www.unistrong.com/english Quick Start for Odin Odin Series Quick Start 1. Appearance Antenna Earpiece Touch panel Other function keys Power Microphone Start menu External connector antenna Back strap screws Speaker Camera Lanyard tether point Back cover screw Back cover Back strap holder Front Back Reset button Mini USB socket Bottom 2. Operating steps I. Charging II. Fix TF card/SIM card/battery IIITurn on the collector IV. Connect to PC to install application or data V. Collect GIS data with internal GPS and GIS application VI. Upload data Charging Insert the Li-ion battery into the battery charger to charge. Remark: mini USB cable can also be used to charge the receiver. When normally charged, there is charging icon in the screen if receiver is off and there is charging icon to the top right corner in the screen if receiver is on. 1Turn the back cover screw to the open position according to the instruction on the back cover and take off the back cover(figure 1). 2Fix the SIM card and TF card according to the instruction in the battery cabin(figure 2). 3Fix the battery. 4Fix the back cover and turn the back cover screw to the lock position according to the Fix TF card/SIM card/Battery www.unistrong.com/english Quick Start for Odin instruction on the back cover(figure 1). Figure 1 Figure 2 Turn on/off collector 1Make sure there is enough power in battery, or connect receiver to PC with mini USB cable(with battery in). 2Press power button for 35 seconds to turn on(until the boot screen appears)/ turn off. Remark: if receiver is down, press the reset button in the bottom of receiver to reset. Connect to PC 1Make sure Microsoft ActiveSync application has been installed in PC. 2Connect receiver to PC with mini USB cable. 3ActiveSync application connect receiver and PC automatically. There is icon Install Application appears in the tool bar of PC and Synchronization Setup Wizard appears meantime, click Cancel. 4Click Browse to check the files in receiver, then transfer data between PC and receiver. 1Make sure Odin is connect with PC via ActiveSync. 2Click install file on PC to start the installation. If the install file is compatible for mobile device, copy the file into Odin and click to start the installation. 3Select installation directory in OdinFlash Storage is suggested, click install. Remark: its suggested to install the application in Flash Storage, save data in TF card. Use GPS Option 1 Use the internal GPS settings. www.unistrong.com/english Quick Start for Odin 1. Start->Settings->System->GPS Settings->Satellite State 2. Click Please click here to startup A-GPS. 3. Wait until get GPS information. Option 2 Use user-define application software: Set COM port as COM6 and baud rate as 57600 in application. Here take u-center mobile application software for example. 1. Install u-center mobile and run it. 2. Set Port and Baud rate in Rx menu. www.unistrong.com/english Quick Start for Odin 3. Wait until get GPS information. Use Camera Select Start->Picture & Videoselect Camera or camera icon to take photos. Click screen and select OK to exit. Wireless ConnectionBluetooth/GPRS/WIFI Bluetooth icon 1Select Start->Settings->Connections->Wireless management, click the on the right of Bluetooth to activating the Bluetooth device. 2Select Start-> Settings-> Bluetooth, click Add new device, system will search available Bluetooth device. Select the device in refurbished list and click Next in the bottom right corner, input password. 3Select Next, input password in external Bluetooth device and finish the connection. Remark: The password is used to the connection between Bluetooth devices and can be setup freely, such as 1234. www.unistrong.com/english Quick Start for Odin GPRS 1Make sure there's SIM card in receiver. 2Select Start->Settings->Connections->Connections. 3Click Add a new modem connection. 4Input connection name, select Cellular Line(GPRS), click Next. 5Input cmnet, click Next. 6Click Finish and add new connection successfully. 7Click Manage existing connections. 8Click on the new connection for a while and select Connect. 9There is GPRS identifier on the signal icon on the top right corner, indicates the successful connection. WIFI 1 Select 'Start->Settings->Connections->Wi-Fi'
2 Click Search for Networks, select a network that listed. Follow the installation guide to input password and finish the connection. 3. Useful Settings Screen response Select Start-> Settings-> System-> Screen, click Align Screen icon and follow the guide to align the screen. Adjust backlight Select Start-> Settings-> System-> Backlight', adjust backlight status according to the guild. Auto power off Select Start-> Settings-> System-> Power-> Advanced, set the power off time in different conditions. Remove programs Select Start-> Settings-> System-> Remove Programs, select the program in the list and click OK to remove. Fall alarm Select Start-> Settings-> System-> Motion Sensor, select Fall Alarm, check or not the function of sharp warning sound when Odin is dropped. You can also open or close the Screen rotation function in this menu. Restore Factory Defaults Select Start-> Settings-> System-> Restore Factory Defaults, restore factory defaults settings according to the guide. Caution: Restore factory defaults settings, all the data and programs will be lost. www.unistrong.com/english Quick Start for Odin 4. Environmental Operating temperature: -20~+50 Storage temperature: -30~+70 Drop: 1.5m drop onto all faces Casing: Dustproof and resistant to heavy wind driven rain per IP66 standard Humidity: 5% ~ 95% (non-condensing) www.unistrong.com/english Quick Start for Odin Appendix Product Safety Warnings Safety and compliance information Use responsibility Read all instructions and safety information before use to avoid injury. Battery safety Charge battery only in temperature ranging from 32 to 113 (0 to 45). CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to battery manufacturers instructions. WiFi safety Turn WiFi off in areas where WiFi use is prohibited or when it may cause interference or danger, such as in airplanes while flying. Care and maintenance Odin is an electronic product and should be treated with care, to reduce the risk of fire, electronic shock, or product damage. Do not expose this device to rain, moisture, or any type of liquid that corrodes electronic circuits. If your device gets wet, immediate turn the power off. Allow the device to dry completely before using it again. Clean the display with a soft cloth, and be careful not to wipe the display with anything abrasive. Do not expose your device to extreme heat or cold. For example, do not leave it in the trunk of your car in high heat conditions. Do not attempt to open the device other than as instructed in this manual. Rough handling can break internal circuitry. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. Use only the recommended accessories. Do not excessive sound pressure from earphones and headphones, which can cause hearing loss. www.unistrong.com/english Quick Start for Odin USB Data Cables ThisversionsupportstheUSBinterface.YoucanconnectyourOdinwiththe PCviatheUSB&datacable,copyingormovingthefilesamidtheOdinandPC,or browsingtheimages,recordfilesandvideofilessavedintheOdinviathePC. 1InserttheUSBdatacableconnectorintotheUSBinterfaceoftheOdin. 2ConnecttheotherterminaloftheUSBdatacablewiththeUSBinterfaceofthePC. CAUTION THECONNECTIONTOUSBINTERFACESHASTOBELIMITEDTO USB2.0VERSIONORHAIGHER THECONNECTIONTOSOCALLEDPOWERUSEISPROHIBITED For more information, please turn to www.unistrong.com/English Email: overseas@unistrong.com Manual Requirements according 15.19 / RSS-210 NOTICE:
This device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference interference that may cause undesired operation. received, including Manual Requirements according 15.21 NOTICE:
Changes or modifications made to this equipment not expressly approved by Beijing UniStrong Science & Technology Co., Ltd may void the FCC authorization to operate this equipment. Manual Requirements according 15.105 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Manual / Label requirements according ICES-003 NOTICE:
This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe [B] est conforme la norme NMB-003 du Canada. NOTICE:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
[Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.]
SAR Information:
The SAR limit adopted by USA (FCC) is 1.6 Watts/kilogram (W/kg) averaged over one gram of tissue. Device types (FCC ID: YYEMG75875075X) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for the body is 1.221 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0 cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0 cm separation distance between the users body and the back of handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.