FCC ID: 2AG32EG8013LM11 LTE Outdoor CPE

 

ATOM OD06 CPE

Installation &

Configuration Guide

Model EG8013L-M11

April 2020

Version 1.2

1

This document is for operators who will be installing and configuring the Baicells ATOM OD06 CPEs, model EG8013L

This document version is based on the firmware version BaiCE_BG_1.6.11.

All technical specifications and documents are on the Baicells website under Resources > Documentation.

About This Document

Related Documents

 Baicells SNAP PoE+ Router Data Sheet

 Baicells SNAP PoE+ Router User Manual

 Baicells ATOM OD06H/L Data Sheet

Copyright Notice

Baicells Technologies, Inc., copyrights the information in this document. No part of this document may be reproduced

in any form or means without the prior written consent of Baicells Technologies, Inc. The Baicells logo is a proprietary

trademark of Baicells Technologies, Inc. Other trademarks mentioned in this document belong to their owners.

Description

SMEs/Contributors

Author/Editor

-

Tang Houcheng

Revision Record

Date

18-Aug-2020

Version

v1.0

Draft

Support Resources

Contact Us

 Documentation - Baicells product data sheets, this document, and other technical manuals may be found at

Baicells > Resources > Documentation.



Support - Open a support ticket, process an RMA, and the Support Forum are at Baicells > Support.

Baicells Technologies Co., Ltd.

Baicells Technologies North America, Inc.

China

North America

Address:

9-10F,1stBldg.,No.81BeiqingRoad,Haidian

District,Beijing,China

555 Republic Dr., #200, Plano, TX 75074, USA

Phone:

+86-10-62607100

+1-888-502-5585

Email:

contact@Baicells.com

sales_na@Baicells.com or support_na@Baicells.com36T

Website: www.Baicells.com

https://na.Baicells.com

2

Table of Contents

List of Figures ..................................................................................................................................................................... 4

List of Tables ....................................................................................................................................................................... 6

Introduction .............................................................................................................................................................. 7

1.

Description ............................................................................................................................................................ 7

1.1.

ODU Modes........................................................................................................................................................... 7

1.2.

Features ................................................................................................................................................................ 9

1.3.

Installation ................................................................................................................................................................. 9

2.

Part & Materials .................................................................................................................................................... 9

2.1.

Dimensions ......................................................................................................................................................... 10

2.2.

LEDs & Interfaces ................................................................................................................................................ 10

2.3.

Preparing to Install .............................................................................................................................................. 11

2.4.

Installation .......................................................................................................................................................... 11

2.5.

Installation with Baicells SNAP Router ................................................................................................................ 15

2.6.

Configuration ........................................................................................................................................................... 16

3.

Computer Requirements..................................................................................................................................... 16

3.1.

CPE Software ....................................................................................................................................................... 16

3.2.

Login.................................................................................................................................................................... 16

3.3.

Status Menu ........................................................................................................................................................ 17

3.4.

3.4.1.

Overview ........................................................................................................................................................ 17

Network Menu .................................................................................................................................................... 21

3.5.

LAN Settings.................................................................................................................................................... 21

3.5.1.

3.5.2. WAN Settings ...................................................................................................................................................... 22

3.5.2.1. NAT Mode ....................................................................................................................................................... 22

Router Mode .................................................................................................................................................. 22

3.5.2.2.

Tunnel Mode .................................................................................................................................................. 22

3.5.2.3.

3.5.2.4.

Bridge Mode ................................................................................................................................................... 23

3.5.2.5. Mixed Mode ................................................................................................................................................... 23

Static Routes ................................................................................................................................................... 24

3.5.3.

DMZ ................................................................................................................................................................ 25

3.5.4.

3.5.5.

UPnP ............................................................................................................................................................... 25

LTE Menu ............................................................................................................................................................ 26

3.6.

Connection Settings ........................................................................................................................................ 26

3.6.1.

3.6.1.1.

Roaming setting .............................................................................................................................................. 26

3.6.1.2. Default connection ......................................................................................................................................... 26

Power Scan Option ......................................................................................................................................... 26

3.6.1.3.

Edit APN Profile .............................................................................................................................................. 27

3.6.2.

PIN Management ............................................................................................................................................ 27

3.6.3.

Cell selection .................................................................................................................................................. 28

3.6.4.

SIM Lock Settings ............................................................................................................................................ 30

3.6.5.

MTU ................................................................................................................................................................ 30

3.6.6.

Security Menu ..................................................................................................................................................... 31

3.7.

IP Filtering ....................................................................................................................................................... 31

3.7.1.

IPv6 Filtering ................................................................................................................................................... 31

3.7.2.

MAC Filtering .................................................................................................................................................. 32

3.7.3.

URL Filtering ................................................................................................................................................... 33

3.7.4.

3

System Security .............................................................................................................................................. 33

3.7.5.

Connect Limit.................................................................................................................................................. 34

3.7.6.

Schedule ......................................................................................................................................................... 34

3.7.7.

NAT Menu ........................................................................................................................................................... 35

3.8.

Port Forwarding .............................................................................................................................................. 35

3.8.1.

Port Triggering ................................................................................................................................................ 36

3.8.2.

ALG ................................................................................................................................................................. 37

3.8.3.

System Menu ...................................................................................................................................................... 37

3.9.

3.9.1.

Account ........................................................................................................................................................... 37

3.9.2. WEB Settings ....................................................................................................................................................... 37

NTP ................................................................................................................................................................. 38

3.9.3.

3.9.4. TR-069 ................................................................................................................................................................. 38

3.9.5. TR-069 Certificate ............................................................................................................................................... 39

Restore / Update ............................................................................................................................................ 39

3.9.6.

Firmware Update ............................................................................................................................................ 39

3.9.6.1.

Restore Factory Settings ................................................................................................................................. 39

3.9.6.2.

Diagnosis ........................................................................................................................................................ 40

3.9.7.

TCPDump ........................................................................................................................................................ 40

3.9.7.1.

Ping ................................................................................................................................................................. 40

3.9.7.2.

Trace ............................................................................................................................................................... 41

3.9.7.3.

Result .............................................................................................................................................................. 41

3.9.7.4.

Backup Settings .............................................................................................................................................. 41

3.9.8.

System Log ...................................................................................................................................................... 42

3.9.9.

System Messages ............................................................................................................................................ 42

3.9.10.

3.9.11.

SAS Settings .................................................................................................................................................... 43

3.10. Reboot ................................................................................................................................................................ 44

Logout ................................................................................................................................................................. 44

3.11.

