AW-CU302 IEEE 802.11 b/g/n + Bluetooth 4.2 LE WLAN/BT Microcontroller Module Datasheet Version 0.7
- 1 -
Document release Date Modification Initials Approved Version0.4 2016/11/23 Initial (New Solution) Kai Wu Daniel Lee Version0.5 2017/3/15 Version0.6 2017/4/1 Version0.7 2017/8/1 Redesign:
- Support external ANT for WLAN
- Only 3.3V power supply Redesign:
- RF DPDT switch
-
Redesign:
-
- Added Debug pins 32.768KHz(Crystal +Oscillator) 32.768KHz(Oscillator) Kai Wu Daniel Lee Kai Wu Daniel Lee Alex Yu Daniel Lee
- 2 -
2.1 2.2 2.3 2.4 1.1 1.2 1.3 1.4 5.1 5.2 5.3 5.4 5.5 5.6 Index 1. GENERAL DESCRIPTION ............................................................................................................... 4 PRODUCT OVERVIEW AND FUNCTIONAL DESCRIPTION ................................................ 4 KEY FEATURES .................................................................................................................... 5 FUNCTION BLOCK ............................................................................................................... 6 SPECIFICATIONS TABLE ..................................................................................................... 7 2. ELECTRICAL CHARACTERISTICS ............................................................................................. 8 ABSOLUTE MAXIMUM RATINGS ......................................................................................... 8 RECOMMENDED OPERATING CONDITIONS ..................................................................... 8 INTERNAL MEMORY ............................................................................................................ 8 EXTERNAL 32KHZ CRYSTAL REQUIREMENTS ................................................................. 8 3. APPLICATION: .................................................................................................................................. 8 4. BELOW ARE THE SPECIFICATIONS FOR THIS CRYSTAL. ................................................ 9 5. PIN DEFINITION ............................................................................................................................. 10 POWER PIN ........................................................................................................................ 10 GPIO [88MW300] PIN .......................................................................................................... 10 GPIO [DA14580] PIN ........................................................................................................... 11 GROUND PIN ...................................................................................................................... 12 FLOATING PIN .................................................................................................................... 12 DEBUG PIN ......................................................................................................................... 13 6. CONFIGURATION PINS ................................................................................................................ 14 POWER PIN ........................................................................................................................ 14 CLOCK [88MW300] PIN ...................................................................................................... 14 GROUND PIN ...................................................................................................................... 14 7. MECHANICAL CHARACTERISTICS ......................................................................................... 15 6.1 6.2 6.3
- 3 -
1. GENERAL DESCRIPTION 1.1 PRODUCT OVERVIEW AND FUNCTIONAL DESCRIPTION AzureWave presents AW-CU302 Wi-Fi/BT Microcontroller Smart Energy Platform Solution provides a highly cost-effective, flexible and easy to-use hardware/software platform to build a new generation of connected, smart devices. These smart-connected devices enable device to deliver a broad-range of services to consumers including energy-management, demand-response, home automation and remote access. This allows a user to manage comfort and convenience, also run diagnostics and receive alerts and notifications, in addition to managing and controlling the device. Developers can leverage the rich connectivity features of these new smart devices to create a new generation of innovative new applications and services The platform builds upon the success of Marvells first-generation Wi-Fi/BT microcontroller platforms using the Marvell/Dialog 88MW300/DA14580 Wi-Fi/BT System-on-Chip (SoC), a 4MByte QSPI flash memory and Marvell Easy Connect software.
- 4 -
1.2 KEY FEATURES MCUs of AW-CU302 g 88MW300 (Marvell 88MW300 is a WLAN IEEE 802.11 b/g/n standalone SoC) Processor ARM Cortex-M4F, 32bit 200MHz main bus clock Memory 128KB ROM 512KB RAM Flash Controller 32KB SRAM cache to support XIP Memory-mapped access to QSPI Flash devices Wireless IEEE 802.11 b/g/n HT20 Low-power with deep sleep and standby modes Fully supports clients (stations) implementing IEEE Power Save mode Wi-Fi direct connectivity g DA14580 (Dialog DA14580 is a Bluetooth Low Energy 4.2 SoC) Processor ARM Cortex-M0, 32bit, 16MHz Dedicated Link Layer Processor AES-128 bit encryption Processor Memory 42 KB System SRAM 84 KB ROM 8 KB Retention SRAM Wireless Bluetooth V4.2 Memory of AW-CU302 g 4M Byte QSPI flash IO Interfaces g UART g SWD(JTAG) g SSP(SPI) g GPT(PWM) g I2C g ADC g GPIO Wireless g Wi-Fi 802.11 b/g/n only HT20 g Bluetooth V4.2 Package g LGA Module 36 mm x 18 mm x 2.5 mm 111 pin Antenna Internal Chip Antenna for WLAN/BT coexistence or BT only g g External U.FL connector for WLAN only Certifications g TBD
- 5 -
1.4 SPECIFICATIONS TABLE Product Description AW-CU302 Wireless Smart Energy module WLAN Standard BT Standard Host Interface Major Chipset Dimension Package IEEE 802.11b/g/n, Wi-Fi compliant Bluetooth V4.2 complaint UART/JTAG/SSP/I2C/ADC Marvell 88MW300 + Dialog DA14580 + 4MB flash 36 mm x 18 mm x 2.5 mm 111-pin LGA Operating Conditions Voltage Temperature 3.3V +/- 9%
Operating: -30 ~ 85; Storage: TBD Electrical Specifications Frequency Range 2.4 GHz ISM radio band Number of Channels Modulation Output Power Receive Sensitivity Antenna Data Rates 802.11b: Channel 1(2.412GHz)~13(2.472GHz) 802.11g: Channel 1(2.412GHz)~13(2.472GHz) 802.11n(HT20): Channel 1(2.412GHz)~13(2.472GHz) DSSS, OFDM, DBPSK, DQPSK, CCK, 16-QAM, 64-QAM for WLAN GFSK (1Mbps), /4 DQPSK (2Mbps) and 8DPSK (3Mbps) for Bluetooth WiFi: FCC/IC 290.402mW BLE :FCC/IC :0.9183mW BLE:
-TBD
-
WLAN:
-TBD Bluetooth:
-TBD Function1: Internal Chip Antenna for WLAN/BT coexistence. Function2: Internal Chip Antenna for BT only, u.FL(external antenna) for WLAN only WLAN:
802.11b: 1, 2, 5.5, 11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: MCS0-7,up to 72.2Mbps(20MHz channel ) Bluetooth:
Bluetooth Low Energy Only
- 7 -
4. BELOW ARE THE SPECIFICATIONS FOR THIS CRYSTAL.
- 9 -
5. PIN DEFINITION 5.1 POWER PIN Pin No Definition Basic Description Type Level A10 VBAT_WL_3V3 88MW300/FLASH power supply. (Pin A10 with Pin B10 configuration) B10 VBAT_WL_3V3 88MW300/FLASH power supply. (Pin A10 with Pin B10 configuration) A11 VBAT_BT_3V3 DA14580 power supply. (Pin A11 with B11 configuration) B11 VBAT_BT_3V3 DA14580 power supply. (Pin A11 with B11 configuration) A13 VPP_BT_6V8 This pin is used while DA14580 OTP programming and testing. OTP programming: VPP = 6.7 V 0.1 V OTP Normal operation: leave VPP floating A, I A, I A, I A, I 3.3V 3.3V 3.3V 3.3V A, I 6.8V 5.2 GPIO [88MW300] PIN Pin No Definition Function 0 Function 1 Function 2 Function 3 Function 4 Function 5 Type Level J4 J6 GPIO_0 GPIO_1 GPIO_0 GPIO_1 GPT0_CH0 UART0_CTS SSP0_CLK GPT0_CH1 UART0_RTS SSP0_FRM K7 GPIO_2(4) GPIO_2 GPT0_CH2 UART0_TXD SSP0_TXD K6 GPIO_3(4) GPIO_3 GPT0_CH3 UART0_RXD SSP0_RXD B7 GPIO_4 A4 GPIO_5 GPIO_4 GPIO_5 GPT0_CH4 I2C0_SDA AUDIO_CLK GPT0_CH5 I2C0_SCL B5 GPIO_7(2) JTAG TCK GPIO_7 UART2_CTS SSP2_CLK I2C0_SDA A5 GPIO_8(2) JTAG TMS GPIO_8 UART2_RTS SSP2_FRM I2C0_SDL A6 GPIO_10 JTAG TRST GPIO_10 UART2_RXD SSP2_RXD I2C1_SDL E1 GPIO_16(1) GPIO_16 CON[5]
