FCC ID: 2AL4G-003 Remote Controller

REV. DESIGN DATE CONTENTS MARK QTY. 01 20231229 m m 0 1 2 MINT ONE USER MANUAL 142.5 mm TYPE TS026-3 1. 2. 142.5210mm 1mm 3. 4. 5. RoHS DESIGN CHECK PROCESS STANDARDIZE APPROVE 20231229 MATERIAL SIZE 100g A4 SCALE UNIT 12 mm TITLE PART NO. 224000168000 SHEET 1 OF 1 XIAMEN AXENT CORPORATION LIMITED MINT ONE TS- USER MANUAL THANK YOU Thank you for selecting an AXENT Switzerland product. To ensure proper installation, please review these instructions carefully before use. Carefully unpack and examine the intelligent toilet before installa-

tion. For any questions, contact us at 1-949-250-4576. Thank you again for choosing AXENT. BEFORE YOU BEGIN CAUTION!

Risk of personal injury or product damage Handle with care. Vitreous china can break or chip if handled carelessly. All installation procedures should comply with applicable local plumbing and building codes. I N STA L L AT I O N BY A P RO F ES S I O N A L , LICENSED PLUMBER OR CONTRACTOR IS HIGHLY RECOMMENDED. USER MANUAL MINT ONE Safety Introduction Multi-function dial Remote Control Maintenance Troubleshooting Technical data Guarantee 1 5 6 7 11 14 17 18 SAFETY SAFETY SYMBOLS The following symbols in the manual will highlight hazardous situations and their severities. DANGER!

High Risk, Lethal Hazards, Severe Injuries WARNING!

Medium Risk, Severe Injuries CAUTION!

Low Risk, Minor Injuries NOTE!

Damage to Property NORMAL USAGE The intelligent toilets spray arm attachment should only be used for the rear wash and front wash clean-

ing functions. The product may also be used as a normal toilet seat. This product is meant for indoors usage only. Any other usage will not be deemed as normal usage. AXENT undertakes no liability for abnormal usage. AXENT is not liable or responsible for damage to other electronics connected to the same power line while the intelligent toilet is in use. IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING SAVE THESE INSTRUCTIONS A copy of the instructions can also be downloaded from https://axentbath.us. When using electrical products, especially when children are present, basic safety precautions should always be taken, including the following:

DANGER!

To reduce the risk of electrocution Do not reach for any electrical components of the intelligent seat that have fallen into water. Unplug toilet immediately. Unplug product if not in use for extended periods of time. Do not use while wet after bathing. Do not place or store product where it can fall or be pulled into a tub or sink. Do not place or submerge the intelligent toilet or its components into water or other liquids. 1 SAFETY WARNING!

To reduce the risk of burns, electrocution, fire, or injury to persons. Children or disabled persons may require supervision during use. Use this product only for its intended use as described in this manual. Do not use attachments not authorized by the manufacturer. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair. Keep the cord away from heated surfaces. Do not block the air vents on this product. Do not place the toilet on or by objects such as long window curtains that could potentially obstruct the air vents during normal usage. Keep air vents free of lint, hair, and other debris. Never use while sleepy or drowsy. Never drop or insert any object into any openings or hoses. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. Connect this product to a properly grounded outlet only. See Section Grounding instructions on next page. Unplug this product before filling water. Fill (reservoir) with water only unless otherwise specified by manufacturer. Do not overfill. SAFETY INSTRUCTIONS Carefully read and observe the following safety instructions!

