SIM7100E User Manual SIM7100E User Manual Rev 1 Beijing Xinlian Chuangzhan Electronic Technology Co., LTD Tel:+86010-62153842/62153840 http://www.silion.com.cn Page 1 of 11 SIM7100E User Manual Directory 1. A revision history ..................................................................................................................... 3 2. Product introduction ................................................................................................................. 4 3. Product features ....................................................................................................................... 4 4. Electrical characteristics .......................................................................................................... 5 5. Pin configuration and function Description ................................................................................6 6. Application Information ............................................................................................................ 7 7. Physical Properties ................................................................................................................... 8 Page 2 of 11 SIM7100E User Manual 1. A revision history file The number The version number V1.0 Artificial person /
The modifier Proposed/revis Change the ed date reason Change the content 2021-10-16 The initial release No Page 3 of 11 SIM7100E User Manual 2. Product introduction The UHF high-power module SIM7100E is a high-performance UHF RFID read-write module developed by the technology team of Xinliangzhan based on the new generation of IMPINJ RF chip E710. It is specially designed to meet the requirements of high-performance RFID handheld devices, mobile or portable RFID devices. The SIM7100E module provides one MMCX antenna interface, supporting up to 30 dBm RF output. This module has the characteristics of low power consumption, small size and high sensitivity. Combined with the advanced multi tag algorithm of Xinliangzhan, it is a priority for RFID mobile devices. 3. Product features New generation E710 RF chip Impinj new generation E710 UHF RF reader chip is adopted, which has high sensitivity, wide reading range, low power consumption and strong performance. Super tag reading performance The tag reading speed is fast, the reading is stable, the multi tag anti-collision ability is strong, and the reading distance is long. When using the 4dBi four wall spiral antenna, the reading distance is more than 9 meters, and the multi tag reading speed is fast, up to 900 pieces/second. Lower power consumption It can work normally in the 3.6V low voltage mode. The maximum power output power consumption is 6.5W, and the standby power consumption is only 0.25W. The excellent low power consumption design makes the product have a longer service life. Multiple monitoring functions and excellent stability The module supports label RSSI detection, antenna connection status detection, and working temperature detection. Multiple data detection is more convenient for users to use efficiently; The module can work stably in the ambient temperature of -20 to+65, and supports stable operation in the ambient humidity of 5% - 95%. It has high efficiency and stable performance and can be applied to a variety of harsh working environments. Page 4 of 11 SIM7100E User Manual 4. Electrical characteristics parameter conditions min type max unit Frequency Frequency range According Customization 840 Frequency step value According Customization 250/500 output output power Output power accuracy Flatness of output power Channel isolation label Reception sensitivity Profile1 Inventory label peak 5
+/- 1
+/- 0.2 32
-82 900 960 30 MHz KHz dBm dB dB dB dBm tag/s speed Label cache Logic level VILInput Low Voltage VIHInput High Voltage Temperature range Storage temperature Working temperature The input power The power supply voltage Can make model Standby mode Read the card model 96 bit EPC 1000 1200 tag
-0.5 2
-40
-20 3.6 0.8 Vdd+0.5 85 65 5.25 V V V mA mA mA 5.0 40 50 1300 Pout=30dBm, 50 Load The current will vary depending on the load antenna. Page 5 of 11 SIM7100E User Manual Absolute maximum rated parameter parameter power supply voltage Digital I/O Voltage to GND Working temperature Storage temperature rating
+5V 3.3V
-20 ~ +65
