FCC ID: I38KSFT210ZB Zigbee Button

Thank you for using Kyla product! Please keep this

Easy Start Guide for future use. For support or help, visit

kylas.aztech.com

DISCLAIMER

Aztech Technologies Pte Ltd, its holding company and its

associated companies (hereinafter referred to collectively

as “Aztech”) does not guarantee that adequate warning or

protection will be given, and disclaims all warranties and

representations, whether expressed, implied or otherwise

statutory, concerning the product,

including without

limitation any warranty of merchantability or fitness for a

particular purpose. Aztech shall not be liable in any event for

any consequential, indirect, incidental, special, exemplary,

punitive or enhanced damages resulting from the use,

maintenance or operation of the product.

The manufacturer makes no warranty or representation that

the product constitutes a fire alarm system or is compliant

with any requirements prescribed by any applicable state

or laws, codes, regulations and/or other specifications that

may be set out by relevant authorities having jurisdiction

(collectively referred to as “regulations”). You shall be solely

responsible for compliance with all regulations.

To the maximum extent permitted by applicable law, you

agree to hold harmless and indemnify, including legal fees,

the manufacturer and their personnel against any third

party claims or fines by authorities that arise or are alleged

to have arisen as a result of negligent or intentional act or

omission by you or breach by you of any the terms herein

or any violation of any regulations.

PACKAGE CONTENTS

• Smart Button x 2

• CR2032 Battery x2

• Easy Start Guide

• Warranty Card

• Double-sided tape x2

PRODUCT DESCRIPTION

The Smart Button is a multipurpose button that

can be programmed to quickly perform the

following features with one, two or three presses:

• Launch automated scenes

• Control other smart devices

• Trigger emergency alarm

The Smart Button also adopts the Zigbee wireless

technology for a long-lasting battery life. Paste it

on the wall or place it on the table, this chic and

portable device blends in anywhere.

PRODUCT OVERVIEW

OPERATION GUIDE

Smart Button

Step 1:

Download Kyla App from Google Play/App Store.

Requirement:

•

iOS 12.0 or later

• Android 5.0 or later

Kyla App

LED Status Indicator Light x3

Smart Button Action

Result

Press once.

Press twice.

User-defined via app.

LEDs blink once.

User-defined via app.

LEDs blink twice.

Press and hold for 1.5 to

5 seconds.

User-defined via app.

LEDs rotate for two cycles.

Press and hold for 5

seconds or more.

Release button press.

All 3 LEDs will turn on.

Enter Pairing Mode.

1 LED blinks rapidly for 30

seconds.

1

2

3

4

© 2019 Aztech Technologies Pte Ltd. All rights reserved.

Step 2:

Rotate the back cover counterclockwise to open.

Step 3:

Insert the battery correctly based on the

positive and negative terminals of the battery.

Step 5:

Login to Kyla App, then add “Smart Button” to

the device list.

TECHNICAL SPECIFICATIONS

Back Cover

Reset

Button

Step 6:

To enter Pairing Mode, press and hold the button

for 5 seconds or more then release button press.

This triggers 1 LED to blink rapidly for 30 seconds.

Follow the remaining setup guide on the app.

SMART BUTTON

EASY START GUIDE

Power Supply

DC 3V

Battery Type

CR2032

Operating Temperature

0–40°C

Operating Humidity

30–80% RH (Non-Condensing)

Connectivity

Zigbee

Indicator Lights(s)

Green LED x 3

Communication Distance

10m to Hub (Indoor)

Casing Material

PC and ABS

Certificate(s)

FCC, CE, IMDA

Unlock

Lock

Battery

Step 4:

Close the back cover and rotate clockwise to lock.

PERFORMING A RESET

Press the Reset button on the back of the device.

5

6

7

8

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired

operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a

minimum separation distance of 5mm must be maintained between the user’s body and the handset,

including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not

contain any metallic components. Body-worn accessories that do not meet these requirements may not

comply with RF exposure requirements and should be avoided. Use only the supplied or an approved

antenna.

par hey AZITECH TEC NOLOG ES PTE LTD Company: AZTECH TECHNOLOGIES PTE LTD Address: 31 Ubi Road 1, #01-05, Singapore 408694 Product Name: Zigbee Button Model Number(s): KSFT-210-ZB Product Description: Zigbee Button We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all infarmation related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-2-26 Name: Terence Kwong ait: s Company: AZTECH TECHNOLOGIES PTE LTD

ECH TECHNOLOGIES PTE LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-2-26 Subject; Request for Confidentiality FCC ID: I388KSEN210ZB To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram

>] Block Diagram x] Parts List XX] Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos AZTECH TECHNOLOGIES PTE LTD Test Setup Photos X] Internal Photos SAU FS -vam Vi telale rel

[_] For 45 days, pursuant to Public Notice DA 04-1705. OR

{] For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature Name: Terence Kwong