| all | frequencies |
|
|
|
|
exhibits | applications |
|---|---|---|---|---|---|---|---|
| manual | photos | label | |||||
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual | Users Manual | 2.14 MiB | July 21 2021 | |||
| 1 |
|
Internal Photos | Internal Photos | 3.22 MiB | July 21 2021 | |||
| 1 |
|
External Photos | External Photos | 631.31 KiB | July 21 2021 | |||
| 1 |
|
Label Info & Location | ID Label/Location Info | 238.41 KiB | July 21 2021 | |||
| 1 |
|
Confidentiality Letter | Cover Letter(s) | 144.84 KiB | July 21 2021 | |||
| 1 |
|
FCC SDOC | Attestation Statements | 44.21 KiB | July 21 2021 | |||
| 1 |
|
MPE | RF Exposure Info | 295.74 KiB | July 21 2021 | |||
| 1 |
|
Power of Attorney Letter | Cover Letter(s) | 156.80 KiB | July 21 2021 | |||
| 1 |
|
Test Report | Test Report | 4.40 MiB | July 21 2021 | |||
| 1 |
|
Test Setup Photos | Test Setup Photos | 117.53 KiB | July 21 2021 |
| 1 | User Manual | Users Manual | 2.14 MiB | July 21 2021 |
ATOM OD06 CPE
Installation &
Configuration Guide
Model EG8013L-M11-EUD
April 2020
Version 1.0
1
About This Document
This document is for operators who will be installing and configuring the Baicells ATOM OD06 CPEs, model
EG8013L-M11-EUD.
This document version is based on the firmware version BaiCE_BG_1.6.11.
All technical specifications and documents are on the Baicells website under Resources > Documentation.
Related Documents
Baicells SNAP PoE+ Router Data Sheet
Baicells SNAP PoE+ Router User Manual
Baicells ATOM OD06H/L Data Sheet
Copyright Notice
Baicells Technologies, Inc., copyrights the information in this document. No part of this document may be reproduced
in any form or means without the prior written consent of Baicells Technologies, Inc. The Baicells logo is a proprietary
trademark of Baicells Technologies, Inc. Other trademarks mentioned in this document belong to their owners.
Description
SMEs/Contributors
Author/Editor
-
Tang Houcheng
Revision Record
Date
18-Aug-2020
Version
v1.0
Draft
Support Resources
Contact Us
Documentation - Baicells product data sheets, this document, and other technical manuals may be found at
Baicells > Resources > Documentation.
Support - Open a support ticket, process an RMA, and the Support Forum are at Baicells > Support.
Baicells Technologies Co., Ltd.
Baicells Technologies North America, Inc.
China
North America
Address:
9-10F,1stBldg.,No.81BeiqingRoad,Haidian
District,Beijing,China
555 Republic Dr., #200, Plano, TX 75074, USA
Phone:
+86-10-62607100
+1-888-502-5585
Email:
contact@Baicells.com
sales_na@Baicells.com or support_na@Baicells.com36T
Website: www.Baicells.com
https://na.Baicells.com
2
Table of Contents
List of Figures ..................................................................................................................................................................... 4
List of Tables ....................................................................................................................................................................... 6
Introduction .............................................................................................................................................................. 7
1.
Description ............................................................................................................................................................ 7
1.1.
ODU Modes........................................................................................................................................................... 7
1.2.
Features ................................................................................................................................................................ 9
1.3.
Installation ................................................................................................................................................................. 9
2.
Part & Materials .................................................................................................................................................... 9
2.1.
Dimensions ......................................................................................................................................................... 10
2.2.
LEDs & Interfaces ................................................................................................................................................ 10
2.3.
Preparing to Install .............................................................................................................................................. 11
2.4.
Installation .......................................................................................................................................................... 11
2.5.
Installation with Baicells SNAP Router ................................................................................................................ 15
2.6.
Configuration ........................................................................................................................................................... 16
3.
Computer Requirements..................................................................................................................................... 16
3.1.
CPE Software ....................................................................................................................................................... 16
3.2.
Login.................................................................................................................................................................... 16
3.3.
Status Menu ........................................................................................................................................................ 17
3.4.
3.4.1.
Overview ........................................................................................................................................................ 17
Network Menu .................................................................................................................................................... 21
3.5.
LAN Settings.................................................................................................................................................... 21
3.5.1.
3.5.2. WAN Settings ...................................................................................................................................................... 22
3.5.2.1. NAT Mode ....................................................................................................................................................... 22
Router Mode .................................................................................................................................................. 22
3.5.2.2.
Tunnel Mode .................................................................................................................................................. 22
3.5.2.3.
3.5.2.4.
Bridge Mode ................................................................................................................................................... 23
3.5.2.5. Mixed Mode ................................................................................................................................................... 23
Static Routes ................................................................................................................................................... 24
3.5.3.
DMZ ................................................................................................................................................................ 25
3.5.4.
3.5.5.
UPnP ............................................................................................................................................................... 25
LTE Menu ............................................................................................................................................................ 26
3.6.
Connection Settings ........................................................................................................................................ 26
3.6.1.
3.6.1.1.
Roaming setting .............................................................................................................................................. 26
3.6.1.2. Default connection ......................................................................................................................................... 26
Power Scan Option ......................................................................................................................................... 26
3.6.1.3.
Edit APN Profile .............................................................................................................................................. 27
3.6.2.
PIN Management ............................................................................................................................................ 27
3.6.3.
Cell selection .................................................................................................................................................. 28
3.6.4.
SIM Lock Settings ............................................................................................................................................ 30
3.6.5.
MTU ................................................................................................................................................................ 30
3.6.6.
Security Menu ..................................................................................................................................................... 31
3.7.
IP Filtering ....................................................................................................................................................... 31
3.7.1.
IPv6 Filtering ................................................................................................................................................... 31
3.7.2.
MAC Filtering .................................................................................................................................................. 32
3.7.3.
URL Filtering ................................................................................................................................................... 33
3.7.4.
3
System Security .............................................................................................................................................. 33
3.7.5.
Connect Limit.................................................................................................................................................. 34
3.7.6.
Schedule ......................................................................................................................................................... 34
3.7.7.
NAT Menu ........................................................................................................................................................... 35
3.8.
Port Forwarding .............................................................................................................................................. 35
3.8.1.
Port Triggering ................................................................................................................................................ 36
3.8.2.
ALG ................................................................................................................................................................. 37
3.8.3.
System Menu ...................................................................................................................................................... 37
3.9.
3.9.1.
Account ........................................................................................................................................................... 37
3.9.2. WEB Settings ....................................................................................................................................................... 37
NTP ................................................................................................................................................................. 38
3.9.3.
3.9.4. TR-069 ................................................................................................................................................................. 38
3.9.5. TR-069 Certificate ............................................................................................................................................... 39
Restore / Update ............................................................................................................................................ 39
3.9.6.
Firmware Update ............................................................................................................................................ 39
3.9.6.1.
Restore Factory Settings ................................................................................................................................. 39
3.9.6.2.
Diagnosis ........................................................................................................................................................ 40
3.9.7.
TCPDump ........................................................................................................................................................ 40
3.9.7.1.
Ping ................................................................................................................................................................. 40
3.9.7.2.
Trace ............................................................................................................................................................... 41
3.9.7.3.
Result .............................................................................................................................................................. 41
3.9.7.4.
Backup Settings .............................................................................................................................................. 41
3.9.8.
System Log ...................................................................................................................................................... 42
3.9.9.
System Messages ............................................................................................................................................ 42
3.9.10.
3.10. Reboot ................................................................................................................................................................ 43
3.11.
Logout ................................................................................................................................................................. 43
Appendix: Regulatory Compliance ................................................................................................................................... 45
FCC Compliance ............................................................................................................................................................... 45
List of Figures
FIGURE 1: LTE NETWORK ARCHITECTURE .................................................................................................................................... 7
FIGURE 2: DIMENSIONS ......................................................................................................................................................... 10
FIGURE 3: LOW-GAIN LEDS & INTERFACES ................................................................................................................................ 10
FIGURE 5: LTE NETWORK ARCHITECTURE .................................................................................................................................. 12
FIGURE 6: POE ADAPTOR ....................................................................................................................................................... 12
FIGURE 7: LOW GAIN CPE GROUNDING .................................................................................................................................... 12
FIGURE 9: POWER ADAPTOR ................................................................................................................................................... 13
FIGURE 10: RUBBER BAND ..................................................................................................................................................... 13
FIGURE 11: BRACKET ............................................................................................................................................................. 13
FIGURE 12: ATTACH UE ......................................................................................................................................................... 14
FIGURE 16: MARK HOLES FOR DRILLING ................................................................................................................................... 14
FIGURE 17: FIX BRACKET TO WALL ........................................................................................................................................... 14
FIGURE 18: ATTACH UE ......................................................................................................................................................... 14
FIGURE 21: LOGIN ................................................................................................................................................................ 17
FIGURE 22: STATUS ............................................................................................................................................................... 18
FIGURE 23: THROUGHPUT STATISTICS ....................................................................................................................................... 18
4
FIGURE 24: INTERNET STATISTICS ............................................................................................................................................. 18
FIGURE 25: LAN STATUS ........................................................................................................................................................ 19
FIGURE 26: DEVICE LIST ......................................................................................................................................................... 19
FIGURE 27: DHCP SETTINGS .................................................................................................................................................. 21
FIGURE 28: DHCP STATIC LEASES ............................................................................................................................................ 21
FIGURE 29: WAN SETTINGS ................................................................................................................................................... 22
FIGURE 30: ROUTER MODE .................................................................................................................................................... 22
FIGURE 31: TUNNEL MODE .................................................................................................................................................... 23
FIGURE 32: BRIDGE MODE ..................................................................................................................................................... 23
FIGURE 33: MIXED MODE ...................................................................................................................................................... 24
FIGURE 35: STATIC ROUTES ..................................................................................................................................................... 24
FIGURE 36: DMZ ................................................................................................................................................................. 25
FIGURE 37: DMZ SETTINGS.................................................................................................................................................... 25
FIGURE 38: UPNP SETTINGS................................................................................................................................................... 25
FIGURE 39: CONNECTION SETTINGS ......................................................................................................................................... 26
FIGURE 40: DEFAULT CONNECTION SETTINGS ............................................................................................................................. 26
FIGURE 41: SCAN MODE SETTINGS ........................................................................................................................................... 27
FIGURE 42: APN PROFILES ..................................................................................................................................................... 27
FIGURE 43: PIN MANAGEMENT .............................................................................................................................................. 28
FIGURE 44: CELL SELECTIONS .................................................................................................................................................. 28
FIGURE 45: DEDICATED EARFCN ............................................................................................................................................ 29
FIGURE 46: CELL LOCK ........................................................................................................................................................... 29
FIGURE 47: PCI ONLY LOCK .................................................................................................................................................... 30
FIGURE 48: THROUGHPUT STATISTICS ....................................................................................................................................... 30
FIGURE 49: MTU SETTINGS ................................................................................................................................................... 30
FIGURE 50: FIREWALL BASIC SETTINGS...................................................................................................................................... 31
FIGURE 51: IP / PORT FILTERING ............................................................................................................................................. 31
FIGURE 52: IPV6 FILTERING .................................................................................................................................................... 32
FIGURE 53: MAC FILTERING ................................................................................................................................................... 32
FIGURE 54: URL FILTERING .................................................................................................................................................... 33
FIGURE 55: SYSTEM SECURITY ................................................................................................................................................. 33
FIGURE 56: CONNECT LIMIT ................................................................................................................................................... 34
FIGURE 57: SCHEDULE LIST ..................................................................................................................................................... 34
FIGURE 58: SCHEDULE SETTINGS ............................................................................................................................................. 35
FIGURE 59: PORT FORWARDING SETTINGS ................................................................................................................................. 35
FIGURE 60: PORT TRIGGERING SETTINGS................................................................................................................................... 36
FIGURE 61: THROUGHPUT STATISTICS ....................................................................................................................................... 37
FIGURE 62: ACCOUNT ........................................................................................................................................................... 37
FIGURE 63: WEB SETTINGS .................................................................................................................................................... 37
FIGURE 64: NTP SETTINGS ..................................................................................................................................................... 38
FIGURE 65: THROUGHPUT STATISTICS ....................................................................................................................................... 38
FIGURE 66: TR-069 CERTIFICATE ............................................................................................................................................ 39
FIGURE 67: RESTORE & UPDATE .............................................................................................................................................. 39
FIGURE 68: TCPDUMP SETTINGS ............................................................................................................................................ 40
FIGURE 69: PING DIAGNOSIS SETTINGS ..................................................................................................................................... 40
FIGURE 70: TRACE DIAGNOSIS SETTINGS ................................................................................................................................... 41
FIGURE 71: DIAGNOSIS RESULTS .............................................................................................................................................. 41
FIGURE 72: BACKUP SETTINGS ................................................................................................................................................ 41
5
FIGURE 73: SYSTEM LOG ........................................................................................................................................................ 42
FIGURE 74: SYSTEM LOGS ....................................................................................................................................................... 42
FIGURE 75: SYSTEM MESSAGE SETTINGS ................................................................................................................................... 42
FIGURE 76: SYSTEM MESSAGES ............................................................................................................................................... 43
FIGURE 77: REBOOT .............................................................................................................................................................. 43
FIGURE 78: THROUGHPUT STATISTICS ....................................................................................................................................... 44
List of Tables
TABLE 1: PARTS ...................................................................................................................................................................... 9
TABLE 2: MATERIALS ............................................................................................................................................................. 10
TABLE 3: INSTALLATION PROCEDURE ......................................................................................................................................... 15
TABLE 4: COMPUTER REQUIREMENTS ....................................................................................................................................... 16
TABLE 5: STATUS ................................................................................................................................................................... 19
TABLE 7: PORT FORWARDING .................................................................................................................................................. 36
6
1.
