u4G-UE1000 Outdoor CPE Specification Introduction Baicells is a private, high-tech company providing innovative LTE wireless broadband access solutions. The Baicells solutions support fixed wireless access and mobile scenarios. With the vision to connect the unconnected, Baicells has introduced breakthrough technologies to LTE, like moving a complete LTE system to unlicensed spectrum and building it with an IT based architecture. With the Baicells turnkey end-to-end solutions, it becomes much easier to provide wireless internet within everyone's reach at a very low cost. These innovative solutions can be used by mobile operators, broadband access operators, Internet Service Providers (ISP), Mobile Virtual Network Operators (MVNO), governments, and enterprise private networks. The Baicells u4G-UE1000 is a type of LTE-Unlicensed Outdoor Customer Premise Equipment (CPE) working on unlicensed frequency, which provides superior wireless access performance and comprehensive routing capabilities to bring wireless broadband data and voice services to end-users. It converts high-speed LTE FDD signals to WiFi signals on the local area network (LAN). The typical topology of u4G-UE1000 deployment is as follows, which solution provides wireless broadband and wired Ethernet data services for customers. 1 Highlights Supports LTE-FDD frequency bands 46 and self-define frequency. Complies with 3GPP Release 9 CAT4 standards. 1000 Mbps Ethernet interface. Convenient, simple, GUI-based local and remote Web management. Built-in bipolar directional high-gain LTE antenna. TR069 network management protocol. Cell lock, SIM lock, and Pin lock. User-friendly LED indicators. Power supply with standard PoE at/af. Pole mounted or wall mounted. 2 Basic Specifications Item Description UE-Category 3GPP R9, CAT 4 USIM Slot 1.8V/3.0V USIM 2FF Ethernet Port Power Supply Reset Button 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX, PoE at/af Input: Universal range 100V~240V AC Output: standard PoE at/af Tactile button. Long press over 10s to restore the factory settings LED Indicators MIU/LTE/SIM/LAN/PWR/LTE Signal Dimensions 205mm (H) x 155mm (W) x 70mm (D) About 1500 g Weight LTE Specifications Item Description LTE Mode FDD LTE Bands TXRX Peak Rate Customized frequency FDD band DL:5725MHz ~ 5925MHz / UL:5150MHz ~ 5250MHz 1T2R 20MHz: DL: 150Mbps UL: 75Mbps Channel Bandwidth 10MHz/20MHz Modulation UL: QBSK, 16QAM, 64QAM DL: QBSK, 16QAM, 64QAM Receive Sensitivity
-93dBm @ QPSK, 20MHz, 25C 3 MAX Output Power 26dBm (2)/TX ANT Antenna Type Internal directional antenna Antenna Gain 14dBi1@5150MHz ~5925MHz, 2 Ports Polarization Antenna Efficiency Isolation VSWR 45
>75%
-15dB 2 Horizontal Beam Width (3dB) 333@5150MHz ~5925MHz, 2 Ports Vertical Beam Width (3dB) 223@5150MHz ~5925MHz, 2 Ports SW Specifications Item Description Language Support English/Chinese Network Mode NAT/Router/Bridge IP Protocol IPv4/IPv6 SIM Management PIN Management, SIM Lock Network Connection Management Auto/Manual LTE Scan Mode Full band scan, Frequency Lock, PCI Lock WLAN VPN NAT WiFi for CPE Alignment L2TP L2/L3 GRE L2/L3 Port forwarding DMZ ALG Port Trigger 4 Firewall IP/MAC/URL Filter Access Control Block Port Scanner / SYN Flood SPI Filter Network Management TR069 Diagnostics Statistics Maintenance System Log LTE Status/Connection Time/System Up Time TCPDump Ping Trace route Device Status DHCP Client List WiFi Station List Firewall Status LTE Status Date & Time setting Reboot Restore factory settings Restore / Back up configuration file Firmware upgrade locally/OTA (over the air) Operating Log Run-time Log Filter/Select/Display/Export Log Antenna Select N/A Environmental Specifications Item Description Operating Temperature
-40C to 55C Storage Temperature
-40C to 70C Operating Humidity 5% to 95%
IP Level IP65 5 Model List Models Description u4G-UE1000 u4G-UE1000( LTE CPE ODU, Self-defined FDD, CAT4, 1T2R, 1GE, PoE at/af, IP65) Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 40 cm between the radiator
& your body. 6