Information for the user Children or persons with limited physical/mental capabilities may require supervision or proper in-

structions/guidance prior to or during use. Ensure that children cannot play with intelligent toilet. Avoiding malfunctions and damage to the product as a result of improper use If intelligent toilet is moved from a cold location to a warm location, condensation may form. Leave the unit switched off for a few hours. Do not install the intelligent toilet in rooms where the temperature will be less than 4 C ( 39 F ). Do not place open flames, candles, cigarettes, or similar objects on or by the toilet. Do not reuse old hoses or water lines. Please use new water lines when installing. Do not install the intelligent toilet next to items that would potentially expose the toilet to a large amount of water. Do not climb on or stand on the product. 2 SAFETY Do not place any heavy objects on the lid. Do not open or close the lid or seat with force. Do not deliberately soil, spray or block the spray arm. Repairs should only be carried out by a person with the necessary expertise Do not carry out modifications, tamper with, install additional equipment, or attempt to repair the intel-

ligent toilet. Improperly performed repairs can lead to accidents, injuries, or damage to the product. Only use the device when it is fully functional Make sure the power cable is not damaged before use. Do not allow the power cable to be severely pinched, bent, or kinked. Keep the power cable away from hot surfaces and sharp edges. Do not handle the power cord or plug with wet hands. Do not use the product if it is not working properly. In case of malfunction, disconnect the power im-

mediately. Close the water cut-off valve to interrupt the water supply. Contact your installer. Information on the use of batteries Keep batteries out of the reach of small children. Batteries can be life-threatening if swallowed. If a battery has been swallowed, seek medical assistance immediately. Do not attempt to recharge non-chargeable batteries for use with unit. Always remove empty batteries from the remote control immediately. They may leak and cause damage. Do not insert new and old batteries together in the remote control. Clean the battery and contacts before inserting the battery. Make sure the batteries are oriented properly. Remove the batteries if the remote control will not be used for an extended period of time. Do not expose the batteries to hot surfaces or direct sunlight to reduce the risk of battery leakage. If battery acid has leaked, avoid contact with skin, eyes and mucous membranes. In case of contact with the acid, flush the affected areas with large amounts of clean water and seek medical assistance immediately. GROUNDING INSTRUCTIONS This product must be grounded when plugged in. The power cord on this product has a grounding plug and must be plugged into an outlet with a properly grounded grounding plug. DANGER!

Improper use of grounding plug can result in a risk of electric shock. For safety, the intelligent toilet should be plugged into a standard 3 prong GFCI outlet. 3 SAFETY Grounded outlet Grounding pin Grounded outlet box Wiring Diagram (NOT FOR INSPECTORS USE) If repair or replacement of the power cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. This product is not to be used with extension cords. This product is factory equipped with a specific electric cord and plug to permit proper connection. No adapters should be used with this product. Do not modify the power cord on the toilet. If the pow-

er cord will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel. Please unplug unit immediate and contact for service if cord becomes damaged. Do not use a bidet seat with a damaged cord. NOTE!

Actual installation may differ slightly from the diagram. FCC INSTRUCTIONS Please note that changes or modifications not expressly approved by the party responsible for compli-

ance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. RF exposure statement: This equipment complies with radio frequency exposure limits set forth by the FCC for an uncontrolled environment. This intelligent toilet [TS026-3 ] should be installed and operated with a minimum distance of 0.02 m between the device and the user or bystanders. This device must not be co-located or operating in conjunction with any other antenna or transmitter. 4 INTRODUCTION OVERVIEW

[TS026-3]

MAIN 5 DryFlushMulti-function DialLidRear coverManual Flush ButtonReset ButtonSeatFoot sencerNozzle MULTI-FUNCTION DIAL Function Button MAIN Operation Notes When you are not in the washing state, Press Manual Flush Button to start flushing. Please keep skin contact when you used When both the lid and the seat are opened for more than 4 seconds;

Kick the foot sensing area lightly on the lower right side of the toilet to start flushing. When the lid and the seat are both closed, Kick the foot sensing area lightly on the lower right side of the toilet to open the lid. When the lid is opened, and the seat is closed, Kick the foot sensing area lightly on the lower right side of the toilet to open the seat. After you are seated, Press Rear Wash to start. After you are seated, Press Front Wash to start. After you are seated, Press Dry to activate the dryer. After you are seated and finished washing, The dryer will be activated automatically. Press and hold Front Wash for more than 3 seconds to activate Stand-By mode.

