FCC ID: 2AL4G-004 Intelligent Toilet

REV. DESIGN DATE CONTENTS MARK QTY. 01 20250304 m m 0 1 2 MINT TWO TS036 TS036 USER MANUAL 142.5 mm TYPE TS036 1. 2. 142.5210mm 1mm 3. 4. 5. RoHS DESIGN CHECK PROCESS STANDARDIZE APPROVE 20250304 MATERIAL SIZE 120g A4 SCALE UNIT 12 mm TITLE PART NO. 224000207500 SHEET 1 OF 1 XIAMEN AXENT CORPORATION LIMITED MINT TWO TS036 TS036 USER MANUAL THANK YOU Thank you for selecting an AXENT Switzerland product. To ensure proper installation, please review these instructions carefully before use. Carefully unpack and examine the intelligent toilet before installa-

tion. For any questions, contact us at 1-949-250-4576. Thank you again for choosing AXENT. BEFORE YOU BEGIN CAUTION!

Risk of personal injury or product damage Handle with care. Vitreous china can break or chip if handled carelessly. All installation procedures should comply with applicable local plumbing and building codes. I N STA L L AT I O N B Y A P R O F E S S I O N A L , LICENSED PLUMBER OR CONTRACTOR IS HIGHLY RECOMMENDED. USER MANUAL MINT TWO Safety Introduction Multi-function dial Remote Control Maintenance Troubleshooting Technical data Guarantee 1 5 6 8 13 16 21 22 SAFETY SAFETY SYMBOLS The following symbols in the manual will highlight hazardous situations and their severities. DANGER!

High Risk, Lethal Hazards, Severe Injuries WARNING!

Medium Risk, Severe Injuries CAUTION!

Low Risk, Minor Injuries NOTE!

Damage to Property NORMAL USAGE The intelligent toilets spray arm attachment should only be used for the rear wash and front wash clean-

ing functions. The product may also be used as a normal toilet seat. This product is meant for indoors usage only. Any other usage will not be deemed as normal usage. AXENT undertakes no liability for abnormal usage. AXENT is not liable or responsible for damage to other electronics connected to the same power line while the intelligent toilet is in use. IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING SAVE THESE INSTRUCTIONS A copy of the instructions can also be downloaded from https://axentbath.us. When using electrical products, especially when children are present, basic safety precautions should always be taken, including the following:

DANGER!

To reduce the risk of electrocution Do not reach for any electrical components of the intelligent seat that have fallen into water. Unplug toilet immediately. Unplug product if not in use for extended periods of time. Do not use while wet after bathing. Do not place or store product where it can fall or be pulled into a tub or sink. Do not place or submerge the intelligent toilet or its components into water or other liquids. 1 SAFETY WARNING!

To reduce the risk of burns, electrocution, fire, or injury to persons. Children or disabled persons may require supervision during use. Use this product only for its intended use as described in this manual. Do not use attachments not authorized by the manufacturer. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair. Keep the cord away from heated surfaces. Do not block the air vents on this product. Do not place the toilet on or by objects such as long window curtains that could potentially obstruct the air vents during normal usage. Keep air vents free of lint, hair, and other debris. Never use while sleepy or drowsy. Never drop or insert any object into any openings or hoses. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. Connect this product to a properly grounded outlet only. See Section Grounding instructions on next page. Unplug this product before filling water. Fill (reservoir) with water only unless otherwise specified by manufacturer. Do not overfill. SAFETY INSTRUCTIONS Carefully read and observe the following safety instructions!

Information for the user Children or persons with limited physical/mental capabilities may require supervision or proper in-

structions/guidance prior to or during use. Ensure that children cannot play with intelligent toilet. Avoiding malfunctions and damage to the product as a result of improper use If intelligent toilet is moved from a cold location to a warm location, condensation may form. Leave the unit switched off for a few hours. Do not install the intelligent toilet in rooms where the temperature will be less than 4 C ( 39 F ). Do not place open flames, candles, cigarettes, or similar objects on or by the toilet. Do not reuse old hoses or water lines. Please use new water lines when installing. Do not install the intelligent toilet next to items that would potentially expose the toilet to a large amount of water. Do not climb on or stand on the product. 2 SAFETY Do not place any heavy objects on the lid. Do not open or close the lid or seat with force. Do not deliberately soil, spray or block the spray arm. Repairs should only be carried out by a person with the necessary expertise Do not carry out modifications, tamper with, install additional equipment, or attempt to repair the intel-

ligent toilet. Improperly performed repairs can lead to accidents, injuries, or damage to the product. Only use the device when it is fully functional Make sure the power cable is not damaged before use. Do not allow the power cable to be severely pinched, bent, or kinked. Keep the power cable away from hot surfaces and sharp edges. Do not handle the power cord or plug with wet hands. Do not use the product if it is not working properly. In case of malfunction, disconnect the power im-

mediately. Close the water cut-off valve to interrupt the water supply. Contact your installer. Information on the use of batteries Keep batteries out of the reach of small children. Batteries can be life-threatening if swallowed. If a battery has been swallowed, seek medical assistance immediately. Do not attempt to recharge non-chargeable batteries for use with unit. Always remove empty batteries from the remote control immediately. They may leak and cause damage. Do not insert new and old batteries together in the remote control. Clean the battery and contacts before inserting the battery. Make sure the batteries are oriented properly. Remove the batteries if the remote control will not be used for an extended period of time. Do not expose the batteries to hot surfaces or direct sunlight to reduce the risk of battery leakage. If battery acid has leaked, avoid contact with skin, eyes and mucous membranes. In case of contact with the acid, flush the affected areas with large amounts of clean water and seek medical assistance immediately. GROUNDING INSTRUCTIONS This product must be grounded when plugged in. The power cord on this product has a grounding plug and must be plugged into an outlet with a properly grounded grounding plug. DANGER!

Improper use of grounding plug can result in a risk of electric shock. For safety, the intelligent toilet should be plugged into a standard 3 prong GFCI outlet. 3 SAFETY Grounded outlet Grounding pin Grounded outlet box Wiring Diagram (NOT FOR INSPECTORS USE) If repair or replacement of the power cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. This product is not to be used with extension cords. This product is factory equipped with a specific electric cord and plug to permit proper connection. No adapters should be used with this product. Do not modify the power cord on the toilet. If the pow-

er cord will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel. Please unplug unit immediate and contact for service if cord becomes damaged. Do not use a bidet seat with a damaged cord. NOTE!

Actual installation may differ slightly from the diagram. FCC INSTRUCTIONS Please note that changes or modifications not expressly approved by the party responsible for compli-

ance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Please contact support team at [email protected] or 949-250-4576. RF exposure statement: This equipment complies with radio frequency exposure limits set forth by the FCC for an uncontrolled environment. This intelligent toilet [TS036-3] should be installed and operated with a minimum distance of 0.02 m between the device and the user or bystanders. This device must not be co-located or operating in conjunction with any other antenna or transmitter. 4 INTRODUCTION OVERVIEW Open Close ECO Seat Temp F Status Display Air Temp When the water temperature is turned off, the [Status Display] shows 00. MAIN Lid Rear cover Manual Flush Button Multi-function Dial MULTIFUNCTION DIAL Nozzle Seat Press Turn counter clockwise Turn clockwise 5 MULTI-FUNCTION DIAL MAIN Function Button Operation Notes MAIN Press the button again to stop the Wash early. If not stopped manu-

ally the Wash will stop automatically after 3 minutes. If not stopped manu-

ally the Rear Wash /

Front Wash will stop automatically after 3 minutes. As soon as you sit down on the toilet seat, the spray arm will be cleaned with fresh water. Flush Press Manual Flush Button to start. Rear Wash Front Wash After you are seated, Turn the Multifunction dial counter clock-

wise to start. After you are seated, Turn the Multifunction dial clockwise to start. During Rear or Front Wash, Turn the Multifunction dial clockwise to increase the water flow. Water Flow

During Rear or Front Wash, Turn the Multifunction dial counter clock-

wise to reduce the water flow. 6 MULTI-FUNCTION DIAL Function Button Operation Notes MAIN Foam shield Stop Stand-by Mode Press the Multifunction dial to activate the foam anti-splash function.

Press and hold the Multifunction dial for 5 seconds to turn the Foam shield function on or off Factory setting: OFF When the setting is turned on, the Foam shield function will auto-

matically start after you are seated. When the washing process is active or the setting mode is active, Press the Multi-function dial to stop the ongoing function.

Press the Multifunction dial for about 10 seconds to activate Stand-By mode.

- Sit on or touch the sensing area of seat to deactivate Stand-by mode. In Stand-by mode, all functions of the toilet will be deactivated until Stand-by mode is deactivated. 7 REMOTE CONTROL REMOTE CONTROL Open Close When receiving remote control command, the main unit makes the following sound:

One short beep effective command Two short beep ineffective command One long beep exceed the range of remote control Low battery will effect the use of remote control, please replace batteries in time. Function Button Operation Notes REMOTE CONTROL Turn On Turn Off

Pairing Stop 8 Install batteries to turn on remote control. Remove batteries to turn off remote control. Remove all batteries of remote control, and cut off the power of the intelligent toilet, wait for 30 seconds, and then reapply power. After three times short beep and the night light flashes, you are now in Pairing mode. Install batteries immediately. start pairing by pressing Stop repeatedly until hearing feedback from the intelligent toilet, which means pairing succeeded. When night light stops flashing, the system exit Pairing mode.

- If remote control works but does not con-

trol toilet, which means pairing is unsuc-

cessful, please perform the Pairing again. Please do not insert new and old batteries together. Pairing has originally been done in the factory. It is only necessary after the remote control has been replaced. Please make sure there is sufficient power supply for the remote control before pairing. REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Auto Open When someone approaches, The lid and seat will automatically open according to Auto Open Setting.

- Auto Open only works when the lid is closed.

- The seat will only open automatically after being closed for more than 10 sec-

onds. Please find more infor-

mation about Auto Open Setting on page 12. Opening and Closing the Seat and Lid When the unit is not in use, Auto Close Seat and lid will be closed automatically af-

ter leaving the sensing area of the intelligent for about 2 minutes. Open/Close When someone approaches, Press Open/Close to switch between :

- Open lid

- Open seat

- Close seat and lid Press Flush to start. Flush

Flush Auto Flush After being seated for more than 15 sec-

onds, the function will be started after a period of time defined by the Auto flush setting which defaults to 15 seconds. Rear Wash Front Wash After you are seated, Rear Wash Press Rear Wash to start. After you are seated, Front Wash Press Front Wash to start. Oscillating and Pulsating Shower Massage During Rear or Front wash, Press Massage to switch between:

- Oscillating

- Pulsating

- Oscillating and Pulsating

- OFF The seat will only flush after being closed for more than 10 seconds. Please find more informa-

tion about Auto Flush After Leaving setting on page 12 . If not stopped manually the Wash will stop automatical-

ly after 3 minutes. After you are seated, the toilet will automatically clean the nozzle once.

9 REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Dry After you are seated, Dry Press Dry to activate the dryer. I t i s re c o m m e n d e d to wipe off most of the water with a paper towel before activating the dryer. Nozzle UVGI

When the unit is not in use, Nozzle UVGI will be automatically activated

- The sterilization function will stop automatically after running for about 2 minutes. If someone is seated during the function operation, the uv sterilization function will stop running immediately. Press Foam shield to activate the foam anti-splash function. Foam shield Foam shield After you are seated,

The foam anti-splash function will be acti-

vated automatically. Please find more informa-

tion about Foam shield Setting on page 11. Stop Stop Press Stop to stop the function in pro-

gress. Press Stop for more than 3 seconds to exit the Settings mode The Settings mode is ter-

minated automatically after 20 seconds of inactivity. During Rear or Front wash, Increase Press Water Volume to adjust the water volume.

