FCC ID: 2AG32EG7010CM11N LTE Outdoor CPE

ATOM OD06 - EG7010C-M11 USER Manual 01 All rights reserved Baicells Technologies Co., Ltd. 1. Shipping List Make sure you have got the following parts:

EG7010C Quick Guide PoE Adapter Power Cord Standard Mounting Kits Optional Mounting Kits 2 2. Hardware Introduction 2.1 Indicators Identity Description Color Status Description MIU Yellow OFF Reserved.

Steady On Reserved. Blanking Reserved. Network state Indicator Blue OFF LTE disconnected. Steady On LTE connected. LTE SIM SIM status indicator card Yellow Steady On The SIM card is normal. Blanking is abnormal or not LAN 100Mbps Eth Indication Yellow OFF connection does not The SIM card inserted. Ethernet established. Steady On Ethernet connection is normal. Blanking Data is transmitting. Yellow OFF No Power Supply Steady On Power On LTEs, Green All OFF Signal is too weak to attach. Steady On According to signal strength in turn light PWR Power Indicator LTE Signal 5 Indicate Identity Description Color Status Description connection state signal strength and up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 2.2 Interface and Buttons Interface & Button Description PoE TF SIM RESET GND Connected to the PoE Power Adapter Support SD card Support 1.8V/3.0V USIM 2FF Long press over 10 seconds to restore the factory settings Connected to Earth by conductor Before installation, prepare the following support materials accordingly, as given below:

3. Installation Guide 3.1 Support Materials Item Description Ethernet cable Outdoor Shield CAT5E Shorter than 330 feet Ground wire 16mm yellow-green wire 3.2 Install USIM Card and Cables

(1) Screw the screw on the waterproof cover, and open the waterproof cover

(2) Insert the USIM card to the USIM slot. Note following the directions

(3) Connect the Ethernet cable to the PoE

(4) connect the ground cable to the port ground screw

(5) Close the waterproof cover and fasten the screw on the cover.

(6) Connected Ethernet cable to the power adapter. Pay attention to the power adapter interface directions.

(7) Power on, the LED indicator will light up. 3.3 Install on Wall 1. Slipping the bracket from the CPE. 2. Fit the CPE on the wall, and mark the drilling locations. 3. Drill four 10mm diameter and 70mm depth holes in the wall by following the marked locations. tapping screws. 4. Check the up/down direction of the bracket, and then fix it on wall using M5 5. Install the CPE to the bracket and fasten the screw. 3.4 Install on Pole 1. Round an anti-slip rubber on the pole. 2. Fix the bracket using the hoop. 3. Install the CPE to the bracket and fasten the screw. 3.5 Grounding The EG7010C-M11 must be grounding, please contact professional person to operation. Using grounding cable, connect the grounding cable to the ground row 4. Configuration Guide 4.1 4.1 Login The CPE manages, configures, and maintains the device by web management page. The steps to log in are as follows:

1. In the address column of browser, type in http://192.168.150.1, then press Enter:

2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 4.2 View Status In the overview area, you can view the device information and LTE status,such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown below:

8 SAS Settings, as shown below:

5. Specifications Basic Specifications Item Description UE-Category 3GPP R10, CAT 6/7 USIM Slot 1.8V/3.0V USIM 2FF Ethernet Port Power Supply Reset Button 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX, PoE Input: Universal range 100V~240V AC Output: PoE (24V DC, 0.5A) Tactile button. Long press over 10s to restore the factory settings LED Indicators MIU/LTE/SIM/LAN/PWR/LTE Signal Dimensions 241mm (H) x 154mm (W) x 50mm (D) Weight About 900 g LTE Specifications Item Description LTE Mode LTE-TDD LTE Bands TXRX Band 48 2T4R Channel Bandwidth 5MHz, 10MHz, 15MHz, 20MHz 10 Modulation QPSK, 16QAM Receive Sensitivity

-94dBm @ QPSK,20MHz, 25C MAX Output Power 26dBm Antenna Type Internal directional-antenna Antenna Gain 14dBi@3.xGHz, 2 Ports 45

>70%

-25dB 2 Polarization Antenna Efficiency Isolation VSWR Horizontal Beam Width (3dB) 603@3.xGHz, 2 Ports Vertical Beam Width (3dB) 255@3.xGHz, 2 Ports SW Specifications Item Description Language Support English/Chinese Network Mode NAT/Bridge/Tunnel IP Protocol IPv4/IPv6 SIM Management PIN Management, SIM Lock Network Connection Management Auto/Manual LTE Scan Mode Full band scan, Frequency Lock WLAN VPN WPS MSSID Isolation VLAN L2TP GRE Port forwarding DMZ ALG Port Trigger Access Control Block Port Scanner / SYN Flood SPI Filter IP/MAC/URL Filter TR069 SNMP TCPDump Ping Trace route Device Status DHCP Client List WiFi Station List Firewall Status LTE Status LTE Status/Connection Time/System Up Time Date & Time setting Reboot Restore factory settings Restore / Back up configuration file Firmware upgrade locally/OTA (over the air) Operating Log Run-time Log Filter/Select/Display/Export Log Network Management NAT Firewall Diagnostics Statistics Maintenance System Log Environmental Specifications Item Description Operating Temperature

-40C to 55C Storage Temperature

-40C to 70C Operating Humidity 5% to 95%

Ingress Protection Rating IP65 6. Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio/TV technician for help. connected. Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator &

your body. 1

I Batcells Model:ec7010c- M11 Power Rating: ===24V;0.6A Web te:192. 16.1604 LOAN ATA Username :admin SN:12030000411843TP0082 Password:admin:

Password x] COI IME1:865799030204938 FOCID:2AG32EG70100M11N

- - CUTAN Baicells Technologies Co.,Ltd. Law mac:4ser74030140 eee ge ee nat J 45 6 7 & 9 101-2 aan oeee fos) S 20 \ 2 5 Ro Saeee

, an Nunn Nena eee No \

Bai Cells Mdel:EG701 OC- M pwerRating:

===24V;0.6A Web Site:192.168.1 50.1 Username :admi n Password:admin Bands:848 FCC ID:2AG32EG7010N Bai cells Technologies Co., Ltd.

Baicells Technologies Co., Ltd. File Name 2AG32EG7010CM11N _Block Diagram.pdf 2AG32EG7010CM11N _Schematics.pdf 2AG32EG7010CM11N _Operational description.pdf 2AG32EG7010CM11N _Tune up procedure.pdf 2AG32EG7010CM11N _BOM List.pdf Confidentiality Request regarding application for certification of FCC ID: 2AG32EG7010CM11N Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Circuit Diagram Operational Description Tune up procedure BOM List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signature:

Name/title: Back Huang /Certification Manager Company: Baicells Technologies Co., Ltd. Address: 9-10F,1stBldg.,No.81BeiqingRoad,Haidian District,Beijing,China E-mail: huanghu@baicells.com Tele: 86-010-62607100 Date: 2020/08/25 Rev 11/20/07

Declaration letter Dear Regulatory Authority, Please be notified that our Product: LTE Outdoor CPE Model name: EG7010C-M11 Use the orginal LTE Base Station,FCC ID: 2AG32EG7010CM11N RF conducted FCC Part 96 test data. The EUT only replay with a new Antenna, no other change FCC ID Category of CBRS Antenna Gain Any response related to this notification, please communicate directly with our agent. 2AG32EG7010CM11N(new) Category B 14dBi 2AG32EG7010CM11(original) Category B 11dBi If you have any question regarding this authorization, please do not hesitate to contact us. Sincerely yours, Signature:

Name/title: Back Huang /Certification Manager Company: Baicells Technologies Co., Ltd. Address: 9-10F,1stBldg.,No.81BeiqingRoad,Haidian District,Beijing,China E-mail: huanghu@baicells.com Tele: +86-13751023286 Date: 2020/08/25

Baicells Technologies Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for (FCC ID: 2AG32EG7010CM11N) To Whom It May Concern:

We, the undersigned, hereby authorize Mr. Zhang Shangwen from CCIC Southern Testing Co., Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by CCIC Southern Testing Co., Ltd. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Signature:

Name/title: Back Huang /Certification Manager Company: Baicells Technologies Co., Ltd. Address: 9-10F,1stBldg.,No.81BeiqingRoad,Haidian District,Beijing,China E-mail: huanghu@baicells.com Tele: 86-010-62607100 Date: 2020/08/25