- Press and hold Front Wash for more than 3 seconds to deactivate Stand-By mode. When the unit is not in use, Press the sensing area of seat for 5~9 times within 25 seconds to turn the function on or off

Please kick it again when hearing two shot beep from the main unit which means inef-

fective command. Press the button again to stop the Wash early. If not stopped manu-

ally the Wash will stop automatically after 3 minutes. It is recommended to wipe off most of the wate r w i t h a p a p e r towel before activating the dryer. In Stand-By mode, all functions of the toilet will deactivate except Multi-function dial until reactivated. Factory setting: ON Rear Wash Front Wash Dry Auto Dry Front Wash Please keep skin contact when you used Flush Flush by foot Seat and Lid Open by food Rear Wash Front Wash Dry Standby mode Seat and Lid Open by food Setting 6 REMOTE CONTROL Rear wash Front wash Stop Massage Dry Flush Water ow Water temp Position Air temp Light Seat temp When receiving remote control command, the main unit makes the following sound:

One short beep Two short beep One long beep Low battery will effect the use of remote control, please replace batteries in time. effective command ineffective command exceed the range of remote control Function Button Operation Notes REMOTE CONTROL Turn On Turn Off Pairing Opening and Closing the Seat and Lid

Stop Lid Seat Close Auto Open Install batteries to turn on remote control. Remove batteries to turn off remote control. Please do not insert new and old batteries together. Cut off the power of the intelligent toilet, wait for 30 seconds, and then reapply power. After three times short beeps, start pairing by quickly pressing Stop repeatedly within 5 seconds until hearing three times long beeps from the intelligent toilet, indi-

cating successful pairing. Pairing has originally been done in the factory. It is only necessary after the remote control has been replaced. Please make sure there is sufficient power supply for the remote control before pairing. When the unit is not in use, Press Lid to open the lid. When the unit is not in use, Press Seat to open the lid and seat. When the unit is not in use, Press Close to close the seat and lid. When Auto open is enabled and set to Lid, the lid will automatically open when some-

one approaches. When Auto open is enabled and set to Seat, the lid and seat will automatically open when someone approaches. Auto open only works when the lid is closed. The lid will only open auto-

matically after being closed for more than 10 seconds, provided that the previous user has left the unit for more than 10 seconds. Please find more infor-

mation about Auto Open setting on page 10 . 7 REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Flush Rear Wash Front Wash Flush Auto Flush Rear Wash Front Wash Oscillating and Pulsating Shower Massage Dry Dry Auto Dry When you are not in the washing state, Press Flush to start.

After being seated for more than 15 sec-

onds, the function will be started after a period of time defined by the Auto flush setting which defaults to 15 seconds. Please find more infor-

mation about Auto Flush setting on page 10 . After you are seated, Press Rear Wash to start. After you are seated, Press Front Wash to start. During Rear or Front wash, Press Massage to switch between:

- Oscillating

- Pulsating

- Oscillating and Pulsating

- OFF After you are seated, Press Dry to activate the dryer. After you are seated and finished washing, The dryer will be activated automatically. Press Stop to stop the function in pro-

gress. If not stopped manually the Wash will stop automatical-

ly after 3 minutes.

I t i s re c o m m e n d e d to wipe off most of the water with a paper towel before activating the dryer. If not stopped manually, the Dryer will stop auto-

matically after 5 minutes. Stop Stop

Press Stop for more than 3 seconds to exit the Settings mode Smart Night Light Light Press Light to turn on or turn off the smart night light. Factory setting: ON When the setting is on, smart night light turns ON or OFF automatically according to ambient light levels. 8 REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Water flow Water Flow During Rear or Front wash, Press Water Volume to adjust the water volume.

- Press Increase to increase the water volume. Increase Reduce

- Press Reduce to reduce the water volume. Position Spray Arm Position Increase Reduce During Rear or Front wash, Press Position to adjust the position of the spray arm.

- Press Increase to move the Spray Arm forward.

- Press Reduce to move the Spray Arm backward. Level Indicator indicates the selected level. Seat Temp Seat Temp Increase Reduce Press Seat Temp to activate tempera-

ture adjustment.

- Press Increase to increase the tem-

perature.

- Press Reduce to reduce the temper-

ature. Water Temp Water Temp Increase Reduce During Rear or Front wash, Press Temp to activate temperature adjustment.

