FCC ID: K7SF5U035 Wireless USB PC to PC adapter

Belkin Wireless USB P.C. to P.C. Adapter Model F5U035 Revision 0.25

- 1 -

Table of Contents Introduction ............................................................................... 3 Features ................................................................................. 3 Operating System Supported ..................................................... 3 System Requirements ............................................................... 3 Package Includes ..................................................................... 3 Technical Specification................................................................. 4 How to insert the Belkin Dongle to a computer ................................ 5 How to use the Belkin Dongles...................................................... 7 Install the Belkin Dongle Software .............................................. 9 Operating the Belkin USB Dongles ............................................... 15 How to use Belkin(R) WiMedia Manager........................................ 17 Uninstallation ........................................................................... 18 Uninstall Belkin(R) Wireless UWB Link Software.......................... 18 Uninstall Belkin(R) Wireless UWB Link Drivers ............................ 18 Uninstall Intel(R) UWB Device Firmware Utility (DFU) Driver (This may not be required) .............................................................. 18 Channel Selection ..................................................................... 19 Multi-Channel Operations ........................................................ 19 Troubleshooting ........................................................................ 20 Customer Support..................................................................... 20 Information.............................................................................. 20 FCC Statement ...................................................................... 20 Revision 0.25

- 2 -

Introduction Congratulations and thank you for purchasing the Belkin(R) Wireless USB 2.0 PC to PC Adapter. This revolutionary product lets you connect your computer or laptop wirelessly to other computers and perform operations such as fast file transfers, video streaming. Please review this User Manual carefully so that you are sure to get the most from your Wireless UWB Adapter. Features

- Wireless Connectivity between computers and or laptops.

- Connect almost instantly without any access point.

- Data transfer rate of up to 480 Mbps* at a distance of 3 meters away

- Data transfer rate of up to 110 Mbps* at a distance of 10 meters away

- Create your own Personal Area Network and exchange files, play videos Operating System Supported

- Microsoft* Windows Vista

- Microsoft* Windows XP with Service Pack 2 System Requirements

- Personal Computer with USB 2.0 port

- 128 Megabytes Physical Memory Note: Do not plug the Belkin dongle into USB port which is not USB 2.0. Package Includes

- Belkin(R) Wireless UWB Adapter (Qty 2)

- USB Flexible Connector (Qty 2)

- Installation CD-ROM

- User Manual Revision 0.25

- 3 -

Technical Specification Model Number UWB Chipset Antenna Operating Temperature Operating Range Power Mode PHY Data Rate Frequency Range RF Modulation PHY Compliance MAC Compliance FCC Compliance USB Compliance OS Compliance Co-existence F5U035 Alereon Baseband, RF Intel(R) Wireless UWB Link 1480M MAC On-board Omni-directional Antenna 00 C to 550 C Up to 30 Feet (10 Meters) USB Bus powered. 480 Mbps (Automatic Rate Adaptation) 3.1 GHz 4.8 GHz Supporting 3 sub-bands 528 MHz each Multiband OFDM Complies with WiMedia(R) PHY Specification Revision 1.0 Complies with WiMedia(R) MAC Specification Revision .85 Complies with FCC 47 CFR Part 15, Subpart F Section 15.519 Complies with USB 2.0 Specification Complies with Microsoft* Windows* XP SP2, Vista Coexists with other standard WiMedia devices Revision 0.25

- 4 -

How to insert the Wireless USB 2.0 PC to PC Adapter to a computer Insert the dongle into the USB adapter as shown in the diagram below. Insert the adapter with the dongle into the USB port of the computer. Belkin Wireless UWB Adapter Belkin USB Adapter Figure 1 How to Insert Dongle into USB Adapter B6473-01 Revision 0.25

- 5 -

Recommended ways to connect the adapter to a computer Figure 2 Recommended Dongle Orientation B6474-01 Revision 0.25

- 6 -

How to use the Wireless USB 2.0 PC to PC Adapter The Wireless USB 2.0 PC to PC Adapter can be used with laptops or desktop systems to communicate wirelessly. A few scenarios have been listed below to give you an idea of how the adapter can be used to share information almost instantly and improve your productivity. Figure 3 Laptop to Laptop Wireless Communication Figure 4 Laptop to Computer Wireless Communication B6476-01 Revision 0.25

- 7 -

Figure 5 Multi-Laptop communication creating a Personal Area Network B6477-01 Revision 0.25

- 8 -

Installation The following steps will illustrate the procedure to install the software and the Wireless USB 2.0 PC to PC Adapter for the first time. Note: Do not attach the USB dongle before the software is installed. Step 1 Install the software from the CD-ROM onto your computer. Step 2 Connect the USB dongle to the PC or laptop and complete the multi driver installation. Step 3 After successful installation, now you are ready to use the Belkin dongles for copying files, or streaming video. Install the Wireless USB 2.0 PC to PC Adapter Software 1. If this is not the first time the software has been installed, please uninstall the old version of the software. Click Start -> Control Panel -> Add or Remove Programs. In the Add or Remove Programs Window, scroll down to select Belkin(R) Wireless UWB Link software and click Remove button to delete the software. 2. Install the Wireless USB 2.0 PC to PC Adapter software by running the installation file setup.exe provided in a CD-ROM as part of the package. 3. If the system does not have Microsoft* .Net Framework, Version 2.0, the installation file will install .Net Framework first and then proceed to install the Belkin Wireless UWB Link software. 4. The InstallShield Wizard will be displayed as shown in the figure below. Click Next to proceed. Figure 6 InstallShield Wizard Revision 0.25

- 9 -

5. InstallShield Wizard will display the License Agreement Window as shown below. If you agree to use the software, Click I agree the terms in the License Agreement and Click Next to proceed. Figure 7 InstallShield License Agreement 6. InstallShield will display the Ready to Install the Program window as shown below. Click Install to proceed. Figure 8 InstallShield Ready to Install the Program 7. The InstallShield wizard will display a warning message The Software you are installing has not passed Windows Logo testing to verify its compatibility with Windows XP. This message can be safely ignored, as this will not cause any harm to your system. Proceed with the installation by clicking Continue Anyway. Revision 0.25

- 10 -

Figure 9 InstallShield Warning Message 8. InstallShield will prompt two more times with the warning message, Click Continue Anyway. 9. Now the InstallShield has completed the installation of the Belkin Wireless UWB Link software as shown in the figure below. Click Finish to close the Window. Figure 10 InstallShield Wizard Completed 10. At this point, WiMedia Manager will be running on the Notification Area of the Windows Status bar as shown in the figure below. Figure 11 WiMedia Manager 11. After successful installation, the Belkin Wireless UWB Link software will be copied into the default folder location C:\Program Files\Belkin\Wireless UWB Link. Revision 0.25

- 11 -

12. Now insert the Belkin dongle to the USB 2.0 port of the personal computer. 13. Windows* will recognize a new hardware plugged into the system and invoke Found New Hardware Wizard prompting to install the software for Intel(R) Wireless UWB Link 1480M Device Firmware Utility. Figure 12 Found New Hardware - Intel(R) Wireless UWB Link 1480M Device Firmware Utility 14. Choose Yes, this time only and Click Next to proceed. Figure 13 Found New Hardware Wizard 15. Found New Hardware Wizard will prompt you to insert installation CD or floppy disk. Choose the option Install the Software automatically (recommended) and click Next to proceed. Revision 0.25

- 12 -

Figure 14 - Found New Hardware Wizard Prompting to Insert installation CD 16. Found New Hardware Wizard will display a warning message. This message can be safely ignored and click Continue Anyway to proceed. 17. Now the Found New Wizard has installed the software Intel(R) Wireless UWB Link 1480M Device Firmware Utility. Click Finish to close the Window. Figure 15 - Found New Hardware Wizard Completed Software Installation 18. Windows will recognize a new hardware plugged into the system and invoke Found New Hardware Wizard prompting to install the software for Intel(R) Wireless UWB Link 1480M Control Driver. Repeat the same steps as followed with the first software installation. 19. Windows will recognize a new hardware plugged into the system and invoke Found New Hardware Wizard prompting to install the software for Intel(R) Revision 0.25

- 13 -

Wireless UWB Link 1480M USB WiNet Adapter. Repeat the same steps as followed with the first software installation. 20. After the software installation, Windows will prompt the New Hardware is ready to use as shown in the figure below. Figure 16 Found New Hardware Wizard New Hardware ready to use 21. To verify installation, go to the device manager by clicking Start Menu -> Control Panel -> System (Under Classical View) -> Choose Hardware Tab -> Click Hardware profiles at the bottom of the window. 22. Look for the devices Intel(R) Wireless UWB Link 1480M Control Driver and Intel(R) Wireless UWB Link 1480M USB WiNet Adapter listed as indicated in the figure below. Figure 17 Device Manager displaying Control and Network drivers Revision 0.25

- 14 -

Operating the Belkin USB Dongles Figure 18 End-to-End Connectivity with Belkin USB Dongles 1. Boot the PCs Laptop A and laptop B to Windows*. 2. Ensure the WiMedia Manager is running by viewing the WiMedia Manager icon on the Notification Area on the Status bar of Windows. 3. Open the WiMedia Manager by double clicking the WiMedia Manager. 4. Under General Tab, Ensure the channel numbers are the same for Laptop A and laptop B. 5. Insert the Belkin dongle on the USB port of Laptop A as well as Laptop B. 6. The Belkin dongle will be enumerated as a USB device under normal operations for respective laptops as indicated in the Figure 17. 7. In General View, the remote UWB device will be listed under the UWB Neighbourhood column. Revision 0.25

- 15 -

Figure 19 WiMedia Manager listing remote devices 8. To Connect to the remote device, select the remote device and click Connect. Similarly perform the same action on the remote PC. 9. Upon successful connection, the Windows* notification bar would indicate Local Area Connection # Connected (Note 1). Figure 20 WiMedia Manager When UWB Device is Connected 10. Now you can copy files or share a video at a very fast speed!

Revision 0.25

- 16 -

How to use Belkin(R) WiMedia Manager The Belkin WiMedia Manager is installed as a startup item as part of the Belkin Wireless UWB Link software installation and will be running as a background task. The WiMedia Manager can be located on the notification area of the Microsoft*

Windows status bar as shown in the Figure 21. Figure 21 WiMedia Manager on the Notification Area The WiMedia Manager is functionally classified into General View and Advanced View as illustrated in the figure below. The General View will list the features:

Device Status RADIO ON/OFF Establish UWB Connections, disconnect a UWB Connection, Change channel numbers, Scan for UWB Devices Listing of Software/Firmware version for maintenance purpose The Advanced View will list the features:

Bandwidth Reservation Power Management Statistics for existing UWB Connections Figure 22 WiMedia Manager General and Advanced View Revision 0.25

- 17 -

Uninstallation If you need to uninstall the software, follow the procedure outlined below. Uninstall Belkin(R) Wireless UWB Link Software Please follow the steps indicated below to uninstall the Belkin(R) Wireless UWB Link software which was installed prior:

1. Go to Add or Remove Programs by clicking Start Menu -> Control Panel -> Add or Programs 2. Identify Belkin(R) Wireless UWB Link software and Click the Remove button to Uninstall 3. The Install Shield wizard will ask Do you want to completely remove the selected application and its features? Click the Yes button. 4. After successful Uninstall, the Uninstall Complete Dialog will be displayed. Click the Finish button to close the dialog. Uninstall Belkin(R) Wireless UWB Link Drivers The following sequence of un-installation of the drivers is recommended.

- Intel(R) Wireless UWB Link 1480M USB WiNet Adapter

- Intel(R) Wireless UWB Link 1480M Control Driver 1. Insert the Belkin dongle into the USB port of the personal computer/laptop. 2. Go to the Device Manager. 3. Under Network Adapters:

- Right Click on Intel(R) Wireless UWB Link 1480M USB WiNet Adapter and select Uninstall. 4. Under Universal Serial Bus Controller:

- Right Click on Intel(R) Wireless UWB Link 1480M Control Driver and select Uninstall. Uninstall Intel(R) UWB Device Firmware Utility (DFU) Driver (This may not be required) The DFU device is not listed in the Device manager, we recommend to delete the file DfuUWB.sys from the location C:\Windows\System32\drivers. Revision 0.25

- 18 -

Channel Selection The Belkin(R) dongle will operate in Band Group 1 mode only. The channels supported within the Band Group1 are listed in the Table 1. If there are multiple dongles, you may choose to operate the dongles in different channels for simultaneous operations. The default channel Belkin dongle is programmed to operate in channel number 14. Channel Number TFC Code Band ID 9 10 11 12 13 14 15 1 2 3 4 5 6 7 1 2 3 1 2 3 1 3 2 1 3 2 1 1 2 2 3 3 1 1 3 3 2 2 1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 Table 1 PHY Channel Numbers Multi-Channel Operations If theres a need to have simultaneous UWB connections, you may choose to operate these systems in different channel numbers without any interference. Before inserting the Belkin dongles, open the WiMedia Manager and change the channel number appropriately. Revision 0.25

- 19 -

Troubleshooting 1. Why does the Belkin Dongle not work on laptops which have USB 1.0/1.1 ports?

The Belkin dongle is designed to work for USB 2.0 and hence you can see the performance greater than USB 1.0/1.1. 2. Does your computer support USB 2.0?

To determine if your computer supports USB 2.0, follow the steps below:

Step 1: Go to the Device Manager Start -> All Programs -> Control Panel -> System ->

Hardware (Tab) -> Click Device Manager. Step 2: In Device Manager, Under Universal Bus Controllers check for the entry Enhanced Host Controller. Customer Support FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this device not expressly approved Belkin could void the users authority to operate the equipment under the FCC grant of equipment authorization issued to Belkin Information Electromagnetic Interference (EMI) is any signal or emission, radiated in free space or conducted along power or signal leads, that endangers the function of radio navigation or other safety service (the telephone and cellphones are considered to be safety services) or seriously degrades, obstructs or repeatedly interrupts a licensed radio communications service. Radio communications services include but are not limited to: AM/FM commercial broadcast, television, cellular services, radar, air traffic control, pager and personal communications services (PCS). These licensed services, along with unintentional radiators such as digital devices, including computer systems, contribute to the electromagnetic environment. Electromagnetic Compatibility (EMC) is the ability of items of electronic equipment to function properly together in the electromagnetic environment. While this device has Revision 0.25

- 20 -

been designed and determined to be compliant with regulatory agency limits for EMI, there is no guarantee that interference will not occur in a particular installation. If this device does cause interference with radio communications services, which can be determined by turning the device on and off, you are encouraged to try to correct the interference by one or more of the following measures:

Re orient the receiving antenna Relocate the device with respect to the victim receiver Move the device away from the victim receiver Plug the device host into a different power outlet than the victim receiver so that the device system and receiver are on separate branch circuits If necessary, consult your system service representative or an experienced radio/television technician for additional help in resolving interference. Revision 0.25

- 21 -