all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 2.04 MiB | March 04 2020 | |||
1 |
|
Internal Photos | Internal Photos | 1.48 MiB | March 04 2020 | |||
1 |
|
External Photos | External Photos | 456.78 KiB | March 04 2020 | |||
1 |
|
ID Label and Location Info | ID Label/Location Info | 681.31 KiB | March 04 2020 | |||
1 |
|
Agent Letter | Cover Letter(s) | 62.89 KiB | March 04 2020 | |||
1 | Block Diagram | Block Diagram | March 04 2020 | confidential | ||||
1 | Cover Letter(s) | 74.71 KiB | March 04 2020 | |||||
1 | OP | Operational Description | March 04 2020 | confidential | ||||
1 |
|
RF Exposure Info | RF Exposure Info | 155.70 KiB | March 04 2020 | |||
1 | Schematics AP | Schematics | March 04 2020 | confidential | ||||
1 | Schematics Main | Schematics | March 04 2020 | confidential | ||||
1 |
|
Test Report | Test Report | 3.47 MiB | March 04 2020 | |||
1 |
|
Test Setup Photo | Test Setup Photos | 2.77 MiB | March 04 2020 |
1 | User Manual | Users Manual | 2.04 MiB | March 04 2020 |
105g 172*130mm 40P PANTONE Cool Gray 11 C PANTONE 185 C 0.5mm 1mm Tanos VFCC 4.03.0173 V4.0 2020.01.14 1:1 mm Roborock S6 MaxV Robot Vacuum Cleaner User Manual Before using the product, read this manual thoroughly and save it for future reference. V2.0 Tanos V 12.16.docx V3.0 V4.0 Roborock S6 MaxV Robot Vacuum Cleaner User Manual Before using the product, read this manual thoroughly and save it for future reference. Safety Information FCC IC Statement Battery and Charging Product Overview Installation Instructions for Use Routine maintenance Basic Parameters Troubleshooting FAQs 1 6 8 9 15 21 25 32 33 35 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUC-
TIONS BEFORE USING (THIS APPLIANCE), Failure to follow the warnings and instructions may result in electric shock, re Safety Information and/or serious injury. WARNING To reduce the risk of re, electric shock, or injury:
Do not use outdoors or on wet surfaces. Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants. Use only as described in this manual. Use only manufacturers recommended attachments. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do not handle charger, including charger plug, and charger terminals with wet hands. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air ow. Keep hair, loose clothing, ngers, and all parts of body away from openings and moving parts. Do not use to pick up ammable or combustible liquids, such as gasoline, or use in areas where they may be present. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. Do not use without dust bag. Prevent unintentional starting. Ensure the switch is in the o-position before connecting to battery pack, picking up or carry-
ing the appliance. Carrying the appliance with your nger on the switch or energizing appliance that have the switch on invites accidents. 1 Safety Information For use only with roborock CDZRR or CDZRR charger. Recharge only with the charger specied by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of re when used with another battery pack. Use appliances only with specically designated battery packs. Use of any other battery packs may create a risk of injury and re. Turn o the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a re. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Do not use a battery pack or appliance that is damaged or modied. Damaged or modied batteries may exhibit unpredic table behavior resulting in re, explosion or risk of injury. Do not expose a battery pack or appliance to re or excessive temperature. Exposure to re or temperature above C may cause explosion. Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specied in the instructions. Charging improperly or at temperatures outside of the specied range may damage the battery and increase the risk of re. Have servicing performed by a qualied repair person using only identical replacement parts.This will ensure that the safety of the product is maintained. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care. Place the cords from other appliances out of the area to be cleaned. Do not operate the vacuum in a room where an infant or child is sleeping. Do not operate the vacuum in an area where there are lit candles or fragile objects on theoor to be cleaned. Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into. Do not allow children to sit on the vacuum. Do not use the vacuum cleaner on a wet surface. Risk Of Injury. Brush May Start Unexpectedly.Disconnect the main Brush Before Cleaning or Servicing. Do not use the product when the temperature is higher than or lower than , or there is any liquid or sticky substance on the oor. 2 Safety Information SAVE THESE INSTRUCTIONS Household use only. IMPORTANTES MESURES DE S CURIT Lutilisation dun appareil lectrique demande certaines prcautions:
LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CETAPPAREIL), Le non-respect des mises en garde et des instructions peut causer des chocs lectriques, des incendies et/ou des blessures graves. AVERTISSEMENT Pour rduire les risques dincendie, de choc lectrique ou de blessure:
Ne pas exposer la pluie, Ranger lintrieur. Ne pas permettre aux enfants de jouer avec lappareil. Une attention particulire est ncessaire lorsque lappareil est utilize par des enfants ou proximit de ces derniers. Nutiliser que conformment cette notice avec les accessories recommands par le fabricant. Ne pas utiliser si le cordon ou la che est endommag. Retourner lappareil un atelier de reparation sil ne fonctionne pas bien, sil est tomb ou sil a t endommag, oubli lextrieur ou immerg. Ne pas tirer soulever ni trainer lappareil par le cordon. Ne pas utiliser le cordon comme une poigne, le coincer dans lembra-
