FCC ID: 2AR8J-EMP1000 Wireless push button for electronic bus stop display

iBus EPM-1000 wireless push button User Manual 1.1 1.2 Contents 1 EPM-1000 User Manual ...................................................................................................................... 1 EPM-1000 usage ..................................................................................................................................... 1 EMP-1000 technical functionality ............................................................................................................. 1 2 FCC and IC statements ....................................................................................................................... 1 FCC Part 15 ............................................................................................................................................. 1 Industry Canada Notifications .................................................................................................................. 2 Information about FCC ID and IC ID ........................................................................................................ 2 3 Technical specification for the EPM-1000 ........................................................................................... 3 2.1 2.2 2.3 1 EPM-1000 User Manual 1.1 EPM-1000 usage The EPM-1000 wireless push button is used to trigger the Text-To-Speech (TTS) in the dynamic display IBD3750. IBD3750 is a 5-row LCD display for bus stops that shows bus departures and passenger information. 1.2 EMP-1000 technical functionality The EMP-1000 wireless push button contains an ISM UHF radio operating in the 915 MHz band. The ISM UHF radio is powered by a Lithium Thionyl Chloride battery. When the button in the EPM-1000 is pushed, the EPM-1000 will transmit a radio signal that is detected by the display IBD3750. On receiving the radio signal from the EMP-1000, the display IBD3750 will start the TTS functionality, and will make an audio presentation of the information shown on the display rows. 2 FCC and IC statements 2.1 FCC Part 15 This device complies with FCC Rules Part 15 operation is subject to the following two conditions:

1. This device may not cause harmful interference. Axentia Technologies AB Universitetsvgen 14 SE-583 30 Linkping, Sweden Editor: pk E-mail: info@axentia.se Phone: +46 13 32 85 30 1-B iBus EPM-1000 wireless push button User Manual v2.0.docx Date: 2018-10-23 Page 1 (4) Axentia Technologies 1-B iBus EPM-1000 wireless push button User Manual v2.0.docx 2. This device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications to this device, not expressly approved by Axentia Technologies AB could void the users authority to operate the equipment. FCC RF Exposure Requirements: This product complies with the FCC RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. This device is only authorized for use in a mobile application, at least 20 cm of separation distance between the radiating antenna and the user's body must be maintained at all times. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the users body or set the device to a lower output power if such a function is available. Separate approval is required for all other operating configurations, including portable configurations with respect to 47 CFR Part 2.1093 and different antenna configurations. 2.2 Industry Canada Notifications This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage ;

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. ISED RF Exposure Requirements: This product complies with the FCC RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. This device is only authorized for use in a mobile application, at least 20 cm of separation distance between the radiating antenna and the user's body must be maintained at all times. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the users body or set the device to a lower output power if such a function is available. Separate approval is required for all other operating configurations, including portable configurations with respect to 47 CFR Part 2.1093 and different antenna configurations 2.3 Information about FCC ID and IC ID FCC ID: 2AR8J-EPM1000 IC: 24627-EPM1000 Page 2 (4) Axentia Technologies 1-B iBus EPM-1000 wireless push button User Manual v2.0.docx 3 Technical specification for the EPM-1000 Manufacturer:

Axentia Technologies AB Universitetsvgen 14 583 30 Linkping, Sweden www.axentia.se

+46 13 32 85 31 Product name:

iBus wireless push button (EPM-1000) Product type:

Wireless push button for TTS UHF ISM Radio:

The UHF ISM radio is used for wireless communication with a wireless push button (info button). The wireless push button is optionally used for triggering of the Text-To-Speech functionality. Modulation: FSK (Frequency-shift keying), f = 150 kHz, data rate 25 kbit/s Frequency Range/Band: 915 ism band. ITU Region 2 frequency range 902 928 MHz. Nominal center frequency fc = 915 MHz

= = 915 150 The center frequency fc is static. It can be changed, but only by uploading new software (in production / production testing, before assembly). Transmission power: Below 10 mW Antenna gain: EIRP approx. -2 dBm Antenna type: Single F-antenna, gain approx 0 dBi. Non-detachable antenna (integrated on pcb). Operation mode: Non-adaptive mode only Tranceiver circuit : Semtech SX1211 Power: Primary Lithium Thionyl Chloride, 3.6 V, 8500 mAh (c.f. MINAMOTO Push button battery spec.pdf) Page 3 (4) Axentia Technologies 1-B iBus EPM-1000 wireless push button User Manual v2.0.docx Physical dimensions of the EPM-1000 wireless info-button:

