FCC ID: K7SF5D8636V2 N Wireless Modem Router

N Wireless Modem Router User Manual PM01527ea-C F5D8636-4 English Franais DEutsch nEDErlanDs Espaol italiano Table of CoNTeNTs table of contents sections 1 2 3 4 5 6 7 8 9 10 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 Using the Web-based advanced User Interface . . . . . . . . . . . 38 Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Placement of your N Wireless Modem Router . . . . . . . . . . . . . . . . . . . 3 2 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Knowing your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setup Assistant Software System Requirements . . . . . . . . . . . . . . . . 9 4 Connecting and Configuring your Modem Router . . . . . . . . . . 13 Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Viewing the DHCP Client List Page . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Configuring the Wireless Network Settings . . . . . . . . . . . . . . . . . . . . 41 Setting WPA Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Setting WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Setting MAC Address Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Configuring the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Using Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Restarting the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 7 Manually Configuring Network settings . . . . . . . . . . . . . . . . . . 74 8 Recommended Web browser settings . . . . . . . . . . . . . . . . . . . 79 5 alternate setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 10 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 N Wireless Modem Router i INTRodUCTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 Thank you for purchasing the Belkin N Wireless Modem Router (the Router) . Following are two short sectionsthe first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance . Please be sure to read through this User Manual completely, and pay special attention to the section entitled Placement of your N Wireless Modem Router on page 3 . benefits of a Home Network Share one high-speed Internet connection with all the computers in your home Share resources, such as files and hard drives among all the connected computers in your home Share a single printer with the entire family advantages of a Wireless Network Here are some of the advantages of setting up a Belkin Wireless Network:

Mobility youll no longer need a dedicated computer room now you can work on a networked laptop or desktop computer anywhere within your wireless range Easy installation Belkins Setup Assistant application makes setup simple Share documents, music, video, and digital pictures Store, retrieve, and copy files from one computer to another Simultaneously play games online, check Internet email, and chat Easy Expansion the wide range of Belkin networking products let you expand your network to include devices such as printers and gaming consoles No cabling required you can spare the expense and hassle of retrofitting Ethernet cabling throughout the home or office Flexibility set up and access printers, computers, and other networking devices from anywhere in your home Widespread industry acceptance choose from a wide range of interoperable networking products . N Wireless Modem Router 1 INTRodUCTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 Revolutionary N Wireless Technology with MIMo (N MIMo) Think of conventional radio transmission as a two-lane highway . The speed limit governs the maximum allowable flow of traffic through that lane . Compared with conventional radios, one-dimensional smart antenna systems help move traffic through that lane faster and more reliablyanalogous to a four-lane road on which traffic consistently moves at a rate closer to the speed limit . Belkins N MIMO helps traffic move at the speed limit and opens more lanesto become the superhighway in this example . The rate of traffic flow is multiplied by the number of lanes that are opened . Your Belkin N Wireless Modem Router uses a new smart-antenna technology called Multiple Input Multiple Output (MIMO) . N MIMO complies with the IEEE draft 802 .11n specification . It increases speed, range, reliability, and spectral efficiency for wireless networking systems . The element that makes Belkins N MIMO technology different from a conventional radio is the use of multiple antennas and two simultaneous data streams to deliver wireless transfers around your home or office . A conventional radio uses one antenna to transmit a data stream . Belkins N MIMO, on the other hand, uses two antennas . This design helps combat distortion and interference . Belkins N MIMO is multidimensional . It builds on one-dimensional smart-antenna technology by simultaneously transmitting two data streams through the same channel, which increases wireless capacity . Another element that enhances Belkins N MIMO is the use of aggregation as specified in the draft 802 .11n specification . By shortening the space between packets and combining multiple smaller packets into one larger packet, Belkins N MIMO can transmit more data through available bandwidth . N Wireless Modem Router 2 INTRodUCTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 Placement of your N Wireless Modem Router Important factors for Placement and setup Your wireless connection will be stronger the closer your computer is to your Router . Typical indoor operating range for wireless devices is between 100 and 200 feet . In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases . This may or may not be noticeable to you . As you move further from your Router, connection speed may decrease . Factors that can weaken signals simply by getting in the way of your networks radio waves are metal appliances or obstructions, and walls . If you have concerns about your networks performance that might be related to range or obstruction factors, try moving the computer to a position between five and 10 feet from the Router in order to see if distance is the problem . If difficulties persist even at close range, please contact Belkin Technical Support . Note: While some of the items listed below can affect network performance, they will not prohibit your wireless network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this checklist may help . 1 . Router Placement Place your Router, the central connection point of your network, as close as possible to the center of your wireless network devices . To achieve the best wireless network coverage for your wireless clients

(i .e ., computers enabled by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless USB Adapters):

N Wireless Modem Router 3 Ensure that your Routers networking antennas are parallel to each other, and are positioned vertically (toward the ceiling) . If your Router itself is positioned vertically, point the antennas as much as possible in an upward direction . In multistory homes, place the Router on a floor that is as close to the center of the home as possible . This may mean placing the Router on an upper floor . Try not to place the Router near a cordless 2 .4GHz phone . 2 . avoid obstacles and Interference Avoid placing your Router near devices that may emit radio noise, such as microwave ovens . Dense objects that can inhibit wireless communication include:

Refrigerators Washers and/or dryers Metal cabinets Large aquariums Metallic-based UV tinted windows INTRodUCTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 If your wireless signal seems weak in some spots, make sure that objects such as these are not blocking the signals path (between your computers and Router) . 3 . Cordless Phones If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone:

Try moving cordless phones away from your Router and your wireless-enabled computers . Unplug and remove the battery from any cordless phone that operates on the 2 .4GHz band (check manufacturers information) . If this fixes the problem, your phone may be interfering . If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless network . For example, change the phone to channel 1 and move your Router to channel 11 . See your phones user manual for detailed instructions . If necessary, consider switching to a 900MHz or 5GHz cordless phone . 4 . Choose the Quietest Channel for your Wireless Network In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours . Use the Site Survey capabilities found in the Wireless Utility of your wireless adapter to locate any other wireless networks that are available

(see your wireless adapters user manual), and move your Router and computers to a channel as far away from other networks as possible . Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices . For Belkin wireless networking products, use the detailed Site Survey and wireless channel information included with your wireless network card . See your network cards user guide for more information . These guidelines should allow you to cover the maximum possible area with your Router . Should you need to cover an even wider area, we suggest the Belkin Wireless Universal Range Extender/Access Point . N Wireless Modem Router 4 INTRodUCTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 5 . secure Connections, VPNs, and aol Secure connections typically require a user name and password, and are used where security is important . Secure connections include:

Virtual Private Network (VPN) connections, often used to connect remotely to an office network The Bring Your Own Access program from America Online (AOL), which lets you use AOL through broadband provided by another cable or DSL service Most online banking websites Many commercial websites that require a user name and password to access your account Secure connections can be interrupted by a computers power management setting, which causes it to go to sleep . The simplest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website . A second alternative is to change your computers power management settings so it does not go to sleep; however, this may not be appropriate for portable computers . To change your power management setting under Windows, see the Power Options item in the Control Panel . If you continue to have difficulty with Secure Connections, VPNs, and AOL, please review the steps above to be sure you have addressed these issues . N Wireless Modem Router 5 PRodUCT oVeRVIeW table of contents sections 1 2 3 4 5 6 7 8 9 10 Product features In minutes you will be able to share your Internet connection and network your computers . The following is a list of features that make your new Belkin N Wireless Modem Router an ideal solution for your home or small office network . Works with both PCs and Mac Computers The Router supports a variety of networking environments including Mac OS 8 .x, 9 .x, X v10 .x, Linux, Windows 98, Me, NT, 2000, XP, and Vista . All that is needed is an Internet browser and a network adapter that supports TCP/IP (the standard language of the Internet) . Network status display Lighted LEDs on the front of the Router indicate which functions are in operation . Youll know at-a-glance whether your Router is connected to the Internet . This feature eliminates the need for advanced software and status-monitoring procedures . Web-based advanced User Interface You can set up the Routers advanced functions easily through your web browser, without having to install additional software onto the computer . There are no disks to install or keep track of and, best of all, you can make changes and perform setup functions from any computer on the network quickly and easily . NaT IP address sharing Your Router employs Network Address Translation (NAT) to share the single IP address assigned to you by your Internet Service Provider while saving the cost of adding additional IP addresses to your Internet service account . N Wireless Modem Router 6 sPI firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding . Integrated 10/100 4-Port switch The Router has a built-in, four-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more . The switch features automatic detection so it will adjust to the speed of connected devices . The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources . Universal Plug and Play (UPnP) UPnP is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant . support for VPN Pass-Through If you connect to your office network from home using a VPN connection, your Router will allow your VPN-equipped computer to pass through the Router and to your office network . PRodUCT oVeRVIeW table of contents sections 1 2 3 4 5 6 7 8 9 10 built-In dynamic Host Configuration Protocol (dHCP) MaC address filtering For added security, you can set up a list of MAC addresses (unique client identifiers) that are allowed access to your network . Every computer has its own MAC address . Simply enter these MAC addresses into a list using the Web-Based Advanced User Interface and you can control access to your network . Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network . The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup . setup assistant The Setup Assistant, second generation of Belkins renowned Easy Install Wizard, takes the guesswork out of setting up your Router . This automatic software determines your network settings for you and sets up the Router for connection to your Internet Service Provider (ISP) . In a matter of minutes, your Router will be up and running on the Internet . Note: Setup Assistant software is compatible with Windows 2000, XP, and Vista, Mac OS X v10 .4 and v10 .5 . If you are using another operating system, the Router can be set up using the Alternate Setup Method described in this User Manual (see page 27) . Integrated N Wireless access Point N MIMO is an exciting new wireless technology based on the draft IEEE 802 .11n specification . It employs MIMO (Multiple Input Multiple Output) smart-antenna technology that achieves data rates of up to 300Mbps .*

Actual throughput is typically lower than the connected data rate and will vary depending on your networking environment .

