FCC ID: 2AG32EG7035E LTE Outdoor CPE

Baicells EG7035E User Manual V100R001C00 01 All rights reserved Baicells Technologies Co., Ltd. About This Document This document introduces the specifications of Baicells EG7035E CPE and guides users to install and configure it. Copyright Notice Baicells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of Baicells. Disclaimer This specification is preliminary and is subject to change at any time without notice. Baicells assumes no responsibility for any errors contained herein. For more information, please consult our technical engineers. Revision Record Date Version Description 24 Jan,2017 V1.0 Initial released. Contact Us Baicells Technologies Co., Ltd.North America Address: 555 Republic Drive, Suite 200 Plano, TX 75074 E-mail: support_na@baicells.com Phone: +1-972-800-1157 Website: http://www.baicells.com/

Contents 1. Product Overview ....................................................................................................... 1 1.1 Introduction .............................................................................................................. 1 1.2 Features ..................................................................................................................... 1 1.3 Appearance ............................................................................................................... 1 2. Technical Specifications ............................................................................................... 5 2.1 Basic Specification .................................................................................................... 5 2.2 RF Specification ........................................................................................................ 5 2.3 SW Specification ....................................................................................................... 6 2.4 Device Management .................................................................................................. 6 2.5 Environment Specification ......................................................................................... 7 3. Installation Guide.......................................................................................................... 8 3.1 Support Materials ....................................................................................................... 8 3.2 Install USIM Card and Ethernet Cable ........................................................................ 8 3.3 Install on Pole ............................................................................................................. 9 3.4 Install on Wall ........................................................................................................... 10 3.5 Grounding ................................................................................................................. 10 3.6 Regulatory Compliance ............................................................................................ 11 4. Configuration Guide ................................................................................................... 13 4.1 Log in ........................................................................................................................ 13 4.2 View Status ............................................................................................................... 13 4.3 Basic Configuration .................................................................................................. 14 4.3.1 LTE Setting ........................................................................................................ 14 4.3.2 Set Connection Method .................................................................................... 14 4.3.3 Set Scan Mode .................................................................................................. 15 4.3.4 Lock Frequency (Earfcn) ................................................................................... 15 4.3.5 Lock PCI ............................................................................................................. 16 Appendix A FAQs ......................................................................................................... 18 Appendix B Shipping List ............................................................................................. 19 Figures Figure 1-1 EG7035E Appearance ................................................................................ 2 Figure 1-2 Interface and Button of EG7035E ............................................................... 2 Figure 1-3 LED Indicators of EG7035E ........................................................................ 3 Figure 3-1 Install Ethernet Cable and USIM Card ....................................................... 8 Figure 3-2 Connection Diagram ................................................................................... 9 Figure 3-3 Install the Bracket ....................................................................................... 9 Figure 3-4 Install on Pole ........................................................................................... 10 Figure 3-5 Install on Wall ............................................................................................ 10 Figure 3-6 Grounding ................................................................................................. 11 Figure 4-1 Login Page ................................................................................................ 13 Figure 4-2 View Status ............................................................................................... 14 Figure 4-3 Set Connection Method ............................................................................ 14 Figure 4-4 Set Scan Mode ......................................................................................... 15 Figure 4-5 Lock Frequency ........................................................................................ 16 Figure 4-6 Lock Frequency ........................................................................................ 17 Tables Table 1-1 Description of EG7035E Interface and Button ............................................. 2 Table 1-2 LED Indicator Description ............................................................................. 3 Table 2-1 Basic Specification ....................................................................................... 5 Table 2-2 RF Specification ........................................................................................... 5 Table 2-3 SW Specification .......................................................................................... 6 Table 2-4 Device Management ..................................................................................... 6 Table 2-5 Environment Specification ............................................................................ 7 Table 3-1 Support Materials for Installing ..................................................................... 8 1. Product Overview 1.1 Introduction Baicells is a high-tech company dedicated in wireless broadband access solutions and service operation. With the advent of the Internet+ era, the development of WBB is imminent. Through continuous innovation, Baicells launches the world first mobile broadband system based on the Internet architecture and unlicensed spectrum. Baicells can provide series CPEs, include indoor and outdoor unit on different spectrums. Baicells EG7035E is a high performance outdoor CPE. The EG7035E has the superior wireless access performance and comprehensive routing capabilities, which have the abilities to bring the end-users WBB services. 1.2 Features The EG7035E is designed according to the simplicity principle, which can evolve in a short period and realize fast customization, delivery and deployment as well. The main features of the EG7035E is as follows:

