FCC ID: 2AT4D-Z5EA05PFCC02 13.56MHz RFID Reader/Writer

Issued4.22.2020 No. T716301De Easy ID/5bit system Read System Reader Z5-EA05N-_ _ , Z5-EA05P-_ _ Z5-EA05BKN-_ _ , Z5-EA05BKP-_ _ Z5-EA05P-FCC-02 Z5-EA05BKP-FCC-02 Manual 5bit Contents Description 1.1 Description 3 1.2 System configuration 3 1.3 Each role 3 1.4 5bit format system 3 2. Specifications 4 Installation and Wiring 5 4. Communication with the External Unit 8 Available ID tag and reading distance 10 Safety Considerations

(Please read through before use) Before using this product, please carefully read this instruction manual, pay attention to safety, and handle it properly. Design considerations This product constitutes the identification system together with the ISO 15693 compliant ID tag. Please do not use for other uses. Please design the system so that the entire system works on the safe side even if the external power supply malfunction or this product breaks down Please design the system carefully and not to exceed the range of the equipment specification described in this instruction manual for power supply / usage conditions. Usage considerations Use a regulated power supply, e.g. switch-model type. There is a risk of fire or heat generation exceeds the rated voltage power is being supplied"

"When wiring the processor, follow the chapters containing the wiring diagrams closely, and wire all connections properly. When installing, maintaining, troubles etc. concerning this product, be sure to turn off the power, please go. Do not disassemble or modify the processor. Which may cause failure,malfunction, injury or fire. To avoid malfunction caused by induction noise, cable should be kept apart from motor or other power cable. When disposing of the processor, treat it as industrial waste. Incorrectly connected wiring may cause malfunction or unexpected problems."

The 5bit system is an ID system that easily reads 5bit data without any special program. This Read-Only system needs no particular program to read data, for the Reader reads data of a Data carrier when the Data carrier come into the reading area of the reader. The 5bit system is an ID system that easily reads 5bit data without any special program. An ID reader / writer (Z6-01-U) is available for writing data. The 5bit system uses the ISO 15693 compliant ID tag and occupies the first 3 bytes (00, 01, 02 address) of Description

.1 Description automatically the tag memory as the data area. System Configuration IDreader ID tag Sequencer input unit

. 3Each role ID tag ID Reader Memory that stores information. Use the first 3bytes in the 5bit system. A device that reads the information stored in the ID tag. (This product) When the ID tag enters the communicable area, it automatically reads the data and the read data is output as a 5-bit parallel signal. Used frequency / 13.56MHz

. 45bit system format ID data is stored in a format for a 5bit system. The first 1 byte (5 bits of 00 address) is the ID data of the user, the next 2 bytes (5 bits of 01 and 02 address) are used for data check. This format is called a 5bit system format. When reading, the ID reader compares and processes the 5bit data stored in the above 3 addresses When the comparison result is positive, After outputting 00 address data as read data, then turn on valid data output. If the comparison result is incorrect, Blinks LED (low speed) as data check error. At this time the output does not change.

(Example) 7 00H address X 01H address X 02H address X 6 X X X 5 X X X 4 0 1 1 3 0 1 1 2. 1 0 0 1 0 1 1 0 0 1 1 Writing data Check data 04H( )

1BH( ) 1BH( ) Data bit No.

(*) Describe the upper 3 bits assuming "0"

