FCC ID: 2AG32EG8015GM11EUD LTE Outdoor CPE

ATOM OD15 CPE Installation &

Configuration Guide Model EG8015G-M11-EUD April 2020 Version 1.2 1 This document is for operators who will be installing and configuring the Baicells ATOM OD15 CPEs, model All technical specifications and documents are on the Baicells website under Resources > Documentation. About This Document EG8015G-M11-EUD. Related Documents Baicells SNAP PoE+ Router Data Sheet Baicells SNAP PoE+ Router User Manual Baicells ATOM OD06H/L Data Sheet Copyright Notice Revision Record Date 18-Nov-2020 Version v1.0 Support Resources Contact Us Baicells Technologies, Inc., copyrights the information in this document. No part of this document may be reproduced in any form or means without the prior written consent of Baicells Technologies, Inc. The Baicells logo is a proprietary trademark of Baicells Technologies, Inc. Other trademarks mentioned in this document belong to their owners. Description SMEs/Contributors Author/Editor

Tang Houcheng Documentation - Baicells product data sheets, this document, and other technical manuals may be found at Baicells > Resources > Documentation. Support - Open a support ticket, process an RMA, and the Support Forum are at Baicells > Support. Baicells Technologies Co., Ltd. Baicells Technologies North America, Inc. China North America Address:

9-10F,1stBldg.,No.81BeiqingRoad,Haidian District,Beijing,China 555 Republic Dr., #200, Plano, TX 75074, USA Phone:

+86-10-62607100

+1-888-502-5585 Email:

