Specications Name: ONEBOT Educational Robot Kit Model: AIQIEDU#01 Ages: 10+
Input voltage: 9V Input current: 1.0A Important Safeguards Wireless connectivity: Bluetooth 4.2 Main materials: ABSPC Dimensions: 60030065mm Gross weight: 1850g Do not dismantle the intelligent brick, device, or baery cartridge. Remove the baery from the baery cartridge if the product will not be used for a longtime. Do not expose the product to heat re, or ambient temperatures above 60C. Do not short circuit. Do not crush or puncture. Children aged 10-14 should only use this product under adult supervision. Regularly check for damage to the electric cord, plugs, casing or other parts. If there is damage, do not use the product until it has been repaired. CHOKING HAZARD - Small parts. Not for children under 3 years. Manufactured by: BeingAIQITechnologyCo.,LTD. Address: Room.D1203,The11thoor,BlockD,No.9Shangdi3rdSt.,HaidianDistrict, Being,100085,China. Thanks for choosing ONEBOT Educational Robot Kit Declaration of Conformity Troubleshooting WEEE Disposal and Recycling Information Correct Disposal of this product. This marking indicates that this product should not be disposal with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsible to promote the sustainable reuse of materials resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Aention that changes or modication not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Problem Possible Cause Solution The intelligent brick light remains o. Is the controller switch turned on?
Turn on the controller switch. Is the baery out of the power?
Replace with new baeries. Bluetooth connection failed. Are there baeries installed?
Install baeries. Is the controller switch turned on?
Turn on the controller switch. Is the baery out of the power?
Replace with new baeries. Is your phone's Bluetooth o?
Turn on your phones Bluetooth. The device cannot be discovered. Is there a good connection between the device and intelligent brick?
Reconnect the intelligent brick and device. The handle doesnt control the device. The program does not execute. Has the Bluetooth been disconnected?
Connect again via Bluetooth. Is there a good connection between the device and intelligent brick?
Reconnect the intelligent brick and device. Has the Bluetooth been disconnected?
Have you tapped the Start buon in the app?
Connect again via Bluetooth. Tap the Start buon. Is the baery out of the power?
Replace with new baeries. The rmware update has failed. Are the sensor and control board connected Reconnect the sensor to the control board Has the Bluetooth been disconnected?
Connect again via Bluetooth. Press the intelligent bricks reset buon to restore factory seings should the above solutions prove ineective. Hereby,[Being AIQI Technology Co., Ltd. ] declares that the radio equipment type[designation of type of radio equipment] is in compliance withDirective 2014/53/EU. FCC ID: 2ALJ6-AIQIEDU ONEBOT EDUCATIONAL ROBOT KIT User Manual Read this manual carefully before use, and retain it for future reference Accessories Product Overview 1. Controller Master Block Packs ntelligent Brick 2 Item List ONEBOT EDUCATIONAL ROBOT KIT User Manual Read this manual carefully before use, and retain it for future reference User Manual Storage Box Cardboard 7 1 2 3 4 Microphone Indicator light POWER Loudspeaker 1 3 5 6 4 8 5 6 Motor interface/Data expansion port Assembling hole Reset 7 8 Baery Cover 2. For detailed instructions on how to use electronic components in the Item List, see the ONEBOT APP. Installing the app 3. Baery Installation ONEBOT Educational Robot Kit requires six AA baeries. Follow the steps below to install:
The installing and uninstalling of baeries shall always be done by an adult. Open the baery cartridge lid by pushing in the direction indicated on the lid. Install the six AA baeries in accordance with the positive and negative polarity markings on the boom of the baery cartridge and baeries. Place the baery lid correctly on the baery cartridge. Check that the location hole is correctly aligned. This product requires six AA baeries. Non-rechargeable baeries cannot be recharged. Rechargeable baeries must be charged under adult supervision. Rechargeable baeries must be removed from the product before recharging. Do not use dierent manufacturers or new/old baeries together. Do not allow the power supply to short circuit the device. Baeries must be placed according to their correct polarity. Remove exhausted baeries from the product. Assembling 1. Before you start Ensure that you have organized your Blocks into the Storage Box. 2. Build with blocks Please refer to the apps Dynamic Build Manual for more information on building with the ONEBOT Educational Robot Kit. 3. Inspect your robot Make sure you have installed baeries in the controller. Make sure you followed the building instruction. Make sure the controller switch is on and the indicator light of the controller is on. 1. Search for "ONEBOT" in the App Store or Google Play to download ONEBOT app.
( For a beer operating experience, its recommended to use tablet devices to install the app.) 2. Connecting to the ONEBOT Educational Robot Kit Properly install the baery in the baery case and turn on the switch, open the ONEBOT APP, turn on the Bluetooth function, click the Bluetooth icon buon in the upper le corner of the main screen, search for Bluetooth devices, select device, and connect to the ONEBOT Educational Robot Kit. Bluetooth Bluetooth connection status Seings Bluetooth is not connected Programming Sensor User Guide handle