Xoption Z5-EA05P-_ _ Z5-EA05BKP-_ _ PNP output Z5-EA05P-FCC-02 Z5-EA05BKP-FCC-02 PNP output Z5-EA05BKN-_ _ NPN output DC24V 10%(Including ripple) 50mA or less 6 points (ID data signal: 5 points, data valid signal: 1 point) DC30V Up to 50 mA per output 1.5V or less Short-circuit protection 0.08mA or less 50 ms (automatic reading) Impossible (installation on metal surface is acceptable) 0 50 /35 90%RH 0 50 /35 90%RH LED (3 places) ID tag lights on when completing data reading / ID tag blinks with data check error 50 M or more (Between charging unit and case between DC 500 VM) AC 1000 V / 1 minute (Battery Charging Batch and Case) 10 to 55 Hz, 1.5 mm amplitude, 2 hours in each of X, Y, Z directions 50 G, three in each of the X, Y, Z axial directions, 18 times in total IP67 Case: PBT (GF 30%), back cover: aluminum PVC 5.58XAWG24 Body20g cable 50g/m M4 / 1.2Nm This machine has built-in high-frequency equipment that acquired the following type designation. Z5-EA05N-_ _Ministry of Foreign Affairs Designated No. AC-16019 Z5-EA05P-_ _Ministry of Foreign Affairs Designated No. AC-16020 CE CE , FCC 2. Specification General specification Type code Case color (Orange) Z5-EA05N-_ _ Case color (Black) Output specification Supply voltage Current consumption Number of output points The output load voltage Output load capacity Output remaining voltage Output circuit protection Output leakage current ID tag data reading time Metal embedding Operating temperature / humidity Storage temperature / humidity Data valid LED Insulation resistance Voltage endurance Vibration rating Shock rating Protection class Housing material Cable Weight Mounting screw / tightening torque Applicable regulations Compliance standard Demension 5 2 The Z5-EA05BK* series has a black case color, but other specifications are the same as the Z5-EA05 series. Z5-EA05(BK)N-_ _ , Z5-EA05(BK)P-_ _ Z5-EA05(BK)P-FCC-02 10 LED(3) data valid LED ID Active surface 2-4.1

() 8 2- 7.5 depth 4.2 2-7.54.2 5 1 Cable bend radius : 50 mm 10 50 L 2m L = Cable length Standard : 2m ( Max 10m ) Cable color Signal name Power (24V) Power supply 0V Read data D0 Read data D1 Read data D2 Read data D3 Read data D4 Data valid DV 5 2 I/O IN IN Out Out Out Out Out Out LED(3) Cable color Meaning White Black Brown 10 Red Yellow Green Blue Gray 8 ID 2-4.1

() Power supply input (24V) Power supply input (0V) Output data read from Bit address [ 0 ]

Output data read from Bit address [ 1 ]

Output data read from Bit address [ 2 ]

Output data read from Bit address [ 3 ]

Output data read from Bit address [ 4 ]

Output signal that indicates the read data is valid 2-7.54.2 5 1 10 50 2m LED display contents Condition ON OFF Blinking

(Quickly) Blinking Meaning A state in which data can be correctly read from the tag and data is being output.

(Keep lit for 0.5 to 0.7 seconds even if the tag is out of communication area while it is lit.) The tag is out of the communication area. (All outputs are off.) Output over current condition. (Repeat with 50ms on and 50ms off. Over current protec-

tion works. ) Data check error condition. (Repeats 0.5 second lighting and 0.5 second light off.) slowly

(All outputs are off.) Output Equivalent Circuit Diagram NPN type Z5-EA05(BK)N-_ _ ID reader ID Internal cercuit 24V Load

OUT D0 4 Data valid) 0V Installation and Wiring Installation Surrounding metal Mounting on metal surface: Enabled Embedding in metal: Not permitted Nonmetallic region when embedded in metal metal A metal B A 20mm B 20mm C 0mm D Mutual interference PNP type : Z5-EA05(BK)P-_ _ Z5-EA05(BK)P-FCC-02 ID reader ID Internal cercuit 24V OUT D0 4 Data valid)

Load 0V Cable bend radius 33mm 33mm A C 10mm (up to the thickness D of the antenna) When cables are bent and wired, Please secure a bending radius of 33mm or more. Do not pull the cable with excessive force. When installing the ID reader, in order to avoid mutual interference be-

tween ID readers please set it at an interval more than the value shown in the table below. Tightening torque 1.2Nm Parallel face to face Parallel 60 mm Face to face 100 mm Wiring Diagram NPN type]

Reader Z5-EA05(BK)N-_ _ External Power Unit Host device 24V 0V White Black Brown Red Yellow Green Blue Gray White Black Brown Red Yellow Green Blue Gray Data Input D0 Data input D1 Data input D2 Data input D3 Data input D4 Data valid input DV Data Input D0 Data input D1 Data input D2 Data input D3 Data input D4 Data valid input DV

[ PNP type ]

Reader Z5-EA05(BK)P-_ _ Z5-EA05(BK)P-FCC-02 External power supply Host device 24V 0V Attention

- Maximum cable length between Reader and external device is 10 m.

