Settings & Programming Press and hold the MRK and SEN buttons to access Programming. To exit Programming, simply wait a few seconds without pressing a button. The unit will display Completed to confirm your selections. Press MRK to go from one category to the next User Mode Advanced Novice Pilot Scanning"
Full Word Press VOLUME + or - to change your setting within a category Access and customize all Settings and Programming Access and customize units and display color, (all other Settings are set to factory defaults) NOTE Switch to advanced mode to view all settings Scanning Bar with Full Word Full Word: AutoScan, Auto NoX, or Highway Display Color Blue/Green/Red/Amber Set color to match your vehicle's dash display Speed Display On Off Displays current speed Displays battery voltage Offers double beep alert tones below specified speed Speed Mute Off /20-160 mph 20 mph Over Speed Off /20-160 mph Reminds you when you exceed a specified speed Signal Strength Meter Standard 70 mph Tech Threat Basic Tones Standard Mild AutoMute On/ Off AutoLock On/ Off Units English/Metric Voice On/ Off GPS Filter On"/ Off AutoPower Off 1 Hour 2 Hours 4 Hours 8 Hour Bands Default Modified Press SEN to go from one Band category to the next X Band On/ Off K Band On/ Off Ka Band On/ Off Ka-POP On/Off Laser On/ Off TSR On"/ Off Markers Default Modified Press SEN to go from one Marker category to the next Other On"/Off Redlight On/ Off Red &Speed On/ Off Speed Cam On/ Off Speed Trp On/ Off Air Patrol On/Off Single band with bar graph of signal strength Single band with numeric frequency Multiple bands with bar graph of signal strengths Basic messages replace bands:
Caution (if traveling below Speed Mute limit) Slow Down (if traveling above Speed Mute limit) Standard Beltronics alert tones Mild alert tones Automatically reduces audio during alert Automatically stores and locks out false alarms Units for distance and speed Voice announcements Enables GPS-powered features Power turns on or off depending on your vehicle's ignition type (constant power or switched) Powers off automatically after 1 hour Powers off automatically after 2 hours Powers off automatically after 4 hours Powers off automatically after 8 hours NOTE If AutoPower is on, the display screen goes blank after 30 minutes to save screen life. Display screen will turn on automatically after you reach 10 MPH Default settings for North America Customize the bands you want to monitor Press VOLUME + or - to change your setting within a category Automatically rejects traffic flow sensors-monitoring false alarms Default settings Customize the types of locations you want to be alerted to to change your setting within a category Press VOLUME + or Other location Red light camera Red light & speed camera Speed camera Speed trap Air patrol Clear Locations Marked Lockouts Defender Format Clear all user Marked locations. Press SEN button to confirm Clear all lockouts. Press SEN button to confirm Clear all Defender data. Press SEN button to confirm Clear Defender database, all markers, and all lockouts. Press SEN button to confirm
"Default Setting FCC NOTE: Modifications not expressly approved by the manufacturer c?uld void the user's FCC granted authority to operate the equipment. FCC ID: QL4G7M5. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Using GT-7 1. Plug small end of SmartCord into modular jack on GT-7 and large end of SmartCord into your car's lighter/accessory socket. 2. GT-7 should power on automatically. If not, press the device's power button. Earphone Jack Connects to optional 3.5 mm stereo earphone odular Jack Connects to SmartCord for powering your device ini USB Jack Connects to your computer via USB Almini B cable for downloading software updates Using SmartCord Mute Button: Press to mute an alert; press three times to lock out a false alert; press twice while receiving a locked-out alert to unlock. Alert Light: Blinks orange when receiving an alert. Power Light: Lights blue when receiving power. Modular Connector Plugs into detector jack Lighter Adapter Connects to lighter/acce wry 'ocket