contact@Baicells.com sales_na@Baicells.com or support_na@Baicells.com36T Website: www.Baicells.com https://na.Baicells.com 2 Table of Contents Introduction .............................................................................................................................................................. 5 1. Description ............................................................................................................................................................ 5 1.1. ODU Modes........................................................................................................................................................... 5 1.2. Features ................................................................................................................................................................ 7 1.3. Installation ................................................................................................................................................................. 7 2. Part & Materials .................................................................................................................................................... 7 2.1. LEDs & Interfaces .................................................................................................................................................. 8 2.2. CPE Software ......................................................................................................................................................... 9 2.3. Login...................................................................................................................................................................... 9 2.4. Status Menu .......................................................................................................................................................... 9 2.5. Overview .......................................................................................................................................................... 9 2.5.1. Network Menu .................................................................................................................................................... 13 2.6. 2.6.1. LAN Settings.................................................................................................................................................... 13 2.6.2. WAN Settings ...................................................................................................................................................... 14 2.6.2.1. NAT Mode ....................................................................................................................................................... 14 Router Mode .................................................................................................................................................. 14 2.6.2.2. 2.6.2.3. Tunnel Mode .................................................................................................................................................. 14 Bridge Mode ................................................................................................................................................... 15 2.6.2.4. 2.6.2.5. Mixed Mode ................................................................................................................................................... 15 Static Routes ................................................................................................................................................... 16 2.6.3. DMZ ................................................................................................................................................................ 17 2.6.4. 2.6.5. UPnP ............................................................................................................................................................... 17 LTE Menu ............................................................................................................................................................ 18 2.7. Connection Settings ........................................................................................................................................ 18 2.7.1. 2.7.1.1. Roaming setting .............................................................................................................................................. 18 2.7.1.2. Default connection ......................................................................................................................................... 18 Power Scan Option ......................................................................................................................................... 18 2.7.1.3. Edit APN Profile .............................................................................................................................................. 19 2.7.2. PIN Management ............................................................................................................................................ 19 2.7.3. Cell selection .................................................................................................................................................. 20 2.7.4. SIM Lock Settings ............................................................................................................................................ 22 2.7.5. 2.7.6. MTU ................................................................................................................................................................ 22 Security Menu ..................................................................................................................................................... 23 2.8. IP Filtering ....................................................................................................................................................... 23 2.8.1. IPv6 Filtering ................................................................................................................................................... 23 2.8.2. MAC Filtering .................................................................................................................................................. 24 2.8.3. URL Filtering ................................................................................................................................................... 25 2.8.4. System Security .............................................................................................................................................. 25 2.8.5. Connect Limit.................................................................................................................................................. 26 2.8.6. Schedule ......................................................................................................................................................... 26 2.8.7. NAT Menu ........................................................................................................................................................... 27 2.9. Port Forwarding .............................................................................................................................................. 27 2.9.1. Port Triggering ................................................................................................................................................ 28 2.9.2. 2.9.3. ALG ................................................................................................................................................................. 29 System Menu ...................................................................................................................................................... 29 2.10. 3 2.10.1. Account ........................................................................................................................................................... 29 2.10.2. WEB Settings .................................................................................................................................................. 29 NTP ................................................................................................................................................................. 30 2.10.3. TR-069 ............................................................................................................................................................ 30 2.10.4. TR-069 Certificate ........................................................................................................................................... 31 2.10.5. Restore / Update ............................................................................................................................................ 31 2.10.6. Firmware Update ....................................................................................................................................... 31 2.10.6.1. Restore Factory Settings ............................................................................................................................. 31 2.10.6.2. Diagnosis ........................................................................................................................................................ 32 2.10.7. TCPDump .................................................................................................................................................... 32 2.10.7.1. Ping............................................................................................................................................................. 32 2.10.7.2. Trace ........................................................................................................................................................... 33 2.10.7.3. Result ......................................................................................................................................................... 33 2.10.7.4. Backup Settings .............................................................................................................................................. 33 2.10.8. 2.10.9. System Log ...................................................................................................................................................... 34 2.10.10. System Messages ............................................................................................................................................ 34 2.11. Reboot ................................................................................................................................................................ 35 Logout ................................................................................................................................................................. 35 2.12. Appendix: Regulatory Compliance ................................................................................................................................... 37 FCC Compliance ............................................................................................................................................................... 37 4 1. Introduction 1.1. Description The Baicells Atom OD15 Low-Gain and High-Gain User Equipment (UE) is part of a broadband wireless access system that integrates with Long-Term Evolution (LTE) backhaul networks to provide subscribers with Internet access. The UE, also referred to as Customer Premise Equipment (CPE), communicates through a wireless connection to the operators eNodeBs (eNB) at cell sites located in the region. The eNBs communicate with the backhaul network . Figure 1: LTE Network Architecture The low-gain or high-gain UE may be selected because of the distance between the user's location and the closest eNB or for environments where there may be blockage or partial blockage in the wireless signal path between the UE and eNBs in the area - e.g., dense trees or buildings. As an LTE standards-based product, the Baicells equipment provides higher near-line-of-sight (nLOS) and non-line-of-sight (NLOS) signal penetration than other wireless technologies. The high-gain UE has a higher antenna gain than the low-gain UE, making it possible to get the strongest possible signal reception for subscribers. The LTE standards organization that defines certain characteristics of user equipment across manufacturers labels each progression of the standards as releases, such as Release 9, Release 10, etc., and categories, such as Category 4 (CAT4) and Category 6/7 (CAT6/7). Typically the difference from one release/category to the next is in capacity, i.e., higher throughput. There is no physical difference between the CAT4 and CAT6/7 UE, but the low-gain UE and the high-gain UE do look different from one another. A physical comparison is provided in section 4. 1.2. ODU Modes This device can work at two modes, ODU standalone or IDU+ODU mode.

(1) ODU standalone Mode Standalone mode, ODU can worked at NAT/TUNNEL/BRIDGE mode 5 a) NAT Mode, the ODU work as a LTE and Ethernet Gateway, it converts LTE network data to local Ethernet data. b) Tunnel Mode, the ODU can build a L2 or L3 VPN tunnel with a designated VPN server. c) Bridge Mode, the ODU can bridge it LTE IP address to LAN port devices, when configured as the bridge, the CPEs LAN port will work as trunk mode, so it cant assign IP address to any no-trunk devices (like PC), so you have to Manual Configure the PCs IP address in the same broadcast domain (e.g. 192.168.150.88).