Introduction
1.1. Description
The Baicells Atom OD0406 Outdoor Low-Gain and Outdoor High-Gain User Equipment (UE) is part of a
broadband wireless access system that integrates with Long-Term Evolution (LTE) backhaul networks to
provide subscribers with Internet access. The UE, also referred to as Customer Premise Equipment (CPE),
communicates through a wireless connection to the operator’s eNodeB’s (eNB) at cell sites located in the
region. The eNBs communicate with the backhaul network (Figure 1).
Figure 2: LTE Network Architecture
The outdoor low-gain or high-gain UE may be selected because of the distance between the user's location
and the closest eNB or for environments where there may be blockage or partial blockage in the wireless
signal path between the UE and eNBs in the area - e.g., dense trees or buildings.
As an LTE standards-based product, the Baicells equipment provides higher near-line-of-sight (nLOS) and
non-line-of-sight (NLOS) signal penetration than other wireless technologies. The high-gain UE has a higher
antenna gain than the low-gain UE, making it possible to get the strongest possible signal reception for
subscribers.
The LTE standards organization that defines certain characteristics of user equipment across manufacturers
labels each progression of the standards as releases, such as Release 9, Release 10, etc., and categories,
such as Category 4 (CAT4) and Category 6/7 (CAT6/7).
Typically the difference from one release/category to the next is in capacity, i.e., higher throughput. There
is no physical difference between the CAT4 and CAT6/7 UE, but the low-gain UE and the high-gain UE do
look different from one another. A physical comparison is provided in section 4.
1.2. ODU Modes
This device can work at two modes, ODU standalone or IDU+ODU mode.
(1) ODU standalone Mode
Standalone mode, ODU can worked at NAT/TUNNEL/BRIDGE mode
7
a) NAT Mode, the ODU work as a LTE and Ethernet Gateway, it converts LTE network data to local
Ethernet data.
b) Tunnel Mode, the ODU can build a L2 or L3 VPN tunnel with a designated VPN server.
c) Bridge Mode, the ODU can bridge it LTE IP address to LAN port devices, when configured as the
bridge, the CPE’s LAN port will work as trunk mode, so it can’t assign IP address to any no-trunk
devices (like PC), so you have to Manual Configure the PC’s IP address in the same broadcast
domain (e.g. 192.168.150.88).
(2) IDU+ODU Mode
When the ODU connect to a IDU device (Baicells PoE router), it will automatic be configured as Bridge
mode, and assign all its LTE IP to IDU, at that mode, the IDU will take the place of ODU to control all the CPE
functions.
Before contacting Baicells FAE or your distributor, please DO NOT mixed use the two
modes.
CAUTION:
8
1.3. Features
The Baicells Atom UEs provide robust throughput and are designed for growth and expansion as
technology evolves. Some of the key features and attributes of the Atom outdoor UEs are listed below.
Exact specifications vary by model. For the latest information, please refer to the Baicells website for your
specific UE model.
Standardized LTE TDD bands 48. Customization may be requested.
Complies with 3GPP Release 10 (CAT6/7)
1000 Mbps Ethernet interface (CAT6/7)
Built-in bipolar directional LTE antenna
Power supply using Power Over Ethernet (PoE)
Cell lock, SIM lock, and Pin lock
Pole or wall mount options
TR-069 management protocol support
Local and remote GUI management
2.
Installation
2.1. Part & Materials
Table 1: Parts
Item
Atom
OD06L-EG8013L-M11-EUD
CPE
Power Cable
PoE Power Adaptor
Qty
1
1
1
Refer to Table 1 for a list of the components that you should receive with the Baicells outdoor UE.
Picture
You will need standard tools, Ethernet cable, ground wire, and RJ-45 connectors for installing and
connecting the outdoor unit (Table 2).
9
Table 2: Materials
Item
Description
Ethernet Cable
Ground Wire
Outdoor shield CAT5E, shorter than 330 feet
16mm2 yellow-green wire
2.2. Dimensions
The Baicells Atom outdoor low-gain and high-gain models of user equipment are powerful, standards-based
devices designed to connect seamlessly to any standard LTE eNB operating on the same frequency band.
The devices have a small, sleek form factor (Figure 3), yet are ruggedized for the most challenging outdoor
environments.
Figure 4: Dimensions
All models of the low-gain and high-gain UEs have external LED status indicator lights and interface
connectors (Figure 3). These external features make it easier to determine the UE's operational status and
to check cables.
2.3. LEDs & Interfaces
On the low-gain UE the LEDs are on the side of the unit, and the connection interfaces are on the bottom of
the unit. On the high-gain UE both the LEDs and the interfaces are on the side of the unit. Refer to Table 3
for a description of the LEDs and Table 4 for a description of the interfaces.
Figure 5: Low-Gain LEDs & Interfaces
10
Table 3: LEDs
LEDs vary by model – not all models will have all of the LEDs listed below.