- The Z5-EA05(BK)P-FCC-02 must be installed with the included ferrite core and noise filter on the cable and power supply line (black and white). Please refer to the next page for installation.Cables up to 2m are FCC compliant. About FCC Certification the following two conditions:

Z5-EA05P-FCC-02 and Z5-EA05BKP-FCC-02 complies with part 15 of the FCC Rules. Operation is subject to

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation of Z5-EA05(BK)P-FCC-02

[ Installation ]

The ferrite core and the noise filter must be properly installed as follows in order to comply with the FCC 7 1 cm 7 1 cm ID reader Z5-EA05P-02 or Z5-EA05BKP-02 Ferrite core clamp E04SRS251512 2 turns Ferrite core clamp E04SR401938 3 turns About 10 cm About 10 cm Ferrite core clamp E04SR200932 6 turns Brown Blue Noise filter RSEL-2001W Brown Blue White Black Brown Red Yellow Green Blue Gray Type code Company Name Indication of Japan's Ministry of Internal Affairs and Communi-

cations designation FCC ID Wiring the power lines The cable used for the wiring from the noise filter to the power supply must be prepared by the customer and wrapped around a 6T ferrite core clamp. Recommended CableAWG24 or 26Any colorAbout 70cm Changes or modifications not expressly approved by the party responsible for compliance could void the user's CAUTION authority to operate the equipment. 4. Communication with the External Unit Data Reading Timing Chart 1 In case of normal reading Min.500ms Max.700ms Min.500ms Max.700ms ID tag ID Min.500ms Max.700ms ID tag ID Min.500ms Max.700ms ID DV ID DV D0D4 DV D0D4 DV Max.50ms 1030ms Min.500ms Max.700ms Max.50ms 1030ms D0D4 D0D4 When the ID tag enters the communicable area during the output data holding period of the ID tag ID ID ID Min.500ms Max.700ms ID tag ID Data valid ID

(DV) Yes No ON OFF Read data

(D0D4)

(DV) ON ON OFF OFF

(D0D4) ON OFF Timing Chart 2 Yes ON No OFF ON ON OFF OFF ON OFF ID tag ID

(DV) Data valid

(D0D4)

(DV) Read data

(D0D4) ID tag ID DV ID tag ID DV

DV D0D4 D0D4 DV

D0D4 D0D4 Max.50ms 1030ms 130150ms Max.50ms Max.50ms 1030ms 130150ms Max.50ms

[ Procedure for Communication ]

area of the reader and set the read data. Note

(1) Reader reads the data of the Data carrier automatically as soon as the Data carrere comes into the communication

(2) The host computer should start reading from D0 to D7 of Reader after checking the data valid signal turns ON. If there are multiple ID tags in the communication area, data valid (DV) will not be turned on. If a data check error occurs, the data valid (DV) remains OFF and the read data is not output. In this case, the LED flashes (0.5 second lights on, 0.5 second off). Available ID tag and reading distance metal A C Applicable Data carrier Z1-AA04-02K, Z1-EC02-128, Z1-EA02-128, Z1-FA01-128, Z1-FB01-128 A distance of 200 mm or more is required between the tag and its surrounding A. (See below) Metal attachment refers to a state where it is installed directly on a metal (C:0 mm). Nonmetallic attachment refers to a state in which the metal and the tag are installed with securing a certain distance (C) or more on the back side. Communication dis-

tance and axis deviation values are all reference values. Z1-AA04-02K Nonmetal domain (A:) Z1-EC02-128 70mm) Metal mounting C:0mm Non-metal mounting C:20mm 0...10 0...12 Condition of the installment Communication distance (mm) Center offset Distance Non-metal domain Metal Non-metal mounting mounting C:0mm C:20mm 0...12 0...12 7 0mm 5mm 8 10mm 7 12mm 0

7 8 7 0

Z1-EA02-128 Non-metallic area (A :

Z1-FA01-128 Z1-FB01-128 Condition of the installment Communication distance (mm) Center offset Distance 5 0mm 4mm 5 8mm 4 10mm 0 12mm