sure dune porte ou lappuyer contre des artes vives ou des coins. Ne pas faire rouler lappareil sur le cordon. Garder le cordon lcart des surfaces chaudes. Ne pas dbrancher en tyrant sur le cordon. Tirer plutt la che.Ne pas manipuler le chargeur, y compris la prise du chargeur, et les bornes du chargeur avec les mains mouilles. Ninsrer aucun objet dans les ouvertures. Ne pas utiliser lappareil lorsquune ouverture est bloque. Sassurer que de la poussire, de la peluche, des cheveux ou dautres matires ne rduisent pas le debit dair. Maintenir les cheveux, les vtements amples, les doigts et toutes les parties du corps lcart des ouvertures et des pieces mobiles. 3 Safety Information o peuvent se trouver de tells liquides. chaudes. User de prudence lors du nettoyage des escaliers. Ne pas aspirer des liquids inammables ou combustibles, comme de lessence, et ne pas faire fonctionner dans des en-droits Ne pas aspirer de matires en combustion ou qui dgagent de la fume, comme des cigarettes, des allumettesou des cen-dres Ne pas utiliser lappareil si le sac poussire ou le lter nest pas en place. Emcher une mise en marche accidentelle. Sassurer que linterrupteur est la position arrt avant de raccorder la batterie, de lever ou de dplacer lappareil. Transporter lappareil en gardant un doigt sur linterrupteur, ou mettre sous tension un appareil dont linterrupteur est la position marche peut causer un accident. Pour emploi seulement avec roborock CDZRR or CDZRR chargeur.Recharger uniquement avec le chargeur prescrit par le fabricant. Un chargeur convenant un type de batterie peut prsenter un risque dincendie lorsquil est utilis avec une autre batterie. Retirer la batterie de lappareil avant deectuer des rglages, changer les accessoires ou ranger lappareil. Ces mesures de scurit ont pour but dviter une mise en marche accidentelle de lappareil. Lorsque lappareil nest pas utilis, tenir la batterie loin dobjets mtalliques comme des trombones, des pices de mon-naie, des cls, des clous, des vis ou autres petits objets qui pourraient tablir une liaison entre les bornes. Un courtcircuit des bornes des batteries peut causer des brlures ou un incendie. Utiliser uniquement les batteries recommandes pour lappareil. Lutilisation dautres types de batteries peut prsenter un risque de blessure ou dincendie. Lorsque lappareil nest pas utilis, tenir la batterie loin dobjets mtalliques comme des trombones, des pices de monnaie, des cls, des clous, des vis ou autres petits objets qui pourraient tablir une liaison entre les bornes. Un courtcircuit des bornes des batteries peut causer des brlures ou un incendie. Encondition dusage abusif, du liquide peut schapper de la batterie ; viter tout contact avec ce liquide. En cas de contact accidentel, rincer abondamment avec de leau. En cas de contact avec les yeux, consulter galement un mdecin. Le liquide projet peut causer des irritations ou des brlures. Ne pas utiliser une batterie ou un appareil endommag ou qui a t modi. Des batteries endommages ou modies peuvent avoir un comportement imprvisible pouvant causer un incendie, une explosion ou un risque de blessure. Ne pas exposer une batterie ou un appareil la amme ou des tempratures excessives. Lexposition une amme ou des tempratures suprieures C peut causer une explosion. 4 Safety Information de faire garantira la scurit du produit. dentretien. Respecter toutes les instructions de chargement et ne pas charger la batterie ou lappareil des tempratures qui ne sont pas incluses dans la gamme de tempratures indiques dans la notice dinstructions. Un chargement mal ectu. Coner les rparations une personne qualie qui utilisera uniquement des pices de remplacement identiques. Cette faon Ne pas modier ni tenter de rparer lappareil ou la batterie sauf comme il est indiqu dans les instructions dutilisation et loigner les cordons dautres appareils de la zone nettoyer. Ne pas utiliser laspirateur dans une pice o un nourrisson ou un enfant dort. Ne pas utiliser laspirateur dans un endroit o il ya des bougies allumes ou des objets fragiles sur le plancher nettoyer. Ne pas utiliser laspirateur dans une pice o il ya des bougies allumes sur les meubles que laspirateur peut heurter ou se cogner accidentellement. Ne pas laisser les enfants sassoir sur laspirateur. Ne pas utiliser laspirateur sur une surface mouille. Risque de blessures. La brosse motorise peut se mettre en marche dune manire imprvue. Dconnecter la brosse principale avant le nettoyage ou le service. CONSERVER CES INSTRUCTIONS Usage Domestique seulement. Laser Safety described in Laser Notice , dated May , . Class laser product,Complies with FDA CFR . and . except for conformance with IEC - Ed. , as 5 FCC IC Statement Product Name Produce Model Compliance Statement Compliance Information Robotic Vacuum Cleaner with Dock Charger Robotic Vacuum Cleaner Model: roborock S MaxV Dock Charger Model: CDZRR or CDZRR This device complies with part of the FCC Rules. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
() This device may not cause harmful interference, and () this device must accept any interference received, including interference that may cause undesired operation. Company Address Email Correspondence of the responsible party in USA Roborock Technology Co. West th Street, Wilmington, Delaware . support@roborock.com Any changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Warning authority to operate the equipment. L'exploitation est autorise aux deux conditions suivantes :
() l'appareil ne doit pas produire de brouillage, et promettre le fonctionnement. 6
() l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en com-