Identity
Description
Color
Description
MIU
-
Yellow
Steady On
Reserved for future use
Reserved for future use
Status
Off
LTE
LTE network status
Blue
Blinking
Reserved. for future use
Off
The UE is not connected to the network
Steady On
The UE is connected to the LTE network
Steady On
The USIM card is functioning normally
SIM/USIM
SIM/USIM card status
Yellow
The USIM card is not inserted or is not
Blinking
functioning normally
100 or 1000 Mbps Local
Off
No Ethernet connection established
LAN
Area Network
Yellow
Steady On
Ethernet connection is normal
Ethernet status
PWR
Power status
Yellow
Blinking
Data is transmitting
Off
No power supply to the UE
Steady On
Power to the UE is on
LTE Signal
more bars, the stronger
Green
1, 2, 3, 4, or 5 bars to
indicate wireless
connection status. The
the signal between the
UE and a network cell
(eNB).
The signal is too weak for the UE to connect to
All Off
the network
Steady On
strength
Bars will light steadily according to signal
The UE is scanning the network
Blinking
The UE is authenticating with the network
The UE is getting an IP address from the
network
Table 4: Interfaces
Interfaces
PoE
TF or SD Slot
SIM/USIM Slot
RESET
GND
Interfaces vary by model – not all models will have all of the interfaces listed below.
Description
Power over Ethernet (PoE) power adaptor
Card slot for a secure digital (SD) card
Universal Subscriber Identity Module card slot, 1.8V/3.0V USIM 2FF
Reset/restore button
Ground lug. The unit is connected to Earth by conductor.
2.4. Preparing to Install
To help ensure a smooth and successful installation, check that you have all of the parts, materials, and
tools you will need, per section 2.1 Parts & Materials. When selecting the best outdoor location for the
installation, plan on placing the UE so that it faces the nearest eNB. You may need to adjust the tilt and
angle for optimum signal reception.
2.5. Installation
1. Loosen the screws on the UE's waterproof cover, and open the cover.
11
2.
Insert the service provider's SIM/USIM card into the card slot (Figure 6).
Attention: Never power on the unit while installing or uninstalling the USIM card. Doing so
could damage the card and the unit.
Figure 7: LTE Network Architecture
3. Prepare the outdoor shielded CAT5E Ethernet cable. The Ethernet cable will run between the
outdoor UE and the inside of the facility, where it will connect to the PoE adaptor and LAN. Cable
length will vary by location.
4. Connect one end of the Ethernet cable to the PoE port on the unit. Connect the other end to the
power adaptor (Figure 8).
Figure 9: PoE Adaptor
5. Close the UE’s waterproof cover, and tighten the screws.
6. Prepare the 16mm2 yellow-green ground wire, and follow the steps below. Once the unit is fully
installed, make sure the grounding cable is connected to a solid grounding point (earth).
a. Atom Low-Gain UE: Connect the ground cable to the ground screw (Figure 10).
Figure 11: Low gain CPE Grounding
12
13
b. Atom High-Gain UE: Connect the ground cable to the grounding screw in the ground row
(Figure 6). The figure is showing the UE mounted on a pole; mounting is covered in step 8.
7. Plug the power adaptor into an electrical outlet (Figure 12). Pay attention to the power adaptor
interface directions noted on the adaptor itself. The LED indicators should light up when the unit is
powered on.
Figure 13: Power Adaptor
8. Mount the UE: If you are installing the UE on a pole, e.g., to attach to a roof, go to step 9. If you are
installing the UE on an outside wall, go to step 10.
9. Pole installation:
a. Low-Gain UE:
Figure 15: Rubber Band
a1) Attach a heavy-duty anti-slip rubber band on the pole (Figure 14).
a2) Fix the UE bracket over the band using the hoop (Figure 16).
Figure 17: Bracket
a3) Attach the UE to the bracket, and tighten the screw (Figure 18).
Figure 19: Attach UE
a4) The UE is now ready for installation at its final outside location. Then, proceed to section 7
a1) Slip the bracket off of the Atom unit, and fit it on the wall to mark the drilling locations
(Figure 11), The marked locations, drill four 10-mm diameter and 70-mm depth holes.
Figure 20: Mark Holes for Drilling
Basic Configuration.
10. Wall installation:
a.
Low-Gain UE:
screws (Figure 12).
Figure 21: Fix Bracket to Wall
a2) Check the up/down direction of the bracket, and then fix it on the wall using the M5 tapping
a3) Attach the UE to the bracket, and tighten the screw (Figure13).
Figure 22: Attach UE
14
a4) Proceed to section 7 Basic Configuration.
2.6. Installation with Baicells SNAP Router
To explain the installation, the procedure in Table 3 uses a Baicells Atom OD04L Outdoor Low-Gain CPE as
the example. Refer to the CPE user manual on the Baicells website to complete some steps as indicated.
Table 4: Installation Procedure
1. With the CPE powered OFF, loosen the screws on the
3. Using the Ethernet cable, connect the CPE PoE port
waterproof cover and lift to access the interfaces.
and the router WAN port.
2. Insert the SIM card into the SIM slot.
Attention: Never power on the CPE while
installing or uninstalling the SIM card. Doing so could
damage the card and the unit.
Caution: Do not connect unsupported devices to
the router WAN port, as it may cause damage.
Per the associated steps in the CPE user manual
installation procedure:
4. Prepare the ground wire and connect one end of it to
the CPE ground terminal and the other end to a
reliable grounding point (earth).
5. Close the CPE's waterproof cover, and tighten the
screws.
6. Mount the CPE at its outdoor location, assuring proper
alignment to the nearest eNB tower.
7. Power the CPE ON, and check the satus of the LEDs to
ensure it is operating as expected.
8. Connect the router's power adapter to the power
connector on the back of the unit, and the other
end to a power outlet.
9. Turn power to the router ON.
10. Check the LED indicators to verify normal
operating status per Table 2 in section 2.2 of this
guide.
15
NOTE: If either the CPE or the router is not running the correct firmware, the router's LTE signal LED
will be OFF. Check for the latest firmware on the Baicells website, or contact Baicells support.
The setup is complete and ready to work. To configure features using the CPE GUI, go to the next section.
3. Configuration
3.1. Computer Requirements
The computer you use to connect with the CPE GUI must meet the requirements shown in Table 5.
Table 5: Computer Requirements
Item
CPU
Memory
Hard Disk
Operating System
Screen Resolution
Browser
Description
Pentium 500 MHz or higher
128 MB RAM or higher
50MB available space
Google Chrome 9 or later
Internet Explorer 7.0 or later
Mozilla Firefox 3.6 or later
Safari 5 or later
3.2. CPE Software
Microsoft : Windows XP, Windows Vista, Windows 7 or higher
Mac: MacOSX 10.5 or higher
1024 x 768 pixels or higher
The firmware of the CPE should be BaiCE_BG_1.5.4 or above, if the CPE is not running this version, please
download it from the Baicells website > Resources > Firmware or contact Baicells support.
3.3. Login
The CPE comes preloaded with a GUI to configure the device. With the CPE turned on and connected to the
router, access the GUI login page by opening a Web browser and entering http://192.168.150.1.
16
Figure 23: Login
Initially, use the default Username = admin/Password = admin (Figure 21).
Once you are in the GUI, you will want to change the password; please refer
to section 3.9.1 Account.
3.4. Status Menu
3.4.1.
Overview
After logging in, the GUI opens to the Status > Overview page (Figure 24). This page is a dashboard of key
information regarding the CPE. The top row, Current State, shows the network connection status, signal
intensity, LAN link status, and the number of smart devices (cell phones, pc's, laptops) connected to the
Internet through the CPE.
17
The Device Info pane displays the product name, software version, serial number, etc. The LTE Status pane
shows important operational information, such as the CPE's SIM card status and its IMSI and IMEI numbers,
wireless frequency being used, eNB connection status, and current signal strength and quality.
Under Throughput Statistics you will see downlink (DL) and uplink (UL) data rates for current throughput
(kbps), average rates, peak rates, and total throughput. The data is measured during a 3-second interval
every 5 minutes. The APN Status pane displays any gateway connections. The bottom pane, Devices List,
will show details about all smart devices currently connected through the CPE. Refer to Table 5 for a
description of the Status fields.
Figure 25: Status
Figure 26: Throughput Statistics
Figure 27: Internet Statistics
18
Figure 28: LAN Status
Figure 29: Device List
Table 6: Status
Field Name
Description
Connection State
Connection status between the CPE and the network – either Checking SIM, Scanning,
Signal Intensity
Indicates the strength of the signal between this CPE and the serving eNB, either
Registering, Acquiring IP, Connected, or Disconnected
excellent, good, general, bad, or severe. The ODU CPE hardware typically displays 1 to 5
LEDs to indicate this level (Figure 3&4).
Devices Connected
The number of smart devices connected to the Internet through this CPE via a LAN
Device Info
Product Name
Product Model
LTE ROUTER indicates the CPE is operating as a router
ODU CPE model number
Hardware Version
ODU CPE hardware version
LTE Module FW Name
LTE Module FW’s version
LTE Connection Time
The timer will be reset after every LTE connections
Software Version
ODU CPE operating software version
Software Build Time
Date and time the software was built
Serial Number
SN
IMEI
LTE Status
USIM
PLMN
PCI
eNB ID
EARFCN
System Up Time
The timer will be reset after reboot
International Mobile Equipment Identity is like a serial number for the SIM card
The Universal Subscriber Identity Module, or SIM, card status is either available or not
ready in the ODU CPE
IMSI
The unique International Mobile Subscriber Identity (IMSI) number associated with the
SIM card in the subscriber's ODU CPE. The IMSI must be identifiable by the operator's LTE
network in order to access it.
connected
The Public Land Mobile Number (PLMN), or operator network ID, to which the CPE is
The Physical Cell Identifier (PCI) unique to each eNB. PCI indicates to which eNB the
ODU CPE is connected. An operator can have multiple eNBs serving the same cell.
The operator's cell site ID to which the CPE is connected. A cell site may comprise more
than one eNB. Each eNB is given a PCI to identify it.
The E-UTRA Absolute Radio Frequency Channel Number (band and frequency) within
19
which the CPE operates
with an eNB, expressed in MHz
Bandwidth
The range of frequencies within the band the CPE may use for wireless communications
CINR
The Channel Signal-to-Interference-plus-Noise Ratio reflects the signal strength of the
signal received from the two antennas in the eNB, expressed in decibels (dB)
NOTE: Additional SINR values are reported when a transmitting device is using more than
two antennas.
DL Frequency
The frequency, in MHz, being used in the downlink (eNB to CPE). In LTE, the carrier
frequency in the uplink and downlink is designated by the EARFCN, which identifies the
UL Frequency
The frequency, in MHz, that the CPE is using in the uplink (CPE to eNB). In LTE, the carrier
frequency in the uplink and downlink is designated by the EARFCN, which identifies the
LTE band and carrier frequency.
LTE band and carrier frequency.
RSRQ (dBm)
Reference Signal Receiving Quality indicates the quality of the wireless signal
TXPWR (dBm)
Real time UE TX power
Channel Quality indication
Throughput Statistics
Roam status
The current downlink data throughput rate, in Kbps
The current uplink data throughput rate, in Kbps
The average DL and UL data throughput rates, in Kbps, for this CPE in the last 3 minutes
The peak DL and UL data throughput rates, in Kbps, for this CPE in the last 3 minutes
The total (sum) DL and UL data throughput rates, in Kbps
Access Point Name (gateway) connection to other network devices. At least one APN
must be configured to establish the TR-069 connection to the CloudCore or other NMS
Enable
Indicates if the APN is enabled or disabled
MAC Address
MAC address of the APN gateway
Connection Type
Type of network connection
IPv4, IPv6, or IPv4v6 address of the APN gateway
Domain Name Server IP address
MAC Address
MAC address of the LAN device, e.g., router, to which the CPE is connected
The IP address of the LAN device
The subnet mask of the LAN device
Numerical ID assigned to each smart device connected through the ODU CPE
The name of each smart device connected through the CPE
The MAC address of each smart device connected through the CPE
The IP address of each device connected through the CPE
Amount of time a smart device’s IP address has been leased
Type of smart device connection
20
CQI
Roam
DL
UL
Average
Peak
Sum
Internet Status
APN Number
IP Address
DNS server
LAN Status
IP Address
Netmask
Devices List
Index
Device Name
MAC Address
IP Address
Lease Time
Type
3.5. Network Menu
3.5.1. LAN Settings
Enter the Network > LAN DHCP Server enable, IP address, subnet mask, DHCP range, lease time, UPNP
enable.
Figure 30: DHCP Settings
DHCP Static Leases settings can set by the host’s MAC address.
Figure 31: DHCP Static Leases
21
3.5.2. WAN Settings
3.5.2.1. NAT Mode
The CPE will be worked at NAT mode, and all 8 APNs can be configured by Default router/Data/Mgmt/Voip
bear types.
Figure 32: WAN Settings
3.5.2.2. Router Mode
When selected Router mode, the CPE will worked at router mode, it can dynamic update router tables.
Figure 33: Router Mode
3.5.2.3. Tunnel Mode
This CPE can support L2TP and GER VPN mode.
22
Figure 34: Tunnel Mode
3.5.2.4. Bridge Mode
When the CPE worked at Bridge mode, the WAN ports address will bridge to LAN port, and the LAN port
will worked at trunk mode.
Figure 35: Bridge Mode
3.5.2.5. Mixed Mode
Mixed mode can configured every APN with different mode (e.g. Bridge), this is a professional mode.
23
Figure 36: Mixed Mode
3.5.3. Static Routes
Set Static routes of the CPE, it can configure LAN or WAN port routes, Gateway, Destination Network and
Route Subnet Mask, in Current Settings, show all activated static routes.
Figure 37: Static routes
24
3.5.4. DMZ
In technology, the DMZ refers to a firewall between incoming WAN traffic and the LAN to which the CPE is
connected. Two basic DMZ methods are (a) using a single firewall, also known as the three-legged model,
and (b) using dual firewalls (Figure 36). These architectures can be expanded to create complex
architectures depending on the network requirements.
Figure 38: DMZ
When the LAN has a DMZ/firewall server, you can enable DMZ on the CPE so that packets from the WAN
are forwarded to the firewall (Figure 37). Alternatively, you can enable Internet Control Message Protocol
(ICMP) redirect error messages to support Layer 2 multicast features.
Figure 39: DMZ Settings
3.5.5. UPnP
The Universal Plug & Play (UPnP) function provides a set of networking protocols that allows
device-to-device networking on a local network. When UPnP is enabled, devices seamlessly and
dynamically discover each other’s presence on the network and attach to one another and to network
services. Often, UPnP is used for streaming media between devices on the network.
Go to Security > UPnP to enable the CPE to be searched by other devices (Figure 38). Once enabled, any
redirects of traffic will display in the Active UPnP Redirects section of the window.
Figure 40: UPnP Settings
25
3.6. LTE Menu
3.6.1. Connection Settings
LTE connection settings includes Roaming settings, Default connection settings and Power Scan Option.
Figure 41: Connection Settings
3.6.1.1. Roaming setting
If set Roam enable, the CPE can access to other PLMN network, else the CPE just can access the network
PLMN same with the SIM card.
3.6.1.2. Default connection
If set always on, the CPE will automatic access the LTE network after booting, if set manual, the CPE need
manual connection to the LTE network.
Figure 42: Default Connection Settings
3.6.1.3. Power Scan Option
The CPE support two power scan options, the first is First Detected Cell, and the second is the Strongest
Cell.
26
Figure 43: Scan mode Settings
3.6.2. Edit APN Profile
An Access Point Name (APN) is the name of a gateway between a 3G/4G mobile network and another
computer network, frequently the public Internet. Generally, multiple APNs are used for different business
flows such as TR-069 management, voice, data, etc., and may support different services and QoS levels for
different subscribers.
Figure 44: APN Profiles
The CPE supports 8 APN configurations. At least one APN (TR-069) must be configured when the CPE/eNB
connect to the Baicells CloudCore. In the window (Figure 42) you will select the APN number (1-8), enable it,
enter an APN Name, select the type of IP addressing (IPv4, IPv6, or IPv4v6), identify if it is the default
gateway, and choose which type of protocol will be supported on it.
3.6.3. PIN Management
Use the PIN Management feature if you want to require users to enter a PIN code before they can use the
CPE to access the network (Figure 43). Once the PIN is enabled, you will need to remember it if you want to
later modify the number. You are limited to 3 tries to enter the correct PIN code before getting locked out.
If this happens, contact your service provider (end-users) or Baicells support (service providers).
27
Figure 45: PIN Management
3.6.4. Cell selection
The Cell selection determines which frequencies the CPE’s routine scan of available frequencies will cover.
Scanning is a process of tuning to a specific frequency and measuring the simplest signal quality [e.g.,
Received Signal Strength Indication (RSSI)].
As part of the cell selection and re-selection process, the CPE performs the scan first and then selects a
small number of candidate cells to go through the next step of measuring and evaluating signals to select
the best eNB that can serve it. The CPE frequently (milliseconds) performs the scan to ensure it has the best
possible connection to the network. Refer Figure 44.
Figure 46: Cell selections
Select one of the following options:
Full Band (default) – All channels in the band.
− The CPE will routinely scan all channels in the band and all EARFCNs, increasing the time it
takes to connect compared to the other modes. The band is dependent on the CPE model.
Dedicated EARFCN – Specific EARFCNs or frequencies. (Figure 45)
− The CPE will scan the dedicated EARFCN or frequency list first when it is powered on.
−
If the CPE cannot connect to the LTE network after scanning the list, it will scan other
supported bands and frequencies. You can add up to 10 EARFCNs or frequencies.
Cell Lock – A combination of PCI + EARFCN or frequency. (Figure 46)
− The CPE is limited to scanning a specific list of eNBs based on both their Physical Cell
Identifier (PCI) and EARFCN or frequency. The CPE will scan the list of eNBs with the
EARFCN and PCI combination. Using this mode can accelerate network access time.
PCI Lock – Specific PCIs only. Locks the CPE to a designated PCI or PCI range. (Figure 47)
After selecting an option, enter the required information and select ADD.
28
Figure 47: Dedicated EARFCN
Figure 48: Cell Lock
29
Figure 49: PCI Only Lock
3.6.5. SIM Lock Settings
This feature may be used to lock the SIM card to the operator's network (Figure 48). Each operator has a
unique Public Land Mobile Network (PLMN) number. Locking the SIM prohibits the users from accessing
another operator's network.
Figure 50: Throughput Statistics
3.6.6. MTU
Figure 51: MTU Settings
This is for setting the MTU of WAN (LTE) port, the range is from 1280 to 1500 Bytes.
30
3.7. Security Menu
3.7.1.
IP Filtering
When using a firewall server in the local network, invoke this setting to enable or disable the firewall for
this CPE (Figure 52).
Figure 52: Firewall Basic Settings
31
When enable IP/Port Filtering, then the IP/Port Filter can be set.
Figure 53: IP / Port Filtering
Settings:
(1) IP/Port Filtering Mode: Blacklist, White list
(2) IP/Port Filtering Log Dropped: enable / disable
(3) Destination IP Address: the destination IP Address of the filter
(4) Source IP Address: the source IP Address of the filter
(5) Protocol: TCP, UDP, TCP/UDP, ICMP, ALL
(6) Destination Port Range: the range of port
(7) Source Port Range: the range of port
(8) Schedule Index: Select box, if can be schedule by APPs
(9) Remarks
3.7.2.
