FCC ID: 2AG32EG7035L96 LTE Outdoor CPE

Baicells EG7035L-M11 User Manual V100R001C00 02 All rights reserved Baicells Technologies Co., Ltd. About This Document This document introduces the specifications of BaicellsEG7035L-M11 CPE and guides users to install and configure it. Baicells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of Baicells. Copyright Notice Disclaimer This specification is preliminary and is subject to change at any time without notice. Baicellsassumes no responsibility for any errors contained herein. For more information, please consult our technical engineers. Disposal of Electronic and Electrical Waste Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with unsorted waste. Pleasecontact your local recycling authority for disposal of this product. Revision Record Date Version Description 5June,2017 V1.0 Initial released. Contact Us Baicells Technologies Co., Ltd.North America Address: 555 Republic Drive, Suite 200 Plano, TX 75074 E-mail: support_na@baicells.com Phone: +1-972-800-1157 Website: http://www.baicells.com/

Contents 1. Product Overview ......................................................................................................... 1 1.1 Introduction .......................................................................................................... 1 1.2 Features ................................................................................................................ 1 1.3 Appearance ........................................................................................................... 1 2. Technical Specifications ............................................................................................... 5 2.1 Basic Specification ................................................................................................ 5 2.2 RF Specification ..................................................................................................... 5 2.3 SW Specification ................................................................................................... 5 2.4 Device Management ............................................................................................... 6 2.5 Environment Specification ...................................................................................... 6 2.6 Regulatory Compliance ........................................................................................... 7 3. Installation Guide.......................................................................................................... 8 3.1 Support Materials ................................................................................................... 8 3.2 Install USIM Card and Cables .................................................................................. 8 3.3 Install on Wall ....................................................................................................... 10 3.4 Install onPole ........................................................................................................ 11 3.5 Grounding ............................................................................................................ 11 4. Configuration Guide ................................................................................................... 12 4.1 Log in .................................................................................................................... 12 4.2 View Status ........................................................................................................... 12 4.3 Basic Configuration ............................................................................................... 13 4.3.1 LTE Setting .................................................................................................... 13 4.3.2 Set Connection Method................................................................................. 13 4.3.3 Set Scan Mode .............................................................................................. 14 4.3.4 Lock Frequency (Earfcn) ................................................................................ 14 4.3.5 LockPCI.......................................................................................................... 15 4.3.6 SAS Settings .................................................................................................. 16 Appendix A Appendix B FAQs ......................................................................................................... 17 Shipping List ............................................................................................. 18 Figures Figure 1-1 EG7035L-M11 Appearance......................................................................... 2 Figure 1-2 Interface and Button of EG7035L-M11 ....................................................... 2 Figure 1-3 LED Indicators of EG7035L-M11 ................................................................ 3 Figure 4-1 Login Page ................................................................................................ 12 Figure 4-2 View Status ............................................................................................... 13 Figure 4-3 Set Connection Method ............................................................................ 13 Figure 4-4 Set Scan Mode ......................................................................................... 14 Figure 4-5 Lock Frequency ........................................................................................ 15 Figure 4-6 Lock Frequency ........................................................................................ 16 Tables Table 1-1 Description of EG7035L-M11 Interface and Button ..................................... 2 Table 1-2 LED Indicator Description ............................................................................. 3 Table 2-1 Basic Specification ....................................................................................... 5 Table 2-2 RF Specification ........................................................................................... 5 Table 2-3 SW Specification .......................................................................................... 5 Table 2-4 Device Management ..................................................................................... 6 Table 2-5 Environment Specification ............................................................................ 6 Table 3-1 Support Materials for Installing ..................................................................... 8 1. Product Overview 1.1 Introduction Baicells is a high-tech company dedicated in wireless broadband access solutions and service operation. With the advent of the Internet+ era, the development of WBB is imminent. Through continuous innovation, Baicells launches the world first mobile broadband system based on the Internet architecture and unlicensed spectrum. Baicells can provide series CPEs, include indoor and outdoor unit on different spectrums. BaicellsEG7035L-M11 is high performance outdoor CPE. The EG7035L-M11 has the superior wireless access performance and comprehensive routing capabilities, which have the abilities to bring the end-users WBB services. 1.2 Features The EG7035L-M11 is designed according to the simplicity principle, which can evolve in a short period and realize fast customization, delivery and deployment as well. The main features of the EG7035L-M11 is as follows:

Support TD-LTE network according to the operators choice. LTE comply with 3GPP Release9 CAT4. LTE TDD band48. Support the 100Mbps Ethernet interface. Intuitionist and convenient Web-based management. Built-in LTE bipolar directional high gain antenna. Support TR069 and OMA-DM network management protocol. Support cell lock, SIM lock, and Pin lock. User-friendly design of LED indicator. Power supply with PoE. Support pole installation or wall mounting. 1.3 Appearance The EG7035L-M11 appearance is shown in Figure 1-1. 1 Figure 1-1EG7035L-M11 Appearance The EG7035L-M11 interfaces and buttons are shown in Figure 1-2. Figure 1-2Interface and Button of EG7035L-M11 The EG7035L-M11 interface and button description is given in Table 1-1. Table 1-1 Description of EG7035L-M11 Interface and Button Interface & Button Description PoE TF SIM RESET GND Connected to the PoEpower adapter Support SD card Support 1.8V/3.0V USIM 2FF Long press over 10 seconds to restore the factory settings Connected to Earth by conductor The LED indicators are shown in Figure 1-3. 2 MIU LTE SIM Figure 1-3 LED Indicators of EG7035L-M11 The description of LED indicators are given in Table 1-2. Table 1-2 LED Indicator Description Identity Description Color Status Description Yellow OFF Reserved.

Steady On Reserved. Blanking Reserved. Network state Indicator Blue OFF LTE disconnected. Steady On LTE connected. SIM card status indicator Yellow Steady On The SIM card is normal. Blanking The SIM card is abnormal or not inserted. LAN Yellow OFF 100Mbps Eth Indication Ethernet connection does not established. Steady On Ethernet connection is normal. Blanking Data is transmitting. PWR Power Indicator Yellow OFF No Power Supply Steady On Power On LTE Signal 5 LTEs, Indicate Green All OFF Signal is too weak to attach. 3 Identity Description Color Status Description connection state and signal strength Steady On According to signal strength in turn light up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 4 2. Technical Specifications 2.1 Basic Specification LED Indicators Power/LET Signal/LAN Indicator Item LTE Standard Ethernet LAN Port USIM Restore Button Power Supply Dimension Weight Color Table 2-1 Basic Specification Description 3GPP Release 9 One RJ-45 port 10/100 auto-sensing, auto-MDX, PoE Support 1.8V/3V 2FF Tact Button Long press over 10s to restore the factory settings Input: Universal range 100V~240V AC About 241mm * 154mm * 50mm About 900g Pantone white C 2.2 RF Specification Item LTE Mode Channel Bandwidth MAX Output Power LTE Standard LTE Band Max Antenna Gain Table 2-2 RF Specification Description TDD LTE 5 MHz /10 MHz /15 MHz /20 MHz 232dBm 3GPP R9 Band48 14dBi 2.3 SW Specification Item Table 2-3SW Specification Description Language Settings English Network Mode Bridge / NAT SIM PIN Management 5 Item Description SIM Lock Network Connection setup Create, delete, and edit APNs Set up dial-up connection automatically Set up dial-up connection manual 2.4 Device Management Full Band Cell Lock Band / Frequency Preferred Support VPN pass through Support PPTP tunnel mode Port forwarding Port trigger DMZ UPnP LAN Link Status Transmit / Receive traffic Running Time Table 2-4Device Management Description Date & Time setting Reset Restore factory settings Restore/Backup Configuration File Local upgrade FOTA upgrade Can enable or disable TR069 Management Can enable or disable the port mirror function Support the syslog function can send the log to the PC via LAN LTE Scan Mode VPN NAT Statistics Item Maintenance TR069 Port mirror Syslog Diagnostics Support the Ping and trace route 2.5 Environment Specification Item Description Table 2-5Environment Specification 6 Item Description Operating Temperature Storage Temperature

-40 ~ 55

-40 ~ 70 Operating Humidity 5% ~ 95%

2.6 Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator & your body. 7 3. Installation Guide 3.1 Support Materials Before installation, prepare the following support materialsaccordingly, asgiven in Table 3-1. Item Ethernet cable Table 3-1Support Materials for Installing Description Outdoor Shield CAT5E Shorter than 330 feet Ground wire 16mm yellow-green wire 3.2 Install USIM Card and Cables 1. Screw the screw on the waterproof cover, and open the waterproof cover. 2. Insert the USIM card to the USIM slot. Note following the directions. ground screw. 3. Connect the Ethernet cable to the POE port, and connect the ground cable to the 8 4. Close the waterproof cover and fasten the screw on the cover. 5. Connected Ethernet cable to the power adapter. Pay attention to the power adapter interface directions. 6. Power on, the LED indicator will light up. 9 3.3 Install on Wall 1. Slipping the bracket from the CPE. 2. Fit the CPE on the wall, and mark the drilling locations. 3. Drill four 10mm diameter and 70mm depth holes in the wall by following the marked locations. M5tapping screws. 4. Check the up/down direction of the bracket, and then fix it on wall using 5. Install the CPE to the bracket and fasten the screw. 10 3.4 Install onPole 1. Round an anti-slip rubber on the pole. 2. Fix the bracket using the hoop. 3. Install the CPE to the bracket and fasten the screw. 3.5 Grounding The EG7035L-M11 must begrounding, please contact professional person to operation. Using grounding cable, connect the grounding cable to the ground row. 11 4. Configuration Guide 4.1 Log in The EG7035L-M11 manages, configures, and maintains the device by web management page.The steps to log in are as follows:

