ThankyouformakingBENROyourchoicefor professionalphotographic equipmentYourBENROgearis manufacturedtoprovideyearsof dependableserviceInordertoobtainoptimumsatisfactionandperformance wesuggestthatyoucarefullyreadtheseinstructions
2 1 10 3 8 9 7 12 4 5 6 7 11 14 13 15 24 16 17 23 22 21 20 18 19 3.1 1.1
HDMI Video Output
HDMI high definition support
External Expand Cable Slot
Microphone Support
Single Hand Handle
Right Handle
Locking Knob
Rotation Arm
Locking Knob
Safety Button
Left Handle
Horizontal Lock Knob
Vertical Arm
Roll Axis Lock Knob
Horizontal Arm
Tilt Axis Lock Knob
Tilt Arm
Quick Release Plate
Sliding Camera Plate
Camera Support
Sliding Base Lock Knob
Safety Button
QR Plate Lock Knob
Lens Support
External Expand Cable
Camera Specs Display
Dial Disk
Dial Rod
Joystick
Microphone Support
Gimbal and Camera Status LED Light REDDOG R2PRO OPERATING INSTRUCTIONS
Microphone Support 25 26 28 29 30 31 32 27 33 34
Zooming Button
Shutter Button
ON/OFF Button
Recording Button
Control Button Introduction
Joystick In select gimbal modes the Joystick will move the camera up, down, left and right
Recording Button Press to record
Shutter Button:
Press to take photos
Zooming Button:
Zoom in and zoom out
On/Off Pull down to turn on and pull up to turn off. Pulling the lever down once turns on the gimbal. To change the shooting modes pull down additional times to activate these shooting modes: All Follow, Horizontal Follow and Lock Mode. The Gimbal and Camera Status LED Light:
Low power status: Red Changing Mode LED light Blinking Status Blue: Lock mode Orange: horizontal follow mode Purple: all follow mode RedDog R2PRO LED Color Definition 1.Blue light blinking: Bluetooth is pairing. Pull down (towards on) and hold down the power button for 5 seconds . This enables blue tooth pairing. The blue light starts to blink. 2.Blue light is always on: APP paired with the gimbal. 3.Blue light is blinking fast: hardware is upgrading Gimbal Working Mode 1.Blue light is always on: lock mode 2.Orange light is always on: horizontal follow mode 3.Purple light is always on: all follow mode 4.Red light is always on: Low battery power
Camera Specs Adjustment 1.You can adjust the camera specs by rotating the Dial Disk and switch to next specs by pressing it. 2. You can focus the camera by pushing up and down the Dial Rod. a
c b
d
f h
e g i
j
4545 OPERATING INSTRUCTIONS Install Battery (Figure 1) Please charge the battery before use. Unscrew the handle and put 3 pieces of 26350 batteries inside. Screw the cap. Note: please install the batteries in the correct polarity. The RedDog R2 pro must be used with the correct batteries (26350). Using other batteries may damage the unit. Install Camera (Figure 2, 3) 1.Install the QR plate on the camera and tighten the knob a clockwise. Then mount the QR plate onto the sliding base to move the plate. Put the gravity center of camera on the center of gimbal. Then tighten the knob b clockwise. Note: If you need to remove the QR plate, you should loosen the lock knob b, press and hold safety button c. There is unique memory lock block d on the QR plate. You can record the corresponding balance position of camera in order to use directly next time. Balance Adjustment (Figure 4, 5, 6, 7) 1. Adjust the sliding plate according to the camera size. Make the camera lens stay at front and horizontally. Loosen the lock knob e at the bottom of sliding plate. Slides left and right the camera and keep it 5mm away from the camera support 2.The balance adjustment of the tilt axis. Position the camera pointing upwards; Loosen the screw f (about three rounds); and then move the Fixed Camera Plate to allow the camera to stay vertical to the ground. Make sure to lock the screw f after adjustment is complete. 3.The balance adjustment of roll axis. Position the camera to point forwards; Loosen the screwg (about three rounds); and then adjust the horizontal arm to keep the horizontal status to the ground when the horizontal arm is static. Make sure to lock the screwg after completed the adjustment. 4.The balance adjustment of the Pan axis. Loosen the screwh; adjust the vertical arm to keep the horizontal status with the ground when the vertical arm is static. Make sure to lock the screw h after the adjustment is complete. All adjustments completed. High/Low Position Interchange (Figure 8, 9) The under-slung position takes less effort when shooting at low angles or shooting for long period of time. 1.Loosen the knobI clockwise, and then rotate the left and right handle to be 180 degree clockwise. Fix the knobI counter clockwise to complete the handle positioning. Change to Single Handle Position (Figure 10, 11, 12) 1. Mount the single handle to the rotation arm bracket. Rotate the triangle position of the rotation arm bracket. It needs to align with the single handle. Then rotate knob j clockwise till tighten it to finish the change. Quick Storage (Figure 13, 14) 1.Loosen the knobk counter clockwise and pull the safety button to the UNLOCK port at the same time to rotate fold the rotation arm. 2.The gimbal comes with a storage case, which allows quick storage of the gear. It is portable. Roll Shooting (Figure 15) 1.When the LED light is in purple operation mode, open the roll button at the upper right corner on APP to start the roll follow mode 2.Under this mode, when you tilt the camera, the gimbal will follow this movement. Panoramic Shooting (Figure 16) 1.Turn on the gimbal and adjust the gimbal to move the camera to shooting position (shutter cable needs to be connected). 2.Connect the APP to the gimbal 3.Specs setting for panoramic shooting: (a) Set photo numbers (b) Set photography angle span (c) Confirmed. Start taking photos. Motion Time Lapse (Figure 17) 1.When the LED light is in purple operation mode, open the roll button at the upper right corner on APP to start the roll follow mode. 2.Connect the APP to the gimbal: (a) Set time-lapse specs (b) Describe photography track (c) Preview photography track (d) Confirmed. Start taking photos. Note:
1.When the exposure time is set to automatic, the camera needs to be at M stop. Otherwise it will fail to take pictures because it is unable to focus. 2.When the exposure time is set to automatic, the camera needs to be at the slow shutter mode. When you power up the gimbal, use the on/off switch to select the shooting modes. Horizontal Follow Mode The lens will move horizontally with the movement of the handle left and right. All Follow Mode The tilt and pan direction of the lens will move with the movement of the handle up and down, left and right. Lock Mode The lens will keep in one direction no matter how handle moves.
26350
1
Bluetooth Version V4.1 (BLE mode) Frequency Range: 240 -2480MHz 2
Specifications
Gimbal
Working time
Working Voltage
Working Electric Flow
Working Temperature:
Product Size (W*D*H)
Product Weight
Tilt Axis Mechanical Moving Range
13h
9 Minimum 9V
Standard 11.1V
Maximum: 12V
220mA (center of gravity is under balance status)
Holding upright:295*470*290(mm)
Handholding:370*470*400(mm)
2430gexcluding battery
320 degree unlimited rotation
Roll Axis Mechanical Moving Range
320 degree unlimited rotation
Pan Axis Mechanical Moving Range
630 degree unlimited rotation
Follow Tolerance at Static Status
Follow Tolerance at Motion Status
Minimum0.02
Maximum0.05
Minimum0.05
Maximum0.2
The Maximum Payload
Battery
Battery Type
Battery Model
Battery Capacity
Charging Time
Lithium Battery
3h (voltage input 5V/2A)
USER NOTICE Do not exceed the maximum specified load capacity (see specifications on the package label or visit www.benro.com). Always ensure the gimbals locks are tightly engaged before mount any gear on your gimbals. Do not use any Tripod below temperatures of 14F or above +113F(10C / +45C). Always clean and dry any gimbals after has been exposed to wet, dusty, sandy or salty conditions. Your gimbals are not recommended for use in water. If required, clean the gimbals using a soft cloth with some no water alcohol. Do not leave any Tripod in the sun for prolonged periods and avoid high temperature exposure. For your safety, don't let your BENRO gear come in contact with any electrical power source. LIMITED WARRANTY COVERAGE Your Benro product has been carefully manufactured, has passed many quality assurance checks and has been thoroughly tested before shipment. It is warranted in the country from which you purchased it based on the date of purchase to the original owner, against defects in materials and workmanship. The warranty does not apply to damages caused by mishandling, dropping, or leaking batteries, nor modification or servicing performed by others. Please contact your local Benro dealer for further information and details about your warranty. To find the Benro distributor in your country, please check the distributor information at Benro official website www.benro.com.
Specifications and design are subject to change without notice