smartShelfTM Control Box (Model: BLD000010-000)
Installation and starting up
Thank you for deciding to purchase the smartShelfTM Control Box
The smartShelfTM Control Box is a device for contactless data exchange with common Transponder
according ISO 15693. To this it requires an external Antenna (smartShelf Antenna). The connection
to a computer or other equipment is carried out via the LAN interface.
User Manual - smartShelfTM Control Box (Model: BLD000010-000)
Technical Data
Housing
Weight
Supply voltage
Power consumption
Interface
Temperature range
• Operation
Storage
•
Relative air humidity
Antenna
Operating frequency
RF – transmitting power
Product Label
Mild Steel
5KG
100-240VAC, 50-60Hz
1.6A
LAN
-25°C to +55°C / -13°F to +131°F
-25°C to +85°C / -13°F to +185°F
5-95 % (non-condensing)
External (50 Ω ± 15 Ω < 15°)
13,56 MHz
5 W ± 1 dB
Important Note!
If you do not follow these instructions the device hardware can be damaged irreparable.
* Use this device only with a connected and tuned 50 Ω ± 15 Ω antenna! *
* Note that any metal parts around the antenna can detune the antenna! *
User Manual - smartShelfTM Control Box (Model: BLD000010-000)
Notice for USA and Canada
IC: 22443-SMARTSHELF
FCC ID: RUVSMARTSHELF
This device complies with Part 15 of the FCC Rules and with RSS-210 of ISED Canada
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Unauthorized modifications may void the authority granted under Federal communications
Commission Rules permitting the operation of this device.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Warning: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
User Manual - smartShelfTM Control Box (Model: BLD000010-000)
Safety Instructions
The device may only be used for the intended purpose designed by for the
manufacturer.
The operation manual should always be conveniently kept available for each user.
• Unauthorized changes and the use of spare parts and additional devices which have
not been sold or recommended by the manufacturer may cause fire, electric shocks or
injuries. Such unauthorized measures shall exclude any liability by the manufacturer.
The liability-prescriptions of the manufacturer in the issue valid at the time of purchase
are valid for the device. The manufacturer shall not be held legally responsible for
inaccuracies, errors, or omissions in the manual or automatically set parameters for a
device or for an incorrect application of a device.
• Repairs may only be executed by the manufacturer.
•
Installation, operation, and maintenance procedures should only be carried out by
qualified personnel.
• Use of the device and its installation must be in accordance with national legal
requirements and local electrical codes.
• When working on devices the valid safety regulations must be observed.
•
Special advice for carriers of cardiac pacemakers: Although this device doesn't exceed
the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm
between the device and your cardiac pacemaker and not stay in an immediate
proximity of the device respective the antenna for some time.
•
•
•
User Manual - smartShelfTM Control Box (Model: BLD000010-000)