FCC IC Statement operate the equipment. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. MPE Requirements To satisfy FCC / IC RF exposure requirements, a separation distance of cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Lantenne installe doit tre situe de facon ce que la population ne puissey tre expose une distance de moin de cm. Installer lantenne de facon ce que le personnel ne puisse approcher cm ou moins de la position centrale de lantenne. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins cm des personnes pendant son functionnement. CAN ICES- (B)/NMB-(B) 7 Battery and Charging Please keep the dock charger away from heat (such as heating plates). The battery must be removed from the appliance before it is scrapped. The appliance must be disconnected from the supply mains when removing the battery. The battery is to be disposed of safely.Please do not discard waste batteries. Leave them to a professional recycling organiza-
tion. Do not wipe or clean the chargers shrapnel with a piece of wet cloth or wet hands. Please make sure the cleaner is powered o in shipment and original packaging is advised. If left unused for a long period, please store the cleaner in a cool and dry place after having it fully charged and switched o, charge it at least every three months to avoid the battery being over discharged. Please do not use the product when the temperature is higher than C or lower than C , or there is any liquid or sticky substance on the oor. Battery pack charging temperature
@Max Charging Current:.C Battery pack using temperature
@Max Discharge Current:.C Battery pack storage temperature Storage(month) Long Storage(months) Long Storage(year) If the battery pack store at C over the months period, it should be recharged. C ~ C C ~ C
-C ~ C
@Less than % RH
-C ~ C
@Less than % RH
-C ~ C
@Less than % RH 8 Product Overview Robot Spot Clean Press to start spot cleaning Clean/Power Press to start cleaning Press and hold to turn the robot on or off Power indicator White: Battery level 20%. Red: Battery level < 20%
Flashing slowly: Charging or starting up Flashing red: Error Dock Press to return to Dock Note:
Press any button to stop the robot during cleaning, returning to the Dock, or spot cleaning Reset WiFi Press and hold both Spot Clean and Dock for 3 seconds Cover Grip 9 Product Overview Dustbin Robot WiFi indicator Off: WiFi disabled Flashing slowly: Waiting for connection Flashing quickly:
Connecting Steady: WiFi connected System Reset Water Tank Latch Air Vent Speaker Dustbin lid Dustbin latch Filter 10 Product Overview Accessories Charging Dock Moisture-proof Mat Power Cable Mop Cloth Bracket Mop Cloth 11 Product Overview Robot and Sensors Dock Locator ReactiveAI Cameras Infrared Fill Light Bumper LiDAR Sensor Vertical Bumper Wall Sensor Cliff Sensor Omni-
Directional Wheel Charging Contact Side Brush Main Wheel Main Brush Main Brush Cover Latch Water Tank 12 Product Overview Mopping Module Mop Cloth Slot Mop Cloth Bracket Mop Cloth Bracket Latch Water Tank Stopper Water Filter Water Tank Water Tank Latch Mop Cloth Attachment Zone 13 Charging Dock Power Indicator Product Overview Charging Dock Dock Location Beacon Charging Contacts 14 Installation Important Information 1. Tidy cables and loose items from the ground and move any unstable, fragile, precious, or dangerous items to prevent personal injury or property damage due to items becoming tangled in, struck by, or knocked over by the robot. 2. If using this robot in a raised area, always use a secure physical barrier to prevent accidental falls that may result in personal injury or property damage. Note:
Note: When using the robot for the first time, follow it throughout its whole cleaning route and watch for major obstacles. The robot will be able to clean by itself in future uses. 15 Installation Using the Robot 1. Place the charging dock Keep the Charging Dock on a level surface, flat against a wall. Connect the power cable to the Charging Dock and place any exposed cable into the cable slot. To ensure a better user experience of the mobile app, place the Charging Dock in an area with good WiFi coverage. Note:
Use of the double-sided tape to secure the charging dock is optional. When necessary, remove the double-sided adhesive tape slowly to reduce residue glue. 2. Secure the charging dock with the adhesive tape. Wipe the floor of the area where the charging dock will be placed with a dry cloth, then stick the enclosed double-sided tape to the floor. Place the dock onto the double-sided tape to secure it in place. Note:
Allow at least 0.5m (1.6ft) of clearance on each side, and more than 1.5m (4.9ft) in front of the Charging Dock. If the power cable hangs vertical to the ground, it may be caught by the robot, causing the Charging Dock to be disconnected. The Charging Dock indicator is on when the Charging Dock is electrified, and off when the robot is charging. Do not place the Charging Dock in places that are directly exposed to sunlight, and do not block the Location Beacon. Otherwise the robot may not be able to automatically return to the Charging Dock. Use double-sided tape to stick the Charging Dock down. Double-sided tape
> 0.5m
> 1.5m
> 0.5m 16 Installation 3. Attach the Moisture-Proof Mat After fixing the Charging Dock in place, use a dry cloth to clean the area where the Moisture-Proof Mat will be located. Peel off the outer layer of the double-sided tape attached to the bottom of the Moisture-Proof Mat, and stick the mat to the ground as shown. Note:
Always place the Moisture-Proof Mat on wooden floors. Peel the double-sided tape slowly to minimize residual adhesive. The Moisture-Proof mat attaches better to smooth surfaces. 4. Powering On and Charging Press and hold the button to power on the robot. Wait until the power light is steady, and then place the robot on the Charging Dock to charge. The robot is equipped with a built-in high performance lithium-
ion rechargeable battery pack. To maintain battery performance, keep the robot charged during normal use. Note:
The robot may not be turned on when the battery is low. In this case, connect the robot to the Charging Dock. The color of the power indicator indicates the battery level. White: 20%;
Red: < 20%
17 Installation Connect to the app 5. Download the mobile phone app for more smart features.
(Optional) Reset WiFi The robot supports the Roborock or Mi Home app. Choose the one that best meets your needs. Download the app a. Search for "Roborock" in the App Store or Google Play or scan the QR code to download and install the app. a. b. Open the upper cover and find the WiFi indicator. Press and hold the and buttons until you hear the
"Resetting WiFi" voice alert. Reset is complete when the WiFi indicator flashes slowly. The robot will then wait for a connection. Note:
If the mobile phone fails to connect to the robot, reset the robot WiFi and add it again when it is waiting for a connection. b. Search for "Mi Home" in the App Store or Google Play or scan the QR code to download and install the app. WiFi indicator Off: WiFi disabled Flashing slowly: Waiting for connection Flashing quickly:
Connecting Steady: WiFi connected Add device On the homepage of the app, tap "+" in the top right corner and add the device according to the in-app guide. After a device has been added, it can be found from the list on the home screen. Note:
The actual process may vary due to ongoing app updates. Follow instructions provided in-app. Only 2.4GHz WiFi is supported. 18 Installation Using the Robot 6. Mopping the floor Note:
To prevent excessive dirt buildup on the mop, floors should be vacuumed at least three times before the first mopping session. Remove the water tank Press the water tank latch and slide the tank backwards. Reinstall the water tank Slide the water tank into the robot until you hear it lock with a click. Install the mop cloth Dampen the mop cloth and wring it until it stops dripping. Insert it into the bottom along the slot of the water tank and stick it firmly in place. Note:
Use virtual barriers and no-mop zones to prevent the robot mopping carpeted floors. Fill the water tank Open the water tank, fill it with water, and close it tightly. Note:
To prevent corrosion or damage, do not use cleaning fluid or disinfectant in the water tank. Do not use hot water as this may cause the tank to deform. 19 Installation Using the Robot Install the Mop Cloth Bracket Slide the bracket along the back of the water tank. A click indicates that it is locked in place. Note:
The mop cloth should be cleaned after 60 minutes of mopping to ensure water flow and cleaning quality. 9. Remove the Mop Cloth Bracket When the robot returns to the Charging Dock after cleaning, press the latches on both sides, and slide the Mop Cloth Bracket backwards to remove it. Note:
After mopping, remove the Mop Cloth Bracket, pour out residual water from the water tank, and clean the mop cloth to avoid mold and odor. Remove the Mop Cloth Bracket when not mopping. 7. Adjust the water flow Use the mobile app to adjust water flow as required. 10. Remove the Mop Cloth Bracket from the water tank Press the two side latches inwards and slide the Mop Cloth Bracket backwards as shown to remove it from the water tank. Low Medium High WaterLevel Water Level Water Level 8. Start cleaning. Charging is complete when the power indicator light changes from breathing to a steady white light. Press the button or use the app to start cleaning. 20 Instructions for use On/Off Press and hold the button to power on the robot. The power indicator will turn on and the robot will enter standby mode. When the robot is idle, press and hold the button to turn off the robot and complete the cleaning cycle. Note:
The robot cannot be turned off when it is being charged. Start Cleaning Press the button to start cleaning. The robot will plan its cleaning route according to its scan of the room. It splits a room into zones, first draws out zone edges, then fills the zone in a zigzag pattern. In so doing, the robot cleans all zones one by one, efficiently cleaning the house. Zone 1 has been cleaned. Zone 1 has been cleaned. Pause Note:
Sleep Note:
Cleaning cannot start if the battery level is too low. Allow the robot to charge before restarting cleanup. Before cleaning, tidy cables (including the power cable of the Charging Dock) from the floor. Loose cables may be dragged by the robot, resulting in the disconnection of electrical appliances or damage of cables and property. If cleaning is completed in less than 10 minutes, the area will be cleaned twice. If the battery runs low during the cleaning cycle, the robot automatically returns to the Charging Dock. After charging, the robot will resume where it left off. When the robot is running, press any button to pause it. Then press the button to continue cleaning or the button to return it to the Charging Dock and stop the cleaning cycle. Placing a paused robot on the Charging Dock manually will end the current cleanup. If the robot is paused for over 10 minutes, it will go to sleep, and the power indicator will flash every few seconds. Press any button to wake the robot up. Note:
The robot will not go to sleep when it is on the Charging Dock. The robot will automatically shut down if left in sleep mode for more than 12 hours. Zone 4 is pending. Zone 3 is being cleaned. 21 Spot Cleaning When the robot is in standby or pause mode, press the button to start spot cleaning. In this mode, the robot cleans an 1.5m x 1.5m square area centered on the robot. After spot cleaning, the robot will automatically return to the starting point and stop cleaning. Note:
Starting spot cleaning in Pause mode will stop the current cleaning cycle. If the robot cannot find the Charging Dock, it will return to the most recent starting location. Place the robot on the Charging Dock manually to recharge. 1.5 m Instructions for use Charging Auto: After cleaning, the robot will automatically return to the Charging Dock to recharge. Manual: In Pause mode, press the button to send the robot back to the Charging Dock. The power indicator will breathe as the robot charges. Note:
Error Note:
If an error occurs while the robot is cleaning, the power indicator flashes red and a voice alert will sound. See Troubleshooting for solutions. The robot will go to sleep automatically if left in an Error state for over 10 minutes. Placing the robot on the Charging Dock in an error state will stop the current cleanup. Reset WiFi If the mobile phone fails to connect to the robot because the router configuration has changed, the password has been forgotten, or for any other reason, open the upper cover and find the WiFi indicator. Press and hold the and buttons until you hear the "Resetting WiFi" voice alert. Reset is completed when the WiFi indicator starts to flash slowly, showing that the robot is waiting for a connection. Note:
If the robot waits more than 1 hour for a connection, WiFi will be automatically disabled. If you need to reconnect, reset the WiFi before proceeding. m 5 1
. 22 Instructions for use Selective Room Cleaning Select one or multiple rooms for cleaning in the app. Note:
A full map must have been created, and Map Saving mode switched on before this function can be used. The robot may enter unselected areas during cleaning. Clear obstacles from the ground around the selected rooms as the robot may enter unselected areas. C A Scheduled Cleaning Use the app to set start times for scheduled cleanings. The robot will return to the Charging Dock after each cleaning cycle. Zone Cleaning Draw specific zones in the app for targeted cleaning as required. Note:
The robot may enter unselected areas during cleaning. Clear obstacles from the ground around the selected zones as the robot may enter unselected areas. D Pin n Go Place a target on the map in the app and the robot will navigate to the desired spot. B Cleaning Mode Select Quiet, Balanced, Turbo, or MAX mode in the app. Balanced mode is selected by default. DND Mode During the DND period, the robot stops cleaning and playing voice prompts, and the power indicator dims. DND mode is enabled in factory settings. The default DND period is from 22:00 to 08:00. You can use the app to disable the DND mode or modify the DND period. 23 Instructions for use No-go Zones/Virtual Barriers/
No-Mop Zone Use the app to set no-go zones/virtual barriers/No-Mop Zone. The robot will not enter no-go zones and areas sealed off by virtual barriers while cleaning. No-mop zones only activate when the Mop Cloth Bracket is installed. Note:
"Map saving mode" must be turned on in the app to use virtual no-go zones and barriers. This function can be used only to set cleaning zones. Do not use it to prevent the robot from entering hazardous areas. Moving the robot or changing the home environment may cause the map to become inaccurate and erase virtual barrier and no-go zone settings. Virtual Barriers No-go Zones No-Mop Zone Refilling the water tank or cleaning the mop cloth To add water or clean the mop cloth, press any button to stop the robot and remove the mopping module. After adding water or cleaning the mop cloth, reinstall the mopping module and press the button to continue. More app functions Change cleaning Part replacement Real-time map updates mode View cleaning history Carpet Boost schedule Robot location Map management View robot status DND mode Change robot voice Volume adjustment Firmware update Note:
Functions and details of the Mi Home app may vary slightly due to the continuous app development and upgrades. 24 Routine maintenance Main brush Clean weekly 1. Turn over the robot, press the latch, and remove the main brush cover. 2. Pull out the main brush. Remove and clean the main brush bearing. Use the tool blade to cut away entangled hair on the brush and to clean the bristles. 3. Rotate the main brush cap in the indicated unlock direction to remove the Note:
4. Use the main brush cleaning tool to remove any entangled hair on the brush If there is a large amount of hair, or if hair is tightly entangled, remove it carefully to avoid damage. Using the main brush cleaning tool cap. or bearing. Note:
5. Rotate the main brush cover and main brush bearing in the indicated lock direction to reinstall them. 6. Reinstall the main brush, press on the main brush cover, and lock it. Replace the main brush every 6 to 12 months for optimal cleaning performance. Lock Unlock Alignment Main Brush Bearing Main Brush Cover Latch Main Brush Main Brush Cap 25 Routine maintenance Dustbin and filter Clean weekly 1. Open the top cover, squeeze the Dustbin latches and take out the Dustbin. 2. Open the Dustbin lid as indicated by the arrow and pour out the dirt. 26 Routine maintenance Washable filter Clean every two weeks 1. Open the Dustbin lid as indicated by the arrow and pour out the contents. 3. Remove the filter and clean it with water. Note:
Do not touch the filter with hands, brushes, or sharp objects to avoid damage. 2. Fill the Dustbin with clean water and close the cover. Gently shake the Dustbin, then pour out the dirty water. Note:
To prevent blockage, only use fresh water without cleaning liquid. 4. Rinse repeatedly and tap the filter frame to remove as much dirt as possible. 5. Leave the filter to dry before reinstalling it. Dry the filter thoroughly before use. (Dry for at least 24 hours) Use an alternate filter if necessary. Note:
27 Routine maintenance Battery Water tank Clean as required The robot is equipped with a built-in high-performance lithium-ion battery pack. To maintain battery performance, keep the robot charged during normal use. 1. Open the water tank. 2. Rinse the water inlet filter. 3. Fill the tank with water, shake it, then pour out the water. Note:
If the robot will not be used for an extended period, turn it off and charge it at least every three months to avoid battery damage caused by overdischarge. Charging Dock Clean monthly Use a soft dry cloth to clean the Charging Contacts of the Charging Dock. Mop cloth Clean after use 1. Remove the mop cloth from the Mop Cloth Bracket. Side brush Clean monthly 1. Turn over the robot and unscrew the Side Brush screw. 2. Remove and clean the Side Brush. 3. Reinstall the brush and tighten the screw. Note:
Replace the side brush every 3 to 6 months for optimal cleaning performance. 2. Clean the mop cloth and air-dry it. Note:
A dirty mop cloth will affect mopping performance. Clean the mop cloth before use. Replace the mop cloth every 3 to 6 months for optimal cleaning performance. 28 Routine maintenance Omni-Directional Wheel Clean as required 1. Turn over the robot. 2. Use a tool, such as small screwdriver to pry out the axle and take out the wheel. 3. Rinse the axle and the wheel with water to remove any hair and dirt. 4. Air-dry, reinstall, and press the wheel and axle back in place. Note:
Note:
The Omni-Directional Wheel bracket cannot be removed. Wheel Axle Bracket Reset the System If the robot does not respond when a button is pressed or cannot be turned off, reset the system. Press the Reset button, and the robot will reset automatically. After resetting the system, scheduled cleanup, WiFi, and others will be restored to factory settings. Restore Factory Settings If the robot does not function properly after a system reset, switch it on, then press and hold both the and Reset buttons until you hear the
"Start restoring initial version" voice alert. The robot will then be restored to factory settings. Firmware Upgrade Use the mobile phone app to upgrade the robot firmware. Connect the robot to the Charging Dock and ensure that the battery level is above 20%
before upgrading. The power indicator will flash white quickly during a firmware update. 29 Routine maintenance Robot sensors Clean monthly Use a soft dry cloth to wipe and clean all sensors, including:
1. ReactiveAI Cameras 2. Six cliff sensors at the bottom of the robot 3. Wall sensor on the right side of the robot 4. Charging contacts at the bottom of the robot ReactiveAI Cameras Wall Sensor Cliff Sensor Charging Contacts 30 Routine maintenance Holiday Energy Saving Function When the robot is docked, press and hold "Recharge" for 10 seconds or until you hear an alert sound. This will activate Holiday mode. In this mode the robot will switch to Low Power mode to minimize power consumption. This includes a dimming of the LED indicator, and the stopping of all non-charging related functions including cleaning, remote control over WiFi, and more. To deactivate Holiday mode, press and hold "Recharge" for 10 seconds until the LED indicator brightens. 31 Basic parameters Robot Charging Dock Appearance and Dimensions 35335096.5mm Appearance and Dimensions 15113098mm Parameters Name Parameters 14.4V/5200mAh lithium battery Rated Power Rated Input Rated Output Rated Frequency 28W 100-240VAC 20VDC 1.2A 50-60Hz Name Battery Weight Rated Voltage Rated Power Charging Time Note:
Wireless Connection WiFi Smart Connect Approx. 3.6kg 14.4VDC 66W
<6h The serial number is on a sticker on the underside of the robot. 32 Troubleshooting If an error occurs while the robot is cleaning, the power indicator will flash red and a voice alert will sound. Refer to the following table for troubleshooting. Error Solution Error 1: Rotate the laser head to check that it turns freely. The LDS unit is jammed. Remove any items blocking it then move the robot to a new location and restart. Error 2: Clean and lightly tap the bumper. The bumper is stuck. Tap the bumper repeatedly to dislodge any jammed items. If nothing falls out, move the robot to a new location and restart. Error 3: Move the robot to a new location and restart. A wheel is suspended. Move the robot to a new location and restart. Error 4: Wipe the cliff sensors, move the robot away from raised edges, and restart. The robot is suspended. Move it to a new location and restart. If the problem persists, clean the cliff sensors. This error may also be caused by a dirty cliff sensor. Try wiping all sensors clean. Error 5: Remove the main brush and clean the brush and bearing. The main brush may be tangled up. Remove and clean it. Error 6: Remove and clean the side brush. The side brush may be tangled up. Remove and clean it. Error 7: Look for anything stuck in the main wheels then move the robot to a new location and restart. The main wheels may be jammed. Remove and clean them. Error 8: Clear away any obstacles around the robot. The robot may be stuck. Clear any obstacles around it. Error 9: Install the dustbin and filter. Reinstall the dustbin and filter and check that they are installed properly. If the problem persists, try replacing the filter. Error 10: The filter is either wet or blocked. The filter is not completely dry. Dry the filter for at least 24 hours. The filter may also require cleaning. If the problem persists, replace the filter. 33 Troubleshooting If an error occurs while the robot is cleaning, the power indicator will flash red and a voice alert will sound. Refer to the following table for troubleshooting. Error Solution Error 11: High-intensity magnetic field detected. Move the robot away from the magnetic tape and restart. The robot is too close to a magnetic tape and cannot start. Move it to a new location and restart. Error 12: The battery is too low. Recharge before use. Low battery. Recharge before use. Error 13: Charging error. Clean the charging contact area. Use a dry cloth to clean the charging contacts on the robot and on the charging dock. Error 14: Battery error. Error 15: Clean wall sensor. The battery temperature is either too high or too low. Wait until it returns to normal. The wall sensor is blocked by dust. Wipe clean the sensor. Error 16: Robot is tilted. Place it on flat ground and restart. The robot is tilted. Move it to flat ground and restart. Error 17: Side brush module error. Reset the system. The side brush module is experiencing a fault. Reset the system. Error 18: Vacuum fan error. Reset the system. The vacuum fan is experiencing a fault. Reset the system. Error 21: Vertical bumper pressed. Release it and retry. The vertical bumper has been pressed. Relocate the robot and retry. Error 22: Dock locator dirty. Clean and retry. The dock locator signal is blocked by dust. Clean it and retry. Error 23: Dock location beacon lost. Clean and retry. The dock location beacn is blocked by dirt. Clean it and retry. Error 24: No-go zone or barrier tape detected. Move the robot away and retry. Move the robot away from the virtual no-go zone or barrier tape and retry. Internal Error. Malfunction due to an internal error. Reset the system. Note: A system reset may not resolve all problems. If the problem persists after using the recommendations in the table above, please email our after-sales service team:
US/Non-Europe Support: support@roborock.com Europe Support: support@roborock-eu.com 34 FAQs Problem Solution Unable to power on The battery level is low. Put the robot on the Charging Dock and charge it before use. The battery temperature is too low or too high. Only use the robot within the range of 4-40C (39-104F). Unable to charge Slow charging speed If the Charging Dock is not receiving power, check that both ends of the power cable are properly connected. If contact is poor, clean the contact areas of the Charging Dock and the robot. Confirm that the Charging Dock indicator is on. The robot is charged in an environment at a high or low temperature. To maintain the battery life cycle, the robot automatically reduces the charging speed. The charging contacts may be dirty. Clean them with a dry cloth. Unable to return to dock There are too many obstacles near the Charging Dock. Move it to an open area. The robot is too far from the Charging Dock. Place it closer and retry. Abnormal behavior Restart the robot. Noise during cleaning The main brush, side brush, or main wheels may jammed. Turn off the robot and clean them. If the Omni-Directional Wheel is jammed, use a screwdriver to remove it for cleaning. Poor cleaning performance and/or leaking dust The Dustbin is full and needs emptying. The Filter is blocked and needs cleaning. The main brush is dirty. Clean it and retry. Unable to connect to WiFi WiFi is disabled. Reset the WiFi and try again. WiFi signal is poor. Move the robot to an area with good WiFi reception. Abnormal WiFi connection. Reset the WiFi, download the latest mobile app and retry. The current device is not supported. You can find supported models in the app. Unable to connect to WiFi. There may be an error with your router settings. Contact Roborock customer service for help with troubleshooting. 35 FAQs Problem Solution Scheduled cleaning is not working The battery level is too low. Scheduled cleaning can only begin when the battery level is above 20%. Is power always being drawn when the robot is on the Charging Dock?
The robot will draw power while it is docked to maintain battery performance, but power consumption is extremely low. Does the robot need to be charged for at least 16 hours the first three times it is used?