Appendix: Regulatory Compliance ................................................................................................................................... 45

FCC Compliance ............................................................................................................................................................... 45

List of Figures

FIGURE 1: LTE NETWORK ARCHITECTURE .................................................................................................................................... 7

FIGURE 2: DIMENSIONS ......................................................................................................................................................... 10

FIGURE 3: LOW-GAIN LEDS & INTERFACES ................................................................................................................................ 10

FIGURE 5: LTE NETWORK ARCHITECTURE .................................................................................................................................. 12

FIGURE 6: POE ADAPTOR ....................................................................................................................................................... 12

FIGURE 7: LOW GAIN CPE GROUNDING .................................................................................................................................... 12

FIGURE 9: POWER ADAPTOR ................................................................................................................................................... 13

FIGURE 10: RUBBER BAND ..................................................................................................................................................... 13

FIGURE 11: BRACKET ............................................................................................................................................................. 13

FIGURE 12: ATTACH UE ......................................................................................................................................................... 14

FIGURE 16: MARK HOLES FOR DRILLING ................................................................................................................................... 14

FIGURE 17: FIX BRACKET TO WALL ........................................................................................................................................... 14

FIGURE 18: ATTACH UE ......................................................................................................................................................... 14

FIGURE 21: LOGIN ................................................................................................................................................................ 17

FIGURE 22: STATUS ............................................................................................................................................................... 18

4

FIGURE 23: THROUGHPUT STATISTICS ....................................................................................................................................... 18

FIGURE 24: INTERNET STATISTICS ............................................................................................................................................. 18

FIGURE 25: LAN STATUS ........................................................................................................................................................ 19

FIGURE 26: DEVICE LIST ......................................................................................................................................................... 19

FIGURE 27: DHCP SETTINGS .................................................................................................................................................. 21

FIGURE 28: DHCP STATIC LEASES ............................................................................................................................................ 21

FIGURE 29: WAN SETTINGS ................................................................................................................................................... 22

FIGURE 30: ROUTER MODE .................................................................................................................................................... 22

FIGURE 31: TUNNEL MODE .................................................................................................................................................... 23

FIGURE 32: BRIDGE MODE ..................................................................................................................................................... 23

FIGURE 33: MIXED MODE ...................................................................................................................................................... 24

FIGURE 35: STATIC ROUTES ..................................................................................................................................................... 24

FIGURE 36: DMZ ................................................................................................................................................................. 25

FIGURE 37: DMZ SETTINGS.................................................................................................................................................... 25

FIGURE 38: UPNP SETTINGS................................................................................................................................................... 25

FIGURE 39: CONNECTION SETTINGS ......................................................................................................................................... 26

FIGURE 40: DEFAULT CONNECTION SETTINGS ............................................................................................................................. 26

FIGURE 41: SCAN MODE SETTINGS ........................................................................................................................................... 27

FIGURE 42: APN PROFILES ..................................................................................................................................................... 27

FIGURE 43: PIN MANAGEMENT .............................................................................................................................................. 28

FIGURE 44: CELL SELECTIONS .................................................................................................................................................. 28

FIGURE 45: DEDICATED EARFCN ............................................................................................................................................ 29

FIGURE 46: CELL LOCK ........................................................................................................................................................... 29

FIGURE 47: PCI ONLY LOCK .................................................................................................................................................... 30

FIGURE 48: THROUGHPUT STATISTICS ....................................................................................................................................... 30

FIGURE 49: MTU SETTINGS ................................................................................................................................................... 30

FIGURE 50: FIREWALL BASIC SETTINGS...................................................................................................................................... 31

FIGURE 51: IP / PORT FILTERING ............................................................................................................................................. 31

FIGURE 52: IPV6 FILTERING .................................................................................................................................................... 32

FIGURE 53: MAC FILTERING ................................................................................................................................................... 32

FIGURE 54: URL FILTERING .................................................................................................................................................... 33

FIGURE 55: SYSTEM SECURITY ................................................................................................................................................. 33

FIGURE 56: CONNECT LIMIT ................................................................................................................................................... 34

FIGURE 57: SCHEDULE LIST ..................................................................................................................................................... 34

FIGURE 58: SCHEDULE SETTINGS ............................................................................................................................................. 35

FIGURE 59: PORT FORWARDING SETTINGS ................................................................................................................................. 36

FIGURE 60: PORT TRIGGERING SETTINGS................................................................................................................................... 36

FIGURE 61: THROUGHPUT STATISTICS ....................................................................................................................................... 37

FIGURE 62: ACCOUNT ........................................................................................................................................................... 37

FIGURE 63: WEB SETTINGS .................................................................................................................................................... 37

FIGURE 64: NTP SETTINGS ..................................................................................................................................................... 38

FIGURE 65: THROUGHPUT STATISTICS ....................................................................................................................................... 38

FIGURE 66: TR-069 CERTIFICATE ............................................................................................................................................ 39

FIGURE 67: RESTORE & UPDATE .............................................................................................................................................. 39

FIGURE 68: TCPDUMP SETTINGS ............................................................................................................................................ 40

FIGURE 69: PING DIAGNOSIS SETTINGS ..................................................................................................................................... 40

FIGURE 70: TRACE DIAGNOSIS SETTINGS ................................................................................................................................... 41

FIGURE 71: DIAGNOSIS RESULTS .............................................................................................................................................. 41

5

FIGURE 72: BACKUP SETTINGS ................................................................................................................................................ 41

FIGURE 73: SYSTEM LOG ........................................................................................................................................................ 42

FIGURE 74: SYSTEM LOGS ....................................................................................................................................................... 42

FIGURE 75: SYSTEM MESSAGE SETTINGS ................................................................................................................................... 42

FIGURE 76: SYSTEM MESSAGES ............................................................................................................................................... 43

FIGURE 77: REBOOT .............................................................................................................................................................. 44

FIGURE 78: THROUGHPUT STATISTICS ....................................................................................................................................... 44

List of Tables

TABLE 1: PARTS ...................................................................................................................................................................... 9

TABLE 2: MATERIALS ............................................................................................................................................................. 10

TABLE 3: INSTALLATION PROCEDURE ......................................................................................................................................... 15

TABLE 4: COMPUTER REQUIREMENTS ....................................................................................................................................... 16

TABLE 5: STATUS ................................................................................................................................................................... 19

TABLE 7: PORT FORWARDING .................................................................................................................................................. 36

6

1.

Introduction

1.1. Description

The Baicells Atom OD0406 Outdoor Low-Gain and Outdoor High-Gain User Equipment (UE) is part of a

broadband wireless access system that integrates with Long-Term Evolution (LTE) backhaul networks to

provide subscribers with Internet access. The UE, also referred to as Customer Premise Equipment (CPE),

communicates through a wireless connection to the operator’s eNodeB’s (eNB) at cell sites located in the

region. The eNBs communicate with the backhaul network (Figure 1).

Figure 2: LTE Network Architecture

The outdoor low-gain or high-gain UE may be selected because of the distance between the user's location

and the closest eNB or for environments where there may be blockage or partial blockage in the wireless

signal path between the UE and eNBs in the area - e.g., dense trees or buildings.

As an LTE standards-based product, the Baicells equipment provides higher near-line-of-sight (nLOS) and

non-line-of-sight (NLOS) signal penetration than other wireless technologies. The high-gain UE has a higher

antenna gain than the low-gain UE, making it possible to get the strongest possible signal reception for

subscribers.