- Press Increase to increase the water volume.

- Press Reduce to reduce the water Reduce volume. During Rear or Front wash, Increase Press Position to adjust the position of the spray arm.

- Press Increase to move the Spray Arm forward.

- Press Reduce to move the Spray Arm Reduce backward. Water Flow Water flow Spray Arm Position Position 10 Level Indicator indicates the selected level. REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Seat Temp Press Seat Temp to activate tempera-

ture adjustment. Increase

- Press Increase to increase the tem-

Seat Temp perature.

- Press Reduce to reduce the temper-

Reduce ature. Water Temp Water Temp Air Temp Air Temp During Rear or Front wash, Increase Press Water Temp to activate tempera-

ture adjustment.

- Press Increase to increase the tem-

Reduce perature.

- Press Reduce to reduce the temper-

ature. During Dry, Increase Press Air Temp to activate temperature adjustment.

- Press Increase to increase the tem-

perature. Reduce

- Press Reduce to reduce the tem-

perature. Level Indicator indicates the selected level. All indicators go off means the heating function is turned off. Foam shield Setting Foam shield Press Foam shield for about 3 seconds to enter into the Setting. Factory setting:OFF Repeat the operation to switch between:

- OFF

- ON One indicator remains on;

Five indicators remain on. Level Indicator indicates the selected level. Smart Night Light Light Press Light to turn on or turn off the smart night light.

- AUTO Short beep ;

Long beep ;

- ON Long beep .

- OFF Factory setting: ON When the setting is Auto, smar t night light turns ON or OFF automatically according to ambient light levels. Signal Tone Setting Stop Water Temp Press Stop at the same time Water Temp for about 3 seconds to turn the function on or off.

- ON

- OFF Non-prompt tone ;

One short beep. Factory setting: ON When the setting is OFF, the system shut down all prompt sounds. 11 REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Deodorize Set-

ting Stop Water Flow Press Stop at the same time Water Flow for about 3 seconds to turn the function on or off.

- ON

- OFF Short beep ;

Long beep . Factory setting: ON When the setting is on, the deodorizer function is activated when a user is seated. Eco Setting Stop Seat Temp Press Stop at the same time Seat Temp for more than 3 seconds to turn the function on or off. Short beep ;

- ON

- OFF Long beep . AUTO Temp Setting Stop Air Temp Press Stop at the same time Air Temp for about 3 seconds to turn the function on or off.

- ON

- OFF Short beep ;

Long beep . Auto Open Setting Stop Position Open/Close Press Stop at the same time Position for about 3 seconds to enter into the Set-

ting. Press Open/Close to switch between:

- OFF

- Lid

- Seat One indicator remains on;

Three indicators remain on;

Five indicators remain on. Stop Flush Auto Flush After Leaving Setting Increase Reduce Press Stop at the same time Flush for about 3 seconds to enter into the Setting. Press Increase or Reduce to switch between:

- OFF

- 5 seconds One indicator remains on;

- 10 seconds Three indicators remains on;

- 15 seconds five indicators remains on. All indicators off;

12 Factory setting: OFF When the ECO setting is on, the seat will be intelli-

gently heated according to the users usage habits. Factory setting: ON In this mode, the system will learn by itself, so that the seat temperature, air temperature and water temperature can be adjust-

ed intelligently according to the change of environmen-

tal temperature. In order to ensure the use effect, please turn off the Eco function when turning on this function. Factory setting: Lid Level Indicator indicates the selected level. L i d m o d e : O n l y l i d i s opened. Seat mode: Lid and Seat are opened. Close mode: Close the Auto Open function. Factory setting: 15 seconds MAINTENANCE FOAM SHIELD FILLING DIAGRAM Press the Multifunction dial for about 10 seconds to activate Stand-By mode, prior to adding liquid detergent in order to avoid any interference caused by the cover during the replacement process. Grab both sides of the rear decorative cover and pull up. Add the right amount of liquid detergent to the detergent box to prevent overflow. If there is an overflow, clean it with a soft damp cloth. 1. Please use a liquid detergent that can produce a large amount of bubbles when mixed with water. The foaming effect and duration of foam shield vary when using different brands of liquid detergent. 2. When the ambient temperature drops below 6 C, it is advisable to utilize a blend of liquid detergent and water in a ratio of 5:1 to pre-

vent freezing caused by excessively low temperatures, which may compromise its efficacy. The rear decorative cover should be aligned with the card slot and placed down. Once the magnet is attached, the foam protector can be used. REPLACE BATTERIES Remove old batteries Insert new batteries