-40 ~ +85 5. Pin configuration and function description 5.1 Definition of FPC connector The serial number 1 2 3 4 5 define VCC(+3.6 - 5V) VCC(+3.6 - 5V) GND GND EN module power enableLOW(POWER DOWN) HIGH&DISCONNECT(ACTIVE) Page 6 of 11 SIM7100E User Manual 6 7 8 9 10 11 12 Digital Output 2 GPIO OUT2 Digital Input 1 GPIO IN1 Digital Input 2 GPIO IN2 RXD (DATA INPUTTTL level) TXD (DATA OUTPUTTTL level) RST (LOW ACTIVEPlease hang in the air if not used) Digital Output 1 GPIO OUT1 5.2 Definition of bottom welding point The serial number 1 2 3 4 5 6 7 8 9 define GND GND VCC(+3.6 - 5V) VCC(+3.6 - 5V) EN module power enableLOW(POWER DOWN) HIGH&DISCONNECT(ACTIVE) RXD (DATA INPUTTTL level) TXD (DATA OUTPUTTTL level) RST (LOW ACTIVEPlease hang in the air if not used) Digital Output 1 GPIO OUT1 6. The application of information The input power It is recommended to filter the VCC port with a capacitance of 100~470uF to reduce the traction t o the power supply caused by the quick opening and closing of the power amplifier during RF tran smission. 0.1uF/100pF capacitors filter out power supply ripple in different frequency bands. Since the current is high when the module is working at full power, the module may not work sta bly when the battery is low when the handheld device is powered directly by the battery, so it is r ecommended to boost the VCC to 5V. Page 7 of 11 SIM7100E User Manual Enable or reset EN is enabled, with built-in pull-up resistance (100k) to VCC. When the module is powered on at h igh level or suspended, the module will be powered off when it is connected to low level (low leve l should be less than 0.4V, high level should be greater than 0.9V and less than VCC). Rst reset, built-in pull-up resistance to 3.3V, reset when connected to low level. GPIO interface Input:
Logic low 0.8V minimum 0V Logic high 2 V Maximum 3.3 V Output:
Logic Low maximum 0.4V Logic High has a minimum of 2.9V and a maximum of 3.3V The maximum output current of the I/o port is 5mA. The antenna connection The output impedance of the antenna port is 50 ohms, and the antenna standing wave ratio is rec ommended to be less than 1.5. A better antenna standing wave ratio can get better card reading effect. Communication interface (rxd/txd) The communication interfaces RXD and TXD are at TTL level, and the default baud rate is 115200b ps 7. Physical properties Product size55.9mm*35.6mm*6.0mm weight21g Page 8 of 11 SIM7100E User Manual 8 Peripheral Design Requirement 8.1 List of applicable FCC rules FCC Part15 Subpart C, Section 15.247 FCC regulatory information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. End Device Labelling Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID: 2AQ9M-SIM7100E any similar wording that expresses the same meaning may be used. RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 8.2 Additional testing Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e.FCC transmitter rules ) listed on the grantand that the host product Page 9 of 11 SIM7100E User Manual manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification .If the grantee markets their product as being Part 15 Subpart B compliant( when it also contains unintentional - radiator digital circuit y) then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed . 2.2 List of applicable FCC rulesFCC Part15 Subpart C, Section 15.247. 2.3 Usage: The sample module is used in customized products, such as handheld computers and all-in-one computers. 2.4 Because the module has shielding cover,it is a unrestricted module. 2.5 The antenna is not on the sample and needs to be added externally. Customers can connect the external antenna from the antenna pin of the module to the antenna adapter of the housing according to their own needs. 2.6 RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.7Antenna Type:External Antenna Antenna Gain(Peak): 3.04dbi 2.8 The final end product must be labeled in a visible area with the following: 2AQ9M-SIM7100E 2.9 Operation Frequency: 902.75~927.25MHz Number of Channel: 50 Channels Modulation: ASK Host manufacturer must perfom test of radiated & conducted emission and spurious emission,etc according to the actual test modes for a stand-alone modular transmitter in a host.Only when all the test results of test modes comply with FCC requirements, then the end product can be sold legally. 2.10Additional testing Part15SubpartB disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized forthe specific rule parts (i.e. FCC transmitter rules )listedonthegrant and that the host productmanufacturer is responsible for compliance to any other FCC rules that apply to the host notcovered by the modular asbeing Part transmitter 15SubpartBcompliant( when it also contains unintentional - radiator digital circuit y) then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed . Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. the user is encouraged to try to correct grantee markets certification product grant their the of
.If Page 10 of 11 SIM7100E User Manual Connect the equipment into an outlet on a circuit different Consult the dealer or an experienced radio/TV technician for help.
connected.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. to which the receiver is from that FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Page 11 of 11