AUDIO_CLK A3 GPIO_23 WAKE_UP_1 GPIO_23 UART0_CTS B1 GPIO_24(3) OCS32K GPIO_24 UART0_RXD GPT1_CH5 C1/J9 GPIO_25(3) XTAL32K_IN GPIO_25 I2C1_SDA D1 GPIO_26(3) XTAL32K_OU T GPIO_26 I2C1_SCL F1 GPIO_27(1) GPIO_27 CON[4]
UART0_TXD H1 GPIO_40 GPIO_40 G1 GPIO_41 GPIO_41 ADC_DAC_TR IGGER0 ACOMP0_GPI O_OUT ACOMP1_GPI O_OUT ADC_DAC_TR IGGER1 ACOMP0_ED GE_PULSE ACOMP1_ED GE_PULSE K4 GPIO_46 GPIO_46 ADC_4/
ACOMP4 UART2_CTS SSP2_CLK COMP_IN_P COMP_IN_N I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V
- 10 -
I/O I/O I/O I 3.3V 3.3V 3.3V 3.3V(internal pull high 51k ohm) K2 GPIO_47 GPIO_47 K3 GPIO_48 GPIO_48 K5 GPIO_49 GPIO_49 ADC_5/
ACOMP5 ADC_6/
ACOMP6 ADC_7/
ACOMP7 UART2_RTS SSP2_FRM UART2_TXD SSP2_TXD UART2_RXD SSP2_RXD A2 RESETN_WL RESETn Host reset
*(1) Configuration Pins Table:
Pin No Definition Function 1 Description (Configuration Bits) AW-CU302 F1 E1 GPIO_27 GPIO_16 88MW300 Boot Options with CON[4], CON[5]
00 = boot from UART 11 = boot from internal QSPI Flash (default)
*(2) 32k clock reference (sleep clock)
*(3) SWD support on GPIO_7 (SWDCLK) and GPIO_8 (SWDIO)
*(4) Console UART0 on GPIO_2 (TXD) and GPIO_3 (RXD)
- External crystal-oscillator driving 32.768 KHz clock to GPIO_25
- External crystal connected to GPIO_25 & GPIO_26 at 32.768 KHz
- Connect GPIO_24 to GPIO_25 for calibration reference to RC32K 5.3 GPIO [DA14580] PIN Pin No Definition Function Type Level J11 GPIO_0_0_BT J10 GPIO_0_1_BT J8 GPIO_0_6_BT H12 GPIO_1_0_BT K9 GPIO_1_1_BT K13 GPIO_2_3_BT J13 GPIO_2_4_BT B13 GPIO_2_5_BT GPIO_2_6_BT GPIO_2_7_BT GPIO_2_8_BT GPIO_2_9_BT B9 A8 B8 A7 K8 Support ADC[0]. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Support ADC[1]. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. Pull-down enabled during and after reset. General purpose I/O port bit or alternate function nodes. 5(6(7B%7 5(6(7B%7
5(6(7B%7 5(6(7B%7 5HVHWVLJQDODFWLYHKLJK0XVWEHFRQQHFWHGWR*1'LIQRWXVHG
J12 SWCLK_BT K12 SWDIO_BT JTAG Data input/output. Bidirectional data and control communication. Can also be used as a GPIO. INPUT JTAG clock signal. Can also be used as a GPIO. K10 XTAL32Kp INPUT. Crystal input for the 32.768kHz XTAL. K11 XTAL32Km OUTPUT. Crystal output for the 32.768kHz XTAL.
- 11 -
AIO AIO I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I/O I/O I O 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V(internal pull low 2.2k ohm) 3.3V 3.3V 3.3V 3.3V 5.4 GROUND PIN AW-CU302 Pin No Basic Description
****
****
****
++++
++++
++++
----
----
....
....
....
$$$$
$$$$
$$$$
$$$$
$$$$
%%%%
%%%%
%%%%
%%%%
&&&&
&&&&
&&&&
&&&&
&&&&
&&&&
&&&&
&&&&
''''
''''
''''
''''
''''
''''
''''
((((
((((
((((
((((
((((
((((
((((
))))
))))
))))
))))
))))
****
****
****
****
****
****
5.5 FLOATING PIN GND(CONFIGURATION PINS) AW-CU302 Pin No Basic Description B4 C2 D2 E2 G2 F2 H2 J1 FLOATING PIN
(FLOATING)
- 12 -
5.6 DEBUG PIN AW-CU302 Pin No Basic Description F14 F3 J5 E3 G14 DNS(Dont connect)
- 13 -
6,'(6,'(6,'(6,'(9,(:9,(:9,(:9,(:
- AW-CU302 Drawing 7239,(:
7239,(:
7239,(:
7239,(:
- 16 -
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID:
7/=&8. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: $&8. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: $&8". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. 1. 2. XXXyyyLPDzzzz-x