AAA AAA

AAA AAA

AAA AAA

13 MAINTENANCE SPRAY ARM CLEANING When the unit is not in use, Turn the multifunction dial counter clockwise to extend the spray arm for cleaning. Clean the spray arm with a fabric or a soft bristle brush. Turn the Multifunction dial counter clockwise again to retract the spray arm. FILTER CLEANING Coin or Similar The filter screen will need to be cleaned frequently. If the unit does not fill up properly, starts to lose pressure, or has no function normally, please clean the filter first. 2 DO NOT use the product without the filter. Otherwise the product may not be warranty. The water inlet valve must be shut off during the entire filter cleaning process. Inlet Valve The filter may be reinserted in reverse after cleaning. Filter 14 MAINTENANCE SUITABLE CLEANING DETERGENTS

- Mild bathroom or all-purpose cleaner

- Mild detergents

- Normal toilet brushes

- Soft sponges

- Microfiber cloth CLEANING INSTRUCTIONS SEAT, LID AND BACK COVER Use a mild soap solution to clean the seat. Please take care that the seat and hinges are not left damp. Dry off any residual water or cleaning agent with a soft cloth. Ensure that the seat and seat hinges do not come in contact with abrasive, corrosive, or chlorine-based cleaners, as these may cause damage or lead to flash rust. When cleaning the bowl, make sure that the seat and cover are kept in an upright posi-

tion until all cleaning agent has been flushed away. DISCONNECT THE MAIN PLUG BEFORE YOU START WITH CLEANING THE PRODUCT. Do NOT use any scouring equipment or tools (ex: scouring pad) or any aggressive cleaning agents for cleaning. CLEANING CERAMIC APPLIANCES Do not use harsh or abrasive cleaning substances such as abrasive cleansers, scouring powder or drain cleaner on your ceramic surfaces. Also avoid using steam cleaners and hard, abrasive sponges. Please do not pour or dispose of hair coloring products into the toilet as this can reduce the effectiveness of the AXENT Easy Clean coating. By following these maintenance guidelines, AXENT Easy Clean should remain effective for many years. AXENT highly recommends the use of acidic cleaners with a pH value between 1 and 4. Cleaners with a pH value in the neutral range (5 to 8) are not always suitable. We strongly advise against using either weak or strong alkaline cleaners, i.e. substances with pH values from 9 to 12. WINTERIZATION Please ensure water temperatures will not drop below 4 C (39 F). Frost or frozen water will damage the system and may lead to leakage. If the water or ambient temperature drops below 4 C (39 F), please discontinue use of product.

- Disconnect the electrical power.

- Shut off the water inlet valve.

- Disconnect the water inlet hose from the filter to drain out the water inside of the line.

- Press the Manual Flush Button. FAILURE TO DRAIN SYSTEM MAY RESULT IN DAMAGE TO SYSTEM AND LEAKAGE OR FLOODING. If the intelligent toilet is moved from a cold location to a warm location, condensation may form. Leave the unit switched off for a few hours before use. 15 TROUBLESHOOTING IN CASE OF THE FOLLOWING PHENOMENA, PLEASE CUT OFF THE POWER AND SHUT OFF THE WATER INLET VALVE IMMEDIATELY.

- Water leakage.

- Hearing continuous beep . PREPARE FOR CHECK Check the Power Supply

- If the power supply could work normally Check Water Supply

- If the water supply could work normally

- If the water inlet valve is shut off FREQUENTLY ASKED QUESTIONS In case of minor malfunctions, please refer to the following solutions. If the below solutions do not resolve the issue, please contact customer support for further examination and repair. MALFUNCTION CAUSE SOLUTION MAIN No function Product in Stand-by mode Sit on or touch the sensing area of seat to deactivate Stand-

by mode. REMOTE CONTROL Does not work Battery is low Wrong oriented Replace batteries. Reinstall batteries with correct oriented. Existing distractions Remove distractions. R e m o t e c o n t r o l works but does not control toilet The remote is disconnected from the toilet Please perform the Pairing (see page 8 for operation). Out of range Please use the remote control within the inductive distance. SEAT HEATER Low seat tempera-

ture Seat temperature set too low Increase seat temperature. Low seat temper-

ature when initially seated Seat temperature reduce automatically Eco mode is on Please exit Eco mode. Seat Low TEMP Protection will be activated automatical-

ly after Seated for a while It is normal. Please adjust Seat temperature or reseated to disable Seat Low TEMP Protection. And Seat Low TEMP Protection will be activated again after 5 minutes. High seat tempera-

ture Seat temperature set too high Reduce seat temperature. Seat temperature set too low Increase seat temperature. Heating error Disconnect the main plug and contact customer service. Seat heater does not work 16 TROUBLESHOOTING MALFUNCTION CAUSE SOLUTION MASSAGE Does not work Can only be activated dur-

ing the wash cycle Restart massage during Front or Rear wash. REAR WASH AND FRONT WASH Spray arm extend too slowly Low water pressure Self-cleaning before used Please be patient. Filter is blocked Clean filter. Connection loose Check connection between hose and main, and tighten it. Low water tempera-

ture Water temperature set too low Increase water temperature. Water stop sudden-

ly Leaving the seat During Rear or Front wash Seated and restart the washing. Spray arm extend w i t h o u t w a t e r spraying out Unstable water tem-

perature Seat does not sense per-

son Reconfirm position on seat. Water pressure is unstable Please turn off other water supplies, and wait for the water stable. OPENING AND CLOSING THE SEAT AND LID Auto Open does not work Auto open off Lid not closed Set Auto open as Lid or Seat. Close lid. Less than 10 seconds after last Auto Close Wait for 10 seconds after last Auto Close. Auto Close does not work The user still moving within the inductive distance Leave the inductive distance or be static for 2 minutes. Auto open set as Lid Set Auto Open as Seat. Seat does not open automatically Less than 10 seconds after last Auto Close Wait for 10 seconds after last Auto Close. DRY Dryer does not work Seat does not sense person Reconfirm position on seat. Low air temperature Air temperature set too low Increase air temperature. No air temperature Air temperature set off Increase air temperature. SELF-CLEANING Spray arm retracts automatically during Descale process Wand will automatically retract after 3 minutes of inactivity Restart Self-cleaning again. 17 CONTENT TROUBLESHOOTING MALFUNCTION CAUSE SOLUTION FOAM SHIELD Foam shield is acti-

vated, but no foam is coming out from the base nozzle. F o a m s h i e l d i s activated and only releases water or a small amount of foam. Filter is blocked Clean filter. Waterway of foam shield is blocked Other components mal-

function Disconnect the main plug and contact customer service. Disconnect the main plug and contact customer service. Liquid detergent has runs out Please refer to the instructions on page 13 for guidance on adding liquid detergent. Liquid outlet of detergent box is blocked The production of foam may significantly decrease when the room temperature drops below 6 due to the poten-

tial freezing of some liquid detergent Other components mal-

function Air is released when the foam shield is activated for the first time Disconnect the main plug and contact customer service. Please add an appropriate amount of warm water around 50to the detergent box (filling it up to about 90% capaci-

ty). Stir well and reactivate the Foam Shield several times to eliminate the freezing phenomenon. Disconnect the main plug and contact customer service. This is a normal phenomenon, and it will disappear after sev-

eral startup attempts. F o a m s h i e l d i s activated, the foam column becomes intermittently dis-

continuous If the foam shield is not activated for an extended period of time, the detergent may dry out, resulting in in-