Support TD-LTE network according to the operators choice. LTE TDD 3650MHz ~ 3700MHz Support the 100Mbps Ethernet interface. Intuitionist and convenient Web-based management. Built-in LTE bipolar directional high gain antenna. Support TR069 and OMA-DM network management protocol. Support cell lock, SIM lock, and Pin lock. User-friendly design of LED indicator. Power supply with PoE. Support pole installation or wall mounting. 1.3 Appearance The EG7035E appearance is shown in Figure 1-1. 1 Figure 1-1 EG7035E Appearance The EG7035E interfaces and buttons are shown in Figure 1-2. Figure 1-2 Interface and Button of EG7035E The EG7035E interface and button description is given in Table 1-1. Table 1-1 Description of EG7035E Interface and Button Interface & Button Description PoE SD slot USIM Slot Connected to the PoE power adapter Support SD card Support 1.8V/3.0V USIM 2FF Restore Button Long press over 10 seconds to restore the factory settings 2 Interface & Button Description LED Indicator LTE signal strength Indicator& status indicator GND Connected to Earth by conductor The LED indicators are shown in Figure 1-3. Figure 1-3 LED Indicators of EG7035E The description of LED indicators are given in Table 1-2. Table 1-2 LED Indicator Description Identity Description Color Status Description MIU Yellow OFF Reserved.

-

Steady On Reserved. Blanking Reserved. LTE Network state OFF LTE disconnected. Indicator Blue Steady On LTE connected. SIM SIM card status Yellow Steady On The SIM card is normal. indicator Blanking The SIM card is abnormal or not inserted. LAN 100Mbps Eth Yellow OFF Ethernet connection does not Indication established. Steady On Ethernet connection is normal. Blanking Data is transmitting. PWR Power Indicator Yellow OFF No Power Supply Steady On Power On 3 Identity Description Color Status Description LTE Signal 5 LTEs, Indicate Green All OFF Signal is too weak to attach. connection state and signal strength Steady On According to signal strength in turn light up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 4 2. Technical Specifications 2.1 Basic Specification Item Description LTE Standard 3GPP Release 9 Table 2-1 Basic Specification Ethernet LAN Port One RJ-45 port 10/100 auto-sensing, auto-MDX, PoE LED Indicators Power/LET Signal/LAN Indicator USIM Support 1.8V/3V 2FF Restore Button Tact Button Long press over 10s to restore the factory settings Power Supply Dimension Input: Universal range 100V~240V AC About 248mm * 248mm * 80mm Weight Color About 1800g Pantone white C 2.2 RF Specification Item Mode Table 2-2 RF Specification Description TDD LTE Channel Bandwidth 5 MHz /10 MHz /15 MHz /20 MHz MAX Output Power LTE Standard Frequency Antenna Gain Mode Frequency 17dBm 3GPP R9 3650MHz~3700MHz 19.5 dBi Wi-Fi 2400MHz~2483.5MHz MAX Output Power Antenna Gain 15dBm 2dBi 5 2.3 SW Specification Table 2-3 SW Specification Item Description Language Settings English Network Mode Bridge / NAT SIM PIN Management SIM Lock Network Connection setup Create, delete, and edit APNs Set up dial-up connection automatically Set up dial-up connection manual LTE Scan Mode Full Band Cell Lock VPN NAT Statistics Band / Frequency Preferred Support VPN pass through Support PPTP tunnel mode Port forwarding Port trigger DMZ UPnP LAN Link Status Transmit / Receive traffic Running Time 2.4 Device Management Item Maintenance TR069 Port mirror Syslog Table 2-4 Device Management Description Date & Time setting Reset Restore factory settings Restore/Backup Configuration File Local upgrade FOTA upgrade Can enable or disable TR069 Management Can enable or disable the port mirror function Support the syslog function can send the log to the PC via LAN Diagnostics Support the Ping and trace route 6 2.5 Environment Specification Table 2-5 Environment Specification Item Description Operating Temperature Storage Temperature

-40 ~ 55

-40 ~ 70 Operating Humidity 5% ~ 95%

7 3. Installation Guide 3.1 Support Materials Before installation, prepare the following support materials accordingly, as given in Table 3-1. Table 3-1 Support Materials for Installing Item Description Ethernet cable Outdoor Shield CAT5E Shorter than 330 feet Ground wire 16mm yellow-green wire 3.2 Install USIM Card and Ethernet Cable 1. Screw the two screws on the waterproof cover. 2. Open the waterproof cover, and connect the Ethernet cable to the Ethernet interface. 3. Insert the USIM card to the USIM slot. Note following the directions. 4. Close the waterproof cover and tighten the two screws on the cover, as shown in Figure 3-1. Figure 3-1 Install Ethernet Cable and USIM Card 5. Connected Ethernet cable to the power adapter, as shown Figure 3-2. Pay attention to the power adapter interface directions. 8 Figure 3-2 Connection Diagram 6. Power on, the LED indicator will light up. 3.3 Install on Pole 1. Tighten the screws at the bottom of the bracketas shown in Figure 3-3. Figure 3-3 Install the Bracket 2. Install the bracket on pole as shown as Figure 3-4. 9 Figure 3-4 Install on Pole 3.4 Install on Wall Install bracket on wall as show as Figure 3-5. Figure 3-5 Install on Wall 3.5 Grounding The EG7035E must be grounding, please contact professional person to operation. 10 Using grounding cable, connect the grounding screw to the ground row, as shown in Figure 3-6. Figure 3-6 Grounding 3.6 Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning This equipment complies with FCC radiation exposure limits set forth for an 11 uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator & your body. ISEDC Compliance This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause in terference, and (2) This device must accept any interference, including interference t hat may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d' Innovation, Science et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 30cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. 12 4. Configuration Guide 4.1 Log in The EG7035E manages, configures, and maintains the device by web management page. The steps to log in are as follows:

1. In the address column of browser, type in http://192.168.150.1, then press Enter, login in page is shown in Figure 4-1. Figure 4-1 Login Page 2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 4.2 View Status In the overview area, you can view the device information and LTE status, such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown in Figure 4-2. 13 Figure 4-2 View Status 4.3 Basic Configuration 4.3.1 LTE Setting To set the LTE Network, perform the following steps:

1. Choose LTE. 2. In the LTE Setting area, configure the LTE network. 4.3.2 Set Connection Method To set the LTE network connection method, perform the following steps:

1. Choose LTE>connection Method, enter the setting connection method page, as shown in Figure 4-3. Figure 4-3 Set Connection Method 14 2. In the connection Method area, set the connection method 3. There are two methods to connect the LTE network, it is needed to choose a method between Auto and Manual, if you want to auto connect to the LET network you should choose the Auto, otherwise you should choose Manual. 4. Click SAVE & APPLY. 4.3.3 Set Scan Mode To set the LTE network scan mode, perform the following steps:

1. Choose LTE>Scan Method, enter the setting scan method page, as shown in Figure 4-4. Figure 4-4 Set Scan Mode 2. In the Scan Method area, set the scan mode 3. You can choose full Band, Frequency Lock, or PCI Lock. 4.3.4 Lock Frequency (Earfcn) To clock the frequency, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click Frequency Lock to lock the frequency. 3. Click ADD LIST, choose a band and frequency, and then click Add to add the band and frequency to the list, as shown in Figure 4-5. 15 Figure 4-5 Lock Frequency 4. Click SAVE & APPLY. 4.3.5 Lock PCI To lock the PCI, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click PCI Lock to lock the PCI. 3. Click ADD LIST you can choose a band, frequency and PCI, then click Add to add the frequency and PCI to the list, as shown in Figure 4-6. 16 Figure 4-6 Lock Frequency 4. Click SAVE & APPLY. 17 Appendix A FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Login to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings. After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings. 18 Appendix B Shipping List The product outward appearance, the color take the material object as, the picture only Amount 1 1 1 1 1 supply reference. Index Content Picture EG7035E CPE Power cord PoE adapter Mounting bracket 1 2 3 4 User Manual 5 19

Baicells Technologies Co., Ltd. Add: 3F, Hui Yuan Development Building, No.1 Shangdi Information Industry Base, Haidian Dist., Beijing China Tel: +86-010-62607100 Fax: +86-010-62607100 Email: huanghu@baicells.com FCC Authorization 2017-04-11 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We (Baicells Technologies Co., Ltd.), the undersigned, hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, This authorization is valid until further written notice from the applicant. 21 U.S.C. 862. Sincerely Yours, Signature:

Back Huang Certification Engineer QA-FR-170-B