2) cet appareil ne peut accepter aucune interfrence, y compris celles qui peuvent provoquer un fonctionnement indsirable de l'appareil. 25 145 ata Auto-Ki FCC ID: X4K-ATS3DCB11WS IC: 8880A-ATS3DCB11WS WARNING / AVERTISSEMENT This device complies with FCC Part 15 and or RSS 210 Innovation, Science and Economic Development Canada Rules. Adjustment or modifications of this device (receiver/transmitter) are prohibited, except for changing the code setting or replacing battery. This device contains licence-exempt transmitter(s) /

receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device may not accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme la partie 15 de la FCC et ou aux rgles RSS 210 Innovation, Science et Dveloppement conomique Canada. Le rglage ou les modifications de cet appareil (rcepteur/metteur) sont interdits, sauf pour changer le rglage du code ou remplacer la pile. Cet appareil contient un metteur(s)

/ rcepteur(s) exempt de licence qui est conforme aux RSS(s) exemptes de licence d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est assujetti aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interfrences nuisibles, et (2) cet appareil ne peut accepter aucune interfrence, y compris celles qui peuvent provoquer un fonctionnement indsirable de l'appareil. NOTE: ALL TEXT & ARTWORK COLOURS ARE BLACK UNLESS OTHERWISE SPECIFIED PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF AUTOMATIC TECHNOLOGY AUSTRALIA Pty Ltd. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF AUTOMATIC TECHNOLOGY AUSTRALIA Pty Ltd. IS PROHIBITED. GENERAL TOLERANCES:

TITLE:

DECIMAL: 0.X 0.1 0.XX 0.05 ANGLE: 0.5 RADIUS: 0.5 CHAMFER: 0.5 x 45 SURFACE FINISH DEBUR AND BREAK SHARP EDGES LEXAN 8B35 0.18THK 9495MP ADHESIVE BACKING 1 DESCRIPTION QTY MAT'L REMARKS Automatic Technology Australia Pty Ltd. 6-8 FIVEWAYS BOULEVARD, KEYSBOROUGH, VIC, 3173, AUSTRALIA PHONE: +61(0) 3 9791 0200 FAX: +61(0) 3 9791 0250 WEB: www.ata-aust.com.au ATS-3AM FCC STATEMENT LABEL NAME DATE G.GAFF 16/03/21 DOCUMENT NO. 160767_00 SCALE:

PART NO. 1 : 1 TBA SHEET A4

24 February 2021 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: X4K-ATS3DCB11WSS Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Operational Description File Name CONF_ATS-3AM(B)_Blkdia.pdf CONF_ATS-3AM(B)_Schem.pdf CONF_ATS-3AM(B)_OpDes.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Nikolai Klepikov Senior Electronics Design Engineer

EMC Technologies Pty Ltd ABN 82 057 105 549 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph: + 613 9365 1000 Fax: + 613 9331 7455 Email: [email protected] To:

Attention:

EMC Ref:

Subject:

Federal Communications Commission/

ISED Canada Certification Bureau Certification Officer Date:

June 24, 2021 M2010040 Certification Original filing (FCC ID: X4K-ATS3DCB11WS)

- Single Certification (IC: 8880A-ATS3DCB11WS) Automatic Technology (Australia) Pty Ltd FCC ID: X4K-ATS3DCB11WS IC: 880A- ATS3DCB11WS DOMINATOR SYNCRO Automatic Garage Door Operator Company:

FCC ID:

IC ID:

EUT:

Automatic Technology (Australia) Pty Ltd is applying for FCC Original certification for the DOMINATOR SYNCRO Automatic Garage Door Operator. The EUT contains:

FHSS Transmitter (902-928 MHz):

DSS 2.4 GHz WiFi Transmitter (2412-2462 MHz): DTS DSS: FHSS Transmitter EMC Technologies test results and reports have been provided for the DSS portion of this filing. DTS: 2.4 GHz Wi-Fi The 2.4 GHz WiFi was previously certified by Automatic Technology (Australia) Pty Ltd:

FCC ID: X4K-WSS33-1, IC: 8880A-WSS33. The Equipment authorization was granted on 01/23/2019. Since this approval, the grantee Automatic Technology (Australia) Pty Ltd has declared that no hardware design or software changes (to increase RF output power) have been made to the WiFi and that the antenna condition (FPCB with 1dBi gain) also has not changed. As no changes have been made which could degrade the original 2.4 GHz WiFi test results, the test reports previously submitted for FCC and ISED Canada approval (FCC ID: X4K-WSS33-1, IC:

8880A-WSS33) are therefore applicable to demonstrate compliance with the FCC and ISED Canada radio requirements of the DTS portion of this application without further testing. As per the requirements of KDB 484596 D01 Referencing Test Data v01, Section 1), c) spot check measurement results have been provided to demonstrate that the referenced test data remains valid. Please refer to Report Number M2010040-4 RDO SpotCheck.pdf. EMC Technologies Pty Ltd, 176 Harrick Road, Keilor Park VIC 3042 Australia www.emctech.com.au EMC Technologies Pty Ltd is acting as agent for Automatic Technology (Australia) Pty Ltd in this application. Best Regards _____________ Chris Zombolas Technical Director EMC Technologies Pty Ltd 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph: +61 3 9365 1000 www.emctech.com.au EMC Technologies Pty Ltd, 176 Harrick Road, Keilor Park VIC 3042 Australia www.emctech.com.au

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 24 February 2021 SUBJECT: FCC Application for FCC ID: X4K-ATS3DCB11WSS To Whom It May Concern:

We, the undersigned, hereby authorize Chris Zombolas at EMC Technologies Pty Ltd on our behalf, the Federal Communications Commission on our equipment. Any and all acts carried out by Chris Zombolas on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Nikolai Klepikov Senior Electronics Design Engineer to apply to