- Press Increase to increase the tem-

perature.

- Press Reduce to reduce the temper-

ature. Air Temp Air Temp During Dry, Press Temp to activate temperature adjustment.

- Press Increase to increase the tem-

perature. Increase Reduce

- Press Reduce to reduce the tem-

perature. Level Indicator indicates the selected level. All indicators go off means the heating function is turned off. After the completion of temperature adjustment, the system automatically records and displays the temperature information when initiating the next Washing or Drying. 9 Auto Flush after closing the seat and lid Setting Auto Open Setting REMOTE CONTROL Function Button Operation Notes REMOTE CONTROL Signal Tone Setting Stop Water Temp Press Stop at the same time Water Temp for more than 3 seconds to turn the function on or off. Factory setting: ON When the setting is OFF, the system shut down all prompt sounds. Eco Setting Stop Seat Temp Press Stop at the same time Seat Temp for more than 3 seconds to turn the function on or off.

- ON

- OFF Night light flashes twice;

One short beep. Factory setting: OFF When the ECO setting is on, the seat will be intelli-

gently heated according to the users usage habits. Deodorize setting Stop Water Flow Press Stop at the same time Water Flow for more than 3 seconds to turn the function on or off. Factory setting: ON When the setting is on, the deodorizer function is activated when a user is seated. Close Flush Press Close at the same time Flush for more than 3 seconds to turn the func-

tion on or off. Factory setting: OFF Stop Lid Seat Position Close Press Stop at the same time Position for more than 3 sec-

onds to enter into the Setting. Press Lid to activate the lid mode, indicated by one remaining indi-

cator. Press Sead to ac-

tivate the Seat mode, indicated by two re-

maining indicators. Press Close to ac-

tivate the close mode, i n d i c ate d by t h re e remaining indicators. Auto Flush after leaving Setting Stop Flush Increase Reduce Press Stop at the same time Flush for about 3 seconds to enter into the Setting.

- Press Increase to increase the time.

- Press Reduce to reduce the time. Sencing distance adjustment Water Temp Seat Temp Press Water Temp at the same time Seat Temp for more than 3 seconds to switch between:

- Level 1

- Level 2

- Level 3 10 Factory setting: Lid Level Indicator indicates the selected level. Lid mod: Only lid is opened. Seat mode: Lid and Seat are opened. Close mode: Close the Auto Open function. Factory setting: 15 seconds Three options in total:

- 5 seconds

- 10 seconds

- 15 seconds Factory setting: Level 2 Level Indicator indi-

cates the selected level. This function allows the user to adjust the detection distance for Auto Open be-

tween the toilet and them-

selves. MAINTENANCE SPRAY ARM CLEANING When the unit is not in use, Rear Wash Press Rear Wash on the multifunction dial to extend the spray arm for cleaning. Clean the spray arm with a fabric or a soft bristle brush. Press Stop to retract the spray arm. Stop If no other functions are used, the spray arm will automatically retract after 3 minutes. FILTER CLEANING 2 Coin or Similar The filter screen will need to be cleaned frequently. If the unit does not fill up properly, starts to lose pressure, or has no function normally, please clean the filter first. DO NOT use the product without the filter. Otherwise the product may not be warranty. The water inlet valve must be shut off during the entire filter cleaning process. The filter may be reinserted in reverse after cleaning. Inlet Valve Filter 11 MAINTENANCE SUITABLE CLEANING DETERGENTS