Condition of the installment Communication distance (mm) Center offset Distance 0mm 2 3mm 3 5mm 0 7mm

6 7 7 6 0 0...7 3 4 4 0

30mm) Metal mounting C:0mm 0 5.5 Non-metal mounting C:20mm Condition of the installment Communication distance (mm) Center offset Distance 0mm 5mm 10mm 15mm Non-metal domain A56mm Non-metal mounting C:20mm 0...15 4 6 6 0

Non-metal domain A70mm Non-metal mounting C:20mm 0...19 10 12 12 8 0 Condition of the installment Communication distance (mm) Center offset Distance 0mm 5mm 10mm 15mm 19mm Z1-B011-128 has different offset depending on the moving direc-

tion of Data carrier. When its installed as described below, up and down movement means vertical direction, left and right movement means lateral di-

rection. Z1-BO11-128 Condition of the installment Metal mounting Nonmetal domain (A:) 70mm) Non-metal mounting C:0mm Moving direction of Data carrier. Communication distance (mm) Center Distance offset Side Vertical Side Vertical C:20mm 0...12 0...12 0...12 0...12 15 7 15 7 0mm 5mm 15 10mm 10 12mm 0

8 5 0

15 10 0

8 5 0

Wireless Power Supply by Mail b-plus-usa@b-plus-kk.com Web http://www.b-plus-kk.com

* Info may change the mention contents such as specifications without a notice. Thank you for understanding

* Please refer to instruction manual or the user's guide. It can be download by HP. v e r t i c a l lateral

[ Installation ]

7 1 cm 7 1 cm ID reader Z5-EA05P-02 or Z5-EA05BKP-02 Ferrite core clamp E04SRS251512 2 turns Ferrite core clamp E04SR401938 3 turns About 10 cm About 10 cm Brown Blue Noise filter RSEL-2001W Brown Blue

[ Marking tube part ]

Type code Company Name Indication of Japan's Ministry of Internal Affairs and Communi-

cations designation FCC ID White Black Brown Red Yellow Green Blue Gray Ferrite core clamp E04SR200932 6 turns

[ All marking tube ]

[ Marking tube for FCC ID ]

Font size : about 2mm The rubber tube which with FCC ID is a heat-shrinkable tune and it is difficult to remove it because the tube is fused together by the manufacturer.

[Material of Marking tube]

Manufacturer: SUMITOMO ELECTRIC INDUSTRIES, LTD. Product name: SUMITUBE F(Z) CAT 939 Tube Size: 8 0.25 (Gray) After recovered (mm): 4.00 (Inside diameter (max.)), 0.56 (Wall thickness (min.))

'BAPLUS. net C=--PokK-IaAR Date: April 16, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Gc. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize Takeshi Choda, Project Coordinator of Japan Quality Assurance Organization and hereafter referred to as JQA, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Takeshi Choda, Project Coordinator of JQA on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing JQA as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

Cc) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

g) h) j) k) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; |

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Ng dade Date: Apri 16, 2020 Name: Yuji Kubota Telephone: +8 1-493-71-6552 E-mail: kubota_yuji@b-plus-kk.jp Signature:

Model Declaration Letter We, the undersigning company Company Name: B&PLUS KK Address: P.O. Box 355-0311 2452-5, koya, Ogawa-machi Hereby confirm that the following products:

Product description: 1) Color of the cabinet is Orange. 2) Color of the cabinet is Black. Type designation: 1) Z5-EA05P-FCC-02 2) Z5-EA05BKP-FCC-02 Trademark: B&PLUS That All versions of the Model Z5-EA05P-FCC-02 and Z5-EA05BKP-FCC-02 are electrically equal except the following difference:

color of the enclosure. 1. Z5-EA05P-FCC-02 has the same PCB design as Z5-EA05BKP-FCC-02, different has each Date: April 16, 2020 Name: Yuji Kubota Telephone: +81-493-71-6552 E-mail: kubota_yuji@b-plus-kk.jp

SB & PLUS. nate E--PIORK-IaA Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AT4D-Z5EA0SPFCC02 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Parts List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Best Regards Date: May 18, 2020 Name: Yuji Kubota Telephone: +81-493-71-6552 E-mail: kubota_yuji@b-plus-kk. jp