No. The robot can be used any time after it has been fully charged once. No or little water during mopping Cleaning does not resume after recharging Check whether there is water in the water tank and use the mobile app to set the water flow or check the manual for full instructions on how to correctly install the mop cloth and Mop Cloth Bracket. Make sure that the robot is not in DND mode. DND mode will prevent cleanup. When cleaning a space requiring a top-up charge, if the robot was placed manually on the Charging Dock before it is recharged automatically, it will not be able to continue cleanup. The robot cannot return to the Charging Dock after spot cleaning or when it has been moved manually. After spot cleaning or a significant position change, the robot will re-generate the map. If the Charging Dock is too far away, it may not be able to return for recharging and must be placed on the Charging Dock manually. The robot has begun to miss certain spots The wall sensor or cliff sensors may be dirty. Clean them with a soft dry cloth. The water tank is too full The filter may be blocked and need cleaning. Unable to recognize and avoid objects The ReactiveAI Cameras lens may be dirty or obscured. Use a soft cloth to wipe it and keep the lens clean and free from obstructions. Current AI algorithms cannot recognize dirt but it will keep learning daily. 36 Robot Vacuum Cleaner Manufacturer: Beijing Roborock Technology Co., Ltd. Product Model: roborock S MaxV Address of Manufacturer: Floor , Suite , , , Building C, Kangjian Baosheng Plaza, No. Heiquan Road, Haidian District, Bejing, P.R.CHINA For more product information, visit our website: www.roborock.com For after-sales support, email our after-sales service team:
US/Non-Europe Support: support@roborock.com Europe Support: support@roborock-eu.com
1 | ID Label and Location Info | ID Label/Location Info | 681.31 KiB | March 04 2020 |
Class 1 laser product coborock Product Name: Robotic Vacuum Cleaner Rated Voltage: 14. 4VDC 1040. 10 and 1040. 11 except Product Model: roborock S6 MaxV Rated Power: 66W for conformance with IEC 60825-1 Ed. 3., as described Product ID: XXXXXX in Laser Notice 56, dated May For Household Use Only Pour usage domestique seulement For use only with roborock CDZ11RR or CDZ12RR Charger. Conforms to UL Std. 1017 Cert. to @) Pour emploi seulement avec roborock CDZ11RR ou CSA Std. 22.2 No. 243 CDZ12RR chargeur. hi Sal 1A ON FCC ID: 2AN20-S6MAXV IC: 23317-S6MAXV XXXXXKAXAKKAK, WARNING To Reduce The Risk Of Electric Shock-Do not use out-
doors or on wet surfaces. To reduce the risk of injury, user must read instruction manual. AVERTISSEMENT Pour rduire le risque de choc lectrique - Ne pas uti-
liser A Vextrieur et ne pas aspirer des dchets hu-
mides. Pour dduire le risque de blessure, l'utilisateur doit lire la notice dinstruction CAUTION Risk Of Injury. Brush May Start Unexpectedly. Remove the main Brush Before Cleaning or Servicing. ATTENTION Risque de blessures. La brosse motorise peut se mettre en marche d'une manire imprvue. Retirer la brosse principale avant le nettoyage ou le service. FCC Statement: See User Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inter ference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3 (B)
1 | Agent Letter | Cover Letter(s) | 62.89 KiB | March 04 2020 |
Beijing Roborock Technology Co.,Ltd. Date: December 28, 2019 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:
The Beijing Roborock Technology Co.,Ltd. the undersigned, hereby authorizes Mr. Hongfei Wu of TV Rheinland Shanghai Co., Ltd, to act on the behalf of the Beijing Roborock Technology Co.,Ltd. solely in matters relating to the application for an FCC equipment authorization for FCC ID: 2AN2O-S6MAXV including the signing of documents in connection with this Application. Necessary acts carried out by Beijing Roborock Technology Co.,Ltd. on our behalf of the Beijing Roborock Technology Co.,Ltd. in connection with the Application shall have the same effect as acts of the Beijing Roborock Technology Co.,Ltd. The Beijing Roborock Technology Co.,Ltd. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Thank you for your attention to this matter. Yours Sincerely,
(Qianqian Hu) Name TitleCertification Engineer CompanyBeijing Roborock Technology Co.,Ltd.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2020-03-04 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2020-03-04
|
||||
1 | Applicant's complete, legal business name |
Beijing Roborock Technology Co., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0026926923
|
||||
1 | Physical Address |
Floor 6,Suite 6016,6017,6018,Building C, Baosheng Plaza,No.8 Heiquan Road,Haidian District
|
||||
1 |
Floor 6,Suite 6016,6017,6018,Building C, Baosheng
|
|||||
1 |
BEIJING, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
F******@TUV.COM
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
2AN2O
|
||||
1 | Equipment Product Code |
S6MAXV
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Q****** H********
|
||||
1 | Title |
Sr. Certification Manager
|
||||
1 | Telephone Number |
+86-1********
|
||||
1 | Fax Number |
+8610********
|
||||
1 |
h******@roborock.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
TUV Rheinland (Shanghai) Co., Ltd
|
||||
1 | Name |
H****** W******
|
||||
1 | Physical Address |
No. 177, Lane 777, West Guangzhong Road
|
||||
1 |
Shanghai
|
|||||
1 |
China
|
|||||
1 |
H******@tuv.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Robotic Vacuum Cleaner | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. The device Supports 20 MHz and 40MHz bandwidth. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
MRT Technology (Suzhou) Co., Ltd.
|
||||
1 | Name |
M******** C****
|
||||
1 | Telephone Number |
+86-5******** Extension:
|
||||
1 |
m******@mrt-cert.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.1960000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC