FCC ID: 2A3ET-REEVO Bicycle with Electric Drive (Pedelec)

Welcome To The Family Whats in the box?

Crank arms and pedals 6mm and 4mm Allen key Reevo Battery Battery charger Battery keys User manual Crank bolts Fender set

(Optional) Electronic bell

(Optional) Beno bag

(Optional) Rear light Ambient light sensor Wheel lock USB Charging Port Battery Motor Storage hook Front light Assembly Step 1 Remove your Reevo out of the box. Step 2 Fully extend the kickstand for ease of assembly. Your Reevo is packaged with the handlebar parallel to the wheels and frame. Step 3 Stand in front of the bike and face the bike. Align the front wheel so that it is parallel to the frame. Step 4 Hold the front wheel firmly in between your knees and rotate the handlebar anticlockwise until it is perpendicular to the frame. Step 5 Use the 6mm Allen key to tighten the top bolt of the bike stem. Step 6 Use the 4mm Allen key to tighten the two side bolts of the bike stem. Tighten the top bolt first before tightening the side bolts. The left crank arm and right crank arm are different. You can differentiate them by identifying the L and R markings. L is for the left crank arm. R is for the right crank arm. Step 7 Insert the right crank arm followed by a crank bolt into the right side of the housing by hand. Step 8 Use the 6mm Allen key to tighten the crank bolt. Repeat the steps above for the left crank arm. Step 9 Adjust the saddle height to fit your comfort. The optimum saddle height is when there is a slight bend in your leg with the pedal in its lowest position. Step 10 Press on both sides of the battery lid simultaneously to unlatch and open it. Step 11 Insert a nano SIM card into the SIM slot on the battery dock. We recommend using a 4G SIM card with a minimum data of 100 MB. Step 12 Insert the fully charged battery and close the battery lid. Technical Specifications Bike Weight 22.3 kg / 55 lbs Wheel Size 27.5(650b) Motor Power 250W (EU) / 750W (US) Top Speed 25km/h (EU) / 20mph (US) Available Size S/M (52 59) &

M/L (59 63) Battery Type Lithium Ion Battery Capacity 48V, 10.5 Ah Charge Time 3 hours Range 60 km/ 37 miles Geometry E F A B H G C D I Wheel Size 27.5 (650b) A Seat Tube 48.2 cm / 19.0 B Seat Tube Angle 71.9 C Head Tube Length 10.1 cm / 4.0 D Head Angle 69.6 E Effective Top Tube 65.0 cm / 25.6 F Bottom Bracket Drop 4.4 cm / 1.7 G Chainstay Length 43.3 cm / 17 H Wheelbase 113.37 cm / 44.6 I Standover 59.1 cm / 23.3 Stem Length 35 (S/M), 50 (M/L), 65(XL)*

Bike Maintenance and Safety Do not tamper or attempt to modify the bikes motor or integrated computer systems. Modifying them in anyway will void your warranty and may lead to accidents resulting in injury or even death. Bicycle safety is important. Wear a helmet when riding the bike especially in heavy traffic. Failure to do so may result in serious injuries or even death. Do not use cell phones while riding your bike. Always make sure the lights are working properly and not obscured in any way especially in dark conditions. Regular inspection and maintenance of the bike is important. Routinely check the brakes, tires, battery, wheel rims, handlebar Poor maintenance of the bike can cause parts to break, fail or malfunction, leading to serious injuries or even death. post. seat and is your It responsibility to acquaint yourself with the laws of the country where you ride and to comply with all the applicable laws, including properly equipping yourself and your bike as the law requires. Battery Care Battery is heavy. Handle it with care. Do not drop it to prevent injuries to yourself or damage the battery. Remove the battery from the bike if you do not intend to use it for a long time. Do not expose the battery and charger to blazing sunlight during charging. Always charge the battery in ambient temperatures. leaving Avoid prolonged periods. the battery discharged for Always keep the battery connector clean and dry. Charge the battery indoors only and ensure the battery and charger are placed on a non flammable surface when charging. Keep the battery and charger away from moisture and water during charging. Only use the Reevo battery charger to charge the battery. The battery will have a shorter battery life during winter and that is normal. Keep the battery and charger away from fire and heat. Keep the battery and charger away from fire and heat. Keep the battery and charger out of reach of children. Warranty Beno ensures your Reevo against defects in workmanship and material for 2 years for Europe and 1 year for the rest of the world . All original components of the bike are covered by a warranty for a period of 2 years for Europe and 1 year for the rest of the world from the date of delivery. This warranty applies only to original owners and is not transferable. Claims under this warranty can be made to the place at which you purchased your Reevo or directly to Beno and proof of purchase is required. The warranty does not cover:

Improper or negligent use, operation or modification of the product and its components. Normal wear and tear of drive train, brake pads, wheels, rollers, normal battery deterioration, etc. Damages or defects due to accidents. Improper assembly or installation of the product by the user. Follow up maintenance. Disclaimer Under no circumstances, including, but not limited to negligence, shall Beno or any Beno distributor (seller) be liable for any damages, limited to special or including but not consequential damages that result from the use of, or the inability to use, the Reevo bike and/or any other products or materials referred to in this manual, even if Beno has such been advised of damages. the possibility of Applicable law may not allow the limitation or liability or of exclusion consequential above damages, limitation or exclusion may not apply to you. incidental the so or FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

SIZE:70*50mm This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation MODEL: Reev0 FCC ID: 2A3ET-REEVO

Beno, Inc. Agent Authorization Company: Beno, Inc. Address: 651 N Broad St, Middletown, 19709, New Castle Delaware United States of America. Product Name: Bicycle with Electric Drive (Pedelec) Trade Mark: Beno Model Number(s): Reevo FCC ID: 2A3ET-REEVO We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Alec Lim Title:

manager Company: Beno, Inc. Date: 2021-11-02

Beno, Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-11-02 Subject; Request for Confidentiality FCC ID: 2A3ET-REEVO To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM Software Security Requirements Tune up In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name / Title: Alec Lim / manager Company: Beno, Inc. Address: 651 N Broad St, Middletown, 19709, New Castle Delaware United States of America. Phone: (016) 461-4919 Fax: (016) 461-4919 E-Mail: angelinazhang@zctc-lab.com