TROUBLESHOOTING ace) dy tT Tela} Solutions The batteries inside the radio controller are too weak. Replace with new Alkaline batteries. There is a weak or low reception to the radio controls. The batteries inside the vehicle are Replace with new batteries inside too weak. the vehicle. Running Problems Turn the On/Off switch of the vehicle Objects obstruct the movement of the to OFF position. Remove obstructions wheels. by using tweezers and carefully pull out Operating Problems tangles. The motorcycle was driven on rough It is recommended to run the vehicle terrain and something get caught in the on a flat and hard surface or pavement. wheels. The vehicle does not respond to the Try running it on another location. radio control. Some other equipment using the same The radio controls frequency is disrupted | radio wave could disrupt transmission. by something around the environment. Either run the vehicle in another location or turn off the other equipment. PLEASE NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
+ Reorient or relocate the receiving antenna.
+ Increase the separation between the equipment and receiver.
+ Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
+ Consult the dealer or an experienced radio/TV technician for help. MADE IN CHINA CONTENT LIST To prevent damage, the contents of the package listed are properly packed and may be out of plain sight. Please remove all contents in packaging. 4 CAUTION:
DO NOT MODIFY TOY IN ANY WAY. ADULT SUPERVISION IS ADVISED!
CONTROLLER MOTOCROSS BIKE GETTING TO KNOW YOUR MOTOCROSS BIKE Diagram 1 Fully Detailed Rider LED Power Forward/Brake Indicator Control Front Wheel Steering Spokes Rear Wheel Suspension , Left/Right Control Battery Battery . On/Off Switch Compartment Compartment BATTERY INSTALLATION Diagram 2 1) Make sure the motorcycle is in OFF position. 2) Using a crosshead screwdriver, unscrew the battery compartment cover located at the bottom. 3) Insert 4 AAA batteries (not included) into the motorcycle, according to the correct polarities (as shown). 4) Replace the battery cover. Tighten screw. DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC), O RECHARGEABLE BATTERIES. DO NOT MIX OLD AND NEW BATTERIES. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK. Diagram 3 1) Make sure the controller is in OFF position. 2) Push and slide down the battery compartment cover located in the back. 3) Insert 2 AA batteries (not included) into the controller, according to the correct polarities (as shown). 4) Replace the battery cover. PLEASE NOTE:
A) Make sure the batteries are inserted correctly (+ or -) into the controller. B) If the vehicle does not respond properly, please replace the Alkaline batteries in the controller or recharge batteries. ITEM NO. B1005 5+
MADE IN CHINA MOTOCROSS BIKE Radio Control INSTRUCTION MANUAL IF MOTORCYCLE DOES NOT RESPOND PROPERLY, PLEASE REPLACE
*IMPORTANT: tne Batteries IN VEHICLE (4-AA NOT INCLUDED) AND CONTROLLER
(2-AA NOT INCLUDED).
** NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC), OR RECHARGEABLE BATTERIES. REQUIRES 4 AAA BATTERIES IN VEHICLE AND 2 AA BATTERIES DO NOT MIX OLD AND NEW IN CONTROLLER. BATTERIES. COLORS AND DECORATIONS MAY DO NOT DISPOSE OF BATTERIES eee IN FIRE, BATTERIES MAY . EXPLODE OR LEAK. or Wittelik Warning:
. Make sure you always use new or fully charged batteries . Non-rechargeable batteries are not to be recharged. in the controller. Rechargeable batteries are only to be charged under adult
. Do not operate the motorcycle if it becomes damaged in supervision. any way. Rechargeable batteries are to be removed from the toy
. Check that the infrared signal from the controller is making before being charged. a connection with the vehicle before operating. Different types of batteries or new and used batteries are
|. Try not to crash the motorcycle as it may cause damage. not to be mixed. Check that the area is clear of any obstacles before you . Batteries are to be inserted with the correct polarity. operate. Exhausted batteries are to be removed from the toy. Adult supervision is always recommended. The supply terminals are not to be short-circuited. Never operate near animals. Keep motorcycle away from your fingers, hair, eyes and other body parts. Stay away from obstacles and electrical hazards. USING YOUR MOTOCROSS BIKE Diagram 4 Using the Motorcycle:
1) Turn the On/Off switch on the motorcycle :
to the ON position. Left/Right 2) Turn the On/Off switch on the controller to the ON position. 3) Place the motorcycle on the ground and use the controller to maneuver. ON 4) If the motorcycle does not respond, turn both a motorcycle and controller switch to OFF, then as repeat above steps 1 and 2. 5) When done operating, return both motorcycle and controller to the OFF position. 6) When not being used for an extended amount of time, remove the batteries from both the motorcyle and controller. DANGER!
NEVER TOUCH THE WHEELS WHEN THEY ARE TURNING. NEVER INSERT ANY SHARP OBJECTS, PINS OR SCREWS INTO THE VEHICLE AS THIS MAY PUNCTURE THE MOTOR OR THE BATTERY!
NOTE:
Operating multiple RCs with the same frequency in close proximity will cause interference and poor performance. Works best away from electrical hazards and large obstacles. Do not put objects or fingers near the front or rear of the wheels while it is turning. Vehicle may not run properly on rough terrain. Make sure objects do not get obstructed in the wheels. Avoid hard crashes. Never give the vehicle or controller to any child under the age of 3, as it contains small parts. When not in use, remove batteries from compartments (motorcycle and controller). Normal working distance is about 80 feet (24 meters).