IPv6 Filtering
When enable IP/Port Filtering, then the IP/Port Filter can be set.
Figure 54: IPv6 Filtering
Settings:
(1) IPv6 Filtering Mode: Blacklist, White list
(2) IPv6 Filtering Log Dropped: enable / disable
(3) Destination IP Address: the destination IP Address of the filter
(4) Source IP Address: the source IP Address of the filter
(5) Protocol: TCP, UDP, TCP/UDP, ICMPv6, ALL
(6) Destination Port Range: the range of port
(7) Source Port Range: the range of port
(8) Schedule Index: Select box, if can be schedule by APPs
(9) Remarks
3.7.3. MAC Filtering
Media Access Control (MAC) Filtering allows you to identify a list of devices either allowed to access or
forbidden from accessing the network through the CPE (Figure 53). Select Enable to enable MAC filtering,
and then determine whether you will allow or forbid the defined MAC addresses to access the network.
Figure 55: MAC Filtering
Settings:
(1) MAC Filtering Mode: Blacklist, White list
(2) MAC Filtering Log Dropped: enable / disable
32
(3) MAC Address: the filtering MAC address
3.7.4. URL Filtering
The Uniform Resource Location Filter (URL Filter) allows you to define a list of URL addresses users are
forbidden from accessing. When you enable the filter, a Settings window appears. Enter the specific URL
address users cannot access, as shown in Figure 54. To add more URL addresses, click on ADD. After
entering the addresses and saving, the URL(s) you enter will appear in the URL List.
Figure 56: URL Filtering
Settings:
(1) URL Filtering Mode: Blacklist, White list
(2) URL Filtering Log Dropped: enable / disable
(3) URL: the filtering URL
3.7.5. System Security
Figure 57: System Security
33
System Security Profiles, include High, Medium, None and Custom, every profiles will corresponding with a
set of System Security Settings.
Settings:
(1) Remote Web Login: enable / disable
(2) Remote Telnet: enable / disable
(3) Access Control List: enable / disable
(4) Block Port Scan: enable / disable
(5) Block Syn Flood: enable / disable
(6) SPI Firewall: enable / disable
3.7.6. Connect Limit
Connect Limit feature is used to control the number of connections through the UE to a host device, for
example, a peer-to-peer file sharing application such as BitTorrent. Such apps require a large amount of
bandwidth. By limiting the number of connections to the host device, you can control how much
bandwidth each active connection receives. You can configure a Connect Limit for up to 16 host devices.
Figure 58: Connect Limit
3.7.7. Schedule
This feature is set for a group schedule list, like start from 2020.8.18 to 2020.8.20 as a index of the
schedule.
Figure 59: Schedule List
34
35
In previous Filter configurations, you can select the schedule index like below figure.
Figure 60: Schedule Settings
3.8. NAT Menu
3.8.1. Port Forwarding
When NAT mode is enabled as the WAN interface type (section 3.5.2), you can redirect a communication
request from one address and port number combination to another. Only the IP address on the WAN side is
open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for example,
work as an FTP server), port forwarding is required so that all access requests to the external server port
from the Internet are redirected to the server on the LAN.
To add a port forwarding rule, select the Enable check box and click on ADD LIST (Figure 59). Enter the
parameters per the field descriptions in Table 7.
Figure 61: Port Forwarding settings
Table 7: Port Forwarding
Field Name
Description
WAN Port Range
Enter the port number range for the remote device in the format of 1000 to 1500
LAN IP Address
Enter the local host IP address. The address must be different from the IP address that is set
for the LAN Host Settings parameter, but they must be on the same network segment.
LAN Port
Protocol
Remarks
Enter the local port number. Range is 1 to 65,535.
Select the type of data protocol, either TCP, UDP, or TCP&UDP
3.8.2. Port Triggering
Port Triggering is a configuration option on a router - in this case, the CPE - if it is operating in NAT mode as
the WAN interface type (section 3.5.2). When an application uses a trigger port to build a connection, the
CPE will forward the data to the forward port.
To configure the feature, click on the check box next to Enable and then click on ADD LIST to enter the
service type, protocol, trigger port, and forward port (Figure 62).
Figure 62: Port Triggering Settings
36
3.8.3. ALG
The Application Layer Gateway (ALG) function provides a security component that augments a firewall or
the NAT used by the CPE (if WAN Network Mode = NAT). It allows customized NAT traversal filters to be
plugged into the gateway to support address and port translation for certain application layer control/data
protocols such as SIP, TFTP, PPTP, L2TP and IPSeC. You can enable the different types of application
protocols by clicking on the check box next to the protocol name (Figure 63).
Figure 63: Throughput Statistics
3.9. System Menu
3.9.1. Account
This menu is used to change the login password for the CPE (Figure 62). The password must be 5 to 12
characters. Baicells recommends using a combination of upper- and lower-case letters and numbers.
Figure 64: Account
3.9.2. WEB Settings
WEB Setting provides the ability to configure and manage the CPE remotely (Figure 63). This is especially
helpful when a user calls in for technical assistance. In section 3.3 Login, you used this Web application with
the default URL of http://192.168.150.1. Refer to Figure 65 for a description of each field.
Figure 66: WEB Settings
37
3.9.3. NTP
The operator's network may may use up to 4 Network Time Protocol (NTP) servers to provide correct
time-of-day to network devices. In the CPE GUI you can refresh the local time display using the SYNC WITH
BROWSER button; select the time zone that the CPE is in; and enable NTP client to use the default or
specified NTP servers for synchronization (Figure 64).
Figure 67: NTP Settings
3.9.4. TR-069
If your network operates using a TR-069 auto-configuration server (ACS), the ACS will automatically provide
the CPE configuration settings. Once you set up both the ACS and the CPE, you do not need to enter any
other parameters through the CPE GUI. Use the TR069 sub-menu to enable the TR-069 function for the CPE
(Figure 65). Refer to Figure 57 for a description of each field.
Figure 68: Throughput Statistics
38
3.9.5. TR-069 Certificate
This feature is used to upload the TR-069 certificate.
Figure 69: TR-069 Certificate
3.9.6. Restore / Update
Use the System > Restore/Update menu to reset the CPE to its factory default settings, to manually update
the firmware, or to manually update a module within the firmware - meaning to apply a patch to the
current firmware (Figure 67).
Caution: Performing a restore or update action will disrupt service.