termittent foaming when it is activated again It is a normal phenomenon. After adding liquid detergent again and letting it sit for a while, simply activate the foam shield several times to eliminate the issue. The flushing has been com-

pleted, and the product is still being refilled Please reactivate the Foam Shield after refilling. DEODORIZE Deodorizer does not work Deodorize off Please active Deodorize function. Seat does not sense per-

son Reconfirm position on seat. During Rear or Front wash It is normal. Deodorize is disable During Rear or Front wash. Deodorizer still runs after leaving seat The deodorizer continues to run for a while after leav-

ing the seat to increase effectiveness This is normal. 18 CONTENT TROUBLESHOOTING MALFUNCTION CAUSE SOLUTION NIGHT LIGHT Does not work Night light in OFF mode Switch night light setting to ON or AUTO mode. Night light in ON mode Switch night light setting to AUTO or OFF mode. Night light always on WARNING Light sensor blocked by object Remove distractions. Continuous beep Water temperature ex-

ceeds normal range Disconnect the main plug and contact customer service. 19 CONTENT TROUBLESHOOTING REPLACEMENT PARTS LIST Individual instructions will be included with applicable replacement parts. X10000003050 X10000003047(White) X10000003048(Black) X10000003049 Technical Unit Cover, Lid and Seat Cover Massage Dry Flush Open Close Mute Dry Flush Massage X10000003051 X10000002479 X10000003018 Remote Control Debris Filter Power Flush X10000003052 X10000002484 X10000002481 Toilet Bowl Bowl Mounting Hardware / Plug Inlet Hose X10000002483 X10000002482 Bowl Mounting support Base Mounting Hardware / Plug 20 TECHNICAL DATA Nominal voltage Power consumption Protection degree Water Volume Cable length 120 V~, 60 Hz 880 W IPX4 1.0 gpf/3.8 lpf 1.0 m ( 393/8 in) Minimum and Maximum pressure

(bidet portion only) 0.1 - 0.75 MPa ( 15- 108 psi ) Operating pressure (toilet) Refer to cistern specifications Ambient temperature range 4 - 40 C ( +39 to +104 F ) Water temperature range 4 - 35 C ( +39 to +95 F ) Product dimension ( L B H ) 683 385 491 mm ( 267/8 153/16 195/16 ) Maximum load (Seat and lid) 150kg ( 330lbs ) Max. flow rate rear wash Max. flow rate front wash Spray arm position Water temperature 600m L/min 600m L/min Ambient Temp, 31 - 39 C Air dryer temperature Ambient Temp, 30 - 50 C Seat temperature Ambient Temp, 29 - 37 C 5 levels 5 levels 5 levels 5 levels TECHNICAL SUPPORT For any questions or any assistance with this product, please contact your dealer or call us at 1-949-250-4576 [email protected] www.axentbath.us LEGAL DIRECTIONS This manual contains important information on the intended use, correct operation and proper maintenance of the equipment. Knowledge of and compliance with the instructions of this manual are provided for both the safe use of the equipment and for the safety of its operation and maintenance. In this manual, not all kinds of applications and improper manipulations are considered. In addition, attention is drawn to the following: The content of these instructions is neither part of any previous or existing agreement, commitment or legal relationship, nor does it change from an existing agreement, commitment or legal relationship. Any commit-

ment by AXENT results from the respective warranty. These include the complete and authoritative warranty obligation AXENT. The statements in this manual do not constitute an extension or a restriction of the claims under the warranty provisions. This manual is protected by copyright. Copies and / or translations into other languages may be made only with prior written approval of AXENT. 21 GUARANTEE AXENT LIMITED WARRANTY A three-year limited warranty applies to all AXENT products purchased on or after May 1, 2019. All prod-