Height:

Width:

Depth:

Weight:

135 mm 80 mm 50.3 mm 370 g Info button lid (inside):

- Pcb with radio + antenna molded (IP65)

- Mold material: Polyurethane/Epoxy Page 4 (4)

EPM-1000 (Info Button), pcb sides Top side. Left side Bottom side. Right side EPM-1000 (Info Button), pcb front and rear EPM-1000 pcb (molded into the top lid), front. EPM-1000 pcb (molded into the top lid), rear. EPM-1000 Info Button TransLink EPM-1000 (Info Button), top/bottom lids removed Screws Bottom lid Push button for TTS activation Top lid, ISM UHF radio molded into the top lid. Cable connecting the display module to the batteries and to the loudspeaker Casing (extruded aluminum) Battery (Lithium Thionyl Chloride) EPM-1000 (Info Button), top/bottom lids removed Top lid inside, ISM UHF radio molded into the top lid. Casing inside.

EPM-1000 (Info Button) EPM-1000 (Info Button) front and rear EPM-1000 (Info Button) top and bottom EPM-1000 (Info Button) left side and right side

Sample and size FCC / IC label (EPM1000) 36 mm 15 mm 24627 Font height 1,5 mm 24627

Product model #: EPM1000 FCC ID: 2AR8J-EPM1000 IC ID: IC: 25627-EPM1000 Manufacturer:

Axentia Technologies AB, Sweden FCC/IC Label Location

13-Axentia EPM-1000 FCC REQUEST FOR CONFIDENTIALITY.docx 1(2) Date: 3 July 2019 To: Federal Communications Commission Equipment Authorization Branch Laboratory Division Office of Engineering and Technology 7435 Oakland Mills Road Colombia, Maryland 21046 Subject: Request for Confidentiality Applicant: Axentia Technologies AB TYPE OF EQUIPMENT: Wireless TTS push button EPM-1000 FCC ID:

IC ID:

2AR8J-EPM1000 24627-EPM1000 Dear Sir or Madam:

Some of the material included in this application contains trade secrets and proprietary information not customarily released to the public. Because public disclosure of the material might be harmful to the applicant and provide unjustified benefits to its competitors, it is requested that the following be withheld from public disclosure:

Exhibit Type Schematic Diagrams File Name 03 - 2AR8J-EPM1000_Schematic for Info Button Block Diagram 02 - 2AR8J-EPM1000_ Info Button Block Diagram Parts List 04 - 2AR8J-EPM1000_Info Button V2-915MHz-BOM Operational Description 05 - 2AR8J-EPM1000_wireless TTS push button functional description v1.0 Trade secrets and proprietary information can be held confidential. Therefore, we wish to invoke the act under the provisions of 47CFR, Sections 0.457(d) and 0.459. Please contact the undersigned if you have any questions or need any further information. Regards, Per Klr E-mail: pk@axentia.se, Telephone: +46 730 74 62 29 Axentia Technologies AB www.axentia.se Axentia Technologies AB Universitetsvgen 14 SE-583 30 Linkping Sweden Ph: +46 13 328530 Fax: +46 13 328531 info@axentia.se www.axentia.se VAT reg.no SE556660949001

11-Axentia QAI POA.docx 1(1) Linkping 3 July 2019 Axentia Technologies AB Universitetsvgen 14 SE-583 30 Linkping Sweden RE: Authorization for acting on the behalf of Axentia (POA) Product Model Number: EPM-1000 FCC ID: 2AR8J-EPM1000 IC ID: 24627-EPM1000 To whom it may concern, We authorize Rick Hiebert of QAI Laboratory Ltd, 3980 North Fraser Way, Burnaby, BC V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:

Testing Approval applications and procedures We declare that QAI Laboratory Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratory Ltd. on our behalf shall have the same effect as acts of our own. By:

Per Klr Title: Product Manager Email: pk@axentia.se Telephone: +46 730 74 62 29 On behalf of: Axentia Technologies AB ______________________________________________________________________________________________________________________________________ Axentia Technologies AB Universitetsvagen 14 SE-583 30 Linkping, Sweden Ph: +46 13 328530 Fax: +46 13 328531 info@axentia.se www.axentia.se VAT reg.no SE556660949001