- Mild bathroom or all-purpose cleaner

- Mild detergents

- Normal toilet brushes

- Soft sponges

- Microfiber cloth CLEANING INSTRUCTIONS SEAT, LID AND BACK COVER Use a mild soap solution to clean the seat. Please take care that the seat and hinges are not left damp. Dry off any residual water or cleaning agent with a soft cloth. Ensure that the seat and seat hinges do not come in contact with abrasive, corrosive, or chlorine-based cleaners, as these may cause damage or lead to flash rust. When cleaning the bowl, make sure that the seat and cover are kept in an upright posi-

tion until all cleaning agent has been flushed away. DISCONNECT THE MAIN PLUG BEFORE YOU START WITH CLEANING THE PRODUCT. Do NOT use any scouring equipment or tools (ex: scouring pad) or any aggressive cleaning agents for cleaning. CLEANING CERAMIC APPLIANCES Do not use harsh or abrasive cleaning substances such as abrasive cleansers, scouring powder or drain cleaner on your ceramic surfaces. Also avoid using steam cleaners and hard, abrasive sponges. Please do not pour or dispose of hair coloring products into the toilet as this can reduce the effectiveness of the AXENT Easy Clean coating. By following these maintenance guidelines, AXENT Easy Clean should remain effective for many years. AXENT highly recommends the use of acidic cleaners with a pH value between 1 and 4. Cleaners with a pH value in the neutral range (5 to 8) are not always suitable. We strongly advise against using either weak or strong alkaline cleaners, i.e. substances with pH values from 9 to 12. WINTERIZATION Please ensure water temperatures will not drop below 4 C (39 F). Frost or frozen water will damage the system and may lead to leakage. If the water or ambient temperature drops below 4 C (39 F), please discontinue use of product.

- Disconnect the electrical power.

- Shut off the water inlet valve.

- Disconnect the water inlet hose from the filter to drain out the water inside of the line.

- Press the Manual Flush Button. FAILURE TO DRAIN SYSTEM MAY RESULT IN DAMAGE TO SYSTEM AND LEAKAGE OR FLOODING. If the intelligent toilet is moved from a cold location to a warm location, condensation may form. Leave the unit switched off for a few hours before use. 12 MAINTENANCE DURING VACATION If this product will not be in use for an extended period of time, please perform the following in this order.

- Disconnect the electrical power.

- Shut off the water inlet valve.

- Disconnect the water inlet hose from the filter to drain out the water inside of the line.

- Close the lid, then use a flat-head screwdriver to pry open the intelligent cover from the gap in the back cover and then lift it out upwards, as shown in picture 1.

- Use a screwdriver to turn the switch clockwise, which is located on the underside of the intelligent cover shown in picture 2, in order to drain the water. Once all the water has completely drained out, remember to turn the switch back as shown in picture 3 to prevent water leakage during use. Screwdriver

(Pic1)

(Pic2)

(Pic3) The horizontal oscillation of the intelligent cover facilitates more efficient drainage of excess water. REPLACE BATTERIES Remove old batteries Insert new batteries

A A A A A A

A A A A A A

13

A A A A A A

TROUBLESHOOTING IN CASE OF THE FOLLOWING PHENOMENA, PLEASE CUT OFF THE POWER AND SHUT OFF THE WATER INLET VALVE IMMEDIATELY.

- Water leakage.

- Hearing continuous beep . PREPARE FOR CHECK Check the Power Supply

- If the power supply could work normally Check Water Supply

- If the water supply could work normally

- If the water inlet valve is shut off FREQUENTLY ASKED QUESTIONS In case of minor malfunctions, please refer to the following solutions. If the below solutions do not resolve the issue, please contact customer support for further examination and repair. Malfunction Cause Solution MAIN No function Product in Stand-by mode Press and hold Front Wash on the multifunction dial for more than 3 seconds to deactivate Stand-By mode. REMOTE CONTROL Does not work Battery is low Replace batteries. Wrong oriented Reinstall batteries with correct oriented. Existing distractions Remove distractions. Out of range Please use the remote control within the inductive dis-

tance. Can only be activated dur-

ing the wash cycle Restart massage during Front or Rear wash. Auto open off Lid is opening Last user has left the unit for less than 10 seconds. Auto open set as Lid Set auto open as Lid or Seat. Auto open only works when the lid is closed. Please try again after staying away for at least 10 sec-

onds. Set Auto Open as Seat. Remote control works but does not control toilet MASSAGE Does not work AUTO OPEN Auto Open does not work S e a t d o e s n o t open automatically 14 TROUBLESHOOTING DRY D r yer does not work Low air tempera-

