User manual for AW-AU397 module integration 1 Purpose The purpose of this document is to provide information on how to install the AW-AU397 module in B&O products. The AW-AU397 W-LAN module is only intended for integration into end host products by B&O authorised personnel only. Incorrect integration or use may infringe compliance rule meaning recertification is required. 2 Module description The module is an IEEE 802.11a/b/g/n 2X2 MIMO WLAN & Bluetooth module based on a Marvell chip. The module is designed to be plugged into a Mini PCI-E 52P connector, which contains all the interfaces and power connection. Additional the module has two UFL antenna connectors. See picture below. Integration in B&O products 3 The AW-AU397 module will be integrated in both audio and video products from B&O. A similar Mini PCI-E connector is used as interface and the antennas inside the product are connected to the UFL connectors at the module. 3.1 Module Integration Details Use the respective B&O build/assembly instructions for mounting and connecting the module into each B&O product type. This will ensure correct working of the module and will ensure it will not be collocated with any other transmitter/antenna if these instructions are followed. 3.2 Audio Devices In B&O audio products the AW-AU397 module can be installed in two different ways:
1. Stand-alone integration 2. Audio Streaming Engine mounted An example of stand-alone integration is shown in the following photos with the AW-AU397 module integrated in the BeoSound Moment end product:
An example of the Audio Streaming Engine integration is shown in the following photo:
3.3 Audio Device Antennas The AW-WU397 module when integrated into Audio Devices will use the Tyco Puck antenna, part no.1513472-5, with a frequency range of 2,400 - 2,483.5 MHz & 5,150-5,875 MHz and peak gain of +3 dBi. If other radio systems are integrated in the product, it is required to keep minimum 20cm separation distance between any antenna from other radios and each of the antennas connected to AW-WU397. The module must not be integrated in portable devices to be used in direct contact with the body of the user or within 20cm of the body of the user under normal operating conditions. 3.4 Video Devices In Video Devices the AW-AU397 module will be mounted on a small interface board with a cable connection to the Video Engine. The interface board provides good flexibility for placing the module in an optimum position keeping antenna cables short. See picture. 3.4.1 Video Device Antenna The AW-AU397 module when integrated into video products will use the B&O BO AirWire antenna with a frequency range of 2,400-2,483.5 MHz & 5,150-5,875 MHz and a peak gain of +4.2 dBi. If other radio systems are integrated in the product, it is required to keep minimum 20cm separation distance between any antenna from other radios and each of the antennas connected to AW-WU397. The module must not be integrated in portable devices to be used in direct contact with the body of the user or within 20cm of the body of the user under normal operating conditions. 4 End Product Labelling A label is to be fitted to the exterior of all products containing the AW-AU397 module. The label must include the words Contains FCC ID: TTUAW-AU397 (for FCC) or Contains IC:
3775B-AWAU397 (for IC). Examples of B&O Audio and Video product labels and placement locations are in the following sections. 4.1 BeoSound Moment:
4.1.1 Label 4.1.2 Location 4.2 BeoVision Avant:
4.2.1 Label 4.2.2 Location FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate. This module must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the antenna & users body. In the United States, operation on channels 36-48 in the 5150-5250 MHz band is restricted to indoor-use only. If the FCC ID of the module is not visible when installed in the intended host equipment, then a permanently attached or marked label must be displayed on the exterior of the host equipment referring to the module FCC ID. Industry Canada Compliance This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (IC ID: 3775B-AWAU397) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. 1) (Puck) Tyco; Part No. 1513472-5; Frequency Range: 2,400 - 2,483.5 MHz & 5,150
- 5,875 MHz; Gain (Max) +3 dBi, 2) (V100) B&O; Part No. BO AirWire; Frequency Range: 2,400 - 2,483.5 MHz &
5,150 - 5,875 MHz; Gain (Max) +4.2 dBi Please note that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250- 5350 MHz and 5650-5850 MHz and these radars can cause interference and/or damage to LE-LAN (License Exempt Local Area Network) devices. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the antenna and your body. Cet appareil est conforme au(x) standard(s) RSS exempt(s) de licence dIndustrie Canada. Son fonctionnement est sujet aux deux conditions suivantes:
(1) cet appareil ne doit pas occasionner dinterfrence et (2) cet appareil doit supporter toutes les interfrences, y compris celles qui pourraient provoquer un mauvais fonctionnement de cet appareil. Compte tenu des rgles mises en place par Industrie Canada, cet metteur radio ne peut fonctionner qu laide dune antenne dont le type et le gain maximal ont t approuvs par Industrie Canada. Afin de rduire le risque dinterfrence radio avec les autres utilisateurs, le type dantenne et son gain doivent de prfrence tre choisis de manire ce que la puissance isotrope rayonne quivalente (PIRE) ne dpassent pas le niveau ncessaire une communication efficace. Cet metteur radio (IC ID: 3775B- AWAU397) a t approuv par Industrie Canada dans le cadre dune utilisation avec les types dantennes repris ci-aprs, avec le gain maximum autoris et limpdance requise indiqus au regard de chaque type dantenne. Lutilisation de types dantennes non repris dans cette liste ou dont le gain est suprieur celui indiqu pour leur type est strictement interdite en conjonction avec cet appareil. 1) (Puck) Tyco; Part No. 1513472-5; Frequency Range: 2,400 - 2,483.5 MHz & 5,150
- 5,875 MHz; Gain (Max) +3 dBi, 2) (V100) B&O; Part No. BO AirWire; Frequency Range: 2,400 - 2,483.5 MHz &
5,150 - 5,875 MHz; Gain (Max) +4.2 dBi Please note that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250- 5350 MHz and 5650-5850 MHz and these radars can cause interference and/or damage to LE-LAN (License Exempt Local Area Network) devices. Cet appareil est conforme aux limitations de la norme IC RSS-102 concernant lexposition aux radiations dans un environnement non contrl. Cet appareil doit tre install et utilis avec une distance minimale de 20 cm entre lantenne et le corps de lutilisateur.