The LTE standards organization that defines certain characteristics of user equipment across manufacturers

labels each progression of the standards as releases, such as Release 9, Release 10, etc., and categories,

such as Category 4 (CAT4) and Category 6/7 (CAT6/7).

Typically the difference from one release/category to the next is in capacity, i.e., higher throughput. There

is no physical difference between the CAT4 and CAT6/7 UE, but the low-gain UE and the high-gain UE do

look different from one another. A physical comparison is provided in section 4.

1.2. ODU Modes

This device can work at two modes, ODU standalone or IDU+ODU mode.

(1) ODU standalone Mode

Standalone mode, ODU can worked at NAT/TUNNEL/BRIDGE mode

7

a) NAT Mode, the ODU work as a LTE and Ethernet Gateway, it converts LTE network data to local

Ethernet data.

b) Tunnel Mode, the ODU can build a L2 or L3 VPN tunnel with a designated VPN server.

c) Bridge Mode, the ODU can bridge it LTE IP address to LAN port devices, when configured as the

bridge, the CPE’s LAN port will work as trunk mode, so it can’t assign IP address to any no-trunk

devices (like PC), so you have to Manual Configure the PC’s IP address in the same broadcast

domain (e.g. 192.168.150.88).

(2) IDU+ODU Mode

When the ODU connect to a IDU device (Baicells PoE router), it will automatic be configured as Bridge

mode, and assign all its LTE IP to IDU, at that mode, the IDU will take the place of ODU to control all the CPE

functions.

Before contacting Baicells FAE or your distributor, please DO NOT mixed use the two

modes.

CAUTION:

8

1.3. Features

The Baicells Atom UEs provide robust throughput and are designed for growth and expansion as

technology evolves. Some of the key features and attributes of the Atom outdoor UEs are listed below.

Exact specifications vary by model. For the latest information, please refer to the Baicells website for your

specific UE model.

 Standardized LTE TDD bands 42, 43, 48. Customization may be requested.

 Complies with 3GPP Release 10 (CAT6/7)

 1000 Mbps Ethernet interface (CAT6/7)

 Built-in bipolar directional LTE antenna

 Power supply using Power Over Ethernet (PoE)

 Cell lock, SIM lock, and Pin lock

 Pole or wall mount options

 TR-069 management protocol support



Local and remote GUI management

2.

Installation

2.1. Part & Materials

Table 1: Parts

Item

Atom

OD06L-EG8013L-M11

CPE

Qty

1

Power Cable

1

PoE Power Adaptor

1

Refer to Table 1 for a list of the components that you should receive with the Baicells outdoor UE.

Picture

You will need standard tools, Ethernet cable, ground wire, and RJ-45 connectors for installing and

connecting the outdoor unit (Table 2).

9

Table 2: Materials

Item

Description

Ethernet Cable

Ground Wire

Outdoor shield CAT5E, shorter than 330 feet

16mm2 yellow-green wire

2.2. Dimensions

The Baicells Atom outdoor low-gain and high-gain models of user equipment are powerful, standards-based

devices designed to connect seamlessly to any standard LTE eNB operating on the same frequency band.

The devices have a small, sleek form factor (Figure 3), yet are ruggedized for the most challenging outdoor

environments.

Figure 4: Dimensions

All models of the low-gain and high-gain UEs have external LED status indicator lights and interface

connectors (Figure 3). These external features make it easier to determine the UE's operational status and

to check cables.

2.3. LEDs & Interfaces

On the low-gain UE the LEDs are on the side of the unit, and the connection interfaces are on the bottom of

the unit. On the high-gain UE both the LEDs and the interfaces are on the side of the unit. Refer to Table 3

for a description of the LEDs and Table 4 for a description of the interfaces.

Figure 5: Low-Gain LEDs & Interfaces

10

Table 3: LEDs

LEDs vary by model – not all models will have all of the LEDs listed below.

Identity

Description

Color

Description

MIU

-

Yellow

Steady On

Reserved for future use

Reserved for future use

Status

Off

LTE

LTE network status

Blue

Blinking

Reserved. for future use

Off

The UE is not connected to the network

Steady On

The UE is connected to the LTE network

Steady On

The USIM card is functioning normally

SIM/USIM

SIM/USIM card status

Yellow

The USIM card is not inserted or is not

Blinking

functioning normally

100 or 1000 Mbps Local

Off

No Ethernet connection established

LAN

Area Network

Yellow

Steady On

Ethernet connection is normal

Ethernet status

PWR

Power status

Yellow

Blinking

Data is transmitting

Off

No power supply to the UE

Steady On

Power to the UE is on

LTE Signal

more bars, the stronger

Green

1, 2, 3, 4, or 5 bars to

indicate wireless

connection status. The

the signal between the

UE and a network cell

(eNB).

The signal is too weak for the UE to connect to

All Off

the network

Steady On

strength

Bars will light steadily according to signal

The UE is scanning the network

Blinking

The UE is authenticating with the network

The UE is getting an IP address from the

network

Table 4: Interfaces

Interfaces

PoE

TF or SD Slot

SIM/USIM Slot

RESET

GND

Interfaces vary by model – not all models will have all of the interfaces listed below.

Description

Power over Ethernet (PoE) power adaptor

Card slot for a secure digital (SD) card

Universal Subscriber Identity Module card slot, 1.8V/3.0V USIM 2FF

Reset/restore button

Ground lug. The unit is connected to Earth by conductor.

2.4. Preparing to Install

To help ensure a smooth and successful installation, check that you have all of the parts, materials, and

tools you will need, per section 2.1 Parts & Materials. When selecting the best outdoor location for the

installation, plan on placing the UE so that it faces the nearest eNB. You may need to adjust the tilt and

angle for optimum signal reception.

2.5. Installation

1. Loosen the screws on the UE's waterproof cover, and open the cover.

11

2.

Insert the service provider's SIM/USIM card into the card slot (Figure 6).

Attention: Never power on the unit while installing or uninstalling the USIM card. Doing so

could damage the card and the unit.

Figure 7: LTE Network Architecture

3. Prepare the outdoor shielded CAT5E Ethernet cable. The Ethernet cable will run between the

outdoor UE and the inside of the facility, where it will connect to the PoE adaptor and LAN. Cable

length will vary by location.

4. Connect one end of the Ethernet cable to the PoE port on the unit. Connect the other end to the

power adaptor (Figure 8).

Figure 9: PoE Adaptor

5. Close the UE’s waterproof cover, and tighten the screws.

6. Prepare the 16mm2 yellow-green ground wire, and follow the steps below. Once the unit is fully

installed, make sure the grounding cable is connected to a solid grounding point (earth).

a. Atom Low-Gain UE: Connect the ground cable to the ground screw (Figure 10).

Figure 11: Low gain CPE Grounding

12



13

b. Atom High-Gain UE: Connect the ground cable to the grounding screw in the ground row

(Figure 6). The figure is showing the UE mounted on a pole; mounting is covered in step 8.