ucts purchased on or before April 30, 2019 OR purchased for use in a commercial or hospitality setting on any date are backed by AXENTs one-year limited warranty. All spare parts purchased for use with Axent products are covered by a six (6) month limited warranty unless otherwise stated on the product. 1. AXENT warrants that its products are free from defects caused by defective material and faulty workmanship for a period of three-year from the date of purchase by the original purchaser. The limited warranty is to the original purchaser only. The limited warranty is not transferable to any third party. Proof of purchase showing both original ownership and purchase date is required for any warranty claim. The limited warranty applies to all products sold by authorized dealers in the United States and Canada and used within the United States and Canada. This warranty is limited to parts only and AXENT is not responsible for any installation labor charges, removal charges, installation, or other incidental or consequential cost. 2. AXENTs sole and maximum liability for breach of its warranties herein is limited to the obligation, at AXENTs sole discretion to repair, replace, or make appropriate adjustments to bring the product back to normal operating function. AXENT reserves the right to inspection of the product and verification of normal residential usage con-

ditions during the warranty period before warranty claims are handled. In no event shall AXENT or Seller be liable to Buyer for consequential, incidental, economic, or special damages stemming from any breach of express or implied warranty. 3. Purchaser shall comply with the following procedures in connection with the warranty claim:

- AXENT is notified in writing by Purchaser within thirty (30) days after discovery of defects;

- Purchaser obtains a Return Authorization from AXENT prior to returning any defective product to AXENT;

- The defective products are returned to AXENT, all shipping charges prepaid by Purchaser(provided however, that if upon examination by AXENT, it determines that the products are entitled to warranty, then AXENT shall be responsible for shipping charge to and from AXENT s facility).

- The defective products are received by AXENT for adjustment no later than fifteen (15) days following the last day of the war-

ranty period; and

- AXENTs examination of such goods shall disclose that such defects or failures have not been caused by misuse, abuse, neglect, improper installation or application, repair, alteration, damage by rain, fire or casualty or by accident or negligence in use, storage, transportation or handling. 4. This warranty does not apply to the following items:

- Damage or loss sustained in a fire, earthquake, storm or any natural disaster etc.

- Damage or loss resulting from any unreasonable use, misuse, abuse, negligence or improper care, improper cleaning or main-

taining of the product.

- Damage or loss as a resulting from the use of in-tank toilet cleaners.

- Damage or loss resulting from any sediments or foreign matter contained in the water system.

- Damage or loss from improper installation, harsh environment, improper removal and water pressure in excess of 80PSI.

- Damage or loss resulting from electrical surges, lightning strikes or other acts which are not considered normal or the fault of AXENT.

- Damage or loss resulting from normal wear and tear, such as gloss reduction or dulling, scratching or fading over time due to normal use, cleaning practices, water or atmospheric conditions including but not limited to: bleach, alkali, acid cleaners, dry powdered cleaners or any other abrasive cleaning agents or abrasive cleaning tools or aids.

- The use of any product in a manner outside of the product instructions / owners manuals.

- AXENT shall not be liable for any failure caused by chloramines in the public treated waters or cleaners containing chlorine

(calcium hypochlorite). Please note that use of high concentrate chlorine or chlorine related products can damage fittings. This damage can cause leakage resulting in property damage. 5. AXENTS OBLIGATION TO HONOR THESE WARRANTIES IS CONTINGENT UPON AXENTS RECEIPT OF PAYMENT IN FULL FOR THE GOODS ENTITLED TO THIS WARRANTY. AXENT DISCLAIMS ALL OTHER WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SELLER HAS NOT AUTHORIZED ANYONE TO MAKE ANY REPRESENTATION OR WARRANTY OTHER THAN AS PROVIDED ABOVE. THE FOREGOING STATES THE ENTIRE WARRANTY LIABILITY OF SELLER. To obtain warranty service, contact AXENTs service team through your dealer or plumbing contractor, or via the points of contact below:

Mailing Address: Attn. Customer Service Department 3 Musick, Irvine, CA 92618 E-mail: [email protected] Phone: 1-949-250-4576 Place serial number sticker here for reference:

AXENT Intelligence Inc. www.axentbath.us [email protected] 1-949-250-4576

. 0 1

5 2 0 0 5 7 0 2 0 0 0 4 2 2 N

P