R-
F MASSAG PL UG SY STE M Users Manual MO BM1 E D E L
1 Unpacking & Assembling Your Base:
Section #1 1.Remove the plastic covering from the batteries. Place the (4) AAA batteries in the remote. Verify batteries are properly installed. Push any button on the remote and the background will illuminate when working properly. 2.To synchronize your remote to the control box mounted on the base.Press the CODE button on the control-box, LED light will be on for 30 seconds, within the allotted time, press the SET button on the remote until the LED light goes off, this means code-setting between the remote and the controller box was successful. 3. Depress <Head> Up Button on your remote to verify the base operates and the remote is communicating with the control box. If base does NOT operate refer-
ence Synchronizing Your Remote to the Controller Box in Section 5. 4. Depress ON/OFF Massage buttons to turn massage motors on. Depress Head Up and Foot Up Buttons to verify massage motors are operating properly. Page 1 Section #2 ADVISORY IMPORTANT INFORMATION READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT This BetterRest Adjustable Powered Sleep System has been designed with features to assure comfort and safety when operated properly. lation this Device may not cause harmful interference, F CC Regu This device complles with Part 15 of the FCC rules. two conditions:
(1) interference received, ELECTRICAL GROUNDING This product is equipped with a polarized, grounded electrical power cord. The power cord will only fit into a grounded, electrical outlet. including interference that M ay cause undesired opration.. O peration is subj ect to the following and( 2) this device M ust accept any WARRANTY WARNING Do not open any control boxes, motors or hand control devices (with the exception of the hand control). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of adjustable bed parts must be performed by authorized personnel. LUBRICATION This product is designed to be maintenance free. The lift motors are permanently lubricated and sealed-no additional lubrication is required. Do not apply lubricant to lift motor. PRODUCT RATINGS The bed lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motors do not operate any more than three (3) minutes over a thirty (30) minute period, or approximately 18% duty cycle. NOTE: Massage equipped beds are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty. WARNING The manufacturer is not responsible for any r ad mod eifications to this eq u the eq uipment ipment.such mod i o or TV d by unauthoriz ed ification could void the user' s authority to operate interference c ause Page 2 Section #2 ADVISORY IMPORTANT INFORMATION For best performance, consumers should enter and exit the adjustable bed with the bed in the flat (horizontal) position. DO NOT SIT ON THE HEAD OR FOOT SECTIONS WHILE IN THE RAISED POSITION. ELECTRICAL COMPONENTS BetterRest Adjustable Powered Sleep System electrical components are rated for 110/120 voltage, 50-60 Hz. SMALL CHILDREN/ PETS WARNING After the foundation is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the bed. Children should not operate this bed without adult supervision. Page 3 Section #3 PRODUCT SPECIFICATIONS MAIN POWER SUPPLY 110/120v A/C, 50-60 HZ MOTOR OPERATING VOLTAGE 24 v D/C with 50 VA transformer with 30 minute cut off MOTOR DUTY CYCLE 18% maximum operation 3 minutes MASSAGE MOTORS Two 24v, 2 variable DC motors, with 30 minute auto shut off REMOTE CONTROL 4 x AAA 1.5v batteries BATTERY BACKUP 1 x 9v battery Page 4 Remote Control Operation:
Section #4 Page 5 Section #4 Remote Control Operation Contd:
Pos 1 (Key 1): is a Pre Set Position for Back only. Pos 2 (Key 2): is a Pre Set Position for Back and Foot only. Pos 3 (Key 3): is a Pre Set Position for Foot only. The Set Button (Key 4) has Two main functions. It is used to program Any Remote Hand control to the Black Box by pressing the Key S (Key 4) and simultaneously pressing the CODE button (Explained in detail Synchronizing Your Remote) on the controller box till the LED light on the box goes out. The user can PRESS ONE Hand controls S button and have TWO CODE buttons simultaneously pressed on TWO Black Boxes (Wait till the LED LIGHTS go OUT) and the user can Now use One hand control to operate 2 BetterRest beds simultaneously (no extra cords are needed for 2 Bed Base to operate with ONE hand control). The remote control is now set to operate ONE or TWO beds and massage. The Set Button is also used to memorize or save your favorite position or massage intensity. After finding your favorite setting using the Back and Foot angle, press the Set Button until you hear 2 Beeps. Then press the LEVEL (Key 7) and the bed goes to its flat position and the On/Off key of both massage. To find your chosen position with or without massage, simply press the PROGRAM Key P (Key 8) and your favorite position with or without massage will be attained. Key 5 (HEAD) and Key 6 (FOOT) are for independent adjusting to your chosen angle or degree. The Key 9 and 10 are for independent massage intensity by pressing the upper part of the Key 9 and 10 the massage becomes more intense and by pressing the lowerpart of the keys the massage becomes less intense. The massage motors are TURNED ON/OFF by pressing the buttons ON/OFF (Keys 11 and 12). User Defined Settings:
Keys 13, 14 and 15 are three Pre-Set massage programs with different massage wave motion. Massage Mode Massage Mode Massage Mode Program 1 Program 2 Program 3 Note: If massage is utilized in FLAT position and MEMORY button utilized to save settings then the bed also memorizes the FLAT position. TO UNLOCK it press LEVEL button. Page 6 Synchronizing Your Remote To The Controller Box:
Section #5 Press the CODE button on the control-box, LED light will be on for 30 seconds, within the allotted time, press the SET button on the remote until the LED light goes off, this means code-setting between the remote and the controller box was successful. Page 7 Section #6 Warranty Claims In the event of a warranty issue, please call (800) 432-2225 FOR YOUR RECORDS Jobri, LLC strongly recommends that you register your product and keep your receipt in a safe place with this manual. DATE OF PURCHASE SERIAL NUMBER PLACE OF PURCHASE Page 8