640 Safety Instructions Product Introduction The Smartmi 2-in-1 Purier and Humidier humidies using evaporation, so it wont produce a visible mist. 160 Handling Installation Power Cable While in Use Usage Restrictions Please turn o and disconnect the machine before moving it. Please empty the water tank before moving the machine. Please install the machine according to the instructions provided to avoid electrical shock, re, bodily harm, or other dangers. Do not connect the power cable until you have nished seing up the machine. To avoid risk of re, shock, or damage:
Plug the power cable into an appropriate socket. Do not pull or stretch the power cable. Disconnect the power cable before performing maintenance, or moving the machine. If the power cable is damaged, send it to the manufacturer or a repair facility to be replaced by professionals. If the product starts producing a strange sound, odor, or gets very hot, cease use immediately. Do not put your nger or other foreign objects inside the protective covering, intake port, exhaust port, or other movable parts. Do not allow hair or loose threads to get caught in the intake or exhaust ports. Do not sit or lean on the machine. Ensure adequate ventilation when used alongside household gas appliances (such as gas stoves or water heaters) to avoid carbon monoxide poisoning. If the alarm stops working, it may be caused by water accumulation in the upper casing. It will not aect use. It should resume working normally aer the water has evaporated. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Do not use under the following circumstances to avoid shock, re, or other dangers:
If the purier is tilted, it may misread the water level in the tank, or cause spills. Please ensure that the device is even before use. Control Panel Exhaust / Water Relling Port Upper Casing Evaporating Basin Evaporating Basin Knob Water Tank Temperature and Humidity Sensor Intake Port Water Level Detector Water Level Limit Power Cable Lower Casing Product Introduction Control Panel Instructions Water Level Indicator Mode Indicator Wi-Fi / Light Buon Wi-Fi Indicator Light Power / Mode Buon Automatic Mode: Automatically adjusts humidier based on current temperature and humidity inside the room. Speed 1: Low Speed 2: Medium Speed 3: High Usage Adding Water Suitable Water: Tap Water, Mineral Water, Puried Water 1 Add water through the relling port 2 Add water into the water tank You can directly add water through the relling port while the purier is powered on. The water will ow down into the tank, and the water level indicator will change to reect how much water has been added. Stop when all the lights are on. Take o the top half of the purier, and directly add water into the tank. Take care not to ll past the maximum water level indicator. Water Level Indicator Light Status Water Level Mode Indicator Light Status Water Level < 10%
10% Water Level < 40%
40% Water Level < 60%
60% Water Level < 80%
80% Water Level < 100%
Water Level 100%
Over Max Water Level On O On Blinking O Current Mode Automatic Mode Speed 1: Low Speed 2: Medium Speed 3: High Note: If you ll past the maximum water level, the water level indicator lights will ash and the machine will give o warning beeps, and water should be stopped adding immediately. 4 Smartmi Evaporative Humidier Read this manual carefully before use, and retain it for future reference 1 2 3 Usage Usage Specications Turning the Machine On and O, and Changing Modes Adjusting Brightness Reseing the Wi-Fi Cleaning the Evaporating Basin Press the Power / Mode Buon to turn the machine on. The rst time you start the machine, it will default to automatic mode. You can press the buon again to switch modes. Holding the buon for 2 seconds will turn the machine o. Press the Wi-Fi / Light Buon to adjust brightness between high, low, and o. If your phone is unable to connect to the purier, press and hold both the Wi-Fi / Light buon and the Power / Mode buon for 5 seconds. Once you hear a beep, the Wi-Fi has been successfully reset. You can remove the evaporating basin and use a so cloth to wipe down, or clean water to rinse o the basin. You can also twist o the knob on the evaporating basin to clean the individual discs that comprise the basin. Note: The machine will not turn on if the water level in the tank is lower than the minimum water level. You will have to add water to turn the machine on. Air Dry mode Note: You can turn the Air Dry mode on or o through the Mijia app. If Air Dry mode is on:
When the water level drops lower than 10%, the humidier will continue to operate for about 8 hours to dry out the water tank, avoiding strange odors caused by stagnant water. If Air Dry mode is o:
When the water level drops lower than 10%, the humidier will automatically turn o. Quick Set-up This product is compatible with the Mijia Smart Platform. It can be controlled through the Mijia app, supports the MIUI system, and can connect with other Mijia smart products. 1 2 Search for Mijia through your app store, or scan the QR code below to install the Mijia app. Enable your phones Bluetooth, and go to the front page of the Mijia app. Press the + in the upper right corner, select Add a Device, and select Smartmi 2-in-1 Purier and Humidier. Aer adding the device, you should see it on the front page of the Mijia app. 5 Repair and Installation Turn the humidier o and disconnect the power cable before cleaning the device Cleaning the Water Tank You can rinse the water tank with clean water, or wipe it down with a so cloth to ensure the cleanliness of your humidier, and prevent strange odors produced by stagnant or dirty water. As illustrated below, you can twist o the knob on the basin to remove the individual disks that comprise the basin. TEN S A F L O O S E N Note: If you frequently use the humidier, we recommend cleaning it once a week. 6 Product Name Smartmi Evaporative Humidier Rated Voltage 100-240V Capacity Model Number CJXJSQ02ZM Rated Frequency 50/60Hz Humidication Rate Dimensions 240 240 363 mm Rated Waage 8W Wi-Fi Approx. 4.0L 240mL / h Wi-Fi IEEE 802.11 b/g/n 2.4GHz Gross Weight Approx. 4.3kg Noise Generated 47dB(A) Net Weight Approx. 5.1kg Product Type Evaporative Humidier Network standby power consumption
< 2.0W Regulatory compliance information FCC ID: 2AP98-CJXJSQ02ZM This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device is comply with Class B limits. All peripherals must be shielded and grounded. Operation with non-certied peripherals or non-shielded cables may results in interference to radio or reception. MODIFICATION: Any changes or modications not expressly approved by the grantee of this device could void the users authority to operate the device. FCC RF EXPOSURE STATEMENT:
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Manufacturer: Beijing Smartmi Electronic Technology Co., Ltd. Address: 11-1102, Oce Building Rainbow City, NO.68 Qinghe Mid-Street, Haidian District, Beijing Standard: Q/BJZMK0008-2018 7 YT-V1.0(20180531) 105g 4 0.1mm R V0.9 2018.04.18 PANTONE Cool Gray 11C ID SKU 69 1:1 mm