*NoTe: The standard transmission rate300Mbpsis the physical data rate . Actual data throughput will be lower . N Wireless Modem Router 7 KNoWINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 Package Contents Belkin N Wireless Modem Router Quick Installation Guide Belkin Setup Assistant Software CD RJ11 Telephone Cord RJ45 Ethernet Networking Cable ADSL (Asymmetric Digital Subscriber Line) Micro filter*

Power Supply User Manual in CD Network Status Display Guide Security Guide

*ADSL Micro filter varies by country . If its not included, you will need to purchase one N Wireless Modem Router 8 KNoWINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 system Requirements Internet Connection settings An active ADSL service with a telephone wall jack for connecting the Router At least one computer with an installed network interface adapter TCP/IP networking protocol installed on each computer No other DHCP server on your local network assigning IP addresses to computers and devices Internet browser setup assistant software system Requirements A computer running Windows 2000, XP, or Vista; or Mac OS X v10 .4 and v10 .5 Minimum 1GHz processor and 512MB RAM Internet browser The Setup Assistant contains a database of Internet Service Providers

(ISP) in each country to help you set up your Router quickly . If your ISP is not on the list, please collect the following information from your ISP before setting up the Router:

Internet connection protocol: _________ (PPPoE, PPPoA, Dynamic IP, Static IP) Multiplexing method or Encapsulation: __________ (LLC or VC MUX) Virtual circuit: VPI (Virtual Path Identifier) __________

(a number between 0 and 255) VCI (Virtual Channel Identifier) __________

(a number between 1 and 65535) For PPPoE and PPPoA users: ADSL account user name _____________ and password _______________ For static IP users: IP Address ___ . ___ . ___ . ___ Subnet Mask ___ . ___ . ___ . ___ Default Gateway Server ___ . ___ . ___ . IP address for Domain Name Server ___ . ___ . ___ . ___

(If given by your ISP) N Wireless Modem Router 9 KNoWINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 1 . security OFF Solid Blue Flashing Blue 2 . Wireless-Computer status OFF Solid Blue Blinking Amber 3 . Wired-Computer status OFF Solid Blue Blinking Amber Wireless security is OFF Wireless security is ON WPS sync is in progress Wireless computer is not present Wireless computer is connected to the Router Problem with wireless computer connecting properly to the Router Wired computer is not present Wired computer is connected to the Router Problem with wired computer connecting to the Router currently The Router has been designed to be placed on a desktop . All of the cables exit from the rear of the Router for better organization and utility . The Network Status Display is easily visible on the FRONT of the Router to provide you with information about network activity and status . See the Network Status Display Guide for more detailed information . 1 . 7 . 2 . 3 . 4 . 5 . 6 . N Wireless Modem Router 10 KNoWINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10

4 . Router/Power status

6 . Internet status When you apply power to the Router or restart it, a short period of time elapses while the Router boots up . During this time, the router icon blinks . When the Router has completely booted up, the router icon becomes a solid light, indicating the Router is ready for use . OFF Blinking Blue Solid Blue 5 . adsl line status Router is off Router is booting up Router is on and ready This icon lights in blue to indicate that your Router is connected properly to the ADSL . It turns amber when problem is detected . OFF Blinking Blue Solid Blue Blinking Amber Router is NOT connected to a functioning ADSL line Router is attempting to connect to the ADSL line Router is connected to an ADSL service and is functioning properly Problem with ADSL line OFF Blinking Blue Solid Blue Blinking Amber Router is NOT connected to the Internet Router is attempting to connect to the Internet Router is connected to the Internet Router is not connected to the Internet This unique icon shows you when the Router is connected to the Internet . When the light is off, the Router is NOT connected to the Internet . When the light is blinking amber, the Router is attempting to connect to the Internet . When the light is solid blue, the Router is connected to the Internet . When using the Disconnect after x minutes feature, this icon becomes extremely useful in monitoring the status of your Routers connection . 7 . WPs Push button This button is for the Wi-Fi Protected Setup feature . Refer to the Changing the Wireless Security Settings section for more details . N Wireless Modem Router 11 KNoWINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 8 . Connection to adsl Gray 10 . Reset button The Reset button is used in rare cases when the Router may function improperly . Resetting the Router will restore the Routers normal operation while maintaining the programmed settings . You can also restore the factory default settings by using the Reset button . Use the restore option in instances where you may have forgotten your custom password . Push and release the Reset button . The lights on the Router will momentarily flash . The Router light will begin to blink . When the Router light becomes solid again, the reset is complete . i . Resetting the Router ii . Restoring the factory defaults Press and hold the Reset button for at least 10 seconds, then release it . The lights on the Router will momentarily flash . The Router light will begin to blink . When the Router light becomes solid again, the restore is complete . 11 . Power Jack Black Connect the included 12V/1A DC power supply to this jack . This port is for connection to your ADSL . Connect your ADSL to this port . An RJ11 telephone cord is provided in the package . 9 . Connections to Wired Computers Yellow Connect your wired (non-wireless) computers to these ports . These ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable . The ports are labeled 1 through 4, with onboard LEDs on the connectors . 11 10 9 8 N Wireless Modem Router 12 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 Verify the contents of your box . you should have the following:

setup assistant Belkin N Wireless Modem Router RJ11 Telephone Cord RJ45 Ethernet Networking Cable Power Supply Belkin Setup Assistant Software CD User Manual on CD Micro Filter (if your ISP line requires) Quick Installation Guide Security Guide Network Status Display Guide Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task . You can use it to get your Router up and running in minutes . The Setup Assistant requires that your Windows 2000 or XP computer be connected directly to your ADSL and that the Internet connection is active and working at the time of installation . If it is not, you must use the Alternate Setup Method section of this User Manual to configure your Router . Additionally, if you are using an operating system other than Windows 2000, XP, or Vista, or Mac OS X v10 .4 and v10 .5, you must set up the Router using the Alternate Setup Method section of this User Manual . N Wireless Modem Router 13 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 step 1: Hardware Connections 3 4 1 2 5 1 .1 brand-New setup Follow these steps if you are not replacing an existing modem . If you are replacing an existing modem, skip to the next section, Replacing an Existing Modem or Modem Router, starting on page 15 . Note: Some ADSL connections require a micro filter . Your ADSL provider can tell you if you need one . Belkin includes a micro filter in regions known to use them . You may or may not have received one in your box . 1 . Unpack your new Router from the box and place it next to your computer . Raise the Routers antennas . 4 . Plug your Routers power supply into the black port labeled Power on the back of your Router . 2 . Retrieve the yellow RJ45 cable that was included with your Router . First, connect one end to any yellow port labeled Wired on the back of your Router . Then, connect the other end to the networking port on the back of your computer . 3 . Retrieve the included gray RJ11 phone cord . Connect one end to the gray port labeled ADSL line on the back of your Router . Then connect the other end to your ADSL connection (either a wall jack or an ADSL splitter) . N Wireless Modem Router 14 5 . Wait 20 seconds for the Router to start up . Look at the display on the front of the Router . Make sure the Wired and Router icons are lit up in blue . If they are not, recheck your connections . CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 3 1 4 2 3 4 5 6 7 8 9 10 1 2 5 1 .2 Replacing an existing Modem or Modem Router Follow these steps if you currently have a modem or a modem router that you will be replacing with your new Router . Important: Please unplug the power adapter of your old modem from your wall outlet first . 1 . Unpack your new Router from the box and place it next to your old modem . Raise the Routers antennas . Unplug your old modems power cord . 2 . Locate the cable that connects your old modem to your computer . Unplug that cable from your old modem, and plug it into any yellow port labeled Wired on the back of your new Router . 3 . Locate the cable that connects your old modem to the ADSL wall jack . Unplug it from your old modem and then connect it to the gray port labeled ADSL line on the back of your Router . 4 . Plug your Routers power supply into the black port labeled Power on the back of your Router . 5 . Wait 20 seconds for the Router to start up . Look at the display on the front of the Router . Make sure the Wired and Router icons are lit in blue . If they are not, recheck your connections . N Wireless Modem Router 15 LANADSL CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 step 2: set Up the Router Run the setup assistant software select Country Select your country from the drop-down box . Click Begin to continue . 1 . Shut down any programs that are running on your computer at this time . Turn off any firewall or Internet-connection-sharing software on your computer . 2 . Insert the CD into your computer . The Setup Assistant will automatically appear on your computers screen within 15 seconds . Click on Setup Assistant to run the Setup Assistant . Follow the instructions there . Note for Windows Users: If the Setup Assistant does not start up automatically, select your CD-ROM drive from My Computer and double-click on the file named SetupAssistant to start the Setup Assistant . IMPoRTaNT: Run the Setup Assistant from the computer that is directly connected to the Router from Step 1 .1B . N Wireless Modem Router 16 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 Confirmation screen Progress screen Verify that you have completed all QIG steps by checking the box to the right of the arrow . Click Next to continue . Setup Assistant will show you a progress screen each time a step in the setup has been completed . N Wireless Modem Router 17 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 2 .1 Checking settings 2 .2 Verifying Hardware Connections The Setup Assistant will now examine your computers network settings and gather information needed to complete the Routers connection to the Internet . The Setup Assistant will now verify your hardware connection . N Wireless Modem Router 18 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 2 .3 Naming your Wireless Network The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID) . This is the name of your wireless network to which your computers or devices with wireless network adapters will connect . You can either use the default or change it to something unique . Write down this name for future reference . If the Router is capable of High Speed Mode, this option will be checked . You can turn off this option later using the Bandwidth Switch described in this User Manual (see page 44) . Click Next to continue . 2 .4 Requesting Internet account Info (if needed) Select your ISP from the drop-down boxes . N Wireless Modem Router 19 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below . Click Next to continue . 2 .5 Configuring the Router The Setup Assistant will now configure your Router by sending data to the Router and restarting it . Wait for the on-screen instructions . Note: Do not disconnect any cable or power off the Router while the Router is rebooting . Doing so will render your Router inoperable . N Wireless Modem Router 20 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 2 .6 Checking Internet Connection Congratulations We are almost done . The Setup Assistant will now check your connection to the Internet . You have finished installing your new Belkin Router . You will see the Congratulations screen when your Router can connect to the Internet . You can begin surfing by opening your browser and going to any website . You can use the Setup Assistant to set up your other wired and wireless computers to connect to the Internet by clicking Next . If you decide to add computers to your Router later, select Finish return to Main Menu and then click Next . N Wireless Modem Router 21 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 Troubleshooting If the Setup Assistant is not able to connect to the Internet, you will see the following screen . Follow the on-screen instructions to go through the troubleshooting steps . 2 .7 optional: assistance Connecting other Computers This optional step will help you to connect additional wired and wireless computers to your network . Follow the on-screen instructions . N Wireless Modem Router 22 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working . You can now surf the Internet . Click Next to return to the main menu . step 3: set Up Wireless security Run the Security Assistant Software Now that your network is set up and working, it is recommended that you turn on wireless security to prevent unauthorized access to your network from neighboring wireless-enabled computers . The Security Assistant will guide you through the process . Click Security Assistant and follow the on-screen instructions . IMPoRTaNT: Run the Setup Assistant from the computer that is directly connected to the Router from Steps 1 .1B and 1 .2B . N Wireless Modem Router 23 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 Progress screen 3 .1 Picking the security Type The Security Assistant will show you a progress screen each time a step has been completed . Select the security type for your wireless network and click Next to continue . N Wireless Modem Router 24 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 3 .2 Creating a Network Key 3 .3 Transferring the Key Enter a network key (PSK) for your wireless network and click Next to continue . After setting up your wireless security, you will have to transfer the network key to each of your wireless computers . Click on Transfer Key if you have a USB flash drive . Follow the on-screen instructions, or click on Print to print the information . Manually enter it to each wireless computer . Then, click Next to continue . N Wireless Modem Router 25 CoNNeCTINg aNd CoNfIgURINg yoUR ModeM RoUTeR table of contents sections 1 2 3 4 5 6 7 8 9 10 3 .4 Verifying the Connection Congratulations If all your wireless computers are able to connect to the Router, click Next . If you are having trouble, select I had problem with at least one computer and click Next . Then, follow on-screen instructions . Once you have verified that your wireless computers are properly connected, your wireless network is set up and secured . You now can run your network wirelessly and securely . Click Finish to take you back to the main menu . N Wireless Modem Router 26 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 step 1: Hardware Connections follow the Quick Installation guide See the QIG or Step 1: Hardware Connections from the previous section . step 2: set your Computers Network settings to Work with a dHCP server See the section in this User Manual called Manually Configuring Network Settings for directions . step 3: Configuring the Router Using the Web-based advanced User Interface Using your Internet browser, you can access the Routers Web-Based Advanced User Interface . In your browser, type 192 .168 .2 .1 (do not type in anything else such as http:// or www) . Then press the Enter key . N Wireless Modem Router 27 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 logging into the Router logging out of the Router You will see the Routers home page in your browser window . The home page is visible to any user who wants to see it . To make any changes to the Routers settings, you have to log in . Clicking the Login button or clicking on any one of the links on the home page will take you to the login screen . The Router ships with no password entered . In the login screen, leave the password blank and click the Submit button to log in . One computer at a time can log into the Router for the purposes of making changes to the settings of the Router . Once a user has logged in to make changes, there are two ways that the computer can be logged out . Clicking the Logout button will log the computer out . The second method is automatic . The login will time out after a specified period of time . The default login time-out is 10 minutes . This can be changed from one to 99 minutes . For more information, see the section in this manual titled Changing the Login Time-Out Setting . N Wireless Modem Router 28 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 Understanding the Web-based advanced User Interface The home page is the first page you will see when you access the Advanced User Interface (UI) . The home page shows you a quick view of the Routers status and settings . All advanced setup pages can be reached from this page .

(13)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(1) N Wireless Modem Router 29 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 1 . Quick-Navigation links 6 . Connect/disconnect buttons You can go directly to any of the Routers advanced UI pages by clicking directly on these links . The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find . Click in the header (Marked in bold) of each tab and it will show you a short description of the tabs function . 2 . Home button The home button is available in every page of the UI . Pressing this button will take you back to the home page . 3 . Help button The Help button gives you access to the Routers help pages . Help is also available on many pages by clicking more info next to certain sections of each page . 4 . login/logout button This button enables you to log in and out of the Router with the press of one button . When you are logged into the Router, this button will change to read Logout . Logging into the Router will take you to a separate login page where you will need to enter a password . When you are logged into the Router, you can make changes to the settings . When you are finished making changes, you can log out of the Router by clicking the Logout button . For more information about logging into the Router, see the section called Logging into the Router . 5 . Internet-status Indicator This indicator is visible in all pages of the Router, indicating the connection status of the Router . When the indicator says Connected in blue, the Router is connected to the Internet . When the Router is not connected to the Internet, the indicator will read Not Connected in RED . The indicator is automatically updated when you make changes to the settings of the Router . N Wireless Modem Router 30 Use these buttons to manually connect or disconnect your ADSL connection as needed . 7 . language Shows the active language for the Advanced User Interface . Select a desirable language by clicking one of the available languages . 8 . Version Info Shows the firmware version, boot version, hardware version, and serial number of the Router . 9 . laN settings Shows you the settings of the Local Area Network (LAN) side of the Router . Changes can be made to the settings by clicking on any one of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the LAN quick-navigation link on the left side of the screen . 10 . Internet settings Shows the settings of the Internet/WAN side of the Router that connects to the Internet . Changes to any of these settings can be made by clicking on the links or by clicking on the Internet/WAN quick-

navigation link on the left side of the screen . 11 . features Shows the status of the Routers firewall, wireless, and UPnP, Remote Management features . Changes can be made to the settings by clicking on any one of the links or by clicking the quick-navigation links on the left side of the screen . alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 Connection Type From the Connection Type page, you can select one of these five connection types based on the instruction provided by your ISP:

PPPoE PPPoA Dynamic/Fixed IP (1483 Bridged) Static IP (IPoA) Modem Only (Disable Internet Sharing) Select the type of connection you use by clicking the radio button (1) next to your connection type and then clicking Next

(1) 12 . adsl Info Shows the ADSL status and transmission rates . 13 . Page Name The page you are on can be identified by this name . This User Manual will sometimes refer to pages by name . For instance LAN > LAN Settings refers to the LAN Settings page . step 4: Configuring your Router for Connection to your Internet service Provider (IsP) The Internet/WAN tab is where you will set up your Router to connect to your Internet Service Provider (ISP) . The Router is capable of connecting to virtually any ISPs system provided you have correctly configured the Routers settings for your ISPs connection type . Your ISP connection settings are provided to you by your ISP . To configure the Router with the settings that your ISP gave you, click Connection Type (a) on the left side of the screen . Select the connection type you use . If your ISP gave you DNS settings, clicking DNS (b) allows you to enter DNS address entries for ISPs that require specific settings . Clicking MAC Address (C) will let you clone your computers MAC address or type in a specific WAN MAC address, if required by your ISP . When you have finished making settings, the Internet Status indicator will read connection OK if your Router is set up properly . a b C N Wireless Modem Router 31 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 setting your IsP Connection Type to PPPoe or PPPoa PPPoE (Point-to-Point Protocol over Ethernet) is the standard method of connecting networked devices . It requires a user name and password to access the network of your ISP for connecting to the Internet . PPPoA (PPP over ATM) is similar to PPPoE, but is mostly implemented in the UK . Select PPPoE or PPPoA and click Next . Then enter the information provided by your ISP, and click Apply Changes to activate your settings . 1 . User Name Enter the user name . (Assigned by your ISP) . 2 . Password Enter your password . (Assigned by your ISP) . 3 . Retype Password Confirm the password . (Assigned by your ISP) . 4 . service Name (optional) A service name is rarely required by an ISP . If you are not sure if your ISP requires a service name, leave this blank . 5 . IP assigned by IsP 1) for the dynamic IP connection Select Yes if your ISP instructed you to use Dynamic IP . 2) for the static IP connection Select No if your ISP instructed you to use Static IP . IP Address Enter an IP address assigned by your ISP for the Router WAN interface . N Wireless Modem Router 32 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 setting your Connection Type to dynamic/fixed IP (1483 bridged) This connection method bridges your network and ISPs network together . The Router can obtain an IP address automatically from your ISPs DHCP server or accept a fixed IP address assigned by your ISP . 6 . VPI/VCI Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here . (Assigned by your ISP) . 7 . encapsulation Select your encapsulation type (supplied by your ISP) tospecify how to handle multiple protocols at the ATM transport layer . VC-MUX: PPPoA Virtual Circuit Multiplexer (null encapsulation) allows only one protocol running per virtual circuit with fewer overheads . llC: PPPoA Logical Link Control allows multiple protocols running over one virtual circuit (more overhead) . 8 . MTU Enter the MUT value for your ISP . 9 . disconnect after of x minutes of no activity Checking the box and enter the number of minute that you want the modem router to auto disconnect after no activity . After this time has been exceeded, the connection will be terminated . Click Apply Changes to save and activate your settings . To go back to the original settings before saving, click Clear Changes . Or click any of the Quick-Navigation links for other options . Your new settings will not be saved unless your click Apply Changes . N Wireless Modem Router 33 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 for dynamic IP connection:

1 . IP assigned by IsP Select Yes if your ISP instructed you to use Dynamic IP . 2 . VPI/VCI Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here . These identifiers are assigned by your ISP . 3 . encapsulation Select LLC or VC MUX your ISP uses . Click Apply Changes to save and activate your settings . To go back to the original settings before saving, click Clear Changes; or click any of the Quick-Navigation links for other options . Your new settings will not be saved unless you click Apply Changes . for static IP connection:

1 . IP assigned by IsP Select No if your ISP instructed you to use fixed IP . 2 . IP address Enter an IP address assigned by your ISP for the Router WAN interface . 3 . subnet Mask Enter a subnet mask assigned by your ISP . 4 . default gateway Enter a default gateway IP address assigned by your ISP . 5 . VPI/VCI Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameters here . These identifiers are assigned by your ISP . 6 . encapsulation Select the LLC or VC MUX your ISP uses . Click Apply Changes to save and activate your settings . To go back to the original settings before saving, click Clear Changes . Or click any of the Quick-Navigation links for other options . Your new settings will not be saved unless your click Apply Changes . N Wireless Modem Router 34 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 setting your IsP Connection Type to static IP (IPoa) This connection type is also called Classical IP over ATM or CLIP, which your ISP provides a fixed IP for your Router to connect to the Internet . 1 . WaN IP address Enter an IP address assigned by your ISP for the Router WAN interface . 2 . subnet Mask Enter a subnet mask assigned by your ISP . 3 . Use static default gateway Enter a default gateway IP address . If the Router cannot find the destination address within its local network, it will forward the packets to the default gateway assigned by your ISP . 4 . VPI/VCI Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here . These identifiers are assigned by your ISP . 5 . encapsulation Select LLC or VC MUX your ISP uses . Click Apply Changes to save and activate your settings . To go back to the original settings before saving, click Clear Changes . Or click any of the Quick-Navigation links for other options . Your new settings will not be saved unless your click Apply Changes . N Wireless Modem Router 35 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10 setting your Connection Type to Modem only (disable Internet sharing) In this mode, the Router simply acts as a bridge passing packets across the DSL port . It requires additional software to be installed on your computers in order to access the Internet . 1 . VPI/VCI Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameters here . (Assigned by your ISP) . 2 . encapsulation Select the LLC or VC MUX your ISP uses . Click Apply Changes to save and activate your settings . To go back to the original settings before saving, click Clear Changes . Or click any of the Quick-Navigation links for other options . Your new settings will not be saved unless your click Apply Changes . N Wireless Modem Router 36 alTeRNaTe seTUP MeTHod table of contents sections 1 2 3 4 5 6 7 8 9 10

(1) setting Custom domain Name server (dNs) settings A Domain Name Server is a server located on the Internet that translates Universal Resource Locaters (URLs) like belkin .com to IP addresses . Many Internet Service Providers (ISPs) do not require you to enter this information into the Router . The Automatic from ISP box (1) should be checked if your ISP did not give you a specific DNS address . If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly . If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address . Leave the Automatic from ISP box checked . To enter the DNS address settings, uncheck the Automatic from ISP box and enter your DNS entries in the spaces provided . Click Apply Changes (2) to save the settings

(2) N Wireless Modem Router 37 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Using your Internet browser, you can access the Routers Web-Based Advanced User Interface . In your browser, type 192 .168 .2 .1 (do not type in anything else such as http:// or www) then press the Enter key . You will see the Routers home page in your browser window . Viewing the laN settings Clicking on the header of the LAN tab (1) will take you to the LAN tabs header page . A quick description of the functions can be found here . To view the settings or make changes to any of the LAN settings, click on LAN Settings (2) or to view the list of connected computers, click on DHCP client list (3) .

(1)

(2)

(3) N Wireless Modem Router 38 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Changing laN settings All settings for the internal LAN setup of the Router can be viewed and changed here .

(1)

(2)

(3)

(4)

(5)

(6) N Wireless Modem Router 39 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 1 . IP address 4 . IP Pool The IP address is the internal IP address of the Router . The default IP address is 192 .168 .2 .1 . To access the advanced setup interface, type this IP address into the address bar of your browser . This address can be changed if needed . To change the IP address, type in the new IP address and click Apply Changes . The IP address you choose should be a non-routable IP . Examples of a non-routable IP are:

192 .168 .x .x (where x is anything between 0 and 255) 10 .x .x .x (where x is anything between 0 and 255) 2 . subnet Mask There is no need to change the subnet mask . It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so . The default setting is 255 .255 .255 .0 . 3 . dHCP server The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically . The default setting is On . The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network . To turn off the DHCP server, select Off and click Apply Changes . The range of IP addresses set aside for dynamic assignment to the computers on your network . The default is 2100 (99 computers) . If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on Apply Changes . The DHCP server can assign 100 IP addresses automatically . This means that you cannot specify an IP address pool larger than 100 computers . For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit . The starting IP address must be lower in number than the ending IP address . 5 . lease Time The length of time the DHCP server will reserve the IP address for each computer . We recommend that you leave the lease time set to Forever . The default setting is Forever, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer . Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time . This also means that a particular computers IP address may change over time . If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address . For this reason, you will not want the IP address to change . 6 . local domain Name (optional) The default setting is Belkin . You can set a local domain name

(network name) for your network . There is no need to change this setting unless you have a specific advanced need to do so . You can name the network anything you want such as MY NETWORK . N Wireless Modem Router 40 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Viewing the dHCP Client list Page Configuring the Wireless Network settings You can view a list of the computers (known as clients), which are connected to your network . You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computers network interface card (NIC) . Pressing the Refresh (4) button will update the list . If there have been any changes, the list will be updated . The Wireless tab lets you make changes to the wireless network settings . From this tab you can make changes to the wireless network name or Service Set Identifier (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point .

(1)

(2)

(3)

(4) N Wireless Modem Router 41 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Network Name (ssId) To identify your wireless network, a name called the SSID is used . The SSID is your network name . The default network name of the Router is Belkin_N_ADSL_ followed by six digits that are unique to your Router . Your network name will look something like Belkin_N_ADSL_123456 . You can change this to anything you choose, or you can leave it unchanged . Keep in mind, if you decide to change your wireless network name, and there are other wireless networks operating in your area, your network name needs to be different from other wireless networks that may be operating in your area . To change the SSID, type in the SSID that you want to use in the SSID field (1) and click Apply Changes

(2) . The change is immediate . If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your new network name . Refer to the documentation of your wireless network adapter for information on making this change .

(1)

(2) Note: Please periodically check for new Router firmware updates from the Utilities > Firmware update page . Newer firmware can fix problems, add wireless features, and/or improve wireless performance

(see page 66) . N Wireless Modem Router 42 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Channel 1) off There are a number of operating channels from which you can choose in the United Kingdom (and most of Europe), Australia, and most of Asia, there are 13 . In other countries, there are other channel requirements . Your Router is configured to operate on the proper channels for the country in which you reside . The channel can be changed if needed . If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks . extension Channel The IEEE 802 .11n draft specification allows the use of a secondary channel to double the bandwidth (see the Using the Bandwidth Switch section on the next page) . An appropriate extension channel will be displayed when operating in 40MHz mode (see the Using the Wireless Mode Switch section below) . The channel can be changed if necessary . Using the Wireless Mode switch This switch allows you to set the Routers wireless modes . There are several modes . Note: Some modes may require firmware updates to be enabled . This mode will turn OFF the Routers access point, so no wireless devices can join the network . Turning off the wireless function of your Router is a great way to secure your network when you are away from home for a long period of time, or dont want to use the wireless feature of the Router at a certain time . 2) 802 .11g Setting the Router to this mode will allow only 802 .11g- and 802 .11b-compliant devices to join the network . N/draft 802 .11n devices will operate at the 802 .11g speed only . 3) 802 .11b & 802 .11g & 802 .11n Setting the Router to this mode will allow N/draft 802 .11n-, 802 .11g-, and 802 .11b-compliant devices to join the network . 4) 802 .11n Setting the Router to this mode will allow only N/draft 802 .11n-compliant devices to join the network, keeping out 802 .11g and 802 .11b devices . N Wireless Modem Router 43 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Using the bandwidth switch Protected Mode switch This switch allows you to set the Routers wireless bandwidth modes . There are several modes available:

1) 20MHz/40MHz Setting the Router to this mode allows it to switch automatically between 20MHz and 40MHz operation . This mode enables 40MHz operation, to maximize speed for N draft 802 .11n-compliant devices when conditions permit . When a legacy 802 .11g access point is presented and occupies an adjacent secondary channel, the Router automatically reverts to 20MHz operation to maximize compatibility . Set the Router to this mode for higher performance . 2) 20MHz Protected mode ensures proper operation of N, draft 802 .11n-compliant devices on your wireless network when 802 .11g or 802 .11b devices are present or when there is heavy 802 .11g or 802 .11b traffic in the operating environment . Use protected mode if your network consists of a mix of Belkin N Wireless Cards and 802 .11g or 802 .11b cards on your network . If you are in an environment that includes little to no 802 .11g or 802 .11b wireless network traffic, you will achieve the best N wireless performance with protected mode OFF . Conversely, in an environment with HEAVY 802 .11g or 802 .11b traffic or interference, you will achieve the best N wireless performance with protected mode ON . This will ensure N wireless performance is not affected . 802 .11e/WMM (Wi-fi Multimedia) Qos Setting the Router to this mode allows only 20MHz operation . This mode is compatible with N, draft 802 .11n-, 802 .11g-, and 802 .11b-compliant devices, but will limit N, draft 802 .11n-compliant devices bandwidth by half . Reducing bandwidth to 20MHz-only operation might solve some wireless problems . This is the default mode for the Router . WMM, based on 802 .11e QoS (Quality of Service), prioritizes important data on your network, such as multimedia content and voice-over-IP

(VoIP), so it will not be interfered with by other data being sent over the network . This feature requires other wireless devices, such as Wi-Fi phones or wireless laptops, to support WMM for best results . Using the broadcast ssId feature Note: This advanced feature should be employed by advanced users only . For security, you can choose not to broadcast your networks SSID . Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks . To turn off the broadcast of the SSID, remove the check mark from the box next to Broadcast SSID, and then click Apply Changes . The change is immediate . Each computer now needs to be set to connect to your specific SSID; an SSID of ANY will no longer be accepted . Refer to the documentation of your wireless network adapter for information on making this change . N Wireless Modem Router 44 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless security settings Your Router is equipped with the latest security standard called Wi-Fi Protected Access 2 (WPA2) and the legacy security standard called Wired Equivalent Privacy (WEP) . Your Router also supports the Wi-Fi Protected Setup (WPS) specification, which simplifies the setup of a wireless network . WPS uses familiar methodologies, such as typing in a Personal Identification Number (PIN) or pushing a button, to enable users to automatically configure network names and strong WPA2 data encryption and authentication . By default, your Router does not ship with security enabled . You may automatically configure the security settings using WPS . To change the security settings manually, you will need to determine which standard you want to use . To access the security settings, click Security on the Wireless tab . N Wireless Modem Router 45 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Using Wi-fi Protected setup WPS uses WPA2 (described below) for encryption . It does not provide additional security, but rather, standardizes the method for securing your wireless network . You may use either the Push Button Configuration

(PBC) method or PIN method to allow a device access to your wireless network . Conceptually, the two methods work as follows:

PBC: Push and hold the WPS button located on the front of your Router for three seconds . Then initiate the WPS procedure on the client device within two minutes . Refer to your clients documentation on this procedure . Pushing the PBC button will automatically enable WPS . The client has now been securely added to your wireless network . PIN: The client device has a PIN number (either four or eight digits) that is associated with WPS . Enable WPS through the GUI shown below . Enter the clients PIN into the Routers internal registrar (accessed through this GUI) . The client will be automatically enrolled into your wireless network within two minutes . N Wireless Modem Router 46 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 1 . Wi-Fi Protected Setup (WPS): Enabled or Disabled . 2 . Personal Identification Number (PIN) Method: In this method, a wireless client wishing to access your network must supply an 8-digit PIN to the Router . After clicking Enroll, you must start the WPS handshaking procedure from the client within two minutes . 3 . Router PIN: If an external registrar is available, you may enter in the Routers PIN to the registrar . Click Generate New PIN to change the PIN from the default value . Click Restore Default PIN to reset the PIN value . 4 . Push Button Configuration (PBC) Method: PBC is an alternate method to connect to a WPS network . Push the PBC button located on the front of the Router for three seconds, and then initiate the PBC on the client device . Alternatively, push the Start PBC soft button to start this process . 5 . Manual Configuration Method: This section lists the default security settings if not using WPS . The Router features WPA2, which is the second generation of the WPA-based 802 .11i standard . It offers a higher level of wireless security by combining advanced network authentication and stronger Advanced Encryption Standard (AES) encryption methods . IMPoRTaNT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2 . At the time of this User Manuals publication, a couple security patches are available, for free download, from Microsoft . These patches work only with the Windows XP operating system . Other operating systems are not supported at this time . WPa2 Requirements For Windows XP computers that do not have Service Pack 2 (SP2), a file from Microsoft called Windows XP Support Patch for Wireless Protected Access (KB 826942) is available for free download at http://support .microsoft .com/kb/826942 For Windows XP with Service Pack 2, Microsoft has released a free download to update the wireless client components to support WPA2

(KB971021) . The update is available from:

http://support .microsoft .com/kb/917021 IMPoRTaNT: You also need to ensure that all your wireless client cards/adapters support WPA2, and that you have downloaded and installed the latest driver . Most of the Belkin wireless cards have driver updates available for download from the Belkin support site:

www .belkin .com/networking . N Wireless Modem Router 47

UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting WPa/WPa2-Personal (PsK) Like WPA security, WPA2 is available in WPA2-Personal (PSK) mode . Typically, WPA2-Personal (PSK) is the mode that will be used in a home environment . Please refer to the User Manual for more information about wireless security and different types of wireless security . 1 . After youve set up your Router, go to the Security page under Wireless and select WPA/WPA2-Personal (PSK) from the Security Mode drop-down menu . 2 . For Authentication, select WPA-PSK, WPA2-PSK, or WPA-PSK +

WPA2-PSK . This setting will have to be identical on the wireless clients that you set up . WPA-PSK + WPA2-PSK mode will allow the Router to support clients running either WPA or WPA2 security . 3 . For Encryption Technique, select TKIP, AES, or TKIP+AES . This setting will have to be identical on the wireless clients that you set up . 4 . Enter your pre-shared key (PSK) . This can be from eight to 63 characters and can be letters, numbers, or symbols . This same key must be used on all of the wireless clients that you set up . For example, your PSK might be something like: Smith family network key . Click Apply Changes to finish . You must now set all wireless clients to match these settings . IMPoRTaNT: Make sure your wireless computers are updated to work with WPA2 and have the correct settings to get proper connection to the Router . N Wireless Modem Router 48 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting WPa security Note: To use WPA security, your wireless network cards must be equipped with software that supports WPA . At the time this User Manual was published, a security patch from Microsoft is available for free download . This patch works only with Windows XP . Your Router supports WPA-PSK . WPA-PSK uses what is known as a pre-shared key as the security key . A pre-shared key is basically a password that is between eight and 39 characters long . It can be a combination of letters, numbers, or characters . Each client uses the same key to access the network . Typically this is the mode that will be used in a home environment . setting WPa-PsK 1 . From the Security Mode drop-down menu, select WPA-PSK . 2 . For Encryption Technique, select TKIP or AES . This setting will have to be identical on the clients that you set up . 3 . Enter your pre-shared key . This can be from eight to 36 characters and can be letters, numbers, or symbols . This same key must be used on all of the clients that you set up . 4 . Click Apply Changes to finish . You must now set all clients to match these settings . N Wireless Modem Router 49 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting WeP encryption Note to Mac users: The Passphrase option will not operate with Apple AirPort . To configure encryption for your Mac computer, set the encryption using the manual method described in the next section . 1 . Select 128-bit WEP or 64-bit WEP from the drop-down menu . 2 . After selecting your WEP encryption mode, you can enter you WEP key manually by typing in the hex WEP key manually, or you can type a passphrase in the PassPhrase field and click Generate to create a WEP key from the passphrase . Click Apply Changes to finish . You must now set all of your clients to match these settings . 3 . Encryption in the Router is now set . Each of your computers on your wireless network will now need to be configured with the same passphrase . Refer to the documentation of your wireless network adapter for information on making this change . N Wireless Modem Router 50 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from AF and 09 . 64-bit keys are 10 digits long and can be divided into five two-digit numbers . 128-bit keys are 26 digits long and can be divided into 13 two-digit numbers . For instance:

af 0f 4b C3 d4 = 64-bit key C3 03 0f af 0f 4b b2 C3 d4 4b C3 d4 e7 = 128-bit key In the boxes below, make up your key by writing in two characters between AF and 09 . You will use this key to program the encryption settings on your Router and your wireless computers . Note to Mac users: Original Apple AirPort products support 64-bit encryption only . Apple AirPort 2 products can support 64-bit or 128-bit encryption . Please check your product to see which version you are using . If you cannot configure your network with 128-bit encryption, try 64-bit encryption . N Wireless Modem Router 51 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting MaC address Control The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network . Note: This list applies only to wireless computers . This list can be configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access . When you enable this feature, you must enter the MAC address of each client (computer) to which you want to allow network access . The Block feature lets you turn on and off access to the network easily for any computer without having to add and remove the computers MAC address from the list . setting up an allow access list 1 . Select the Allow radio button (1) to begin setting up a list of computers allowed to connect to the wireless network . 2 . Next, in the MAC Address field that is blank (2), type in the MAC address of the wireless computer you want to be able to access the wireless network, then click <<Add (3) . 3 . Continue to do this until all of the computers you want to add have been entered . 4 . Click Apply Changes (4) to finish .

(1)

(2)

(3)

(4) N Wireless Modem Router 52 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting up a deny access list The Deny Access list lets you specify computers that you DO NOT want to access the network . Any computer in the list will not be allowed access to the wireless network . All others will . 1 . Select the Deny radio button (1) to begin setting up a list of computers to be denied access to the wireless network . 2 . Next, in the MAC Address field that is blank (2), type in the MAC address of the wireless computer you want to deny access to the wireless network, then click <<Add (3) . 3 . Continue to do this until all of the computers you want to deny access to have been entered . 4 . Click Apply Changes (4) to finish .

(1)

(2)

(3)

(4) N Wireless Modem Router 53 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Configuring the firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including:

The firewall also masks common ports that are frequently used to attack networks . These ports appear to be stealth meaning that for all intents and purposes, they do not exist to a would-be hacker . You can turn the firewall function off if needed; however, it is recommended that you leave the firewall enabled . Disabling the firewall protection will not leave your network completely vulnerable to hacker attacks, but it is recommended that you leave the firewall enabled . IP Spoofing Land Attack Ping of Death (PoD) Denial of Service (DoS) IP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding Tear Drop Attack ICMP defect RIP defect Fragment flooding N Wireless Modem Router 54 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Configuring Internal forwarding settings Choosing an application The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network . Since your internal computers are protected by a firewall, computers outside your network (over the Internet) cannot get to them because they cannot be seen . A list of common applications has been provided in case you need to configure the Virtual Server function for a specific application . If your application is not listed, you will need to contact the application vendor to find out which port settings you need . Select your application from the drop-down list . Click Add . The settings will be transferred to the next available space in the screen . Click Apply Changes to save the setting for that application . To remove an application, select the number of the row that you want to remove then click Clear . Manually entering settings into the Virtual server To manually enter settings, enter the IP address in the space provided for the internal (server) machine, the port(s) required to pass (use a comma between multiple ports), select the port type (TCP or UDP), and click Apply Changes . You can only pass one port per internal IP address . Opening ports in your firewall can pose a security risk . You can enable and disable settings very quickly . It is recommended that you disable the settings when you are not using a specific application . N Wireless Modem Router 55 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting Client IP filters The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times . Restriction can be set for a single computer, a range of computers, or multiple computers . To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields

(1) . Next, enter 80 in both the port fields (2) . Select Both (3) . Select Block (4) . You can also select Always to block access all of the time . Select the day to start on top (5), the time to start on top (6), the day to end on the bottom (7), and the time to stop (8) on the bottom . Select Enable (9) . Click Apply Changes . The computer at the IP address you specified will now be blocked from Internet access at the times you specified . Note: Be sure you have selected the correct time zone under Utilities> System Settings> Time Zone .

(1)

(2)

(5)

(6)

(3)

(4)

(7)

(8)

(9) N Wireless Modem Router 56 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 setting MaC address filtering The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the network . Any computer attempting to access the network that is not specified in the filter list will be denied access . When you enable this feature, you must enter the MAC address of each client (computer) on your network to allow network access to each .

(1)

(2)

(3) To enable this feature, select MAC Address Filtering and click Enable MAC Address Filtering (1) . Next, enter the MAC address of each computer on your network by clicking in the space provided (2) and entering the MAC address of the computer you want to add to the list . Click Add (3), then Apply Changes (4) to save the settings . You can have a MAC-address-filtering list of up to 32 computers . Note: You will not be able to delete the MAC address of the computer you are using to access the Routers administrative functions (the computer you are using now) .

(4) N Wireless Modem Router 57 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 enabling the demilitarized Zone (dMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall . This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application . Use this feature on a temporary basis . The computer in the DMZ is NOT protected from hacker attacks . To put a computer in the DMZ, enter the last digits of its IP address in the IP field and select Enable . Click Apply Changes for the change to take effect . If you are using multiple static WAN IP addresses, it is possible to select which WAN IP address the DMZ host will be directed to . Type in the WAN IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, select Enable and click Apply Changes . N Wireless Modem Router 58 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Using dynamic dNs The Dynamic DNS service allows you to alias a dynamic IP address to a static host name in any of the many domains DynDNS .org offers, allowing your network computers to be more easily accessed from various locations on the Internet . DynDNS .org provides this service, for up to five host names, free to the Internet community . The Dynamic DNSSM service is ideal for a home website, file server, or to make it easy to access your home PC and stored files while youre at work . Using the service can ensure that your host name always points to your IP address, no matter how often your ISP changes it . When your IP address changes, your friends and associates can always locate you by visiting yourname .dyndns .org instead!

To register free for your Dynamic DNS host name, please visit http://www .dyndns .org .

(1) setting up the Routers dynamic dNs Update Client You must register with DynDNS .orgs free update service before using this feature . Once you have your registration, follow the directions below . 1 . Select DynDNS .org from the DDNS Service drop-down box (1) . 2 . Enter your DynDNS .org user name in the User Name field (2) . 3 . Enter your DynDNS .org password in the Password field (3) . 4 . Enter the DynDNS .org domain name you set up with DynDNS .org in the Domain Name field (4) . 5 . Click Update Dynamic DNS to update your IP address (5) . Whenever your IP address assigned by your ISP changes, the Router will automatically update DynDNS .orgs servers with your new IP address . You can also do this manually by clicking the Update Dynamic DNS button (5) . N Wireless Modem Router 59

(2)

(3)

(4)

(5) UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 blocking an ICMP Ping Computer hackers use what is known as pinging to find potential victims on the Internet . By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there . The Router can be set up so it will not respond to an ICMP ping from the outside . This heightens your Routers security level . To turn off the ping response, select Block ICMP Ping (1) and click Apply Changes . The Router will not respond to an ICMP ping . N Wireless Modem Router 60 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Utilities Restarting the Router The Utilities screen lets you manage different parameters of the Router and perform certain administrative functions . Sometimes it may be necessary to restart or reboot the Router if it begins working improperly . Restarting or rebooting the Router will NOT delete any of your configuration settings . N Wireless Modem Router 61 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Restarting the Router to Restore Normal operation 1 . Click the Restart Router button . 2 . The following message will appear . Click OK . 4 . A 60-second countdown will appear on the screen . When the countdown reaches zero, the Router will be restarted . The Router home page should appear automatically . If not, type in the Routers address

(default = 192 .168 .2 .1) into the navigation bar of your browser . 3 . The following message will appear . Restarting the Router can take up to 60 seconds . It is important not to turn off the power to the Router during the restart . N Wireless Modem Router 62 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 saving a Current Configuration You can save your current configuration by using this feature . Saving your configuration will allow you to restore it later if your settings are lost or changed . It is recommended that you back up your current configuration before performing a firmware update . 2 . A window will open that allows you to select the location where you want to save the configuration file . Select a location . You can name the file anything you want, or use the default name user .conf . Be sure to name the file so you can locate it yourself later . When you have selected the location and name of the file, click Save . 1 . Click Save . A window called File Download will open . Click Save . 3 . When the save is complete, you will see the window below . Click Close . N Wireless Modem Router 63 4 . The configuration is now saved . UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Restoring a Previous Configuration This option will allow you to restore a previously saved configuration . 1 . Click Browse . A window will open that allows you to select the location of the configuration file . All configuration files end with a

.conf . Locate the configuration file you want to restore and double-

click on it . 2 . You will be asked if you want to continue . Click OK . N Wireless Modem Router 64 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 3 . A reminder window will appear . It will take up to 60 seconds for the configuration restoration to complete . Click OK . 4 . A 60-second countdown will appear on the screen . When the countdown reaches zero, the Routers configuration will be restored . The Routers home page should appear automatically . If not, type in the Routers address (default = 192 .168 .2 .1) into the navigation bar of your browser . N Wireless Modem Router 65 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Updating the firmware From time to time, Belkin may release new versions of the Routers firmware . Firmware updates contain feature improvements and fixes to problems that may have existed . When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Routers firmware to the latest version . Checking for a New Version of firmware The Check Firmware (1) button allows you to instantly check for a new version of firmware . When you click the button, a new browser window will appear informing you that either no new firmware is available or that there is a new version available . If a new version is available, you will have the option to download it .

(1) N Wireless Modem Router 66 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 downloading a New Version of firmware If you click the Check Firmware button and a new version of firmware is available, you will see a screen similar to the one below:

1 . To download the new version of firmware, click Download . N Wireless Modem Router 67 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 A window will open that allows you to select the location where you want to save the firmware file . Select a location . You can name the file anything you want, or use the default name . Be sure to locate the file in a place where you can locate it yourself later . When you have selected the location, click Save . 2 . When the save is complete, you will see the following window . Click Close . 3 . The download of the firmware is complete . To update the firmware, follow the next steps in Updating the Routers Firmware . N Wireless Modem Router 68 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Updating the Routers firmware 1 . In the Firmware Update page, click Browse . A window will open that allows you to select the location of the firmware update file . The Update Firmware box will now display the location and name of the firmware file you just selected . Click Update . 2 . Browse to the firmware file you downloaded . Select the file by double-clicking on the file name . 3 . You will be asked if you are sure you want to continue . Click OK . N Wireless Modem Router 69 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 4 . You will see one more message . This message tells you that the Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted . Click OK . 5 . A 60-second countdown will appear on the screen . When the countdown reaches zero, the Router firmware update will be complete . The Router home page should appear automatically . If not, type in the Routers address (default = 192 .168 .2 .1) into the navigation bar of your browser . Changing system settings The System Settings page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Router . setting or Changing the administrator Password The Router ships with NO password entered . If you wish to add a password for greater security, you can set a password here . Write down your password and keep it in a safe place, as you will need it if you need to log into the Router in the future . It is also recommended that you set a password if you plan to use the remote management feature of your Router . N Wireless Modem Router 70 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 Changing the login Time-out setting The login time-out option allows you to set the period of time that you can be logged into the Routers advanced setup interface . The timer starts when there has been no activity . For example, imagine you have made some changes in the advanced setup interface, then left your computer alone without clicking Logout . Assuming the time-out is set to 10 minutes, 10 minutes after you leave, the login session will expire . You will have to log into the Router again to make any more changes . The login time-out option is for security purposes and the default is set to 10 minutes . Note: Only one computer can be logged into the Routers advanced setup interface at one time . setting the Time and Time Zone The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server . This allows the Router to synchronize the system clock to the global Internet . The synchronized clock in the Router is used to record the security log and control client filtering . Select the time zone that you reside in . You have the option to select a primary and a backup NTP server to keep your Routers clock synchronized . Select your desired NPT server from the drop-down box, or simply keep it as is . If you reside in an area that observes daylight saving, then place a check mark in the box next to Enable Daylight Saving . The system clock may not update immediately . Allow at least 15 minutes for the Router to contact the time servers on the Internet and get a response . You cannot set the clock yourself . N Wireless Modem Router 71 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 enabling Remote Management enabling/disabling UPnP Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD . Remote management allows you to make changes to your Routers settings from anywhere on the Internet . There are two methods of remotely managing the Router . The first is to allow access to the Router from anywhere on the Internet by selecting Any IP address can remotely manage the Router . By typing in your WAN IP address from any computer on the Internet, you will be presented with a login screen where you need to type in the password of your Router . The second method is to allow a specific IP address only to remotely manage the Router . This is more secure, but less convenient . To use this method, enter the IP address you know you will be accessing the Router from in the space provided and select Only this IP address can remotely manage the Router . Before you enable this function, it is STRONGLY RECOMMENDED that you set your administrator password . Leaving the password empty will potentially open your Router to intrusion . Advanced Feature: The Remote Access Port option allows you to configure the desired Remote Access Port for Remote Management feature . The default access port is set to port 8080 . UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router . It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant . Some applications require the Routers firewall to be configured in a specific way to operate properly . This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports . An application that is UPnP-compliant has the ability to communicate with the Router, basically telling the Router which way it needs the firewall configured . The Router ships with the UPnP feature enabled . If you want to disable this feature, simply select Disable in the UPnP Enabling section of the Utilities page . Click Apply Changes to save the change . N Wireless Modem Router 72 UsINg THe Web-based adVaNCed UseR INTeRfaCe table of contents sections 1 2 3 4 5 6 7 8 9 10 enabling/disabling auto firmware Update This innovation provides the Router with the built-in capability to automatically check for a new version of firmware and alert you that the new firmware is available . When you log into the Routers advanced interface, the Router will perform a check to see if new firmware is available . If so, you will be notified . You can choose to download the new version or ignore it . N Wireless Modem Router 73 MaNUally CoNfIgURINg NeTWoRK seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 Set up the computer that is connected to the cable or DSL modem FIRST using these steps . You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet . Manually Configuring Network settings in Mac os up to 9 .x 1 . Pull down the Apple menu . Select Control Panels and select TCP/IP . 2 . You will see the TCP/IP control panel . Select Ethernet Built-In or Ethernet in the Connect via: drop-down menu (1) . 3 . Next to Configure (2), if Manually is selected, your Router will need to be set up for a static IP connection type . Write the address information in the table below . You will need to enter this information into the Router .

(1)

(2) N Wireless Modem Router 74 MaNUally CoNfIgURINg NeTWoRK seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 4 . If not already set, at Configure:, choose Using DHCP Server . This will tell the computer to obtain an IP address from the Router . Manually Configuring Network settings in Mac os X 1 . Click on the System Preferences icon . 5 . Close the window . If you made any changes, the following window will appear . Click Save . Select Network (1) from the System Preferences menu . Restart the computer . When the computer restarts, your network settings are now configured for use with the Router .

(1) N Wireless Modem Router 75 MaNUally CoNfIgURINg NeTWoRK seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 3 . Select Built-in Ethernet (2) next to Show in the Network menu . 5 . If Manually is selected, your Router will need to be set up for a static IP connection type . Write the address information in the table below . You will need to enter this information into the Router .

(2)

(3)

(4)

(5) 6 . If not already selected, select Using DHCP next to Configure (4), then click Apply Now . your network settings are now configured for use with the Router . 4 . Select the TCP/IP tab (3) . Next to Configure (4), you should see Manually or Using DHCP . If you do not, check the PPPoE tab (5) to make sure that Connect using PPPoE is NOT selected . If it is, you will need to configure your Router for a PPPoE connection type using your user name and password . N Wireless Modem Router 76 MaNUally CoNfIgURINg NeTWoRK seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring Network settings in Windows 2000, NT, or XP 1 . Click Start, Settings, then Control Panel . 2 . Double-click on the Network and dial-up connections icon (Windows 2000) or the Network icon (Windows XP) . 3 . Right-click on the Local Area Connection associated with your network adapter and select Properties from the drop-down menu . 4 . In the Local Area Connection Properties window, click Internet Protocol (TCP/IP) and click the Properties button . The following screen will appear:

5 . If Use the following IP address (2) is selected, your Router will need to be set up for a static IP connection type . Write the address information the table below . You will need to enter this information into the Router . 6 . If not already selected, select Obtain an IP address automatically (1) and Obtain DNS server address automatically (3) . Click OK . your network settings are now configured for use with the Router .

(1)

(2)

(3) N Wireless Modem Router 77 MaNUally CoNfIgURINg NeTWoRK seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring Network settings in Windows 98 or Me 1 . Right-click on My Network Neighborhood and select Properties from the drop-down menu . 2 . Select TCP/IP -> settings for your installed network adapter . You will see the following window .

(1)

(3)

(2) 3 . If Specify and IP address is selected, your Router will need to be set up for a static IP connection type . Write the address information in the table below . You will need to enter this information into the Router . 4 . Write the IP address and subnet mask from the IP Address tab (3) . 5 . Click the Gateway tab (2) . Write the gateway address down in the chart . 6 . Click the DNS Configuration tab (1) . Write the DNS address(es) in the chart . 7 . If not already selected, select Obtain IP address automatically on the IP address tab . Click OK . Restart the computer . When the computer restarts, your network settings are now configured for use with the Router . N Wireless Modem Router 78 ReCoMMeNded Web bRoWseR seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 In most cases, you will not need to make any changes to your web browsers settings . If you are having trouble accessing the Internet or the Web-

Based Advanced User Interface, then change your browsers settings to the recommended settings in this section . Microsoft Internet explorer 4 .0 or Higher 1 . Start your web browser . Select Tools then Internet Options . 2 . In the Internet Options screen, there are three selections: Never dial a connection, Dial whenever a network connection is not present, and Always dial my default connection . If you can make a selection, select Never dial a connection . If you cannot make a selection, go to the next step . 3 . Under the Internet Options screen, click on Connections and select LAN Settings N Wireless Modem Router 79 ReCoMMeNded Web bRoWseR seTTINgs table of contents sections 1 2 3 4 5 6 7 8 9 10 4 . Make sure there are no check marks next to any of the displayed options: Automatically detect settings, Use automatic configuration script, and Use a proxy server . Click OK . Then click OK again in the Internet Options page . Netscape Navigator 4 .0 or Higher 1 . Start Netscape . Click on Edit then Preferences . 2 . In the Preferences window, click on Advanced then select Proxies . In the Proxies window, select Direct connection to the Internet . N Wireless Modem Router 80 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Installation CD does not automatically start . solution:

If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive . 1 . If the Setup Assistant screen does not appear within 1520 seconds, open up your CD-ROM drive by double-clicking on the My Computer icon that is located on your desktop . 3 . The Setup Assistant should start within a few seconds . If, instead, a window appears showing the files on the CD, double-click on the icon labeled SetupAssistant .exe . 2 . Next, double-click on the CD-ROM drive that the Setup Assistant Software CD has been placed in to start the installation . N Wireless Modem Router 81 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 4 . If the Setup Assistant still does not start, reference the section titled Manually Configuring Network Settings (page 74 of this User Manual) for an alternate setup method . Problem:

The Setup Assistant cannot find my Router . solution:

If the Setup Assistant is not able to find the Router during the installation process, please check the following items:

1 . If the Setup Assistant is not able to find the Router during the installation process, there may be third-party firewall software installed on the computer attempting to access the Internet . Examples of third-

party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall . If you do have firewall software installed on your computer, please make sure that you properly configure it . You can determine if the firewall software is preventing Internet access by temporarily turning it off . If, while the firewall is disabled, Internet access works properly, you will need to change the firewall settings to function properly when it is turned on . Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access . 2 . Unplug power to the Router for 10 seconds, and then plug the power back into the Router . Ensure that the Routers Power light is on; it should be solid green . If not, check to make sure that the AC adapter is correctly connected to the Router and plugged into a wall outlet . 3 . Ensure that you have a cable (use the cable included with the Router) connected between (1) the network (Ethernet) port on the back of the computer and (2) one of the LAN ports, labeled 1 through 4, on the back of the Router . Note: The computer should NOT be connected to the port labeled Modem on the back of the Router . 4 . Try shutting down and restarting your computer, then rerunning the Setup Assistant . If the Setup Assistant is still unable to find the Router, reference the section titled Manually Configuring Network Settings for installation steps . N Wireless Modem Router 82 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Problem:

The Setup Assistant cannot connect my Router to the Internet . solution:

If the Setup Assistant is not able to connect the Router to the Internet, please check the following items:

1 . Use the troubleshooting suggestions within the Setup Assistant . If the troubleshooting screen does not open automatically, click on the Troubleshoot button in the lower, right-hand corner of the Setup Assistant window . 2 . If your ISP requires a user name and password, make sure that you have typed in your user name and password correctly . Some user names require that the ISPs domain be at the end of the name . Example: myname@myisp .com . The @myisp .com part of the user name may need to be typed as well as your user name . If you continue to have no Internet connection, reference the section titled Manually Configuring Network Settings (page 74 of this User Manual) for alternate setup method . The Setup Assistant completed installation, but my web browser doesnt work . I am unable to connect to the Internet . The Routers Internet light is off and the Modem light is blinking . solution:

If you cannot connect to the Internet, the Internet light is off, and the Modem light is blinking, the problem may be that your modem and Router are not connected properly . 1 . Make sure the network cable between the modem and the Router is connected . We strongly recommend using the cable that was supplied with your cable or DSL modem for this purpose . The cable should be connected at one end to the Routers Modem port, and at the other end to the network port on your modem . 2 . Unplug the cable or DSL modem from its power source for three minutes . After three minutes, plug the modem back into its power source . This may force the modem to properly recognize the Router . 3 . Unplug the power to your Router, wait 10 seconds, and then reconnect the power . This will cause the Router to reattempt communication with the modem . If the Modem light on the Router is not lit after completing these steps, please contact Belkin Technical Support . 4 . Try shutting down and restarting your computer . N Wireless Modem Router 83 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Problem:

The Setup Assistant completed, but my web browser doesnt work . I am unable to connect to the Internet . The Modem light on my Router is blinking and the Internet light is solid . solution:

If the Modem light is blinking and the Internet light is solid, but you are unable to access the Internet, there may be third-party firewall software installed on the computer attempting to access the Internet . Examples of third-party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall . If you do have firewall software installed on your computer, please make sure that you properly configure it . You can determine if the firewall software is preventing Internet access by temporarily turning it off . If, while the firewall is disabled and Internet access works properly, you will need to change the firewall settings to function properly when it is turned on . Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access . If you are still unable to access the Internet after disabling any firewall software, please contact Belkin Technical Support . The Setup Assistant completed installation, but my web browser doesnt work . I am unable to connect to the Internet . The Routers Modem light is on and the Internet light is blinking . solution:

If you cannot connect to the Internet, the Modem light is on, and the Internet light is blinking, the problem may be that your connection type may not match the ISPs connection . If you have a static IP address connection, your ISP must assign you the IP address, subnet mask, and gateway address . Please refer to the section entitled Alternate Setup Method for details on changing this setting . If you have a PPPoE connection, your ISP will assign you a user name and password and sometimes a service name . Make sure the Router connection type is configured to PPPoE and the settings are entered properly . Please refer to the section entitled Alternate Setup Method for details on changing this setting . You may need to configure your Router to meet the specific requirements of your ISP . To search our Knowledge Base for ISP-specific issues, go to: http://web .belkin .com/support and type in ISP If you are still unable to access the Internet after verifying these settings, please contact Belkin Technical Support . N Wireless Modem Router 84 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I cant connect to the Internet wirelessly . solution:

If you are unable to connect to the Internet from a wireless computer, please do the following:

1 . Look at the lights on your Router . Your Belkin Routers lights should be as follows:

The Power light should be on . The Internet light should be on and not blinking . Problem:

3 . The exact window that opens will vary depending on the model of wireless card you have; however, any of the utilities should have a list of Available Networksthose wireless networks it can connect to . Does the name of your wireless network appear in the results?

Yes, my network name is listedgo to the troubleshooting solution titled I cant connect to the Internet wirelessly, but my network name is listed . No, my network name is not listedgo to the troubleshooting solution titled I cant connect to the Internet wirelessly, and my network name is not listed . The Modem light should be either on or blinking . 2 . Open your wireless utility software by clicking on the icon in the system tray at the bottom, right-hand corner of the screen . If you are also using a Belkin Wireless Card or Adapter with this Router, the tray icon should look like this I cant connect to the Internet wirelessly, but my network name is listed . solution:

If the name of your network is listed in the Available Networks list, please follow the steps below to connect wirelessly:

1 . Click on the correct network name in the Available Networks list . 2 . If the network has security (encryption) enabled, you will need to enter the network key . For more information regarding security, see the section entitled Securing your Wi-Fi Network in this User Manual . 3 . Within a few seconds, the tray icon in the lower, left-hand corner of your screen should turn green, indicating a successful connection to the network . N Wireless Modem Router 85 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I cant connect to the Internet wirelessly, and my network name is not listed . solution:

If the correct network name is not listed under Available Networks in the wireless configuration utility, please attempt the following troubleshooting steps:

1 . Temporarily move your computer, if possible, five to 10 feet away from the Router . Close the wireless configuration utility, and reopen it . If the correct network name now appears under Available Networks, you may have a range or interference problem . Please see the suggestions discussed in the section titled Placement of your Router for Optimal Performance in this User Manual . 2 . Using a computer that is connected to the Router through a network cable (as opposed to wirelessly), ensure that Broadcast SSID is enabled . This setting is found on the Routers wireless Channel and SSID configuration page . If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support . Problem:

My wireless network performance is inconsistent . Data transfer is sometimes slow . Signal strength is poor . I am having difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection . solution:

Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases . Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances . As a result, the typical indoor range of your wireless devices will be between 100 to 200 feet . Note also that connection speed may decrease as you move farther away from the Router or access point . In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, five to 10 feet away from the Router . N Wireless Modem Router 86 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Channel Depending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability . The default channel the Router is shipped with is channel 11 . You may choose from several other channels depending on your region (see the section titled Changing the Wireless Channel on page 43 for instructions on how to choose other channels) . limiting the Wireless Transmit Rate Limiting the wireless transmit rate can help improve the maximum wireless range, and connection stability . Most wireless cards have the ability to limit the transmission rate . To change this property, go to the Windows Control Panel, open Network Connections and double-click on your wireless cards connection . In the Properties dialog, select the Configure button on the General tab (Windows 98 users will have to select the wireless card in the list box and then click Properties), then choose the Advanced tab and select the rate property . Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable . Experiment with different connection rates until you find the best one for your environment; note that all available transmission rates should be acceptable for browsing the Internet . For more assistance, see your wireless cards user manual . Problem:

How do I extend the range of my wireless network?

solution:

Belkin recommends using one of the following products to extend wireless network coverage throughout large homes or offices:

These Belkin products are available at your local retailer, or can be ordered from Belkin directly . Wireless Access Point: A wireless access point can effectively double the coverage area of your wireless network . An access point is typically placed in the area not currently covered by your G Wireless Router, and is connected to the Router using either an Ethernet cable or through your homes power lines using two Powerline Ethernet Adapters . For 802 .11g (54g) wireless networks, Belkin offers a Wireless G Range Extender/Access Point that can be connected wirelessly to a Belkin G Wireless Router, without requiring an Ethernet cable or Powerline Ethernet Adapters . N Wireless Modem Router 87 For network/range extension information, please visit:

www .belkin .com/networking to find out more about:

Wireless G Range Extender/Access Point (F5D7130) Powerline Ethernet Adapter (F5D4070) Powerline USB Adapter (F5D4050) TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 4 . Click Apply Changes to finish . Encryption in the Wireless Router is now set . Each of your computers on your wireless network will now need to be configured with the same security settings . WaRNINg: If you are configuring the Wireless Router or Access Point from a computer with a wireless client, you will need to ensure that security is turned on for this wireless client . If this is not done, you will lose your wireless connection . Note to Mac users: Original Apple AirPort products support 64-bit encryption only . Apple AirPort 2 products can support 64-bit or 128-bit encryption . Please check your Apple AirPort product to see which version you are using . If you cannot configure your network with 128-bit encryption, try 64-bit encryption . Problem:

I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin Wireless Router or Belkin Access Point . solution:

1 . Log into your Wireless Router or Access Point . Open your web browser and type in the IP address of the Wireless Router or Access Point . (The Routers default is 192 .168 .2 .1, the Access Points default is 192 .168 .2 .254 .) Log into your Router by clicking on the Login button in the top, right-hand corner of the screen . You will be asked to enter your password . If you never set a password, leave the password field blank and click Submit . Click the Wireless tab on the left of your screen . Select the Encryption or Security tab to get to the security settings page . 2 . Select 128-bit WEP from the drop-down menu . 3 . After selecting your WEP encryption mode, you can type in your hex WEP key manually, or you can type in a passphrase in the Passphrase field and click Generate to create a WEP key from the passphrase . Click Apply Changes to finish . You must now set all of your clients to match these settings . A hex (hexadecimal) key is a combination of numbers and letters from AF and 09 . For 128-bit WEP, you need to enter 26 hex keys . For example:

C3 03 0f af 4b b2 C3 d4 4b C3 d4 e7 e4 = 128-bit key N Wireless Modem Router 88 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card (Wireless Network Card or Adapter) . solution:

The client card must use the same key as the G Wireless Router or access point . For instance, if your Wireless Router or access point uses the key 00112233445566778899AABBCC, then the client card must be set to the exact same key . 1 . Double-click the Signal Indicator icon to bring up the Wireless Network Utility screen . The Advanced button will allow you to view and configure more options of your client card . 2 . Once the Advanced button is clicked, the Belkin Wireless LAN Utility will appear . This Utility will allow you to manage all the advanced features of the Belkin client card . 3 . Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button . 4 . Under Data Encryption, select WEP . 5 . Ensure the box The key is provided for me automatically at the bottom is unchecked . If you are using this computer to connect to a corporate network, please consult your network administrator if this box needs to be checked . 6 . Type your WEP key in the Network key box . IMPoRTaNT: A WEP key is a combination of numbers and letters from AF and 07 . For 128-bit WEP, you need to enter 26 keys . This network key needs to match the key you assign to your G Wireless Router or access point . For example: C3030faf4bb2C3d44bC3d4e7e4 = 128-bit key 7 . Click OK, and then Apply to save the settings . If you are NOT using a Belkin wireless client card, please consult the manufacturers user manual for that wireless client card . Problem:

Do Belkin products support WPA?

solution:

Note: To use WPA security, all your clients must be upgraded to drivers and software that support it . At the time of this publication, a security patch download is available, for free, from Microsoft . This patch works only with the Windows XP operating system . Download the patch here:

http://www .microsoft .com/downloads/details .aspx?FamilyID=009d8425-

ce2b-47a4-abec-274845dc9e91&displaylang=en You also need to download the latest driver for your Belkin Wireless 802 .11g Desktop or Notebook Network Card from the Belkin support site . Other operating systems are not supported at this time . Microsofts patch only supports devices with WPA-enabled drivers such as Belkin wireless products . Download the latest driver at http://web .belkin .com/support N Wireless Modem Router 89 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a Belkin Wireless Router or Belkin Access Point for a home network . solution:

1 . From the Security Mode drop-down menu, select WPA-PSK . 2 . For Encryption Technique, select TKIP or AES . This setting will have to be identical on the clients that you set up . 3 . Enter your pre-shared key . This can be from eight to 63 characters and can be letters, numbers, symbols, or spaces . This same key must be used on all of the clients that you set up . For example, your PSK might be something like: Smith family network key . 4 . Click Apply Changes to finish . You must now set all clients to match these settings . Problem:

I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a Belkin client card (Wireless Network Card or Adapter) for a home network . solution:

Clients must use the same key that the G Wireless Router or access point uses . For instance, if the key is Smith Family Network Key in the G Wireless Router or access point, the clients must also use that same key . 1 . Double-click the Signal Indicator icon to bring up the Wireless Network Utility screen . The Advanced button will allow you to view and configure more options of your client card . 2 . Once the Advanced button is clicked, the Belkin Wireless LAN Utility will appear . This Utility will allow you to manage all the advanced features of the Belkin client card . 3 . Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button . 4 . Under Network Authentication, select WPA-PSK . 5 . Type your WPA key in the Network key box . IMPoRTaNT: WPA-PSK is a combination of numbers and letters from A-Z and 0-9 . For WPA-PSK, you can enter eight to 63 characters . This network key needs to match the key you assign to your G Wireless Router or access point . 6 . Click OK, then Apply to save the settings . Problem:

I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a Belkin client card (Wireless Network Card or Adapter) for a business . solution:

1 . Double-click the Signal Indicator icon to bring up the Wireless Network Utility screen . The Advanced button will allow you to view and configure more options of your client card . N Wireless Modem Router 90 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 2 . Once the Advanced button is clicked, the Belkin Wireless LAN Utility will appear . This Utility will allow you to manage all the advanced features of the Belkin client card . 3 . Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button . 4 . Under Network Authentication, select WPA . 5 . In the Authentication tab, select the settings that are indicated by your network administrator . 6 . Click OK, then Apply to save the settings . Problem:

I am having difficulty setting up Wi-Fi Protected Access (WPA) security and I am NOT using a Belkin client card for a home network . solution:

If you are NOT using a Belkin WPA Wireless Desktop or Wireless Notebook Network Card and it is not equipped with WPA-enabled software, a file from Microsoft called Windows XP Support Patch for Wireless Protected Access is available for free download:

http://www .microsoft .com/downloads/details .aspx?FamilyID=009d8425-

ce2b-47a4-abec-274845dc9e91&displaylang=en Note: The file that Microsoft has made available works only with Windows XP . Other operating systems are not supported at this time . You also need to ensure that the wireless card manufacturer supports WPA and that you have downloaded and installed the latest driver from their support site . supported operating systems:

Windows XP Professional Windows XP Home Edition enabling WPa-PsK 1 . In systems running Windows XP, click Start > Control Panel > Network Connections . 2 . Right-click on the Wireless Networks tab . The Wireless Network Connection Properties screen appears . Ensure the Use Windows to configure my wireless network settings box is checked . 3 . Under the Wireless Networks tab, click the Configure button, and you will see the client card properties screen . 4 . For a home or small business user, select WPA-PSK under Network Administration . 5 . Select TKIP or AES under Date Encryption . This setting will have to be identical to the G Wireless Router or access point that you set up . 6 . Type in your encryption key in the Network key box . IMPoRTaNT: Enter your pre-shared key . This can be from eight to 63 characters and can be letters, numbers, or symbols . This same key must be used on all of the clients that you set up . 7 . Click OK to apply settings . N Wireless Modem Router 91 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Whats the difference between 802 .11b, 802 .11g, 802 .11a, and draft 802 .11n?

Currently there are four levels of wireless networking standards, which transmit data at very different maximum speeds . Each is based on the designation for certifying network standards . The most common wireless networking standard, 802 .11b, transmits information at 11Mbps;

802 .11a and 802 .11g work at 54Mbps; and draft 802 .11n works at 300Mbps . See the following chart for more detailed information . Wireless Comparison Chart Wireless Technology g

(802 .11g) enhanced N MIMo N1 MIMo

(1x1 draft 802 .11n)

(draft 802 .11n with MIMo)

(draft 802 .11n with MIMo) speed/data Rate*

frequency Compatibility Up to 54Mbps*

Up to 150Mbps*

Up to 300Mbps*

Up to 300Mbps*

Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2 .4GHz Compatible with 802 .11b/g Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2 .4GHz Compatible with 802 .11b/g, draft 802 .11n, and Belkin G+ MIMO Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2 .4GHz Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2 .4GHz Compatible with draft 802 .11n and 802 .11b/g Compatible with draft 802 .11n and 802 .11b/g Coverage*

Up to 400 ft .*

Up to 600 ft .*

Up to 1,200 ft .*

Up to 1,400 ft .*

advantage Common widespread use for Internet sharing Better coverage and consistent speed and range Enhanced speed and coverage Leading edge best coverage and throughput

*Distance and connection speeds will vary depending on your networking environment . Technical support You can find technical support information at http://www .belkin .com/

networking or www .belkin .com/support/ . N Wireless Modem Router 92 TRoUblesHooTINg table of contents sections 1 2 3 4 5 6 7 8 9 10 Technical support You can find technical-support information on our website, www .belkin .com, by navigating to the tech-

support section . If you want to contact technical support by phone, please call the number you need from this list*:

*Local rates apply . CoUNTRy AUSTRIA BELGIUM NUMbe R 0820 200766 07 07 00 073 CZECH REPUBLIC 239 000 406 DENMARK FINLAND FRANCE GERMANY GREECE HUNGARY ICELAND IRELAND ITALY 701 22 403 097 25 19 123 08 - 25 54 00 26 0180 - 500 57 09 06 - 17 77 49 06 800 8534 0818 55 50 06 02 - 69 43 02 51 LUXEMBOURG 34 20 80 85 60 INTe RNeT adRess www.belkin.com/uk/networking/

www.belkin.com/nl/networking/

www.belkin.com/uk/networking/

www.belkin.com/uk/networking/

www.belkin.com/uk/networking/

www.belkin.com/fr/networking/

www.belkin.com/de/networking/

www.belkin.com/uk/networking/

www.belkin.com/uk/networking/

www.belkin.com/uk/networking/

www.belkin.com/it/networking/

www.belkin.com/uk/networking/

00800 - 44 14 23 90 www.belkin.com/uk/networking/

NETHERLANDS 0900 - 040 07 90 0.10 per minute www.belkin.com/nl/networking/

NORWAY POLAND PORTUGAL RUSSIA 81 50 0287 www.belkin.com/uk/networking/

00800 - 441 17 37 www.belkin.com/uk/networking/

707 200 676 495 580 9541 www.belkin.com/uk/networking/

www.belkin.com/networking/

SOUTH AFRICA 0800 - 99 15 21 www.belkin.com/uk/networking/

SPAIN SWEDEN 902 - 02 43 66 07 - 71 40 04 53 www.belkin.com/it/networking/

www.belkin.com/it/networking/

SWITZERLAND 08 - 48 00 02 19 www.belkin.com/uk/networking/

UNITED KINGDOM 0845 - 607 77 87 www.belkin.com/uk/networking/

OTHER COUNTRIES

+44 - 1933 35 20 00 N Wireless Modem Router 93 INfoRMaTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 EU DECLARATION OF CONFORMITY

esky

[Czech]

Dansk

[Danish]

Deutsch

[German]

Eesti

[Estonian]

English Espaol

[Spanish]

[Greek]

Franais

[French]

Italiano

[Italian]

Latviski

[Latvian]

[Belkin Ltd] tmto prohlauje, e tento [F5D8636-4] je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede [Belkin Ltd] erklrer herved, at flgende udstyr [F5D8636-4] overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt [Belkin Ltd], dass sich das Gert [F5D8636-4] in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab [Belkin Ltd] seadme [F5D8636-4] vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, [Belkin Ltd], declares that this [F5D8636-4] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por medio de la presente [Belkin Ltd] declara que el [F5D8636-4] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

[Belkin Ltd] [F5D8636-4]

1999/5/. Par la prsente [Belkin Ltd] dclare que l'appareil [F5D8636-4] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Con la presente [Belkin Ltd] dichiara che questo [F5D8636-4] conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o [Belkin Ltd Belkin Ltd ] deklar, ka [F5D8636-4 / iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi

[Lithuanian]

iuo [Belkin Ltd] deklaruoja, kad is [F5D8636-4] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands

[Dutch]

Malti

[Maltese]

Hierbij verklaart [Belkin Ltd] dat het toestel [F5D8636-4l] in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hawnhekk, [Belkin Ltd], jiddikjara li dan [F5D8636-4] jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar

[Hungarian]

Alulrott, [Belkin Ltd] nyilatkozom, hogy a [F5D8636-4] megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Polski

[Polish]

Niniejszym [Belkin Ltd] owiadcza, e [F5D8636-4] jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus

[Portuguese]

[Belkin Ltd] declara que este [F5D8636-4] est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Slovensko

[Slovenian]

[I Belkin Ltd] izjavlja, da je ta [F5D8636-4] v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky

[Slovak]

[Belkin Ltd] tmto vyhlasuje, e [F5D8636-4] spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. N Wireless Modem Router 94 Suomi

[Finnish]

[Belkin Ltd] vakuuttaa tten ett [F5D8636-4] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska

[Swedish]

Hrmed intygar Belkin Ltd] att denna [F5D8636-4] str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. slenska

[Icelandic]

Hr me lsir [Belkin Ltd] yfir v a [F5D8636-4] er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 1999/5/EC. Norsk

[Norwegian]

[Belkin Ltd] erklrer herved at utstyret [F5D8636-4] er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF. http://www .belkin .com/doc/

For information on product disposal please refer to http://environmental .belkin .com FoR Use in it no LV cH Lt BG At LU Ro Be Mt tR cY nL cZ PL DK Pt ee sK FR es ie Fi si Li oPeRAtes on cHAnneLs 1-13 GR GB HU is De se Restricted Use in certain countries class 2 equipment INfoRMaTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 belkin International, Inc ., limited lifetime Product Warranty What this warranty covers . Belkin International, Inc . (Belkin) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship . has been improperly installed, altered in any way, or tampered with . The Belkin Product Warranty does not protect against acts of God such as flood, earthquake, lightning, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i .e . brownouts or sags), non-authorized program, or system equipment modification or alteration . What the period of coverage is . Belkin warrants the Belkin product for the lifetime of the product . How to get service . What will we do to correct problems?

Product Warranty . Belkin will repair or replace, at its option, any defective product free of charge (except for shipping charges for the product) . Belkin reserves the right to discontinue any of its products without notice, and disclaims any limited warranty to repair or replace any such discontinued products . In the event that Belkin is unable to repair or replace the product (for example, because it has been discontinued), Belkin will offer either a refund or a credit toward the purchase of another product from Belkin .com in an amount equal to the purchase price of the product as evidenced on the original purchase receipt as discounted by its natural use . What is not covered by this warranty?

All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkins request at the sole expense of the purchaser, or if Belkin determines that the Belkin product N Wireless Modem Router 95 To get service for your Belkin product you must take the following steps:

1 . Contact Belkin Tech Support at the number listed on page 93, within 15 days of the Occurrence . Be prepared to provide the following information:

a . The part number of the Belkin product . b . Where you purchased the product . c . When you purchased the product . d . Copy of original receipt . 2 . Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim . INfoRMaTIoN table of contents sections 1 2 3 4 5 6 7 8 9 10 Belkin reserves the right to review the damaged Belkin product . All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser . If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment . The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser . Damaged equipment must remain available for inspection until the claim is finalized . Whenever claims are settled, Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have . How state law relates to the warranty . THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY . Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you . IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES . This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state . Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you . N Wireless Modem Router 96 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. in a residential installation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including that may cause undesired operation. interference FCC Part 68 REQUIREMENTS This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: BKCDL01BF5D7634V2. If requested, this number must be provided to the telephone company. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five

(5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US: BKCDL01BF5D7634V2. The digits represented by 01 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. If your equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC. Your telephone company may make changes in it is facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, Please contact the following address and phone number for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. COMPANY:

Belkin International, Inc. ADDRESS:

501 West Walnut Street, Compton, CA 90220-5221 TEL NO:

1 (310) 604-2315 Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, United Kingdom Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, France Belkin GmbH Hanebergstrasse 2 80637 Munich Germany Belkin Iberia C/ Anabel Segura, 10 planta baja, Of. 2 28108, Alcobendas, Madrid Spain Belkin Italy & Greece Via Carducci, 7 Milano 20123 Italy Belkin B.V. Boeing Avenue 333 1119 PH Schiphol-Rijk, Netherlands 2008 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Apple, AirPort, Mac, Mac OS, and AppleTalk are trademarks of Apple Inc., registered in the U.S. and other countries. Windows, Windows Vista, NT, and Microsoft are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries

. PM01527ea-C F5D8636-4