Manual Product Description The product is a Biometric Recognition Device system which contains Identification Terminal,Interface module(optional),and the gate control part. The system is an intelligent channel management and control device with integrates QR code recognition, license reading and face recognition functions. It is based on TCP/IP network communication and uses synchronous data backup with the SaaS platform. The system is an intelligent terminal device based on block-and-pass behavior which combines with face recognition technology to achieve personnel identification and passage control so as to enhance safety management. Installation instructions 1.Remove the speed gate door cover. 2.Remove the base bracket inside the speed gate door cover, tighten the identification terminal to the base with screws (M4*9.5), (a rubber gasket can be used to adjust the gap between the base and the cover), then put the base bracket back in place. 3.Fix the base to the base bracket with screws (M4*9.5), adjust all the screws after adjusting the identification terminal to the ideal angle, ensure identification end fixed to the base bracket. 4.Install the interface module into the reserved installation position in the speed gate door with screws (M3*6). 5.Connect the two cables (Cable A and Cable B) from the identification terminal to the corresponding interfaces on the interface board. Note1Please attention insert direction of the Cable A ,refer to the "Figure 2". 6.Reinstall the speed gate cover. All operations must be finished by the professional installers. Identification Terminal The speed gate cover Installation diagram Figure 2 Interface module(optional) Rubber gasket Base bracket Base M4*9.5 screw M4*9.5 screw Base bracket fixing nut Cable B Non-standard packaging accessories Cable A
(IBup) Dimensions (Unitmm) 76 119 Figure 1 8 4 3 30 Figure 3 Rotatable Angle46~77 Figure 4 6 25 Port Description Figure 5 Cable B TTL USB5 Cable A GND RS485_A RS485_B GND RS232_RX RS232_TX
+12VDC IN
+
_ Audio LAN USB1 USB2 USB3 l R e a y _ N O l R e a y _ N C l R e a y _ C O M G N D G N D W G _ D 1 _ I W G _ D 0 _ I W G _ D 1 _ O W G _ D 0 _ O USB4 Specification Product Number Living Security Qr code Scanning Multi-touch OS Camera Display Operating temperature Relative Humidity Power Cord Rating Dimensions BRD-AG-SD1 Support Support(optional) Support Android 7.0 Professional Wide-angle Dual Camera (Visible Light & Infrared) 8.0inch Touch LCD800*1280
-10 ~ 55 5%-95%(Non-condensing) DC 12V 3A 119*76*348mm Communication Method Physical Interface Power On Wi-Fi 2.4 GHz/5 GHz5150MHz-5250MHz;
5725MHz-5850MHz, IEEE 802.11a/g/b/nIEEE 802.11ac BT4.1+BLE Support Bluetooth Ethernet Wiegand TX*1Wiegand RX*1Relay*1RS232*1RS485*1 USB2.0*3RJ45*1Audio*1 Support FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 317-00487-01 2018 Beijing Beebox Technology Co.,Ltd. all rights reserved. Printed in China. Add: 23A,JingYuan Arts Center, No.3 GuangQu Road,ChaoYang District,Beijing,100124