H S I L G N E PANTHER SERIES Push plate with integrated 900 MHz wireless transmitter
(US version) 4 5 6 7 8 DESCRIPTION 1 2 3 1. Hex Key 2. Housing Assembly 3. Faceplate 4. Locking Tab 5. Mounting Bracket 6. Battery Enclosure 7. Mounting Keys 8. Mounting Holes 6 INCH ROUND, 900 MHz:
10EMR61-900 - logo & text 10EMR6-900 - text only 10EMR6L-900 - logo only 4.75 INCH ROUND, 900 MHz:
10EMR4751-900 - logo & text 10EMR475-900 - text only 10EMR475L-900 - logo only 4.75 INCH SQUARE, 900 MHz:
10EMS4751-900 - logo & text 10EMS475-900 - text only 10EMS475L-900 - logo only 75.5172.06 PANTHER SERIES 20160517 75.5172.06 PANTHER SERIES 20160517 Page 1 of 4 Page 1 of 4 The device should not be used for purposes other than its intended use. All other uses cannot be guaranteed by the manufacturer of the sensor. The installer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system in compliance with applicable national and international regulations and standards on door safety. The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor. INSTALLATION 1 2 Install Mounting Bracket using at least two (2) #8 countersunk head screws. Any mounting holes may be used. Observe THIS END UP. Align Housing Assembly onto Mounting Keys and slide down until Locking Tab engages. To remove, press Locking Tab and slide up. NOTES:
1. For added security, additional screws may be installed through Housing Assembly and Mounting Bracket during Step 2. 2. Ensure spring clips click during Faceplate installation. It may be necessary to rotate Faceplate for proper alignment. 3 Insert Faceplate into Housing Assembly and use Hex Key to engage spring clips on the top and bottom of Housing Assembly. To remove, use Hex Key to disengage spring clips. Page 2 of 4 Page 2 of 4 75.5172.06 PANTHER SERIES 20160517 75.5172.06 PANTHER SERIES 20160517 SETUP 1 BATTERY REPLACEMENT 1 To program the 900 MHz wireless receiver (sold separately), please refer to the appropriate Users Guide:
900 MHz - 75.5786 900 MHz Panther series must use a 900 MHz receiver. Remove four (4) screws on Battery Enclosure. 900 MHz versions - two (2) CR2032 DO NOT OVER TIGHTEN SCREWS DURING REASSEMBLY. THIS MAY CAUSE CONSTANT TRANSMITTER ACTIVATION. TROUBLESHOOTING No activation Receiver not programmed Setup transmitter Constant activation Receiver improperly wired Verify power and activation connection Dead battery Replace battery Battery Housing screws too tight Activation connected to NC of door control Receiver set to Toggle Mode Loosen Battery Housing screws Connect to NO Set receiver to Pulse Mode 75.5172.06 PANTHER SERIES 20160517 75.5172.06 PANTHER SERIES 20160517 Page 3 of 4 Page 3 of 4 TECHNICAL SPECIFICATIONS I G N T N R P I R O L O C R O F D E N G S E D I
-
E S U R E H T R U F R O F P E E K E S A E L P I 7 1 5 0 6 1 0 2 S E R E S R E H T N A P 6 0 2 7 1 5 5 7
|
s n o i t c u r t s n
. I l a n g i r i
|
O A E B Dimensions Weight Material 6 ROUND - 6.33 diameter, 1.45 depth 4.75 ROUND - 5.12 diameter, 1.42 depth 4.75 SQUARE - 5.12 height, 5.12 width, 1.42 depth 6 ROUND - 1.2 lbs 4.75 ROUND - 1.14 lbs 4.75 SQUARE - 1.04 lbs FACEPLATE - stainless steel HOUSING - ABS plastic Transmitter Frequency 900 MHz Power Mounting Certification Temperature 900 MHz versions - two (2) CR2032 Surface mount only FCC, IC 14 F - 131 F (-10 C - 55 C) Enclosure Rating NEMA 4 Specifications are subject to change without prior notice. All values measured in specific conditions. FCC / IC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by BEA Incorporated could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC ID: 2ABWS-10TD900PTRI IC: 4680-10TD900PTRI MODEL: 10EMR6-900 MODEL: 10EMR475-900 MODEL: 10EMS475-900 MODEL: 10EMR6L-900 MODEL: 10EMR475L-900 MODEL: 10EMS475L-900 MODEL: 10EMR61-900 MODEL: 10EMR4751-900 MODEL: 10EMS4751-900 ANSI / AAADM Compliance Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the minimum inspection guidelines provided by AAADM. Provide each equipment owner with an owners manual that includes a daily safety checklist and contains, at a minimum, the information recommended by AAADM. Offer an information session with the equipment owner explaining how to perform daily inspections and point out the location of power/operation switches to disable the equipment if a compliance issue is noted. The equipment should be inspected annually in accordance with the minimum inspection guidelines. A safety check that includes, at a minimum, the items listed on the safety information label must be performed during each service call. If you are not an AAADM certied inspector, BEA strongly recommends you have an AAADM certied inspector perform an AAADM inspection and place a valid inspection sticker below the safety information label prior to putting the equipment into operation. Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: Tech_Services@beainc.com | Tech Docs: www.beasensors.com Page 4 of 4 Page 4 of 4 75.5172.06 PANTHER SERIES 20160517 75.5172.06 PANTHER SERIES 20160517