(2) IDU+ODU Mode When the ODU connect to a IDU device (Baicells PoE router), it will automatic be configured as Bridge mode, and assign all its LTE IP to IDU, at that mode, the IDU will take the place of ODU to control all the CPE functions. Before contacting Baicells FAE or your distributor, please DO NOT mixed use the two modes. CAUTION:

6 1.3. Features The Baicells Atom UEs provide robust throughput and are designed for growth and expansion as technology evolves. Some of the key features and attributes of the Atom UEs are listed below. Exact specifications vary by model. For the latest information, please refer to the Baicells website for your specific UE model. Standardized LTE TDD bands 48. Customization may be requested. Complies with 3GPP Release 11 (CAT12/15) 1000 Mbps Ethernet interface Built-in bipolar directional LTE antenna Power supply using Power Over Ethernet (PoE) Cell lock, SIM lock, and Pin lock Pole or wall mount options TR-069 management protocol support Local and remote GUI management 2. Installation 2.1. Part & Materials Refer to Table 1 for a list of the components that you should receive with the Baicells UE. Table 1: Parts Item Atom OD15 unit Qty 1 Picture Power Cable 1 PoE Power Adaptor 1 7 Atom OD15 Mounting Bracket 1 each You will need standard tools, Ethernet cable, ground wire, and RJ-45 connectors for installing and connecting the unit (Table 2). Table 2: Materials Item Description Ethernet Cable Ground Wire shield CAT5E, shorter than 330 feet 16mm2 yellow-green wire 2.2. LEDs & Interfaces On the low-gain UE the LEDs are on the side of the unit, and the connection interfaces are on the bottom of the unit. On the high-gain UE both the LEDs and the interfaces are on the side of the unit. For a description of the LEDs and a description of the interfaces. Table 3: LEDs LEDs vary by model not all models will have all of the LEDs listed below. Identity Description LTE network and USIM L&S status Color Blue Status Off The UE is not connected to the network Steady On The UE is connected to the LTE network Description PWR Power status Yellow Off No power supply to the UE Steady On Power to the UE is on LTE Signal Green L/M/H 3 bars to indicate wireless connection status. The more bars, the stronger the signal between the UE and a network cell (eNB). Table 4: Interfaces The signal is too weak for the UE to connect to All Off the network Steady On strength Bars will light steadily according to signal The UE is scanning the network Blinking The UE is authenticating with the network The UE is getting an IP address from the network Interfaces vary by model not all models will have all of the interfaces listed below. Interfaces PoE SIM/USIM Slot Description Power over Ethernet (PoE) power adaptor Universal Subscriber Identity Module card slot, 1.8V/3.0V USIM 2FF 8 Interfaces RESET GND Description Reset/restore button Ground lug. The unit is connected to Earth by conductor. 2.3. CPE Software The firmware of the CPE should be BaiCE_BG_1.5.4 or above, if the CPE is not running this version, please download it from the Baicells website > Resources > Firmware or contact Baicells support. The CPE comes preloaded with a GUI to configure the device. With the CPE turned on and connected to the router, access the GUI login page by opening a Web browser and entering http://192.168.150.1. Initially, use the default Username = admin/Password = admin (Figure 21). Once you are in the GUI, you will want to change the password; please refer to section 3.9.1 Account. 2.4. Login Figure 2: Login 2.5. Status Menu 2.5.1. Overview After logging in, the GUI opens to the Status > Overview page. This page is a dashboard of key information regarding the CPE. The top row, Current State, shows the network connection status, signal intensity, LAN link status, and the number of smart devices (cell phones, pc's, laptops) connected to the Internet through the CPE. 9 The Device Info pane displays the product name, software version, serial number, etc. The LTE Status pane shows important operational information, such as the CPE's SIM card status and its IMSI and IMEI numbers, wireless frequency being used, eNB connection status, and current signal strength and quality. Under Throughput Statistics you will see downlink (DL) and uplink (UL) data rates for current throughput

