Configuration and installation guide Copyright All rights reserved. Patent pending. Before you start Dear reader, We recommend that you read and follow this step-by-step guide to configuration and installation of the BEKEY door unit. The guide includes:
1. Product specification 2. Configuration of the door unit 3. Installation on the door*
In order to ensure correct functionality of the product it is very important that the above steps are followed as described in this document. Best regards, BEKEY
*This installation guide pertains to the lock type Regular deadbolt. If you have purchased an add-on package with your BEKEY door unit, by step 3, follow the instructions from the package to complete the installation on your lock. Should you have any questions, please contact BEKEY support through our website www.bekey.dk/support. 1. Product specification 4 x 1.5V AA Batteries Battery cover Switch for clockwise/counter-
clockwise opening Attachment plate Thumb turn Enables manual opening. Lock button Press to unlock/lock. LED BLUE = Lock is active RED = Batteries need replacement Switch for latch/bolt lock
. Three hex screw holes Fastens the door unit to the installation plate. 2. Configuration of the door unit In order to configure your door unit, you need to choose the correct settings for the unit. Position the unit as shown below. If your door has a latch lock, you simpkly close the door in order to lock it without the need for a key. If your door has a bolt lock, you need a key in order to lock the door. Position the top switch according to your lock type:
Latch lock = switch up Bolt lock = switch down Next you need to set the lock direction, i.e. does the key turn clockwise or counter-clockwise when unlocking. Look at your door from the outside and determine if the key turns clockwise or counter-clockwise. If the key is turned counter-clockwise when unlocking, you need to set the bottom switch to Left. If the key is turned clockwise when unlocking, you need to set the bottom switch to Right. Counter-clockwise = Left (switch up) Clockwise = Right (switch down) Remember that the direction is determined by observing the door from the outside!
3. Installation on the door Remember in case you have purchased an add-on package with your BEKEY door unit, you must follow the installation guide enclosed in the package. Enclosed in the package is a tool set. Your lock type may require certain screw bits that are not enclosed in the package. Should this be the case, we recommend that you take a picture of the bits and contact your local tool store. Placement of the door unit Check that the size of the door unit does not affect the functionality of the door or the existing lock. The door unit can be installed in three different ways, as shown below, depending on the position of the door handle:
Installation overview 1) If the lock is a bolt lock, place the bolt in the unlocked position, A. Place the thumb turn, B, vertically. 2) Make sure that the key is not sitting in the outside keyhole, C. 3) Place the installation screws, D, in the two holes on the back of the attachment plate, E, and place the spindle, F, through the center of the attachment plate. Adjust the two holes in the cylinder, C, and fasten the attachment plate. 4) Place the door unit over the attachment plate on the door G/E and fasten the three hex screws in the bottom of the door unit, H, (illustration below).
+
The door unit. Attachment plate as it is placed on the door. Step-by-step installation Step 1 Remove the two screws, A and B, from the existing thumb turn. The number of screws depends on the lock type. Most locks have two screws. Step 2 1 Replace the thumb turn with the attachment plate from the package. Place the plate with the flat side against the door. Reuse the two screws, A and B, and fasten the plate on the door. 2 4 A. The plate is fastened to the door, and the spindle sits in the center of the plate. The distance between the door and the tip of the spindle must not exceed 25 mm length. in B. Place the door unit over the attachment plate. Adjust the center to fit the spindle. If the existing spindle is too short, or of a different type than shown here, please use the spindle and plate from the package. 3 Place as shown in picture 4. Step 3 When the door unit is attached to the attachment plate, tighten the three screws at the bottom of the unit. This ensures that the door unit is fastened to the attachment plate. Step 4 Remove the battery cover Insert 4 AA-batteries Step 5 Test the functionality of the door unit by pressing the lock button, D, and then manually turn the thumb button, B, on the unit. Step 6 Test whether the key, E, on the outside of the door works properly, locking and unlocking the door easily. 4. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. No changes shall be made to the equipment without the manufacturers permission as this may void the users authority to operate the equipment. The Bekey as ML1-1 has been designed and complies with the safety requirements for portable (<20cm) RF-
exposure in accordance with FCC rule part 2.1093 and KDB 447498 D01. BEKEY A/S Bredebjergvej 6 DK-2630 Taastrup +45 4343 9990 www.bekey.dk