7. Plug the power adaptor into an electrical outlet (Figure 12). Pay attention to the power adaptor

interface directions noted on the adaptor itself. The LED indicators should light up when the unit is

powered on.

Figure 13: Power Adaptor

8. Mount the UE: If you are installing the UE on a pole, e.g., to attach to a roof, go to step 9. If you are

installing the UE on an outside wall, go to step 10.

9. Pole installation:

a. Low-Gain UE:

Figure 15: Rubber Band

a1) Attach a heavy-duty anti-slip rubber band on the pole (Figure 14).

a2) Fix the UE bracket over the band using the hoop (Figure 16).

Figure 17: Bracket

a3) Attach the UE to the bracket, and tighten the screw (Figure 18).

Figure 19: Attach UE

a4) The UE is now ready for installation at its final outside location. Then, proceed to section 7

a1) Slip the bracket off of the Atom unit, and fit it on the wall to mark the drilling locations

(Figure 11), The marked locations, drill four 10-mm diameter and 70-mm depth holes.

Figure 20: Mark Holes for Drilling

Basic Configuration.

10. Wall installation:

a.

Low-Gain UE:

screws (Figure 12).

Figure 21: Fix Bracket to Wall

a2) Check the up/down direction of the bracket, and then fix it on the wall using the M5 tapping

a3) Attach the UE to the bracket, and tighten the screw (Figure13).

Figure 22: Attach UE

14

a4) Proceed to section 7 Basic Configuration.

2.6. Installation with Baicells SNAP Router

To explain the installation, the procedure in Table 3 uses a Baicells Atom OD04L Outdoor Low-Gain CPE as

the example. Refer to the CPE user manual on the Baicells website to complete some steps as indicated.

Table 4: Installation Procedure

1. With the CPE powered OFF, loosen the screws on the

3. Using the Ethernet cable, connect the CPE PoE port

waterproof cover and lift to access the interfaces.

and the router WAN port.

2. Insert the SIM card into the SIM slot.

Attention: Never power on the CPE while

installing or uninstalling the SIM card. Doing so could

damage the card and the unit.

Caution: Do not connect unsupported devices to

the router WAN port, as it may cause damage.

Per the associated steps in the CPE user manual

installation procedure:

4. Prepare the ground wire and connect one end of it to

the CPE ground terminal and the other end to a

reliable grounding point (earth).

5. Close the CPE's waterproof cover, and tighten the

screws.

6. Mount the CPE at its outdoor location, assuring proper

alignment to the nearest eNB tower.

7. Power the CPE ON, and check the satus of the LEDs to

ensure it is operating as expected.

8. Connect the router's power adapter to the power

connector on the back of the unit, and the other

end to a power outlet.

9. Turn power to the router ON.

10. Check the LED indicators to verify normal

operating status per Table 2 in section 2.2 of this

guide.

15



NOTE: If either the CPE or the router is not running the correct firmware, the router's LTE signal LED

will be OFF. Check for the latest firmware on the Baicells website, or contact Baicells support.

The setup is complete and ready to work. To configure features using the CPE GUI, go to the next section.

3. Configuration

3.1. Computer Requirements

The computer you use to connect with the CPE GUI must meet the requirements shown in Table 5.

Table 5: Computer Requirements

Item

CPU

Memory

Hard Disk

Operating System

Screen Resolution

Browser

Description

Pentium 500 MHz or higher

128 MB RAM or higher

50MB available space

Google Chrome 9 or later

Internet Explorer 7.0 or later

Mozilla Firefox 3.6 or later

Safari 5 or later

3.2. CPE Software

Microsoft : Windows XP, Windows Vista, Windows 7 or higher

Mac: MacOSX 10.5 or higher

1024 x 768 pixels or higher

The firmware of the CPE should be BaiCE_BG_1.5.4 or above, if the CPE is not running this version, please

download it from the Baicells website > Resources > Firmware or contact Baicells support.

3.3. Login

The CPE comes preloaded with a GUI to configure the device. With the CPE turned on and connected to the

router, access the GUI login page by opening a Web browser and entering http://192.168.150.1.

16

Figure 23: Login

Initially, use the default Username = admin/Password = admin (Figure 21).

Once you are in the GUI, you will want to change the password; please refer

to section 3.9.1 Account.

3.4. Status Menu

3.4.1.

Overview

After logging in, the GUI opens to the Status > Overview page (Figure 24). This page is a dashboard of key

information regarding the CPE. The top row, Current State, shows the network connection status, signal

intensity, LAN link status, and the number of smart devices (cell phones, pc's, laptops) connected to the

Internet through the CPE.

17

The Device Info pane displays the product name, software version, serial number, etc. The LTE Status pane

shows important operational information, such as the CPE's SIM card status and its IMSI and IMEI numbers,

wireless frequency being used, eNB connection status, and current signal strength and quality.

Under Throughput Statistics you will see downlink (DL) and uplink (UL) data rates for current throughput

(kbps), average rates, peak rates, and total throughput. The data is measured during a 3-second interval

every 5 minutes. The APN Status pane displays any gateway connections. The bottom pane, Devices List,

will show details about all smart devices currently connected through the CPE. Refer to Table 5 for a

description of the Status fields.

Figure 25: Status

Figure 26: Throughput Statistics

Figure 27: Internet Statistics

18

Figure 28: LAN Status

Figure 29: Device List

Table 6: Status

Field Name

Description

Connection State

Connection status between the CPE and the network – either Checking SIM, Scanning,

Signal Intensity

Indicates the strength of the signal between this CPE and the serving eNB, either

Registering, Acquiring IP, Connected, or Disconnected

excellent, good, general, bad, or severe. The ODU CPE hardware typically displays 1 to 5

LEDs to indicate this level (Figure 3&4).

Devices Connected

The number of smart devices connected to the Internet through this CPE via a LAN

Device Info

Product Name

Product Model

LTE ROUTER indicates the CPE is operating as a router

ODU CPE model number

Hardware Version

ODU CPE hardware version

LTE Module FW Name

LTE Module FW’s version

LTE Connection Time

The timer will be reset after every LTE connections

Software Version

ODU CPE operating software version

Software Build Time

Date and time the software was built

Serial Number

SN

IMEI

LTE Status

USIM

PLMN

PCI

eNB ID

EARFCN

System Up Time

The timer will be reset after reboot

International Mobile Equipment Identity is like a serial number for the SIM card

The Universal Subscriber Identity Module, or SIM, card status is either available or not

ready in the ODU CPE

IMSI

The unique International Mobile Subscriber Identity (IMSI) number associated with the

SIM card in the subscriber's ODU CPE. The IMSI must be identifiable by the operator's LTE

network in order to access it.

connected

The Public Land Mobile Number (PLMN), or operator network ID, to which the CPE is

The Physical Cell Identifier (PCI) unique to each eNB. PCI indicates to which eNB the

ODU CPE is connected. An operator can have multiple eNBs serving the same cell.

The operator's cell site ID to which the CPE is connected. A cell site may comprise more

than one eNB. Each eNB is given a PCI to identify it.

The E-UTRA Absolute Radio Frequency Channel Number (band and frequency) within

19



which the CPE operates

with an eNB, expressed in MHz

Bandwidth

The range of frequencies within the band the CPE may use for wireless communications

CINR

The Channel Signal-to-Interference-plus-Noise Ratio reflects the signal strength of the

signal received from the two antennas in the eNB, expressed in decibels (dB)

NOTE: Additional SINR values are reported when a transmitting device is using more than

two antennas.

DL Frequency

The frequency, in MHz, being used in the downlink (eNB to CPE). In LTE, the carrier

frequency in the uplink and downlink is designated by the EARFCN, which identifies the

UL Frequency

The frequency, in MHz, that the CPE is using in the uplink (CPE to eNB). In LTE, the carrier

frequency in the uplink and downlink is designated by the EARFCN, which identifies the

LTE band and carrier frequency.

LTE band and carrier frequency.

Reference Signal Receiving Quality indicates the quality of the wireless signal

Channel Quality indication

TXPWR (dBm)

Real time UE TX power

Roam

Roam status

Throughput Statistics

The current downlink data throughput rate, in Kbps

The current uplink data throughput rate, in Kbps

The average DL and UL data throughput rates, in Kbps, for this CPE in the last 3 minutes

The peak DL and UL data throughput rates, in Kbps, for this CPE in the last 3 minutes

The total (sum) DL and UL data throughput rates, in Kbps

Access Point Name (gateway) connection to other network devices. At least one APN

must be configured to establish the TR-069 connection to the CloudCore or other NMS

Enable

Indicates if the APN is enabled or disabled

MAC Address

MAC address of the APN gateway

Connection Type

Type of network connection

IPv4, IPv6, or IPv4v6 address of the APN gateway

Domain Name Server IP address

MAC Address

MAC address of the LAN device, e.g., router, to which the CPE is connected

The IP address of the LAN device

The subnet mask of the LAN device

Numerical ID assigned to each smart device connected through the ODU CPE

The name of each smart device connected through the CPE

The MAC address of each smart device connected through the CPE

The IP address of each device connected through the CPE

Amount of time a smart device’s IP address has been leased

Type of smart device connection

20

RSSI (dBm)

RSRQ (dBm)

CQI

DL

UL

Average

Peak

Sum

Internet Status

APN Number

IP Address

DNS server

LAN Status

IP Address

Netmask

Devices List

Index

Device Name

MAC Address

IP Address

Lease Time

Type

3.5. Network Menu

3.5.1. LAN Settings

Enter the Network > LAN DHCP Server enable, IP address, subnet mask, DHCP range, lease time, UPNP

enable.

Figure 30: DHCP Settings

DHCP Static Leases settings can set by the host’s MAC address.

Figure 31: DHCP Static Leases

21



3.5.2. WAN Settings

3.5.2.1. NAT Mode

The CPE will be worked at NAT mode, and all 8 APNs can be configured by Default router/Data/Mgmt/Voip

bear types.

Figure 32: WAN Settings

3.5.2.2. Router Mode

When selected Router mode, the CPE will worked at router mode, it can dynamic update router tables.

Figure 33: Router Mode

3.5.2.3. Tunnel Mode

This CPE can support L2TP and GER VPN mode.

22

Figure 34: Tunnel Mode

3.5.2.4. Bridge Mode

When the CPE worked at Bridge mode, the WAN ports address will bridge to LAN port, and the LAN port

will worked at trunk mode.

Figure 35: Bridge Mode

3.5.2.5. Mixed Mode

Mixed mode can configured every APN with different mode (e.g. Bridge), this is a professional mode.

23

Figure 36: Mixed Mode

3.5.3. Static Routes

Set Static routes of the CPE, it can configure LAN or WAN port routes, Gateway, Destination Network and

Route Subnet Mask, in Current Settings, show all activated static routes.

Figure 37: Static routes

24



3.5.4. DMZ

In technology, the DMZ refers to a firewall between incoming WAN traffic and the LAN to which the CPE is

connected. Two basic DMZ methods are (a) using a single firewall, also known as the three-legged model,

and (b) using dual firewalls (Figure 36). These architectures can be expanded to create complex

architectures depending on the network requirements.

Figure 38: DMZ

When the LAN has a DMZ/firewall server, you can enable DMZ on the CPE so that packets from the WAN

are forwarded to the firewall (Figure 37). Alternatively, you can enable Internet Control Message Protocol

(ICMP) redirect error messages to support Layer 2 multicast features.

Figure 39: DMZ Settings

3.5.5. UPnP

The Universal Plug & Play (UPnP) function provides a set of networking protocols that allows

device-to-device networking on a local network. When UPnP is enabled, devices seamlessly and

dynamically discover each other’s presence on the network and attach to one another and to network

services. Often, UPnP is used for streaming media between devices on the network.

Go to Security > UPnP to enable the CPE to be searched by other devices (Figure 38). Once enabled, any

redirects of traffic will display in the Active UPnP Redirects section of the window.

Figure 40: UPnP Settings

25



3.6. LTE Menu

3.6.1. Connection Settings

LTE connection settings includes Roaming settings, Default connection settings and Power Scan Option.

Figure 41: Connection Settings

3.6.1.1. Roaming setting

If set Roam enable, the CPE can access to other PLMN network, else the CPE just can access the network

PLMN same with the SIM card.

3.6.1.2. Default connection

If set always on, the CPE will automatic access the LTE network after booting, if set manual, the CPE need

manual connection to the LTE network.

Figure 42: Default Connection Settings

3.6.1.3. Power Scan Option

The CPE support two power scan options, the first is First Detected Cell, and the second is the Strongest

Cell.

26

Figure 43: Scan mode Settings

3.6.2. Edit APN Profile

An Access Point Name (APN) is the name of a gateway between a 3G/4G mobile network and another

computer network, frequently the public Internet. Generally, multiple APNs are used for different business

flows such as TR-069 management, voice, data, etc., and may support different services and QoS levels for

different subscribers.

Figure 44: APN Profiles

The CPE supports 8 APN configurations. At least one APN (TR-069) must be configured when the CPE/eNB

connect to the Baicells CloudCore. In the window (Figure 42) you will select the APN number (1-8), enable it,

enter an APN Name, select the type of IP addressing (IPv4, IPv6, or IPv4v6), identify if it is the default

gateway, and choose which type of protocol will be supported on it.

3.6.3. PIN Management

Use the PIN Management feature if you want to require users to enter a PIN code before they can use the

CPE to access the network (Figure 43). Once the PIN is enabled, you will need to remember it if you want to

later modify the number. You are limited to 3 tries to enter the correct PIN code before getting locked out.

If this happens, contact your service provider (end-users) or Baicells support (service providers).

27



Figure 45: PIN Management

3.6.4. Cell selection

The Cell selection determines which frequencies the CPE’s routine scan of available frequencies will cover.

Scanning is a process of tuning to a specific frequency and measuring the simplest signal quality [e.g.,

Received Signal Strength Indication (RSSI)].

As part of the cell selection and re-selection process, the CPE performs the scan first and then selects a

small number of candidate cells to go through the next step of measuring and evaluating signals to select

the best eNB that can serve it. The CPE frequently (milliseconds) performs the scan to ensure it has the best

possible connection to the network. Refer Figure 44.

Figure 46: Cell selections

Select one of the following options:

 Full Band (default) – All channels in the band.

− The CPE will routinely scan all channels in the band and all EARFCNs, increasing the time it

takes to connect compared to the other modes. The band is dependent on the CPE model.

 Dedicated EARFCN – Specific EARFCNs or frequencies. (Figure 45)

− The CPE will scan the dedicated EARFCN or frequency list first when it is powered on.

−

If the CPE cannot connect to the LTE network after scanning the list, it will scan other

supported bands and frequencies. You can add up to 10 EARFCNs or frequencies.

 Cell Lock – A combination of PCI + EARFCN or frequency. (Figure 46)

− The CPE is limited to scanning a specific list of eNBs based on both their Physical Cell

Identifier (PCI) and EARFCN or frequency. The CPE will scan the list of eNBs with the

EARFCN and PCI combination. Using this mode can accelerate network access time.

 PCI Lock – Specific PCIs only. Locks the CPE to a designated PCI or PCI range. (Figure 47)

After selecting an option, enter the required information and select ADD.

28

Figure 47: Dedicated EARFCN

Figure 48: Cell Lock

29

Figure 49: PCI Only Lock

3.6.5. SIM Lock Settings

This feature may be used to lock the SIM card to the operator's network (Figure 48). Each operator has a

unique Public Land Mobile Network (PLMN) number. Locking the SIM prohibits the users from accessing

another operator's network.

Figure 50: Throughput Statistics

3.6.6. MTU

Figure 51: MTU Settings

This is for setting the MTU of WAN (LTE) port, the range is from 1280 to 1500 Bytes.

30

3.7. Security Menu

3.7.1.

IP Filtering

When using a firewall server in the local network, invoke this setting to enable or disable the firewall for

this CPE (Figure 50).

Figure 52: Firewall Basic Settings

31

When enable IP/Port Filtering, then the IP/Port Filter can be set.

Figure 53: IP / Port Filtering

Settings:

(1) IP/Port Filtering Mode: Blacklist, White list

(2) IP/Port Filtering Log Dropped: enable / disable

(3) Destination IP Address: the destination IP Address of the filter

(4) Source IP Address: the source IP Address of the filter

(5) Protocol: TCP, UDP, TCP/UDP, ICMP, ALL

(6) Destination Port Range: the range of port

(7) Source Port Range: the range of port

(8) Schedule Index: Select box, if can be schedule by APPs

(9) Remarks

3.7.2.

IPv6 Filtering

When enable IP/Port Filtering, then the IP/Port Filter can be set.

Figure 54: IPv6 Filtering

Settings:

(1) IPv6 Filtering Mode: Blacklist, White list

(2) IPv6 Filtering Log Dropped: enable / disable

(3) Destination IP Address: the destination IP Address of the filter

(4) Source IP Address: the source IP Address of the filter

(5) Protocol: TCP, UDP, TCP/UDP, ICMPv6, ALL

(6) Destination Port Range: the range of port

(7) Source Port Range: the range of port

(8) Schedule Index: Select box, if can be schedule by APPs

(9) Remarks

3.7.3. MAC Filtering

Media Access Control (MAC) Filtering allows you to identify a list of devices either allowed to access or

forbidden from accessing the network through the CPE (Figure 53). Select Enable to enable MAC filtering,

and then determine whether you will allow or forbid the defined MAC addresses to access the network.

Figure 55: MAC Filtering

Settings:

(1) MAC Filtering Mode: Blacklist, White list

(2) MAC Filtering Log Dropped: enable / disable

32



(3) MAC Address: the filtering MAC address

3.7.4. URL Filtering

The Uniform Resource Location Filter (URL Filter) allows you to define a list of URL addresses users are

forbidden from accessing. When you enable the filter, a Settings window appears. Enter the specific URL

address users cannot access, as shown in Figure 54. To add more URL addresses, click on ADD. After

entering the addresses and saving, the URL(s) you enter will appear in the URL List.

Figure 56: URL Filtering

Settings:

(1) URL Filtering Mode: Blacklist, White list

(2) URL Filtering Log Dropped: enable / disable

(3) URL: the filtering URL

3.7.5. System Security

Figure 57: System Security

33



34

System Security Profiles, include High, Medium, None and Custom, every profiles will corresponding with a

set of System Security Settings.

Settings:

(1) Remote Web Login: enable / disable

(2) Remote Telnet: enable / disable

(3) Access Control List: enable / disable

(4) Block Port Scan: enable / disable

(5) Block Syn Flood: enable / disable

(6) SPI Firewall: enable / disable

3.7.6. Connect Limit

Connect Limit feature is used to control the number of connections through the UE to a host device, for

example, a peer-to-peer file sharing application such as BitTorrent. Such apps require a large amount of

bandwidth. By limiting the number of connections to the host device, you can control how much

bandwidth each active connection receives. You can configure a Connect Limit for up to 16 host devices.

Figure 58: Connect Limit

3.7.7. Schedule

This feature is set for a group schedule list, like start from 2020.8.18 to 2020.8.20 as a index of the

schedule.

Figure 59: Schedule List



In previous Filter configurations, you can select the schedule index like below figure.

Figure 60: Schedule Settings

3.8. NAT Menu

3.8.1. Port Forwarding

When NAT mode is enabled as the WAN interface type (section 3.5.2), you can redirect a communication

request from one address and port number combination to another. Only the IP address on the WAN side is

open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for example,

work as an FTP server), port forwarding is required so that all access requests to the external server port

from the Internet are redirected to the server on the LAN.

To add a port forwarding rule, select the Enable check box and click on ADD LIST (Figure 59). Enter the

parameters per the field descriptions in Table 7.

35

Figure 61: Port Forwarding settings

Table 7: Port Forwarding

Field Name

Description

WAN Port Range

Enter the port number range for the remote device in the format of 1000 to 1500

LAN IP Address

Enter the local host IP address. The address must be different from the IP address that is set

for the LAN Host Settings parameter, but they must be on the same network segment.

LAN Port

Protocol

Remarks

Enter the local port number. Range is 1 to 65,535.

Select the type of data protocol, either TCP, UDP, or TCP&UDP

3.8.2. Port Triggering

Port Triggering is a configuration option on a router - in this case, the CPE - if it is operating in NAT mode as

the WAN interface type (section 3.5.2). When an application uses a trigger port to build a connection, the

CPE will forward the data to the forward port.

To configure the feature, click on the check box next to Enable and then click on ADD LIST to enter the

service type, protocol, trigger port, and forward port (Figure 60).

Figure 62: Port Triggering Settings

36



3.8.3. ALG

The Application Layer Gateway (ALG) function provides a security component that augments a firewall or

the NAT used by the CPE (if WAN Network Mode = NAT). It allows customized NAT traversal filters to be

plugged into the gateway to support address and port translation for certain application layer control/data

protocols such as SIP, TFTP, PPTP, L2TP and IPSeC. You can enable the different types of application

protocols by clicking on the check box next to the protocol name (Figure 61).

Figure 63: Throughput Statistics

3.9. System Menu

3.9.1. Account

This menu is used to change the login password for the CPE (Figure 62). The password must be 5 to 12

characters. Baicells recommends using a combination of upper- and lower-case letters and numbers.

Figure 64: Account

3.9.2. WEB Settings

WEB Setting provides the ability to configure and manage the CPE remotely (Figure 63). This is especially

helpful when a user calls in for technical assistance. In section 3.3 Login, you used this Web application with

the default URL of http://192.168.150.1. Refer to Figure 65 for a description of each field.

Figure 66: WEB Settings

37

3.9.3. NTP

The operator's network may may use up to 4 Network Time Protocol (NTP) servers to provide correct

time-of-day to network devices. In the CPE GUI you can refresh the local time display using the SYNC WITH

BROWSER button; select the time zone that the CPE is in; and enable NTP client to use the default or

specified NTP servers for synchronization (Figure 64).

Figure 67: NTP Settings

3.9.4. TR-069

If your network operates using a TR-069 auto-configuration server (ACS), the ACS will automatically provide

the CPE configuration settings. Once you set up both the ACS and the CPE, you do not need to enter any

other parameters through the CPE GUI. Use the TR069 sub-menu to enable the TR-069 function for the CPE

(Figure 65). Refer to Figure 57 for a description of each field.

Figure 68: Throughput Statistics

38



3.9.5. TR-069 Certificate

This feature is used to upload the TR-069 certificate.

Figure 69: TR-069 Certificate

3.9.6. Restore / Update

Use the System > Restore/Update menu to reset the CPE to its factory default settings, to manually update

the firmware, or to manually update a module within the firmware - meaning to apply a patch to the

current firmware (Figure 67).

Caution: Performing a restore or update action will disrupt service.

3.9.6.1. Firmware Update

Caution: Do not power off the CPE or disconnect it from the computer during an upgrade.

To update (upgrade) the CPE to a different firmware version (Figure 67):

1. Download the image file from the Baicells support website (Baicells > Support > Downloads), and

save it to your computer.

2. Under Flash new firmware image, determine if you want to keep the current configuration settings

on the CPE . If you do, select the check box next to Keep settings.

3. Click on Choose File to navigate to the new image file on your computer, and then click on FLASH

IMAGE to initiate the upgrade.

After the upgrade, the CPE will restart automatically running the newer version of code.

3.9.6.2. Restore Factory Settings

To initiate a restore action, click on the PERFORM RESET button. The CPE will automatically reset its

configuration to the factory default values.

Figure 70: Restore & update

39



3.9.7. Diagnosis

3.9.7.1. TCPDump

Figure 71: TCPDump Settings

Settings:

(1) PC IP Address

(2) PC PORT

(3) Interface: ALL, LTE0PDN0 (APN0)

3.9.7.2. Ping

Figure 72: Ping Diagnosis Settings

Settings:

(1) IPv4/IPv6: Select the protocol

(2) IP Address/Domain: IP Address or URL

(3) Count: number of ping count

(4) Fragment: yes or no

(5) Packet size: 56~1400 Bytes (non-fragment)

40



3.9.7.3. Trace

Figure 73: Trace Diagnosis Settings

Settings:

(1) IPv4/IPv6: Select the protocol

(2) IP Address/Domain: IP Address or URL

3.9.7.4. Result

Figure 74: Diagnosis results

41

3.9.8. Backup Settings

This feature is used to backup the user settings, from the Web-GUI, you can Import / Export the settings.

Figure 75: Backup Settings



42

3.9.9. System Log

Figure 76: System Log

System log is the debug information of the CPE, when select the Setting, it can Export or Clear Logs.

Figure 77: System logs

3.9.10. System Messages

Use this Web-GUI, you can Export System Message, Collect real-time system information and transfer

system message to PC.

Figure 78: System Message Settings



Figure 79: System Messages

3.9.11. SAS Settings

This model can support DP and standalone modes, and all SAS parameters can be configured in Web-GUI,

43

Reboot after you finish setting.

3.10. Reboot

Use the Reboot menu to perform a reboot of the CPE, as shown in Figure 77. It can take several minutes for

the reboot to complete. After it reboots, the CPE GUI will display the login screen.

Caution: The reboot action will disrupt service.

Figure 80: Reboot

3.11. Logout

Figure 81: Throughput Statistics

When you click on the Logout menu, you are automatically logged out of the CPE and returned to the login

screen (Figure 78).

44

Appendix: Regulatory Compliance

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 40cm between the radiator & your

body.

ISEDC Compliance

This device complies with Innovation, Science, and Economic Development

Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d' Innovation, Science et Développement

économique Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

45









(1) l'appareil ne doit pas produire de brouillage, et

susceptible d'en compromettre le fonctionnement.

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least

40cm from all persons and must not be collocated or operating in conjunction with any other antenna

or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF

exposure compliance.

Les antennes utilisées pour cet émetteur doivent être installées de façon à offrir une distance de

séparation d'au moins 40cm entre toutes les personnes et ne doivent pas être colocalisées ou

fonctionner conjointement avec d'autres antennes ou transmetteurs. pour satisfaire la conformité à

l'exposition RF.

46



 

 

 

 

 

 

 

 

 

 

 

 

 

 

Baicells Technologies Co., Ltd.

Date: Jul. 15, 2021

File Name

Schematics.pdf

Block Diagram.pdf

Operational Description.pdf

Part List.pdf

Tune-up Procedure.pdf

Federal Communications Commission

Authorization and Evaluation Division

Confidentiality Request regarding application for certification of FCC ID: 2AG32EG8013LM11

Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential

treatment of information accompanying this application as outlined below:

Exhibit Type

Schematics

Block Diagram

Operational Description

Part List

Tune-up Procedure

The above materials contain trade secrets and proprietary information not customarily released to

the public. The public disclosure of these materials may be harmful to the applicant and provide

unjustified benefits to its competitors.

The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this

application and all accompanying documentation will not be made before the date of the Grant

for this application.

Sincerely,

Baicells Technologies Co., Ltd.

Signature

Back Huang / Manager

Typed name and Title



 

 

 

 

 

 

Baicells Technologies Co., Ltd. Date: 2021-07-15 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AG32EG8013LM11 To Whom It May Concern:

Sincerely, Signature

[Back Huang]

[Manager]

[Baicells Technologies Co., Ltd.]

This letter is to statement that EG8013L-M11/ LTE Outdoor CPE. has been tested according to FCC Part 15B by Waltek Testing Group Co., Ltd. (Test Report No.: WTD21D05046041E). And the SDOC file, meetting the requirements of the FCC regulations, would been provided when the device is sold by the responsible party in US. The service will not be sold until the SDOC is provided. If the sale does not have an SDOC, all responsibility is the responsibility of the applicant.

 

 

TEST REPORT

Reference No. ....................

: WTD21D05046043W002

FCC ID ................................

:

2AG32EG8013LM11

Applicant ............................

: Baicells Technologies Co., Ltd.

Address ..............................

:

9-10F, 1st Bldg., No.81 Beiqing Road, Haidian District, Beijing,

China

Manufacturer ....................

: Baicells Technologies Co., Ltd.

Address ..............................

9-10F, 1st Bldg., No.81 Beiqing Road, Haidian District, Beijing,

China

:

:

:

:

:

:

:

Product ...............................

LTE Outdoor CPE

Model(s). ............................

: EG8013L-M11

Brand Name .......................

Standards...........................

FCC Part 2.1091

Date of Receipt sample ....

2021-05-14

Date of Test .......................

2021-05-15 to 2021-07-08

Date of Issue ......................

2021-07-12

Test Result .........................

: Pass

Remarks:

The results shown in this test report refer only to the sample(s) tested, this test report cannot be

reproduced, except in full, without prior written permission of the company. The report would be invalid

without specific stamp of test institute and the signatures of compiler and approver.

Prepared By:

Waltek Testing Group Co., Ltd.

Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China

Tel: +86-769-2267 6998

Fax: +86-769-2267 6828

Compiled by:

Approved by:

Levi Xiao / Project Engineer

Daniel Liu / Designated Reviewer

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn

Page 1 of 7

Reference No.: WTD21D05046043W002

Page 2 of 7

2 Contents

Page

COVER PAGE ........................................................................................................................................... 1

CONTENTS ............................................................................................................................................................ 2 

REVISION HISTORY ............................................................................................................................................ 3 

GENERAL INFORMATION .................................................................................................................................. 4 

4.1  GENERAL DESCRIPTION OF E.U.T. ................................................................................................................ 4 

4.2  DETAILS OF E.U.T. ......................................................................................................................................... 4 

4.3  TEST FACILITY ................................................................................................................................................. 4 

TEST SUMMARY .................................................................................................................................................. 5 

RF EXPOSURE ...................................................................................................................................................... 6 

6.1  REQUIREMENTS ............................................................................................................................................... 6 

6.2  THE PROCEDURES / LIMIT ................................................................................................................................ 6 

6.3  MPE CALCULATION METHOD ......................................................................................................................... 7 

1

2 

3 

4 

5 

6 

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn

Reference No.: WTD21D05046043W002

Page 3 of 7

3 Revision History

Date of

Receipt

sample

Date of

Issue

Test report No.

Date of Test

Purpose

Comment

Approved

WTD21D05046

043W002

2021-05-15

to

2021-07-08

2021-05-14

2021-07-12

original

-

Valid

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn

Reference No.: WTD21D05046043W002

Page 4 of 7

4 General Information

4.1 General Description of E.U.T.

Product:

Model(s):

LTE Outdoor CPE

EG8013L-M11

Model Description:

N/A

Storage Location:

Internal Storage

4.2 Details of E.U.T.

Operation Frequency:

LTE Band 48:3550MHz-3700MHz

Type of Modulation:

LTE: Uplink: QPSK, 16QAM, 64QAM; Downlink: QPSK，16QAM，

64QAM

Antenna installation:

LTE: Internal antenna

Antenna Gain:

14dBi

Ratings:

DC 24V 0.5A

4.3 Test Facility

The test facility has a test site registered with the following organizations:

ISED CAB identifier: CN0013. Test Firm Registration No.: 7760A.

Waltek Testing Group Co., Ltd. Has been registered and fully described in a report filed with the

Industry Canada. The acceptance letter from the Industry Canada is maintained in our files.

Registration number 7760A, October 15, 2016.

FCC Designation No.: CN1201. Test Firm Registration No.: 523476.

Waltek Testing Group Co., Ltd. EMC Laboratory `has been registered and fully described in a report

filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is

maintained in our files. Registration number 523476, September 10, 2019.

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn

Reference No.: WTD21D05046043W002

Page 5 of 7

5

Test Summary

Test Items

Test Requirement

Result

Maximum Permissible Exposure

(Exposure of Humans to RF Fields)

FCC Part 2.1091

PASS

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn

Reference No.: WTD21D05046043W002

Page 6 of 7

6 RF Exposure

Test Requirement:

FCC Part 2.1091

Test Mode:

The EUT work in test mode(Tx).

6.1 Requirements

Systems operating under the provisions of this section shall be operated in a manner that ensures that

the public is not exposed to radio frequency energy levels in excess limit for maximum permissible

exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been

defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user

and the device.

6.2 The procedures / limit

FCC Part 1.1307:

(A) Limits for Occupational / Controlled Exposure

Frequency Range

(MHz)

Electric Field

Strength (E) (V/m)

Magnetic Field

Strength (H)

(A/m)

Power Density (S)

(mW/ cm2)

Averaging Time

|E|2,|H|2or S

(minutes)

(B) Limits for General Population / Uncontrolled Exposure

Frequency Range

(MHz)

Electric Field

Strength (E) (V/m)

Magnetic Field

Strength (H)

(A/m)

Power Density (S)

(mW/ cm2)

Averaging Time

|E|2,|H|2 or S

(minutes)

0.3-3.0

3.0-30

30-300

300-1500

1500-100,000

0.3-1.34

1.34-30

30-300

300-1500

1500-100,000

614

1842 / f

61.4

1.63

4.89 / f

0.163

614

824/f

27.5

1.63

2.19/f

0.073

Note: f = frequency in MHz ;

*Plane-wave equivalent power density

(100)*

(900 / f)*

1.0

F/300

5

(100)*

(180/f)*

F/1500

0.2

1.0

6

6

6

6

6

30

30

30

30

30

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn

Reference No.: WTD21D05046043W002

Page 7 of 7

6.3 MPE Calculation Method

Predication of MPE limit at a given distance

S = power density (in appropriate units, e.g. mW/cm2)

P = power input to the antenna (in appropriate units, e.g., mW).

G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain

factor, is normally numeric gain.

R = distance to the center of radiation of the antenna (appropriate units, e.g., cm)

From the peak EUT RF output power, the minimum mobile separation distance, d=40cm, as well as the

gain of the used antenna, the RF power density can be obtained

Remark:

FCC Part 2.1091:

Mode

Antenna

Gain (dBi)

Antenna Gain

(numeric)

Max.Peak Output

Power (dBm)

Peak Output

Power (mW)

Power Density

(mW/cm2)

Limit of Power

Density (mW/cm2)

LTE

14.00

25.119

25.79

379.31

0.473871

1

======End of Report======

Waltek Testing Group Co., Ltd.

http://www.waltek.com.cn



 

 

Baicells Technologies Co., Ltd. FCC ID: 2AG32EG8013LM11 POWER OF ATTORNEY Date: Jul. 15, 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Jul. 14, 2022. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Baicells Technologies Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang / Manager Typed name and Title