(kbps), average rates, peak rates, and total throughput. The data is measured during a 3-second interval every 5 minutes. The APN Status pane displays any gateway connections. The bottom pane, Devices List, will show details about all smart devices currently connected through the CPE. Refer to Table 5 for a description of the Status fields. Figure 3: Status Figure 4: Throughput Statistics Figure 5: Internet Statistics 10 Figure 6: LAN Status Figure 7: Device List Table 3: Status Field Name Description Connection State Connection status between the CPE and the network either Checking SIM, Scanning, Registering, Acquiring IP, Connected, or Disconnected Signal Intensity Indicates the strength of the signal between this CPE and the serving eNB, either excellent, good, general, bad, or severe. The ODU CPE hardware typically displays 1 to 5 Devices Connected The number of smart devices connected to the Internet through this CPE via a LAN or LEDs to indicate this level (Figure 3&4). Wireless LAN (WLAN)/Wi-Fi connection Device Info Product Name Product Model LTE ROUTER indicates the CPE is operating as a router ODU CPE model number Hardware Version ODU CPE hardware version LTE Module FW Name LTE Module FWs version LTE Connection Time The timer will be reset after every LTE connections Software Version ODU CPE operating software version Software Build Time Date and time the software was built Serial Number SN IMEI LTE Status USIM PLMN PCI System Up Time The timer will be reset after reboot International Mobile Equipment Identity is like a serial number for the SIM card The Universal Subscriber Identity Module, or SIM, card status is either available or not ready in the ODU CPE IMSI The unique International Mobile Subscriber Identity (IMSI) number associated with the SIM card in the subscriber's ODU CPE. The IMSI must be identifiable by the operator's LTE network in order to access it. connected The Public Land Mobile Number (PLMN), or operator network ID, to which the CPE is The Physical Cell Identifier (PCI) unique to each eNB. PCI indicates to which eNB the ODU CPE is connected. An operator can have multiple eNBs serving the same cell. eNB ID The operator's cell site ID to which the CPE is connected. A cell site may comprise more than one eNB. Each eNB is given a PCI to identify it. 11 EARFCN The E-UTRA Absolute Radio Frequency Channel Number (band and frequency) within Bandwidth The range of frequencies within the band the CPE may use for wireless communications which the CPE operates with an eNB, expressed in MHz CINR The Channel Signal-to-Interference-plus-Noise Ratio reflects the signal strength of the signal received from the two antennas in the eNB, expressed in decibels (dB) NOTE: Additional SINR values are reported when a transmitting device is using more than two antennas. DL Frequency The frequency, in MHz, being used in the downlink (eNB to CPE). In LTE, the carrier frequency in the uplink and downlink is designated by the EARFCN, which identifies the UL Frequency The frequency, in MHz, that the CPE is using in the uplink (CPE to eNB). In LTE, the carrier frequency in the uplink and downlink is designated by the EARFCN, which identifies the LTE band and carrier frequency. LTE band and carrier frequency. Reference Signal Receiving Quality indicates the quality of the wireless signal Channel Quality indication TXPWR (dBm) Real time UE TX power Roam Roam status Throughput Statistics The current downlink data throughput rate, in Kbps The current uplink data throughput rate, in Kbps The average DL and UL data throughput rates, in Kbps, for this CPE in the last 3 minutes The peak DL and UL data throughput rates, in Kbps, for this CPE in the last 3 minutes The total (sum) DL and UL data throughput rates, in Kbps Access Point Name (gateway) connection to other network devices. At least one APN must be configured to establish the TR-069 connection to the CloudCore or other NMS Enable Indicates if the APN is enabled or disabled MAC Address MAC address of the APN gateway Connection Type Type of network connection IPv4, IPv6, or IPv4v6 address of the APN gateway Domain Name Server IP address MAC Address MAC address of the LAN device, e.g., router, to which the CPE is connected The IP address of the LAN device The subnet mask of the LAN device Numerical ID assigned to each smart device connected through the ODU CPE The name of each smart device connected through the CPE The MAC address of each smart device connected through the CPE The IP address of each device connected through the CPE Amount of time a smart devices IP address has been leased Type of smart device connection 12 RSSI (dBm) RSRQ (dBm) CQI DL UL Average Peak Sum Internet Status APN Number IP Address DNS server LAN Status IP Address Netmask Devices List Index Device Name MAC Address IP Address Lease Time Type 2.6. Network Menu 2.6.1. LAN Settings Enter the Network > LAN DHCP Server enable, IP address, subnet mask, DHCP range, lease time, UPNP enable. Figure 8: DHCP Settings DHCP Static Leases settings can set by the hosts MAC address. Figure 9: DHCP Static Leases 13 2.6.2. WAN Settings 2.6.2.1. NAT Mode The CPE will be worked at NAT mode, and all 8 APNs can be configured by Default router/Data/Mgmt/Voip bear types. Figure 10: WAN Settings 2.6.2.2. Router Mode When selected Router mode, the CPE will worked at router mode, it can dynamic update router tables. Figure 11: Router Mode 2.6.2.3. Tunnel Mode This CPE can support L2TP and GER VPN mode. 14 Figure 12: Tunnel Mode 2.6.2.4. Bridge Mode When the CPE worked at Bridge mode, the WAN ports address will bridge to LAN port, and the LAN port will worked at trunk mode. Figure 13: Bridge Mode 2.6.2.5. Mixed Mode Mixed mode can configured every APN with different mode (e.g. Bridge), this is a professional mode. 15 Figure 14: Mixed Mode 2.6.3. Static Routes Set Static routes of the CPE, it can configure LAN or WAN port routes, Gateway, Destination Network and Route Subnet Mask, in Current Settings, show all activated static routes. Figure 15: Static routes 16 2.6.4. DMZ In technology, the DMZ refers to a firewall between incoming WAN traffic and the LAN to which the CPE is connected. Two basic DMZ methods are (a) using a single firewall, also known as the three-legged model, and (b) using dual firewalls (Figure 36). These architectures can be expanded to create complex architectures depending on the network requirements. Figure 16: DMZ When the LAN has a DMZ/firewall server, you can enable DMZ on the CPE so that packets from the WAN are forwarded to the firewall (Figure 37). Alternatively, you can enable Internet Control Message Protocol

(ICMP) redirect error messages to support Layer 2 multicast features. Figure 17: DMZ Settings 2.6.5. UPnP The Universal Plug & Play (UPnP) function provides a set of networking protocols that allows device-to-device networking on a local network. When UPnP is enabled, devices seamlessly and dynamically discover each others presence on the network and attach to one another and to network services. Often, UPnP is used for streaming media between devices on the network. Go to Security > UPnP to enable the CPE to be searched by other devices (Figure 38). Once enabled, any redirects of traffic will display in the Active UPnP Redirects section of the window. Figure 18: UPnP Settings 17 2.7. LTE Menu 2.7.1. Connection Settings LTE connection settings includes Roaming settings, Default connection settings and Power Scan Option. Figure 19: Connection Settings 2.7.1.1. Roaming setting If set Roam enable, the CPE can access to other PLMN network, else the CPE just can access the network PLMN same with the SIM card. 2.7.1.2. Default connection If set always on, the CPE will automatic access the LTE network after booting, if set manual, the CPE need manual connection to the LTE network. Figure 20: Default Connection Settings 2.7.1.3. Power Scan Option The CPE support two power scan options, the first is First Detected Cell, and the second is the Strongest Cell. 18 Figure 21: Scan mode Settings 2.7.2. Edit APN Profile An Access Point Name (APN) is the name of a gateway between a 3G/4G mobile network and another computer network, frequently the public Internet. Generally, multiple APNs are used for different business flows such as TR-069 management, voice, data, etc., and may support different services and QoS levels for different subscribers. Figure 22: APN Profiles The CPE supports 8 APN configurations. At least one APN (TR-069) must be configured when the CPE/eNB connect to the Baicells CloudCore. In the window (Figure 42) you will select the APN number (1-8), enable it, enter an APN Name, select the type of IP addressing (IPv4, IPv6, or IPv4v6), identify if it is the default gateway, and choose which type of protocol will be supported on it. 2.7.3. PIN Management Use the PIN Management feature if you want to require users to enter a PIN code before they can use the CPE to access the network (Figure 43). Once the PIN is enabled, you will need to remember it if you want to later modify the number. You are limited to 3 tries to enter the correct PIN code before getting locked out. If this happens, contact your service provider (end-users) or Baicells support (service providers). 19 Figure 23: PIN Management 2.7.4. Cell selection The Cell selection determines which frequencies the CPEs routine scan of available frequencies will cover. Scanning is a process of tuning to a specific frequency and measuring the simplest signal quality [e.g., Received Signal Strength Indication (RSSI)]. As part of the cell selection and re-selection process, the CPE performs the scan first and then selects a small number of candidate cells to go through the next step of measuring and evaluating signals to select the best eNB that can serve it. The CPE frequently (milliseconds) performs the scan to ensure it has the best possible connection to the network. Refer Figure 44. Figure 24: Cell selections Select one of the following options:

Full Band (default) All channels in the band. The CPE will routinely scan all channels in the band and all EARFCNs, increasing the time it takes to connect compared to the other modes. The band is dependent on the CPE model. Dedicated EARFCN Specific EARFCNs or frequencies. (Figure 45) The CPE will scan the dedicated EARFCN or frequency list first when it is powered on. If the CPE cannot connect to the LTE network after scanning the list, it will scan other supported bands and frequencies. You can add up to 10 EARFCNs or frequencies. Cell Lock A combination of PCI + EARFCN or frequency. (Figure 46) The CPE is limited to scanning a specific list of eNBs based on both their Physical Cell Identifier (PCI) and EARFCN or frequency. The CPE will scan the list of eNBs with the EARFCN and PCI combination. Using this mode can accelerate network access time. PCI Lock Specific PCIs only. Locks the CPE to a designated PCI or PCI range. (Figure 47) After selecting an option, enter the required information and select ADD. 20 Figure 25: Dedicated EARFCN Figure 26: Cell Lock 21 Figure 27: PCI Only Lock 2.7.5. SIM Lock Settings This feature may be used to lock the SIM card to the operator's network (Figure 48). Each operator has a unique Public Land Mobile Network (PLMN) number. Locking the SIM prohibits the users from accessing another operator's network. Figure 28: Throughput Statistics 2.7.6. MTU Figure 29: MTU Settings This is for setting the MTU of WAN (LTE) port, the range is from 1280 to 1500 Bytes. 22 2.8. Security Menu 2.8.1. IP Filtering When using a firewall server in the local network, invoke this setting to enable or disable the firewall for this CPE (Figure 50). Figure 30: Firewall Basic Settings 23 When enable IP/Port Filtering, then the IP/Port Filter can be set. Figure 31: IP / Port Filtering Settings:

(1) IP/Port Filtering Mode: Blacklist, White list

(2) IP/Port Filtering Log Dropped: enable / disable

(3) Destination IP Address: the destination IP Address of the filter

(4) Source IP Address: the source IP Address of the filter

(5) Protocol: TCP, UDP, TCP/UDP, ICMP, ALL

(6) Destination Port Range: the range of port

(7) Source Port Range: the range of port

(8) Schedule Index: Select box, if can be schedule by APPs

(9) Remarks 2.8.2. IPv6 Filtering When enable IP/Port Filtering, then the IP/Port Filter can be set. Figure 32: IPv6 Filtering Settings:

(1) IPv6 Filtering Mode: Blacklist, White list

(2) IPv6 Filtering Log Dropped: enable / disable

(3) Destination IP Address: the destination IP Address of the filter

(4) Source IP Address: the source IP Address of the filter

(5) Protocol: TCP, UDP, TCP/UDP, ICMPv6, ALL

(6) Destination Port Range: the range of port

(7) Source Port Range: the range of port

(8) Schedule Index: Select box, if can be schedule by APPs

(9) Remarks 2.8.3. MAC Filtering Media Access Control (MAC) Filtering allows you to identify a list of devices either allowed to access or forbidden from accessing the network through the CPE (Figure 53). Select Enable to enable MAC filtering, and then determine whether you will allow or forbid the defined MAC addresses to access the network. Figure 33: MAC Filtering Settings:

(1) MAC Filtering Mode: Blacklist, White list

(2) MAC Filtering Log Dropped: enable / disable 24

(3) MAC Address: the filtering MAC address 2.8.4. URL Filtering The Uniform Resource Location Filter (URL Filter) allows you to define a list of URL addresses users are forbidden from accessing. When you enable the filter, a Settings window appears. Enter the specific URL address users cannot access, as shown in Figure 54. To add more URL addresses, click on ADD. After entering the addresses and saving, the URL(s) you enter will appear in the URL List. Figure 34: URL Filtering Settings:

(1) URL Filtering Mode: Blacklist, White list

(2) URL Filtering Log Dropped: enable / disable

(3) URL: the filtering URL 2.8.5. System Security Figure 35: System Security 25 System Security Profiles, include High, Medium, None and Custom, every profiles will corresponding with a set of System Security Settings. Settings:

(1) Remote Web Login: enable / disable

(2) Remote Telnet: enable / disable

(3) Access Control List: enable / disable

(4) Block Port Scan: enable / disable

(5) Block Syn Flood: enable / disable

(6) SPI Firewall: enable / disable 2.8.6. Connect Limit Connect Limit feature is used to control the number of connections through the UE to a host device, for example, a peer-to-peer file sharing application such as BitTorrent. Such apps require a large amount of bandwidth. By limiting the number of connections to the host device, you can control how much bandwidth each active connection receives. You can configure a Connect Limit for up to 16 host devices. Figure 36: Connect Limit 2.8.7. Schedule This feature is set for a group schedule list, like start from 2020.8.18 to 2020.8.20 as a index of the schedule. Figure 37: Schedule List 26 27 In previous Filter configurations, you can select the schedule index like below figure. Figure 38: Schedule Settings 2.9. NAT Menu 2.9.1. Port Forwarding When NAT mode is enabled as the WAN interface type (section 3.5.2), you can redirect a communication request from one address and port number combination to another. Only the IP address on the WAN side is open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for example, work as an FTP server), port forwarding is required so that all access requests to the external server port from the Internet are redirected to the server on the LAN. To add a port forwarding rule, select the Enable check box and click on ADD LIST (Figure 59). Enter the parameters per the field descriptions in Table 4. Figure 39: Port Forwarding settings Table 4: Port Forwarding Field Name Description WAN Port Range Enter the port number range for the remote device in the format of 1000 to 1500 LAN IP Address Enter the local host IP address. The address must be different from the IP address that is set for the LAN Host Settings parameter, but they must be on the same network segment. LAN Port Protocol Remarks Enter the local port number. Range is 1 to 65,535. Select the type of data protocol, either TCP, UDP, or TCP&UDP 2.9.2. Port Triggering Port Triggering is a configuration option on a router - in this case, the CPE - if it is operating in NAT mode as the WAN interface type (section 3.5.2). When an application uses a trigger port to build a connection, the CPE will forward the data to the forward port. To configure the feature, click on the check box next to Enable and then click on ADD LIST to enter the service type, protocol, trigger port, and forward port (Figure 60). Figure 40: Port Triggering Settings 28 2.9.3. ALG The Application Layer Gateway (ALG) function provides a security component that augments a firewall or the NAT used by the CPE (if WAN Network Mode = NAT). It allows customized NAT traversal filters to be plugged into the gateway to support address and port translation for certain application layer control/data protocols such as SIP, TFTP, PPTP, L2TP and IPSeC. You can enable the different types of application protocols by clicking on the check box next to the protocol name (Figure 61). Figure 41: Throughput Statistics 2.10. System Menu 2.10.1. Account This menu is used to change the login password for the CPE (Figure 62). The password must be 5 to 12 characters. Baicells recommends using a combination of upper- and lower-case letters and numbers. Figure 42: Account 2.10.2. WEB Settings WEB Setting provides the ability to configure and manage the CPE remotely (Figure 63). This is especially helpful when a user calls in for technical assistance. In section 3.3 Login, you used this Web application with the default URL of http://192.168.150.1. Refer to for a description of each field. Figure 43: WEB Settings 29 2.10.3. NTP The operator's network may may use up to 4 Network Time Protocol (NTP) servers to provide correct time-of-day to network devices. In the CPE GUI you can refresh the local time display using the SYNC WITH BROWSER button; select the time zone that the CPE is in; and enable NTP client to use the default or specified NTP servers for synchronization (Figure 64). Figure 44: NTP Settings 2.10.4. TR-069 If your network operates using a TR-069 auto-configuration server (ACS), the ACS will automatically provide the CPE configuration settings. Once you set up both the ACS and the CPE, you do not need to enter any other parameters through the CPE GUI. Use the TR069 sub-menu to enable the TR-069 function for the CPE