ture No air tempera-

ture Seat does not sense per-

son Air temperature set too low Air temperature set off Reconfirm position on seat. Increase air temperature. Increase air temperature. REAR WASH AND FRONT WASH Spray arm extend too slowly Low water pres-

sure It will take 5 seconds to move out. Filter is blocked Connection loose Low water tem-

perature Water stop sud-

d e n l y a n d t h e spray arm retract back Water temperature set too low Leaving the seat During Rear or Front wash If not stopped manually the Wash will stop auto-

matically after 3 minutes. Heating error Please be patient. Clean filter. Check connection between hose and main, and tighten it. Increase water temperature. Seated and restart the washing. It is nomal. Perform a reset by pressing the button located in the top left corner behind the intelligent cover. S p ra y a r m ex-

t e n d w i t h o u t w a t e r spraying out NIGHT LIGHT Does not work Night light always on AUTO FLUSH Does not work Seat does not sense per-

son Reconfirm position on seat. Night light in OFF mode Night light in ON mode and the ambient light is too dim Light sensor blocked by object Switch night light setting to ON mode. Switch night light OFF mode. Remove distractions. Being seated for less than 15 seconds the function will be activated after being seated for more than 15 seconds 15 TROUBLESHOOTING SEAT HEATER Low seat temper-

ature Low seat temper-

ature when initially seated Seat temperature reduce automat-

ically High seat tem-

perature Seat heater does not work DEODORIZE Deodorizer does not work Seat temperature set too low ECO mode is on Increase seat temperature. Please turn off ECO. Seat Low TEMP Protec-

tion will be activated auto-

matically after Seated for a while Seat temperature set too high Seat temperature set too low Heating error It is normal. Please adjust Seat temperature or reseated to disable Seat Low TEMP Protection. And Seat Low TEMP Protection will be activated again after 5 minutes. Reduce seat temperature. Increase seat temperature. Disconnect the main plug and contact customer service. Deodorize off Seat does not sense per-

son During Rear or Front wash It is normal. Deodorize is disable During Rear or Front Please active Deodorize function. Reconfirm position on seat. wash. This is normal. Restart Self-cleaning again. Disconnect the main plug and contact customer service. Deodorizer still runs after leaving seat The deodorizer continues to run for a while after leav-

ing the seat to increase effectiveness SELF-CLEANING Spray arm retracts a u t o m a t i c a l l y during Desc ale process Wand will automatically retract after 3 minutes of inactivity WARNING Continuous beep Water temperature exceeds normal range 16 TECHNICAL DATA Nominal voltage Power consumption Protection degree Water Volume Cable length 120 V~, 60 Hz 930W IPX4 1.0 gpf/3.8 lpf 1.0 m ( 393/8 in) Minimum and Maximum pressure

(bidet portion only) 0.1 - 0.75 MPa ( 15- 108 psi ) Operating pressure (toilet) Refer to cistern specifications Ambient temperature range 4 - 40 C ( +39 to +104 F ) Water temperature range 4 - 35 C ( +39 to +95 F ) Product dimension ( L B H ) 683 385 492 mm ( 289/10 151/5 191/3 ) Maximum load (Seat and lid) 150kg ( 330lbs ) Max. flow rate rear wash Max. flow rate front wash Spray arm position Water temperature Air dryer temperature Seat temperature 550m L/min 550m L/min Ambient Temp, 35 - 39 C Ambient Temp, 38 - 46 C Ambient Temp, 32 - 37 C 5 levels 4 levels 4 levels 4 levels TECHNICAL SUPPORT For any questions or any assistance with this product, please contact your dealer or call us at 1-949-250-4576 [email protected] www.axentbath.us LEGAL DIRECTIONS This manual contains important information on the intended use, correct operation and proper maintenance of the equipment. Knowledge of and compliance with the instructions of this manual are provided for both the safe use of the equipment and for the safety of its operation and maintenance. In this manual, not all kinds of applications and improper manipulations are considered. In addition, attention is drawn to the following: The content of these instructions is neither part of any previous or existing agreement, commitment or legal relationship, nor does it change from an existing agreement, commitment or legal relationship. Any commit-

ment by AXENT results from the respective warranty. These include the complete and authoritative warranty obligation AXENT. The statements in this manual do not constitute an extension or a restriction of the claims under the warranty provisions. This manual is protected by copyright. Copies and / or translations into other languages may be made only with prior written approval of AXENT. 17 GUARANTEE AXENT LIMITED WARRANTY A three-year limited warranty applies to all AXENT products purchased on or after May 1, 2019. All prod-

ucts purchased on or before April 30, 2019 OR purchased for use in a commercial or hospitality setting on any date are backed by AXENTs one-year limited warranty. All spare parts purchased for use with Axent products are covered by a six (6) month limited warranty unless otherwise stated on the product. 1. AXENT warrants that its products are free from defects caused by defective material and faulty workmanship for a period of three-year from the date of purchase by the original purchaser. The limited warranty is to the original purchaser only. The limited warranty is not transferable to any third party. Proof of purchase showing both original ownership and purchase date is required for any warranty claim. The limited warranty applies to all products sold by authorized dealers in the United States and Canada and used within the United States and Canada. This warranty is limited to parts only and AXENT is not responsible for any installation labor charges, removal charges, installation, or other incidental or consequential cost. 2. AXENTs sole and maximum liability for breach of its warranties herein is limited to the obligation, at AXENTs sole discretion to repair, replace, or make appropriate adjustments to bring the product back to normal operating function. AXENT reserves the right to inspection of the product and verification of normal residential usage con-

ditions during the warranty period before warranty claims are handled. In no event shall AXENT or Seller be liable to Buyer for consequential, incidental, economic, or special damages stemming from any breach of express or implied warranty. 3. Purchaser shall comply with the following procedures in connection with the warranty claim:

- AXENT is notified in writing by Purchaser within thirty (30) days after discovery of defects;

- Purchaser obtains a Return Authorization from AXENT prior to returning any defective product to AXENT;

- The defective products are returned to AXENT, all shipping charges prepaid by Purchaser(provided however, that if upon examination by AXENT, it determines that the products are entitled to warranty, then AXENT shall be responsible for shipping charge to and from AXENT s facility).

- The defective products are received by AXENT for adjustment no later than fifteen (15) days following the last day of the war-

ranty period; and

- AXENTs examination of such goods shall disclose that such defects or failures have not been caused by misuse, abuse, neglect, improper installation or application, repair, alteration, damage by rain, fire or casualty or by accident or negligence in use, storage, transportation or handling. 4. This warranty does not apply to the following items:

- Damage or loss sustained in a fire, earthquake, storm or any natural disaster etc.

- Damage or loss resulting from any unreasonable use, misuse, abuse, negligence or improper care, improper cleaning or main-

taining of the product.

- Damage or loss as a resulting from the use of in-tank toilet cleaners.

- Damage or loss resulting from any sediments or foreign matter contained in the water system.

- Damage or loss from improper installation, harsh environment, improper removal and water pressure in excess of 80PSI.

- Damage or loss resulting from electrical surges, lightning strikes or other acts which are not considered normal or the fault of AXENT.

- Damage or loss resulting from normal wear and tear, such as gloss reduction or dulling, scratching or fading over time due to normal use, cleaning practices, water or atmospheric conditions including but not limited to: bleach, alkali, acid cleaners, dry powdered cleaners or any other abrasive cleaning agents or abrasive cleaning tools or aids.

- The use of any product in a manner outside of the product instructions / owners manuals.

- AXENT shall not be liable for any failure caused by chloramines in the public treated waters or cleaners containing chlorine

(calcium hypochlorite). Please note that use of high concentrate chlorine or chlorine related products can damage fittings. This damage can cause leakage resulting in property damage. 5. AXENTS OBLIGATION TO HONOR THESE WARRANTIES IS CONTINGENT UPON AXENTS RECEIPT OF PAYMENT IN FULL FOR THE GOODS ENTITLED TO THIS WARRANTY. AXENT DISCLAIMS ALL OTHER WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SELLER HAS NOT AUTHORIZED ANYONE TO MAKE ANY REPRESENTATION OR WARRANTY OTHER THAN AS PROVIDED ABOVE. THE FOREGOING STATES THE ENTIRE WARRANTY LIABILITY OF SELLER. To obtain warranty service, contact AXENTs service team through your dealer or plumbing contractor, or via the points of contact below:

Mailing Address: Attn. Customer Service Department 3 Musick, Irvine, CA 92618 E-mail: [email protected] Phone: 1-949-250-4576 Place serial number sticker here for reference:

AXENT Intelligence Inc. www.axentbath.us [email protected] 1-949-250-4576

. 0 1

3 2 0 0 0 8 6 1 0 0 0 4 2 2 N

P

REV. DESIGN DATE CONTENTS MARK QTY. 01 20230920 m m 5 2 Axent Intelligence Inc. AA029-0-WT FCC ID: 2AL4G-003 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 100 mm TYPE 1 1. 85PE 2. 3. 100*30mm 0.5mm 4. 5. REACH 6. DESIGN CHECK PROCESS STANDARDIZE APPROVE 20230920 MATERIAL SIZE A4 SCALE UNIT OF 1:1 mm 1 SHEET 1 TITLE PART NO. FCC ID 225000311900 XIAMEN AXENT CORPORATION LIMITED

AXENT Intelligence Inc. Date: 20231016 Authority to Act as Agent TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint MS.Yanli Fan of TUV Rheinland (shanghai) Co., Ltd to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with AXENT Intelligence Inc. / 3 Musick Irvine, CA 92618, Irvine California United States For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Date:

20231016 Agreement is valid for 12 months from the above date. By:

(Signature)

(Title) On behalf of:

AXENT Intelligence Inc.

(Company Name) Jasmine Liu

(Print name) 949-900-4342

(Telephone) Page 1 of 1 COO

AXENT Intelligence Inc. Applicant as U.S. Agent Letter of Attestation Date: 10-16-2023 To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Attestation Statement Part 2.911(d)(7) filing FCC ID: 2AL4G-003 AXENT Intelligence Inc. (the applicant) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. Designated U.S. Agent from Applicant Company Company Name: AXENT Intelligence Inc. Contact Person: Jasmine Liu Address: 3 Musick Irvine, CA 92618, Irvine California United States Tel.: 949-900-4342 Email: [email protected] FCC FRN: 0026517722 Sincerely yours, Signature Printed Name: Jasmine Liu Title:

Email: [email protected] COO

AXENT Intelligence Inc. Date: _20231016_____ Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Confidentiality Request for FCC ID: 2AL4G-003 Pursuant to FCC 47 CRF 0.457(d), the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent n/a Permanent Permanent Permanent Permanent Permanent Permanent Permanent Exhibit Block Diagrams External Photo Internal Photos ***

Operation Description/Theory of Operation Schematics Test Setup***

Tune-Up Procedure Users Manual***

Part List/ Antenna Construction AXENT Intelligence Inc.has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public.

(*** Exceptional case for Permanent Confidentiality for these Exhibits by PAG only) Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By:

_______________________________________________ __ Jasmine Liu __________________

(Signature/Title)

(Print name) Tel: 949-900-4342 Email: [email protected] MS-0044715 Page 1 of 1 Revision 1

AXENT Intelligence Inc. Attestation Statements Not Covered Entity Applicant To: Federal Communications Commission Date: 10-16-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(ii) filing FCC ID: 2AL4G-003

[AXENT Intelligence Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely yours, Applicant Signature Printed Name: Jasmine Liu Title:

Address: 3 Musick Irvine, CA 92618, Irvine California United States Tel.: 949-900-4342 Email: [email protected] COO

AXENT Intelligence Inc. Attestation Statements Not Covered Equipment To: Federal Communications Commission Date: 10-16-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) filing FCC ID: 2AL4G-003

[AXENT Intelligence Inc.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Jasmine Liu Title:

Address: 3 Musick Irvine, CA 92618, Irvine California United States Tel.: 949-900-4342 Email: [email protected] COO