FCC ID: QYGHITAG2 HITAG 2.0 XSENSE SENSING UNIT

HiTag 2 User manual The Xsense HiTag is a sensing unit of the Xsense Cold Chain Monitoring System. Placed inside one of the product cartons in a pallet, it monitors the temperature and relative humidity of the products immediate environment. When an Xsense Communication Unit (CU) is in the vicinity, data is transmitted to the Xsense System and immediately viewable to users via the secure, web-based Xsense application. Activating the tag is a simple two step procedure:

1. Press and hold the button for one second until the LED starts flashing 2. Check that the indicator LED is flashing. NOTE: The indicator LED is located beneath the plastic casing. If it does not slowly flash and stops after 10 seconds the HiTag failed to activate FCC ID: QYGHiTag2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Warning Modifications not expressly approved by the manufacturer could void the user authority to operate the equipment under FCC Rules. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.

mem { BI9 Intelligent Supply Chain Solutions TEL. +972 (0)4 9152800 | FAX. +972 (0)4 9152801 | 33 Dolev St. | P.O.B. 54, Tefen Industrial Park, 24959 Israel XSENSEO RK HiTag2 c PCC ID: QYGHITAG2 Ss

Date:6/12/2012 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Shaike Raz of L.T.L. (Product Testing) Ltd (ITL) to sign FORM 731 on our behalf for the following application:

FCC ID: QYGHTAG2 Thank you, ov A BT 9 Ltd Signature: Tefen, Dok 33, 2480 3 Yossi Pelech Reg. NO R&D Director B.T9 Ltd. TEL. +972 (0)4 9152800 | FAX. +972 (0)4 9152801 | 33 Dolev St. | P.O.B. 54, Tefen Industrial Park, 24959 Israt

gent Supply Chain Solutions Date: 06 December 2012 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID:

QYGHITAG2. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

CONF APPENDIX HiTag 2 BlkDia.pdf CONF APPENDIX HiTag 2 PartsLst.pdf CONF APPENDIX HiTag 2 Schem.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, BT 9 Ltd Signature: Tefen, Doky 33, ; 1 Yossi Pelech Reg. N R&D Director B.T9 Ltd. TEL. +972 (0)4 9152800 | FAX. +972 (0)4 9152801 | 33 Dolev St. | P.O.B. 54, Tefen industrial Park, 24959 Israr

The HiTag referred to as the EUT in this report, is a Temperature and Relative Humidity Wireless Sensor which can log its samples or transmit them to the master unit (CU) through a proprietary wireless network. The HiTag may either transmit directly to the master unit or through another HiTag. When EUT comes in range of the CUs RF network they connect to it, directly or through other EUTs, and transfer their stored information to the CU. The wireless communication network band is RF ISM 433MHz and there are 4 possible channels frequencies:

Channel 1 433.75 MHz Channel 2 433.9 MHz Channel 3 434.05 MHz Channel 4 434.2 MHz The EUT RF is passive when no CU is adjacent (It listen only searching for a CU RF network). Declare maximum EIRP power:

-10 dBm@ 434 MHz Type of modulation:

FSK Antenna type:

External wire antenna 70 cm long The EUTs MCU MSP430G2533 is running on external 32KHz crystal for accurate clocking at low power modes and it uses internal calibrated 8MHz clock which divided by 2 and 4 to create a 4MHz and 2 MHz respectively internal clocks drivers. The EUT RF Transceiver is clocked by external 32MHs crystal. The EUTs power source: Single 3.0 V CR2450 or CR2 Lithium batteries.