FCC ID: 2AG32EG2013BM11 LTE Indoor CPE

LTE Indoor CPE - EG2013B-M11 USER Manual 01 All rights reserved Baicells Technologies Co., Ltd. About This Document This document introduces the installation of Baicells LTE Indoor CPE. Baicells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of Baicells. Copyright Notice Disclaimer This specification is preliminary and is subject to change at any time without notice. Baicells assumes no responsibility for any errors contained herein. For more information, please consult our technical engineers. Revision Record Date Version Description 10 Aug,2020 Initial released. 01 Contact Us Baicells Technologies Co., Ltd.North America Address: 555 Republic Drive, Suite 200 Plano, TX 75074 E-mail: support_na@baicells.com Phone: +1-972-800-1157 Website: http://www.baicells.com 1. Shipping List Make sure you have got the following parts:

EG2013B-M11 Quick Guide RJ45 Ethernet cable AC adaptor 1 2. Hardware Introduction 2.1 Indicators No. Name Status Description 1 Power Steady On Power On OFF No Power Supply Steady On WiFi enabled 2 WLAN OFF WiFi disabled 3 TEL Blanking Data is transmitting. Steady On VoIP having registered OFF VoIP having not registered 4 SIGNAL Steady On The more turn light up, the stronger signal OFF The signal is too weak or no signal Blanking The page reload, restore to the factory setting by page, restore to the factory setting by reset button or software upgrade 2 2.2 Interface and Buttons No. Name Description 1 USIM card slot Insert the USIM card to the slot. 2 Reset Button 3 TEL (RJ-11) 4 LAN (RJ-45) Press Reset button for 3s~20s, the CPE will restore to the factory settings. Press Reset button over 20 seconds, the CPE will enable the escape mechanism. TEL interface connects to Telephone by RJ-11 cable. LAN interface connects to PC or other network devices (such hub or switch) by RJ-45 Ethernet cable. 5 6 DC-5V (power interface) Connect to the DC-5V AC adaptor. ON/OFF ON/OFF the CPE. 2.3 RF Specification Item Mode Table 2-1 RF Specification Description TDD LTE 3 Channel Bandwidth 10MHz/15MHz/20MHz MAX Output Power LTE Standard LTE Band 231 dBm 3GPP R9 Band48 LTE Antenna Gain 6.5 dBi Wi-Fi Specification 802.11b/g/n Frequency 2400MHz~2483.5MHz Wi-Fi Antenna Gain 2 dBi 4 3. Connect Device 3.1 Insert USIM Card Install USIM card according to following steps:

1. Open the protective cover of the card slot. 2. Insert USIM card into card slot according to the following figure. a) Close the protective cover of the card slot. DO NOT install or uninstall USIM card when the CPE is running. This operation will interrupt the performance of the CPE and the data stored in the USIM card may be lost. CAUTION:

3.2 Connect Cable Install CPE according to following steps:

1. Check whether the USIM card installation is correct. 5 2. Connect one end of the RJ-45 cable to LAN interface of the CPE, and the other end connect to PC. 4. Power on. 3. Insert DC-5V AC adaptor to the power interface. 3.3 Connect Network Set CPE according to following steps:

1. Open Internet Browser and type in the default IP address: https://192.168.1.1 2. In the user name/password text box, type in the default user name and password, admin/admin. On the right corner of the page, there is the icon of signal strength, the two different status is as follows:

LTE connects to Internet successfully. The signal indictor indicates the strength of the LTE signal. The more bars turn light up, the stronger signal, otherwise, the weak signal. LTE does not connect to the Internet, please check whether the setting is connect. 3.4 Connect Wi-Fi Set CPE according to following steps in web page:

1. Before establishing Wi-Fi connection, make sure your wireless terminal devices (such as notebook, ipad, smart phone) have the WLAN function. 2. When is steady on, the WLAN function of CPE has enabled. If you need to enable or disable the WLAN function, refer to help information in the web management page. 3. On the label of back view of the CPE, view the WLAN Name and WLAN Key

(WPA/WPA2) and record the value. 6 To avoid unauthorized user access to the WLAN, please modify the WLAN Name and WLAN Key (WPA/WPA2). For more detail information, refer to help information in the web management page. 4. Enable WLAN function on wireless terminals, and these devices start to search nearby available wireless network. 5. Choose the network that the name is the same as WLAN Name. Input WLAN Key (WPA/WPA2) according to hint. Note the capital and small letter. When the connection is complete, the page will display whether the connection is successful. 6. 7 4. Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Warning:

8

Baicells Model:EG2013B-M11 _ Power Rating: === 12V;1.5A WIFI SSID:XxXXXXXXXX WIFI Password:xxxxxxxx HUAN AO Web Site:xxx.XxXxx.XXX.XXX SN:120300003919AGQ0042 Username:admin a4 TOOL MUA OU recat ome 5 IMEI:867945040041012 ands: =

BancsiB6e cgotsew HN 0 0 WT LAN MAC:48BF740B9381 Baicells Technologies Co.,Ltd. ee eZ J A ee ae a a ay

Baicells Technologies Co., Ltd. Date: Aug. 12, 2020 File Name Schematics.pdf Block Diagram.pdf Operational Description.pdf Part List.pdf Tune-up Procedure.pdf Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AG32EG2013BM11 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Schematics Block Diagram Operational Description Part List Tune-up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang/ Manager Typed name and Title

Baicells Technologies Co., Ltd. Date: 8/13/2020 Subject: authorization for adding family models To whom it May concern, Statement We would like to confirm the product LTE Indoor CPE with models EG2013B-M11, EG3013B-M11 are same in all respects. Only the model names are different for different market requirement. Yours sincerely,

[signature]

[Back Huang]

[Manager]

[Baicells Technologies Co., Ltd.]

Baicells Technologies Co., Ltd. FCC ID: 2AG32EG2013BM11 POWER OF ATTORNEY Date: Aug. 12, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd.

(Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Aug. 11, 2021. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Baicells Technologies Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang / Manager Typed name and Title

Baicells Technologies Co., Ltd. Date: 2020-08-12 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AG32EG2013BM11 To Whom It May Concern:

Sincerely, Signature

[Back Huang]

[Manager]

[Baicells Technologies Co., Ltd.]

This letter is to statement that EG2013B-M11 / LTE Indoor CPE. has been tested according to FCC Part 15B by Waltek Services (Shenzhen) Co., Ltd. (Test Report No.: WTS20S05031126E). And the SDOC file, meetting the requirements of the FCC regulations, would been provided when the device is sold by the responsible party in US. The service will not be sold until the SDOC is provided. If the sale does not have an SDOC, all responsibility is the responsibility of the applicant.