FCC ID: WUP-BEST-9616 Low power alarm receiver (transceiver)

OPERATING PAIR WIRELESS ALARM UNITS FUNCTION INSTRUCTIONS By PAIRING a transmitter with a receiver, you determine which receiver is the primary recipient for that specific transmitter. The paired transmitter will always try to reach the paired receiver first. If the transmitter does not connect to the paired receiver, it will transmit to the nearest receiver. 1 2 3 Press the receiver until the light goes on. Continue to press the concealed button. At the same time, press the transmitter until it flashes, alternating between red and green. The transmitter and receiver are now paired. The transmitter can be paired with a different receiver by repeating steps 1 & 2. TRANSMITTER RECEIVER BEST TELEPRODUKTER AB | PHONE +46 (0)31 - 911 900 | FAX +46 (0)31 - 911 960 | info@best.se | www.best.se

V1.3 Datasheet BEST-9616 PROACTIVE RECEIVER Technical Description:

The BEST-9616 receiver is equipped with a quick-connect terminal in order to connect to a room unit and external LED. The unit has a switch for selecting its Group. Overview:

Connector X1:

X1.1 : + 12V X1.2 : LED ( - OUT) X1.3 : -

X1.4 : CH2 (+ OUT) X1.5 : CH1 (+ OUT) X1.6 : KV (- IN) X1.7 : NOT USED X1.8 : NOT USED Switch Sw1:

Switch to set the units Group BEST TELEPRODUKTER AB Uggledalsvgen 19, 427 40 Billdal, Gteborg Telefon +46 (0)31-911 900 Fax +46(0)31-911 960 E-mail: hq@best.se Datasheet BEST-9616 PROACTIVE RECEIVER Settings:

Sw1 Switch:

Sets the units Group (binary). The values/functions of the different switches can be seen in the tables below. Installation type:

Stand-alone (Connected to BEST-9620 for example) Sw1.6 0 Stand-alone installation:

Grouping should be by floor or by area for the best positioning. Group:

Switch:

Value:

Sw1.2 Sw1.1 1 2 Sw1.3 4 Monitoring position:

Sw1.4 Sw1.5 Function 0 1 0 0 0 1 Paired transmitter Paired transmitter & signal from its group Paired transmitter & signal from all groups Note: The unit monitors the attack transmitter regardless of the settings above. BEST TELEPRODUKTER AB Uggledalsvgen 19, 427 40 Billdal, Gteborg Tel. +46 (0)31-911 900 Fax +46 (0)31-911 960 E-mail: hq@best.se Datasheet BEST-9616 PROACTIVE RECEIVER Location:

In general the receiver should be located as close as possible to the center of the space it is intended to cover. Walls and other factors that can affect reception should be taken into account. The receiver is equipped with an advanced algorithm in order to "see" which receiver is closest to the transmitter. Bear in mind that radio waves penetrate walls. Incorrect placement can cause the receiver in another room to be the one that is actually closest. A transmitter can be paired to its own room to further reduce the potential for activating the wrong receiver. This means that the transmitter tries to reach its own receiver first before trying to reach other receivers. This provides added security. Because this is a radio-based system, exact positioning cannot be guaranteed. Instead it must be tested on-site; however, the more receivers that are installed, the better the positioning that can be expected. The illustration below shows a likely reception area. The various rings are there to be able to easily see which receiver is closest for different transmitter locations in the room. ROOM ROOM ROOM A signal from this transmitter is received by the receiver in the ROOM, because it is closest. HALLWAY KITCHEN from A signal this transmitter is received by a receiver in the room living or hallway, since they roughly an are at equal distance from the transmitter. LIVING ROOM from signal A this transmitter is received by a receiver in the ROOM, even if the receiver in the hallway is closer. This is because the transmitter is paired with the receiver in this LGH, and therefore tries to reach it first. BEST TELEPRODUKTER AB Uggledalsvgen 19, 427 40 Billdal, Gteborg Tel. +46 (0)31-911 900 Fax +46 (0)31-911 960 E-mail: hq@best.se Datasheet BEST-9616 PROACTIVE RECEIVER Adjustment:

It's possible to visually see which type of alarm activates the receiver in order to be able to set the optimal function for a particular space. This is very important for adjustment/troubleshooting. When a receiver has been activated it flashes according to the table below. Receiver activated by:

Transmitter paired with this receiver Transmitter paired with a different receiver Attack alarm LED:

Flashes slowly Steady Light Flashes quickly BEST TELEPRODUKTER AB Uggledalsvgen 19, 427 40 Billdal, Gteborg Tel. +46 (0)31-911 900 Fax +46 (0)31-911 960 E-mail: hq@best.se T-9616 P PROACTI IVE RECE EIVER sheet Datas BEST Certifi FCC ID This de followin this dev cause u cations:

D: WUP-BES ST9616 evice complie ng two condit vice must ac undesired op es with Part 1 tions: (1) this ccept any inte peration. Warning:

nvironmen es or modific e users auth FCC W Change void the The en RoHS:

This un nit is manufac acturing. manufa Direktiv ve 2002/95/E t:

EC 15 of the FC s device may erference rec C Rules. Op y not cause h ceived, includ peration is su harmful interf ding interfere bject to the ference, and ence that ma d (2) ay cations not e hority to oper expressly ap rate the equi pproved by t pment the party res sponsible for r compliance e could ctured in acc cordance wit h applicable regulations f for lead-free

(Waste Elec it may not be when discard ctrical and E e discarded i ing electroni Electronic E into the hous ic products. Equipment):

sehold trash. Check whic ch local regul lations al Voltage:

al Current:

(max.) ng:

sed mountin g:

al mounting ing height:

12 VD DC +- 15%

A 25 m 300 m mW 90 x 8 mm 90 x rol box 65 m Cont BEST T-1061 exter Ca. 2 2000 mm abo m) mm (cc 60 mm rnal frame ove the floor WEEE The un apply w Data:

Nomin Nomin Power Size:

Recess Extern Mounti BEST UKTER AB U T TELEPRODU T Tel. +46 (0)31-

-911 900 Fax Uggledalsvge

+46 (0)31-911 en 19, 427 40 1 960 E-mail:

Billdal, Gteb hq@best.se org