QUICK START GUIDE Start_Guide.indd 1 12/06/2019 16:21 About Contact This manual describes the proper use of the Bike Finder tracker and all accessories. Make sure to read this before installation and activation of the tracker. Ensure that all warnings are read and understood before use. Technical specications Product Name:
BikeFider Tracker BFG1S Model:
Network frequency: 850/900/1800/1900 Mhz, 2.4Ghz Satellite system: GPS and GLONASS Battery Rechargeable: 960 mAh Li-Ion battery, 0.5C Power bank: Input 5VDC 2.1A, Output 5VDC 2.1A/1.0A Compatibility Handlebar inner diameter:
15.1-19.9mm (mount tracker without adapter) 20.0-27.0mm (mount tracker with adapter) 15.1mm 180mm 23.3mm Requires BikeFinder subscription to function Contact support through the app, or via support@bikender.com Limitations and warranty General Safety precautions Do not bend tracker more than 45 degrees Do not insert tools or pointy objects, other than those included, into USB socket or other openings in the tracker Do not open or tamper with any internal components Do not expose the tracker to water submersion or high-
pressure water jets Do not drop tracker onto hard surfaces or expose it to high-
energy impacts Keep power bank and USB-cable away from moisture Keep tracker and accessories away from high pressure places, potentially explosive atmospheres and extreme temperature conditions (below -20 C or higher than 45 C) Keep away from medical electronic equipment When charging: use only included power bank For full terms and conditions:
www.bikender.com/terms BikeFinder privacy policy:
www.bikender.com/privacy More information and video instructions:
www.bikender.com/manual Getting started information:
https://bikender.freshdesk.com Start_Guide.indd 2-3 12/06/2019 16:21 Installation steps 1 Charge the tracker Remove USB cover and insert USB cable. A sound will come from the tracker, letting you know that it has started up. 2 Install the tracker Mount the device and make sure that the direction arrows are pointing upwards to ensure correct installation. Direction arrows 3 Lock the tracker in place Fasten the screws using the tool. Tighten the two screws evenly until tracker is locked in place. Note:
The expansion mechanism can damage the interior of the handlebar. Tip:
Recheck the fastening periodically. Start_Guide.indd 4-5 12/06/2019 16:21 4 Plug in USB cover Plug in USB cover during normal use. Your tracker is now installed and ready to use. For troubleshooting and more information, go to www.bikender.com/manual Warning!
Antenna area 5 Download the app The BikeFinder app lets you see the location of your bike You can download the app from the App Store and Google Play. First you must register using your e-mail and pair the device using the app (see step 6). The app will guide you through the necessary steps. When your device is paired and activated you can choose from numerous settings in the app. 6 Activation of the tracker To activate your BikeFinder tracker you must follow the following procedure:
1. Make sure you buy a subscription on the same account
(email) as you are using to log into your app on the phone or tablet 2. Open the app 3. Connect your tracker to your account via Bluetooth 4. The app will prompt you for activation of the tracker Start_Guide.indd 6-7 12/06/2019 16:21 FCC WARNING STATEMENT Warning: Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 4W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certication for use when properly worn on the body is 2.434w/kg. For body operation, this device has been tested and meets FCC RF exposure guidelines when used with any accessory that contains no metal and that positions a minimum of 15mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. 20mm+ handlebar adapter set Use the adapter set on handlebars with inner diameter larger than 20mm. Expansion mechanism adapter Silicone spacer Expansion mechanism adapter installation:
1. Remove the two expansion bolts using the screwdriver tool provided in the box 2. Mount the two expansion adapters and reinstall the expansion bolts Silicone spacer installation:
1. Slide the silicone spacer into the device until the spacer is located as shown to the right Start_Guide.indd 8-9 12/06/2019 16:21 Power Bank Product specications:
Product Name Battery Type Capacity Type-C Input USB Output 1 USB Output 2 Maximum Output Power Product Size Net Weight PB-12 Polymer Lithium Battery 5000mAh 5V/2.1A 5V/2.1A 5V/1.0A 10W 9.0*6.3*1.2cm 105g Indicator lights:
1. The 4 white lights in the front side of the product are battery indicator lights 2. The battery indicator can be turned on when you press the switch 3. The 4 lights display the remaining electricity quantity as 25% - 50% - 75% - 99%
4. If there is no operation in approximately 40 seconds, the battery 5. Under normal circumstances, the indicator lights will be ashing when it is in recharging mode 6. Pressing and holding the switch button for approximately 10 Product Details:
Input: Type-C The Features:
USB Output USB Output Switch Button Battery Indicator lights 1. Supports charging of two devices at the same time 2 There is a hole on the upper right corner of the product, you can attach lanyard to the hole and hang it on your bike while charging. How do you distinguish the USB output currents with 1.0A from the one with 2.1A?
1. The device will automatically recognize the correct current output on both USB ports 2. The current will be evenly distributed when both USB outputs are charging your devices at the same time. That means the current of each output is reduced to 1.0A 3. If charging other devices than the BikeFinder with the powerbank, use the USB cable supplied with the device you are about to charge. This is to ensure compatibility Start_Guide.indd 10-11 12/06/2019 16:21 Apple and the Apple logo are trademarks of Apple Inc. registrered in the U.S and other countries. App store is a service mark of Apple Inc. registered in the U.S and other countries. Google Play and the Google play logo are trademarks of Google Inc. The Bluetooth word, mark and logos are registrered trademarks owned by the Bluetooth SIG. Inc. and any use of such marks by Bikender AS is under license. Box Content Tracker Tool USB cable Power bank Adapter set Manufacturer BIKEFINDER AS KVITSYGATA 30, 4014 STAVANGER NORWAY www.bikender.com/manual Start_Guide.indd 12 12/06/2019 16:21