1. In the address column of browser, type in http://192.168.150.1, then press Enter, login in page is shown in Figure 4-1. Figure 4-1 Login Page 2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 4.2 View Status In the overview area, you can view the device information and LTE status,such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown in Figure 4-2. 12 Figure 4-2 View Status 4.3 Basic Configuration 4.3.1 LTE Setting To set the LTE Network, perform the following steps:

1. Choose LTE. 2. In the LTE Setting area, configure the LTE network. 4.3.2 Set Connection Method To set the LTE network connection method, perform the following steps:

1. Choose LTE>connection Method, enter the setting connection method page, as shown in Figure 4-3. Figure 4-3 Set Connection Method 13 2. In the connection Method area, set the connection method 3. There are two methods to connect the LTE network, it is needed to choose a method between Auto and Manual, if you want to auto connect to the LET network you should choose the Auto, otherwise you should choose Manual. 4. Click SAVE & APPLY. 4.3.3 Set Scan Mode 4-4. Figure 4-4 Set Scan Mode To set the LTE network scan mode, perform the following steps:

1. Choose LTE>Scan Method, enter the setting scan method page, as shown in Figure 2. In the Scan Method area, set the scan mode 3. You can choose full Band, Frequency Lock, or PCI Lock. 4.3.4 Lock Frequency (Earfcn) To clock the frequency, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click Frequency Lock to lock the frequency. 3. Click ADD LIST, choose a band and frequency, and then click Add to add the band and frequency to the list, as shown in Figure 4-5. 14 Figure 4-5 Lock Frequency 4. Click SAVE & APPLY. 4.3.5 LockPCI To lock the PCI, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click PCI Lock to lock the PCI. 3. Click ADD LIST you can choose a band, frequency and PCI, then click Add to add the frequency and PCI to the list, as shown in Figure 4-6. 15 Figure 4-6 Lock Frequency 4. Click SAVE & APPLY. 4.3.6 SAS Settings 16 Appendix A FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Login to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings. After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings. 17 1 2 3 4 Appendix B Shipping List The product outward appearance, the color take the material object as, the picture only supply reference. Index Content Picture Amount 1 EG7035L-M11 CPE with Simple Mounting bracket Power cord PoEadapter User Manual 1 1 1 18

Baicells Model:EG7035L-M11 Power Rating: == 24V;0.5A UA AANA AA SN:1203000002Y YMDPXXXX Bands: 48 AK ie UAT AT FCC ID: 2AG32EG7035L96 IME OO TOG UUM A LAN MAC:XXXXXXXXXXXX

< 25mm Baicells Technologies Co.,Ltd. 6mm AS Sse CALI E UL II ll a SN CS Ca 9 ov OS 09 0 08 0600} oF oz of ov OS 09 OL oF DBM w & WE WL TATTOO ATTA ATTUATTUVATTTUATIUGTINVCHTULCCNYA LUNN \ A \

TTKN\N NN \\\

Baicells Technologies Co., Ltd. Date: Jun. 04, 2020 File Name Schematics.pdf Block Diagram.pdf Operational Description.pdf Part List.pdf Tune-up Procedure.pdf Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AG32EG7035L96 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Schematics Block Diagram Operational Description Part List Tune-up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang/ Manager Typed name and Title

Baicells Technologies Co., Ltd. Date: 6/11/2020 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD To Whom It May Concern:

We, Baicells Technologies Co., Ltd., state that our device, FCC ID: 2AG32EG7035L96, has a non-removable rear cover. The label will be placed on the rear cover. And the label will be visible to the end users when they purchase the product. The back cover can not be moved away, so the FCC ID label has to be placed on the surface of product. Sincerely, Signature

[Back Huang (Name)]

[Manager (Title)]

[Baicells Technologies Co., Ltd. (Company name)]

Baicells Technologies Co., Ltd. Date: 6/11/2020 Subject: authorization for adding family models To whom it May concern, Statement We would like to confirm the product LTE Outdoor CPE with models EG7035L-M11, EG7035L-M2 are same in all respects. Only the model names are different for different market requirement. Yours sincerely,

[signature]

[Back Huang]

[Manager]

[Baicells Technologies Co., Ltd.]

Baicells Technologies Co., Ltd. FCC ID: 2AG32EG7035L96 POWER OF ATTORNEY Date: Jun. 04, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd.

(Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Jun. 03, 2021. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Baicells Technologies Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang / Manager Typed name and Title

Baicells Technologies Co., Ltd. Date: 2020-06-04 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AG32EG7035L96 To Whom It May Concern:

Sincerely, Signature

[Back Huang]

[Manager]

[Baicells Technologies Co., Ltd.]

This letter is to statement that EG7035L-M11, EG7035L-M2 / LTE Outdoor CPE. has been tested according to FCC Part 15B by Waltek Services (Shenzhen) Co., Ltd. (Test Report No.:

WTS20S02005771E). And the SDOC file, meetting the requirements of the FCC regulations, would been provided when the device is sold by the responsible party in US. The service will not be sold until the SDOC is provided. If the sale does not have an SDOC, all responsibility is the responsibility of the applicant.