FCC ID: I38KSEN210ZB Zigbee Motion Sensor

DETECTION RANGE BATTERY PLACEMENT 1. Remove back cover. PACKAGE CONTENTS Smart Motion Sensor Wall Bracket Ball Joint Plastic Anchor Screw Easy Start Guide Warranty Card PRODUCT DESCRIPTION X 1 X 1 X 1 X 2 X 2 X 1 X 1 Thank you for using Kyla product! Please keep this Easy Start Guide for future use. For support or help, visit kylaconnect.com DISCLAIMER Aztech Technologies Pte Ltd, its holding company and its associated companies (hereinafter referred to collectively as Aztech) does not guarantee that adequate warning or protection will be given, and disclaims all warranties and representations, whether expressed, implied or otherwise statutory, concerning the product, including without limitation any warranty of merchantability or fitness for a particular purpose. Aztech shall not be liable in any event for any consequential, indirect, incidental, special, exemplary, punitive or enhanced damages resulting from the use, maintenance or operation of the product. The manufacturer makes no warranty or representation that the product constitutes a fire alarm system or is compliant with any requirements prescribed by any applicable state or laws, codes, regulations and/or other specifications that may be set out by relevant authorities having jurisdiction

(collectively referred to as regulations). You shall be solely responsible for compliance with all regulations. To the maximum extent permitted by applicable law, you agree to hold harmless and indemnify, including legal fees, the manufacturer and their personnel against any third party claims or fines by authorities that arise or are alleged to have arisen as a result of negligent or intentional act or omission by you or breach by you of any the terms herein or any violation of any regulations. The Smart Motion Sensor can detect heat and movement in the surrounding areas based on the human bodys infrared spectrum detection technology, creating a protective grid. If a moving object blocks too many grid zones and the infrared energy levels change rapidly, the sensor is triggered. Pair with the Smart Hub and Kyla App for an integrated home monitoring system. LED Indicator Detection Window NOTE: Maximum up to 8 metres. INSTALLATION TIPS 1. Choose the correct installation direction. The infrared sensor has the highest detection sensitivity when perpendicular to the walking direction. To achieve the best results, please choose the most appropriate position and direction according to the actual situation and reference range diagram for installation. 2. Do not point towards heat or cold sources The infrared detection is closely related to temperature. An unstable ambient temperature may trigger a false alarm. Therefore, the infrared devices should be installed away from heaters, air conditioners, refrigerators or any possible heat and cold sources. 3. Do not point towards moving objects. Moving objects may trigger a false. 4. Recommended installation height: 2m above ground. Battery Cover Bracket Slot Reset Button 2. Place battery. Insert the batteries according to the positive (+) and (-) side indicated on the device. 1 2 3 4 2020 Aztech Technologies Pte Ltd. All rights reserved. 3. Replace cover. Place the back cover and push to lock. PAIRING THE DEVICE Requirement:

iOS 12.0 or later Android 5.0 or later 1. Download and sign in to Kyla App from Google Play/App Store. Press and hold the reset button for at least 5 seconds until Red LED starts to blink. RESETTING THE DEVICE TECHNICAL SPECIFICATIONS 4. Battery Removal. 2. Press and hold the reset button for at least 5 seconds until Red LED starts to blink. NOTE: LED will blink rapidly for approximately 30 seconds before connection time-out. SMART MOTION SENSOR EASY START GUIDE NOTE: LED will blink for 10 seconds to indicate low battery power. The estimated battery standby time is 8 to 12 months. NOTE: This device only works with a Smart Hub. If the device is undetectable, reset the device and try again. 3. From the App, select Add Device > Sensors

> Smart Motion Sensor > (select existing Smart Hub) Pair 5 6 7 8 FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 5mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

confidential: This drawing is confidential and proprietary to Aztech. Reproduction in whole or in part is prohibited without the written consent of Aztech. 1.0 02-MAR-2020 2.5mm m m 9 Smart Motion Sensor Model No: KSEN-210-ZB Made in China 50.4mm 44.6mm LASER MARKING PARAMETERS :

(kHz)

() 2500 70 45 1 0.1 200 0 () 0.05 () V () 1 V () V (/)

-0.23 0.1 0.3 0.3 2000 0.2 TOOLING P/N: M19-086-000

*ALL GRAPHIC MEASUREMENTS/DIMENSIONS COMES WITH TOLERANCE OF +/- 0.3MM UNLESS STATED OTHERWISE.

*ALL LASERMARK MEASUREMENTS/DIMENSIONS COMES WITH TOLERANCE OF +/- 0.3MM UNLESS STATED OTHERWISE. CRUSADE CHAU PATRICK LIM PATRICK LIM 261-0255090-000 Form #: 16-0 (QP-4.5-1)

AZTECH TECHNOLOGIES PTE LTD Company: AZTECH TECHNOLOGIES PTE LTD Address: 31 Ubi Road 1, #01-05, Singapore 408694 Product Name: Smart Motion Sensor Model Number(s): KSEN-210-ZB Product Description: Smart Motion Sensor We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: 2020-9-11 Signature:

Name:

Bruce Wu Title:

Senior R&D Engieer Company: AZTECH TECHNOLOGIES PTE LTD

AZTECH TECHNOLOGIES PTE LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020-9-11 Subject; Request for Confidentiality FCC ID: I38KSEN210ZB To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Bruce Wu Title: