Mi Action Camera 4K User Manual Read this manual carefully before use, and keep it properly for future reference. 4K 1. Package Contents Mi Action Camera 4K x 1 Battery x 1 Mi Action Camera Battery 4K USB cable x 1 User manual x 1 2. Product Overview 2 1 3 4 5 6 7 8 9 1 2 3 Lens Front Indicator Function Button 4 5 6 Top Indicator Microphone Speaker 7 8 9 Port Protective Cover Micro-USB Port Microphone 13 12 11 10 14 15 10 11 Touch Screen Lock Button 12 13 Battery Cover 1/4-inch Thread Hole 14 15 Battery MicroSD Card Slot 3. Install and Disassemble a. Remove the battery cover (as shown in the gure), align the battery pins with the direction of the lens, and insert the battery. To remove the battery, gently pull the handle bar on the battery. b. Keep the label side of the MicroSD card towards the back of the camera body, and insert the card into the card slot. To remove the MicroSD card, gently press the top edge of the card to eject it from the slot. Do not damage the handle bar. Press the battery cover lock button and push the battery cover outwards. MicroSD Card 4. Battery Charging a. You can use a 5V 1A power adapter, PC, or mobile power bank to charge the camera via a data cable. It is recommended to turn off the camera during charging. b. The front indicator is solid red while charging, and turns off automatically when the battery is fully charged. Red Off Note:
It is recommended to remove the battery if you connect the camera to a power supply for a prolonged period during use. 5. Operating Instructions a. Power-on/Power-off Power-on: Press and hold the function button for about 3 seconds, followed by a power-on sound. Power-off: Press and hold the function button for about 3 seconds, followed by a power-off sound. b. Photo Select the photo mode, and press the function button to take photos. c. Video Select the video mode, and press the function button to start the recording. Press the function button again to stop the recording. Function button Note:
When shooting a 4K-video, it is recommended to use a main brand UHS-3 MicroSD card with a capacity not less than 16 GB. Video les are stored in the FAT32 format. The maximum size of a single video le is 4 GB. A video le exceeding 4GB will be fragmented for storage. d. Operating screen The preview page is displayed after the camera is powered on (in screen lock mode, you can double-tap the screen or press the function button to wake up the camera). Camera setup On the preview page, slide down to enter setup page. Slide the screen in the reverse direction or press the function button to return to the preview page. Wi-Fi setup / Bluetooth device connection Tap to enable or disable the Wi-Fi function. Select the bluetooth device in the setup page, and connect according to the prompt Mode selection On the preview page, slide rightward to enter mode selection page. Slide the screen in the reverse direction or press the function button to return to the preview page. Media library On the preview page, slide leftward to enter media library preview page. Slide the screen in the reverse direction or press the function button to return to the preview page. Note: A MicroSD card needs to be installed. photo Time Lapse Burst Photos Video Slow Motion 6. Quick Setup Control your device and interact it with other smart home devices in Mi Home App. a. Download Mi Home App Scan the QR code or go to App store to download and install Mi Home App. b. Add and connect a Mi Action Camera 4K Tap "My devices" in Mi Home App, select "+" on the upper right, and select Mi Action Camera 4K. Install the plug-in and follow prompts to add the device. Open the Mi Action Camera 4K plug-in. Turn on Mi Action Camera 4K and slide down to access the shortcut menu page. Enable the Wi-Fi function. Tap "Connect" on the App, and follow the instructions to complete the Wi-Fi connection. Note:
The GPS must be activated for some certain phones when searching for the Mi Action Camera 4K via Wi-Fi. After the App is connected to the camera successfully, Android phones disconnect the Internet and a prompt indicating no Internet connection is displayed on some certain phones. In this case, choose to maintain the current connection. To upgrade the camera rmware, you need to maintain the phone's connection to the Internet. 7. Indicator Status Status Front indicator Front/Top indicator Front indicator On Slow blinking Fast blinking red Description Powered on indicator Photo shooting/Video recording No card/Card error Front/Top indicator Fast blinking alternately Upgrading Note: When the front indicator is blue, the unit is fully charged; when is yellow, the battery is adequate; when is red, the battery is low. 8. Specications Product name: Mi Action Camera 4K Dimensions: 71.5 mm x 42.7 mm x 29.5 mm Net weight: 99 g (including battery) Operating temperature: 0~45 Storage temperature: -20~60 Wireless connections: Wi-Fi IEEE 802.11b/g/n Maximum photo resolution: 3840 x 2160 Maximum video resolution: 3840 x 2160p at 30 fps Model: YDXJ01FM Aperture: F2.8 Focal length: 3.2 mm Wide angle: 145 Bluetooth: Bluetooth 4.1 Recording: dual microphone MicroSD card: maximum 64GB Screen: 2.4-inch touch screen 9. Precaution a. Do not put the battery into re or smash the battery. The capacity of the lithium battery shrinks substantially at low temperature. Therefore, do not use it in an environment below 0. b. Keep the product properly and keep the lens away from scratches and dirt. Use a professional brush and lens blower to clean the product. Protect the product against dirt and damp during storage. c. In case of waterproof case is not mounted, please dont use the camera in harsh environments such as underwater, rain, dust and severe cold etc. CAUTION RISK OF EXPLOSION IF BATTERIES IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCIONS. Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle val-
uable raw materials and the treatment of toxic substances. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera-
tion of the device.Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brou llage est susceptible d'en compromettre le fonctionnement. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certication for use when properly worn on the body. During testing, this product are set to their highest transmission levels and placed in positions that simulate uses against the body with 5mm separation. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certication for use when properly worn on the body. Cet quipement est conforme aux limites dexposition aux rayonnements ISED tablies pour un environnement non contrl. Lutilisateur nal doit suivre les instructions spciques pour satisfaire les normes. Cet metteur ne doit pas tre co-implant ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conu pour rpondre aux exigences dexposition aux ondes radio tablie par le dveloppement nergtique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus leve signale en vertu de cette norme lors de la certication de produit utiliser lorsquil est correctement port sur le corps. The highest SAR value for this YDXJ01FM camera when properly worn on the body is 0.144 W/kg, for ICNIRP recommendation. SAR is measured against head and with the device at a separation of 5 mm to the body, while transmitting at the highest certied output power level in all frequency bands of the mobile device. Principal: Xiaomi Communications Co., Ltd. Manufacturer: Beijing FIMI Technology Co., Ltd. For further information, please go to http://www.mi.com/en/
AddressNo.348, Floor 3, 1# Complex Building, Yongtaijiayuan, Qinghe, Haidian District, Beijing, China 105g 102*72mm0.5mm)
&11C