(Figure 65). Refer to Figure45, for a description of each field. Figure 45: Throughput Statistics 30 2.10.5. TR-069 Certificate This feature is used to upload the TR-069 certificate. Figure 46: TR-069 Certificate 2.10.6. Restore / Update Use the System > Restore/Update menu to reset the CPE to its factory default settings, to manually update the firmware, or to manually update a module within the firmware - meaning to apply a patch to the current firmware (Figure 67). Caution: Performing a restore or update action will disrupt service. 2.10.6.1. Firmware Update Caution: Do not power off the CPE or disconnect it from the computer during an upgrade. To update (upgrade) the CPE to a different firmware version (Figure 67):

1. Download the image file from the Baicells support website (Baicells > Support > Downloads), and save it to your computer. 2. Under Flash new firmware image, determine if you want to keep the current configuration settings on the CPE . If you do, select the check box next to Keep settings. 3. Click on Choose File to navigate to the new image file on your computer, and then click on FLASH IMAGE to initiate the upgrade. After the upgrade, the CPE will restart automatically running the newer version of code. 2.10.6.2. Restore Factory Settings To initiate a restore action, click on the PERFORM RESET button. The CPE will automatically reset its configuration to the factory default values. Figure 47: Restore & update 31 2.10.7. Diagnosis 2.10.7.1. TCPDump Figure 48: TCPDump Settings Settings:

(1) PC IP Address

(2) PC PORT

(3) Interface: ALL, LTE0PDN0 (APN0) 2.10.7.2. Ping Figure 49: Ping Diagnosis Settings Settings:

(1) IPv4/IPv6: Select the protocol

(2) IP Address/Domain: IP Address or URL

(3) Count: number of ping count

(4) Fragment: yes or no

(5) Packet size: 56~1400 Bytes (non-fragment) 32 2.10.7.3. Trace Figure 50: Trace Diagnosis Settings Settings:

(1) IPv4/IPv6: Select the protocol

(2) IP Address/Domain: IP Address or URL 2.10.7.4. Result Figure 51: Diagnosis results 33 2.10.8. Backup Settings This feature is used to backup the user settings, from the Web-GUI, you can Import / Export the settings. Figure 52: Backup Settings 34 2.10.9. System Log Figure 53: System Log System log is the debug information of the CPE, when select the Setting, it can Export or Clear Logs. Figure 54: System logs 2.10.10. System Messages Use this Web-GUI, you can Export System Message, Collect real-time system information and transfer system message to PC. Figure 55: System Message Settings Figure 56: System Messages 2.11. Reboot Use the Reboot menu to perform a reboot of the CPE, as shown in Figure 77. It can take several minutes for the reboot to complete. After it reboots, the CPE GUI will display the login screen. Caution: The reboot action will disrupt service. Figure 57: Reboot When you click on the Logout menu, you are automatically logged out of the CPE and returned to the login screen (Figure 78). 2.12. Logout Figure 58: Throughput Statistics 35 36 Appendix: Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 37

Model:EG8015G-M11-EUD Baicells pore: Rating: 24V=== 0.5A TM, SNiXXXXXXXXXXXXXXAXXK a a LIMA RS oes IMEI:XXXXXXXXXXXXXXX VIN UA OOO Gserntmes0003 Username:XXXXX LAN MAC:XXXXXXXXXXXX Password:XXXXX FCC ID: 2AG32EG8015GM11EUD Bands: B48

2 S S

Baicells Technologies Co.,Ltd. 45.00 mm

File Name SCH Block Operational Description BOM Tune up Procedure Baicells Technologies Co., Ltd. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID:2AG32 EG8015GM11EUD Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type 1. Schematic 2. Block Diagram;

3. Circuit Description, 4. BOM 5. Tune up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type SHORT-TERM request Sincerely, File Name

(signature):

(printed name): Back Huang Rev 11/20/07

Baicells Technologies Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-6-17 SUBJECT: FCC Application for FCC ID: 2AG32 EG8015GM11EUD To Whom It May Concern:

We, the undersigned, hereby authorize Bruce Zhang at Jianyan Testing Group Shenzhen Co., Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Bruce Zhang on our behalf shall have the same effects as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Baicells Technologies Co., Ltd. Back Huang 13751023286 2021-6-17

\\server\\-old\ 3\EMC\2021\EMC\JYTSZE2103022 LTE Outdoor CPE EG8015G-M11 FCC ID\2.

\letter\POA_Letter_140225.docx