3.9.6.1. Firmware Update
Caution: Do not power off the CPE or disconnect it from the computer during an upgrade.
To update (upgrade) the CPE to a different firmware version (Figure 67):
1. Download the image file from the Baicells support website (Baicells > Support > Downloads), and
save it to your computer.
2. Under Flash new firmware image, determine if you want to keep the current configuration settings
on the CPE . If you do, select the check box next to Keep settings.
3. Click on Choose File to navigate to the new image file on your computer, and then click on FLASH
IMAGE to initiate the upgrade.
After the upgrade, the CPE will restart automatically running the newer version of code.
3.9.6.2. Restore Factory Settings
To initiate a restore action, click on the PERFORM RESET button. The CPE will automatically reset its
configuration to the factory default values.
Figure 70: Restore & update
39
3.9.7. Diagnosis
3.9.7.1. TCPDump
Figure 71: TCPDump Settings
Settings:
(1) PC IP Address
(2) PC PORT
(3) Interface: ALL, LTE0PDN0 (APN0)
3.9.7.2. Ping
Figure 72: Ping Diagnosis Settings
Settings:
(1) IPv4/IPv6: Select the protocol
(2) IP Address/Domain: IP Address or URL
(3) Count: number of ping count
(4) Fragment: yes or no
(5) Packet size: 56~1400 Bytes (non-fragment)
40
3.9.7.3. Trace
Figure 73: Trace Diagnosis Settings
Settings:
(1) IPv4/IPv6: Select the protocol
(2) IP Address/Domain: IP Address or URL
3.9.7.4. Result
Figure 74: Diagnosis results
41
3.9.8. Backup Settings
This feature is used to backup the user settings, from the Web-GUI, you can Import / Export the settings.
Figure 75: Backup Settings
42
3.9.9. System Log
Figure 76: System Log
System log is the debug information of the CPE, when select the Setting, it can Export or Clear Logs.
Figure 77: System logs
3.9.10. System Messages
Use this Web-GUI, you can Export System Message, Collect real-time system information and transfer
system message to PC.
Figure 78: System Message Settings
Figure 79: System Messages
3.10. Reboot
Use the Reboot menu to perform a reboot of the CPE, as shown in Figure 80. It can take several minutes for
the reboot to complete. After it reboots, the CPE GUI will display the login screen.
Caution: The reboot action will disrupt service.
Figure 80: Reboot
3.11. Logout
When you click on the Logout menu, you are automatically logged out of the CPE and returned to the login
screen (Figure 81).
43
Figure 81: Throughput Statistics
44
Appendix: Regulatory Compliance
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
45
| 1 | Confidentiality Letter | Cover Letter(s) | 144.84 KiB | July 21 2021 |
Baicells Technologies Co., Ltd. Date: Jul. 16, 2021 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AG32EG8013LM11EUD Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics Block Diagram Operational Description Schematics.pdf Block Diagram.pdf Operational Description.pdf Part List Tune-up Procedure Part List.pdf Tune-up Procedure.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang / Manager Typed name and Title
| 1 | FCC SDOC | Attestation Statements | 44.21 KiB | July 21 2021 |
Baicells Technologies Co., Ltd. Date: 2021-07-16 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AG32EG8013LM11EUD To Whom It May Concern: This letter is to statement that EG8013L-M11-EUD/ LTE Outdoor CPE. has been tested according to FCC Part 15B by Waltek Testing Group Co., Ltd. (Test Report No.: WTD21D06062210E). And the SDOC file, meetting the requirements of the FCC regulations, would been provided when the device is sold by the responsible party in US. The service will not be sold until the SDOC is provided. If the sale does not have an SDOC, all responsibility is the responsibility of the applicant. Sincerely, Signature [Back Huang] [Manager] [Baicells Technologies Co., Ltd.]
| 1 | Power of Attorney Letter | Cover Letter(s) | 156.80 KiB | July 21 2021 |
Baicells Technologies Co., Ltd. FCC ID: 2AG32EG8013LM11EUD POWER OF ATTORNEY Date: Jul. 16, 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Jul. 15, 2022. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Baicells Technologies Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang / Manager Typed name and Title
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2021-07-21 | 3560 ~ 3690 | CBE - Citizens Band End User Devices | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2021-07-21
|
||||
| 1 | Applicant's complete, legal business name |
Baicells Technologies Co., Ltd.
|
||||
| 1 | FCC Registration Number (FRN) |
0025156423
|
||||
| 1 | Physical Address |
9-10F,1stBldg.,No.81BeiqingRoad,Haidian District
|
||||
| 1 |
Beijing, N/A
|
|||||
| 1 |
China
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
T******@timcoengr.com
|
||||
| 1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
2AG32
|
||||
| 1 | Equipment Product Code |
EG8013LM11EUD
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
B****** H********
|
||||
| 1 | Telephone Number |
+86-0********
|
||||
| 1 | Fax Number |
+86-0********
|
||||
| 1 |
h******@baicells.com
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | CBE - Citizens Band End User Devices | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | LTE Outdoor CPE | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Output Power is EIRP. This transmitter is limited to professional installation and outdoor operations. This device must be installed and operated so as to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. This device supports LTE of 5, 10, 15, and 20 MHz bandwidth modes for TDD LTE Band 48. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
WALTEK TESTING GROUP CO., LTD.
|
||||
| 1 | Name |
P**** Z********
|
||||
| 1 | Telephone Number |
+86-7********
|
||||
| 1 |
P******@waltek.com.cn
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 96 | EP MO | 3555 | 3695 | 0.191 | 0.0312 ppm | 8M93G7D | |||||||||||||||||||||||||||||||||
| 1 | 2 | 96 | EP MO | 3555 | 3695 | 0.156 | 0.0312 ppm | 8M92W7D | |||||||||||||||||||||||||||||||||
| 1 | 3 | 96 | EP MO | 3557.5 | 3692.5 | 0.184 | 0.0306 ppm | 13M4G7D | |||||||||||||||||||||||||||||||||
| 1 | 4 | 96 | EP MO | 3557.5 | 3692.5 | 0.136 | 0.0306 ppm | 13M4W7D | |||||||||||||||||||||||||||||||||
| 1 | 5 | 96 | EP MO | 3560 | 3690 | 0.188 | 0.0314 ppm | 17M9G7D | |||||||||||||||||||||||||||||||||
| 1 | 6 | 96 | EP MO | 3560 | 3690 | 0.16 | 0.0314 ppm | 17M9W7D | |||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC