FCC ID: GIFESERIESBT E-Series Ultrasonic with BadgerTouch

BadgerTouch Automated Meter Reading System Pit Module Model ESERIESBT and HREBT APPLICATION The Badger Meter BadgerTouch Pit Module with Twist Tight connector for connectivity with an E-Series Ultrasonic Meter or Badger Meter High Resolution Encoder (HR-E) is a complete electronically encoded close-proximity automated meter reading system, specifically designed for pit meter installations. This system can be used with currently available E-Series Ultrasonic 3 and 4 inch meters, and HR-E encoders with all Recordall Disc, Turbo, Compound, Combo, and Fire Series meters and assemblies. The Pit Module is designed to fit pit lid configurations up to 2 inches thick. BadgerTouch Pit Module 3.96 in. (101 mm) Pit lid 1.75 in. diameter hole 2 in. max. 3.30 in. (84 mm) Locking nut Black housing Twist Tight connector INSTALLATION Unpacking Location Carefully remove the BadgerTouch Pit Module from the shipping carton and inspect the assembly for any damage. Figure 1: BadgerTouch Pit Module with Twist Tight connector and E-Series Ultrasonic meter TESTING To ensure proper operation of the BadgerTouch meter reading system, the BadgerTouch Pit Module should be mounted through a predrilled hole in the pit lid. Minimum hole diameter required is 1-3/4 inch. The Pit Module contains electronic circuitry that is totally encapsulated to enhance reliable performance in most locations, under most conditions. Pit Module Installation Once the BadgerTouch Pit Module is secured through the pit lid and connected to the meter/encoder, the BadgerTouch system is ready for operation. No specific testing is required at the meter location regarding proper connections. Interrogation of each module will facilitate proper coordination of meters, modules and account. Use a VersaProbe or other equivalent reading device for interrogation of the installed BadgerTouch modules. 1. Remove the locking nut and the coil assembly from the Pit Module "mushroom" holder. LICENSE REQUIREMENTS To remove the coil assembly, squeeze the tabs at the bottom of the coil assembly, turn to unlock and pull the assembly out of the holder. 2. From the outside of the pit lid, insert the Pit Module holder through the lid. 3. Screw the locking nut (large diameter side up) onto the threaded tube of the holder until the locking nut fits snugly against the underside of the pit lid. See Figure 1. 4. Insert the coil assembly, which is connected to the lead wire, into the Pit Module holder, until it is fully seated in the holder. Turn the coil assembly until it locks into place. This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Any changes made by the user not approved by Badger Meter can void the users authority to operate the equipment. In accordance with FCC Regulations, Code of Federal Regulations Title 47, Part 2, Subpart J, Section 1091, transmitters pass the requirements pertaining to radiation exposure. However, to avoid public exposure in excess of limits for general population

(uncontrolled exposure), a 20 centimeter distance between the transmitter and the body of the user must be maintained during operation. 5. Coil up any excess wire inside the pit and tie the cable to avoid any damage. No license is required by the utility to operate a BadgerTouch meter reading system.

(continued on back) BTA-UM-00234-EN-06 (January 2020) Installation Manual D R A F T BadgerTouch Automated Meter Reading System Pit Module Model ESERIESBT and HREBT This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. BadgerTouch, E-Series, HR-E and Recordall are registered trademarks of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding contractual obligation exists. 2020 Badger Meter, Inc. All rights reserved. D R A F T

January 27, 2020 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 To Whom It May Concern:

Elite Electronic Engineering, Inc. is authorized to act on our behalf, until otherwise notified, for applications to Elite Electronic Engineering, Inc. We certify that we are not subject to denial of federal benefits that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b) to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you. Regards, Pamela Stokke-Ceci Assistant General Counsel

January 27, 2020 FCC ID: GIFESERIESBT IC ID: 1046A-ESERIESBT Request for Confidentiality Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, we, Badger Meter, Inc., hereby request permanent confidentiality for the block diagram, schematic, BOM, theory of operation, and product description presented for certification. In support of the Request for Confidentiality, the following is stated:

Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in assuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. Pamela Stokke-Ceci Assistant General Counsel Badger Meter, Inc