BiDaE
LB60004G
User Manual
BiDaE Technology, Incorporated
Address:1F., No. 5, Ln. 96, Sec. 1, Da'an Rd., Da’an Dist.,
Taipei City 106069 , Taiwan (R.O.C.)
Email:sales@bidae.tech
http://www.bidae.tech
Regulatory Compliance Statements
FCC Warning Statement
This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference with
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference with radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to
Connect the equipment into an outlet on a circuit different from that to
‐Consult the dealer or an experienced radio/TV technician for help.
1.
This transmitter must not be co‐located or operating in conjunction with
any other antenna or transmitter.
2.
This device complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. To maintain compliance with FCC RF
exposure requirements, avoid direct contact to the transmitting antenna
during transmitting.
3.
Any changes or modifications (including the antennas) made to this
device that are not expressly approved by the manufacturer may void
the user’s authority to operate the equipment.
FCC Label Statement
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons and must not be co‐located or operating in conjunction with
any other antenna or transmitter. End‐users and installers must be
provide with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
European Conformity Statement
BiDaE Technology declares that the product is in compliance
with the essential requirements and all other provisions of the
RED 2014/53/EU directive.
CE Mark Warning
RoHS Statement
This device conforms to RoHS (Restriction Of Hazardous Substances)
European Union regulations that set maximum concentration limits on
hazardous materials used in electrical and electronic equipment.
Contents
I. Product Information ............................................................................. 1
II. Network Setup ........................................................................................ 2
II.1 - Connection with LB60004G ............................................................... 2
II.2 - Set up .................................................................................................... 2
II.3 - Connection to Wi-Fi ........................................................................... 3
II.4 - Setting Static IP ................................................................................... 4
II.5 - Setting Access Point ........................................................................... 5
I. Product Information
Exterior
RESET
Power
Ethernet port
Description
restart.
RESET When LB60004G works abnormally, press Reset button to
power 5 V,2.5A for full power delivery to USB devices
Ethernet
port
Ethernet ports for connecting the LB60004G to the local
computers
1
II. Network Setup
II.1 - Connection with LB60004G
Wireless connected by LBeacon default AP
ssid:BiDaE_AP
Or connected by Ethernet cable
II.2 - Set up
Setup Using Browser
Enter IP(default IP:192.168.2.1) in address bar and login
Username:root, No password
2
II. Network Setup
II.3 - Connection to Wi-Fi
Go to Web Setting >Network> Wireless>Scan>Join
Network>Enter“passphrase”>save>submit>save>Save &
Apply
3
II. Network Setup
II.4 - Setting Static IP
Go to Web Setting >Network> Wireless>WWAN>Edit
Select “Static address”>enter the“IPv4”>save>Save &
Apply
4
II. Network Setup
II.5 - Setting Access Point
.Setting Wireless Access Point
Go to Web Setting >Network>wireless>
Edit>change “ssid”>change “key”>save>Save & Apply
5
II. Network Setup
Setting LAN static IP
Go to Web Setting >Network> Interfaces
LAN>Edit> enter the “IPv4”>save>Save & Apply
6
II. Network Setup
Apply
Turn off LBeacon AP
Go to Web Setting >Network> Wireless>Disable> Save &
7